131,077 used machines on RESALE, but how to find them? Machine Search
Y.O.M.: 2002 Factory No.: 02050057 Power: 500 l/h, motor: 22 kW Pressure: 1000 bar as good as new with manual Dimensions LWH: 1400 x 1000 x 1250 mm Weight: 900 kg
spindle diameter: 130 mm x-travel: 3500 mm y-travel: 2000 mm w-axis: 900 mm taper ISO: 50 total power requirement: 18,5 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Wilms indoor heater new ovp Manufacturer Wilms Type B125 Diesel Oil-powered heaters with open flame, e.g. for deicing or thawing materials, vehicles, pipelines, etc. As additional heating of stables as well as of operating and storage rooms with sufficient ventilation. Electric connection: 230 V, 50 Hz. Room thermostat installed as standard. Type: B 125 Heating capacity: 40 kW - 34,400 kcal/h Air power:: 920 m3/h Consumption: 3 kg/h Tank: 38 l Weight: 24 kg
20-90-542 Multeosill Drilling Machine WOODLAND MACHINERY (new) Type: BM21S Number of shafts 21 Adjustable drilling angle Working width 700 mm Table Dimensions 1000 × 900 mm Additional support Ruler 3000 mm Number of Pressers 2 Engine power 1.5 kW 380 V 50 Hz Required Air Pressure 8 bar Drilling Step 32 mm Weight 150 kg Transport Dimensions 1200x1000x1300 mm
TABLET PRESS MANESTY BETAPRESS N° of stations: 16 Operating pressure: Max. 6.1/2 Diameter of punches: 19 mm Length of upper punch: 133.6 mm Length of lower punch: 133.6 mm Max. mechanical speed: 90.000 Height of machine: 160 mm Floor space occupied: 584 mm x 851 mm Approx. weight of machine: 695 Kilos
Compounding plant Material: PE, PP, PS, WPC + fillers / Details: segmented screws and cylinders, three-phase motor 250 kW, dcrunner, screw speed: 300 rpm, degassing, 2x busch vacuum pump, side feeding Berstorff ZSFE 120 SO, metal separator, noise protection hood, ECON air granulating system ELG 3000, control: SIEMENS S7 with visualization. Up for a surcharge: extension to 40D possible
Mono-plate system Material:PE, PP, PS, ABS. Built: 1985, last modification: 2003 Screw diameter: 100 mm, L/D 36 Extruder with degassing, vacuum pump, melt pump, hydr. Screen changer, nozzle 1350 x 1.0 - 6.0 mm, 3 rolls smoothing unit 1350 x x 350 mm with single drives, 3 temperature control units for roller temperature control, cooling section, side cut, printwith 2 rubber rollers, top and bottom protective foil lamination, cross saw 1,350 mm, switch cabinets with air conditioning, separate control panel
Bosch stainless steel dosing pumps, 12 mm (21 pcs. available)
Bosch stainless steel rotary piston pumps Ø 30 mm, long version (8 available)
Bosch stainless steel rotary piston pumps, , Ø 30 mm, short version (12 available)
Material: PVC // Details: DC motor 10 kW, screw diameter 52 mm, L/D 16, degassing, capacity: approx. 10 - 70 KG/hr.
Bühler Entoleter MJZG 51 D, Fabrication-Nr. 10256498 Includes Frame für standing mount Sockets and wear rings in good condition rinse with compressed air no magnet valve
Material: PE, PP, PS // DC motor: 132 kW, power: approx. 300 - 500 KG/hr, screw 90mm, L/D30, strand nozzle, water bath, strand granulator.
- The largest diameter of the workpiece, mm 90 - The maximum diameter of the planted flange, mm 120 - Rated force of the landing slide, kN 6300 - The force perceived by the clamping slide with closed dies, kN 6300 - stroke of the landing slider, mm 350 - The stroke of the landing slide after closing the dies, mm 230 - The frequency of continuous idle slider per minute, not less than 42 - Power of the electric motor 45 - Dimensions, mm length 4835 width 3450 height 2880
Material: PVC // with degassing, counter-rotor, DC motor 29 kW, screw diameter 86 mm, L/D 16 Capacity: 150 - 250 KG/hr
Cast Film CoEx System (ABA), PE / PP, Capacity: approx. 400 - 700 kg/h, Main extruder, 120 mm, co-extruder of 60 mm, screen changer, melt pump, Co-Ex block, nozzle 1,650 mm, 2-roll chill-roll smoothing unit, cooling section, extractor, double winder with cutting device and edge control, edge trim, film measuring device thickness NDC (without measuring head), incl. operating instructions and e-plans.
Modular built semi-automatic twist wrapping machine Product dimensions: Width: 50 - 730 mm Height: 20 - 520 mm Length: 750 mm to infinity Maximum diagonal: 730 mm Packing materials: PE stretch film, VCI stretch film PE film, crepe paper, etc. Width: up to 250 mm Core average: 76 mm Very good condition!
maximum number of results exceeded
please refine your search
