arburg 420c used for sale

Some older plastic injection molding machines from Arburg, Demag and Stübbe are available. 1) Stübbe S110/345, year of manufacture: 1976, clamping force: 1000kN, shot weight: 140g, mold installation height min./max.: 180mm/480mm, opening stroke: 320mm, tie bar spacing: 360mm/355mm, screw diameter: 40mm, core pulls: 1. 2) Demag D 150-452 NC III, year of manufacture: 1990, clamping force: 1500kN, shot weight: 207g, mold installation height min./max.: 320mm/550mm, opening stroke: 430mm, tie bar spacing: 460mm/460mm, screw diameter: 45mm, core pulls: 1. 3) Demag D 100-275 NC II P, year of manufacture: 1989, clamping force: 1000kN, shot weight: 130g, mold installation height min./max.: 200mm/400mm, opening stroke: 350mm, tie bar spacing: 400mm/400mm, screw diameter: 38mm, core pulls: 1. 4) Arburg Allrounder 270M 250-75, year of manufacture: 1990, clamping force: 250kN, shot weight: 25g, mol ...

Key data: 1500 kN, 40 mm

ARBURG ALLROUNDER 520 H 1500-400 (2015) Injection molding machine + WITTMANN ROBOT + Conveyor belt In operation Hours: 68946 h. Clamping force: 1500 kN Clamping unit 520 H Opening force / stroke: 450 mm. Fixed / variable mould mounting height: 250-550 mm. Fixed / variable platen spacing: 700-1000 mm. Column spacing: 520 x 520 mm Mold clamping platens (width x height) 695 x 695 mm. Weight of movable mould half: 1000 kg max. Force – Ejector stroke: 40 kN – 175 mm Idle cycle time: Conformt Min 1.5 – s- 364 Screw diameter: 40 mm. Effective screw length: 20 L/D Screw stroke: 160 mm. Calculated injection volume: 201 cm3 Weight per injection: 184 g. Ps. Material flow rate: 29 kg/h. PS Injection pressure: 2000 s-bar Post-pressure time: 45-2000 s-bar Injection flow: 214 cm3/s Injection speed: 170 mm/s Power – heating zones: 9.7 kW – 5 Oil capacity: 160 l. Weight ...

A fully equipped Arburg injection molding machine including clean air supply Filter Fan Unit and removal robot is available. Clamping force: 1600kN, screw diameter: 45mm, max. cylinder heating: 450°C, total connected load: 85.5kW, machine elevation: 100mm, operating hours: approx. 9171h. Arburg Multilift H: axis: B, Z-axis stroke: 1400mm, conveyor belt length: 2500mm, conveyor belt width: 600mm, deposit height range: 900mm-1300mm, temperature resistance: 160°C. Documentation available. An on-site inspection is possible.

A fully equipped Arburg injection molding machine including clean air supply Filter Fan Unit and removal robot is available. Clamping force: 1600kN, screw diameter: 45mm, max. cylinder heating: 450°C, total connected load: 85.5kW, machine elevation: 100mm, operating hours: approx. 13361h. Arburg Multilift H: axis: B, Z-axis stroke: 1400mm, conveyor belt length: 2500mm, conveyor belt width: 600mm, deposit height range: 900mm-1300mm, temperature resistance: 160°C. Documentation available. An on-site inspection is possible.

A comprehensive spare parts package for the Arburg Allrounder 221 series is available. 1) Mechanics/Hydraulics/Plasticizing: 6x ejector piston rod, 3x pressure relief valves, clamping cylinder seal kit, 5x ejector seal kit, injection unit seal kit, cylinder D30, screw D30, 20x disc spring D31,5/16,3. 2) Heating/Temperature: 6x barrel heaters 1750W, 5x nozzle heater band 600W, Thermomat, 40x thermocouples. 3) Electrical/Sensors/Switches: 2x coding switch blocks, 6x contact sensors, 5x rocker switches, 2x snap-action switches, 9x switches, 8x microswitches, 2x limit switches, 10x ejector safety switches, 4x initiators, oil level switch, 6x contact pins with contact, 2x pulse counters. 4) Electronics/Control: printed circuit board ARB 279, 2x each membrane keypad ARB 179 and 180, printed circuit board shutdown automation 141, 2x printed circuit board ARB 550, printed circuit board ARB 554.  ...

Manufacturer: Arburg Model:720S 3200/1300 Year of Manufacture: 2010 Operating hours: 84854 Closing force: 320 t Screw diameter: 60 mm Max. injection volume: 664 cm3 Fixing plate: 1030 x 1030 mm Machine weight: 17.5 t Find more here - / Contact us at -

Arburg 570C2000-800 FY2006 Golden Edition, 1 core hoist, 1 conveyor belt 33.400 Multilift SELECT 6kg Arburg 470C-2000-800 FY2005 No core features; 1 conveyor belt

2 x Arburg 320 K 700-100 injection moulding machines 2001 and 2003

This Arburg ALLROUNDER 1200 t 1000 - 400 Injection moulding machine was manufactured in the year 2018 in Germany. It has 58 production hours. The machine has a clamping force of 1000 kN, machine like new, used only for testing. Machine needs to be CE certified by the customer, we have a quote from a third party starting at 2.000€.

Injection moulding machine Arburg 820S 4000-4600 BJ 2016

This Arburg 470 A 800-170 was manufactured in 2008. A vertical injection moulding machine with a closing force of 80 tons, operating on 400 V 3∼, 50 Hz. It features a total connected load of 69 kVA. Consider the opportunity to buy this Arburg 470 A 800-170 vertical injection moulding machine. Contact us for more information.

This 3-axis Arburg Allrounder 520S 1600-400 was manufactured in 2021. It features a screw diameter range of 35-45 mm and a clamping force up to 2000 kN. The machine includes a removal robot and an enclosure with a FilterFanUnit, ensuring clean operations. Ideal for precision plastic processing, it offers a mold clamping height of 250 mm and platen spacing of 825 mm. Contact us for more information about this machine.

CONTROLS   CNC controls MOULD CLAMPING UNIT   locking force: 350 to   die opening stroke max.: 350 mm EJECTOR (TABLE EJECTOR)   stroke: 150 mm INJECTION UNIT   stroke of screw: 80 mm ELECTRICAL SPECIFICATIONS   mains voltage: 400 V   mains frequency: 50 Hz DIMENSIONS / WEIGHTS   space requirements -left/right-: 3700 mm   space requirements -front/back-: 1300 mm   total height: 2100 mm   total weight approx.: 2300 kg Features: - Includes pellet dryer: Labotek DDM 60 ALB 3 units available

This Arburg Allrounder 1200T 800-150 was manufactured in 2006. A vertical injection moulding machine, it offers robust functionality for specialized plastic processing tasks. Consider the opportunity to buy this Arburg Allrounder 1200T 800-150 vertical injection moulding machine. Contact us for more information.

Awaiting refurbishment at our headquarters in Northamptonshire is this Engel VC500/120 injection moulding machine with double pneumatic and single hydraulic core pull. Any machines awaiting refurbishment (or undergoing refurbishment) with us can be reserved with a 10% deposit and we then prioritise the refurbishment and aim to have the machine available for inspection within 8 weeks from order. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cosmetically as good as we can get them. We guarantee our refurbs are delivered fault free and leak free. Prices shown are ex-works, but we can quickly provide DAP (Delivered at Place) Inc ...

This Arburg 470 E 1000-700 was manufactured in 2011. A robust electrical injection moulding machine, it features a closing force of 100 tons and a screw diameter of 25mm. Operating on 400V 3∼, 50Hz with a total connected load of 78kW, its designed for efficient performance. Consider the opportunity to buy this Arburg 470 E 1000-700 electrical injection moulding machine. Contact us for more information.

Injection moulding machine Arburg 270s 500-60 and Boy 12 M 1998

This Arburg 420A 1000-400 was manufactured in 2007. It features electromechanical main movements by servo drives, a modular plasticizing unit with adaptive temperature control, and a five-point double toggle clamping system with servo-electric adjustment. The Selogica control system enhances operational efficiency. If you are looking to get high-quality injection molding capabilities, consider the Arburg 420A 1000-400 machine we have for sale. Contact us for more information about this machine.

This Arburg 570 S 2200-800/290 was manufactured in 2020. It features a hydraulic drive system and the Selogica control system for precise operations. With a clamping force of 2,200 kN and a screw diameter of 40 mm, it is ideal for detailed injection moulding tasks. Consider the opportunity to buy this Arburg 570 S 2200-800/290 hydraulic injection moulding machine. Contact us for more information.

Clamping angle, T-slot plate, clamping table, clamping cube, clamping plate, clamping tower, clamping box -Table comes from an injection molding machine -Make: Arburg -Type: Allrounder 320-210-750 KN -Dimensions table: 490 x 490 mm -Bore center: Ø 125 mm -Thread holes: M12 -Dimensions: 490/490/H400 mm -Weight: 236 kg

This Arburg 470 S 800-170 was manufactured in 2010. A hydraulic injection moulding machine featuring a clamping force of 80 tons and tiebar spacing of 470x470 mm. It operates on 400 V 3~ 50 Hz with a total connected load of 76 kW. Consider the opportunity to buy this Arburg 470 S 800-170 hydraulic injection moulding machine. Contact us for more information.

Tubular heater, heating tape, heating sleeve, mica heater, cylinder heater, heating cylinder, ceramic heating tape -Manufacturer: Arburg, heating band heating collar -Type: Ø50 x 34mm -Heating power: 310 W -Voltage: 220V -Number: 1x heating tape available -Price per piece -Dimensions: 220/80/H40 mm -Weight: 0.2 kg

Tubular heater, heating tape, heating sleeve, mica heater, cylinder heater, heating cylinder, ceramic heating tape -Manufacturer: Arburg, heating band heating collar -Type: Ø x 40 mm SN 52331 -Heating power: 350 W -Voltage: 230/250V -Number: 1x heating tape available -Price per piece -Dimensions: 200/130/H40 mm -Weight: 0.2 kg

Manufacturer: Arburg Model: 520S 1500/800 + Robot Type: Injection moulding machine Year of manufacture : 2010 Operating hours: 91720 Closing force: 150 t Screw diameter: 45 mm Max. injection volume: 318 cm3 Fixing plate: 688 x 688 mm Machine weight: 6.84 t Find more here - / Contact us at -

Injection moulding machine ARBURG 820 S 4000-2100 with Multilift Select (2016)

Key data: 3200 kN, 309 g/PS, 50 mm

Production Line Manufacturing Coffee Capsules NESPRESSO Consisting of the following components: Pos. 01) Injection moulds for capsules, manufacturer: FOSTAG AG 1.0 pcs tool with 16 cavities 1.0 pcs tool with 32 cavities Pos. 02) Two-component injection moulding machine, Bcobrsw Nriue Rvf Nyju Manufacturer: ARBURG, Type: 720A3200-800, Year of manufacture: 2017 The capsules are made as falling parts.

Clamping force: 1300kN, screw diameter: 40mm, max. injection pressure: 2120bar, shot volume: 182m³, shot weight: 153g, tie bar spacing: 470mm/470mm, platen dimensions X/Y: 650mm/650mm, min. mold installation height: 275mm, max. opening stroke: 850mm, centering: 125mm. Machine dimensions X/Y/Z: approx. 4600mm/1600mm/2200mm, weight: approx. 5500kg. The clamping unit shows an oil leakage at the clamping cylinder. Documentation available. An on site inspection is possible.

Ref. no.: 17540 Manufacturer: ARBURG Year of construction: 1994 Clamping unit Clamping force: 50 ton Opening stroke: 350 mm Distance between tie bars: 270 X 270 mm Mould height min.: 200 mm Platen size (h x v): 405 X405 mm Injection unit Screw diameter: 25 mm Injection volume: 67 cm³ Shot weight: 61 g Injection pressure: 2500 bar Measurements and weight Dimensions: 3,3 X 1,5 X 2,0 m Machine weight: 2400 kg Further information: Laboratory Machine with Exceptionally Low Operating Hours The offered ARBURG 270 C 500-100 was manufactured in 1994 and originates from the training and laboratory department of a university. The machine was not used in regular production and was mainly operated for educational and testing purposes. The control system shows only approximately 100 operating hours and just 867 machine cycles. The machine is equipped with a hydraulic drive system and the proven ARBUR ...

B&A REF: 9269 TON: 60 SCREW DIAMETER: 25MM SHOT WEIGHT: 45 STROKE VOLUME: 49CM3 INJECTION PRESSURE: 2240AR PLATEN SIZES: 446 X 446MM DBTB: 320 X 320MM MIN MOULD HEIGHT: 200MM MOULD OPENING STROKE: 350MM MAX DAYLIGHT: 550MM EJECTOR STROKE: 125MM AIR VALVES: 1 MOTOR: 11 HEATING CAPACITY: 4.9KW SCREW DRIVE: HYDRAULIC

Scoring Casting Machine Arburg 470C 1500-400 BJ 2006 Injection moulding machine Arburg 370H 600-290 BJ 2010

Key data: 1600 kN, 184 g/PS, 40 mm

Arburg 520S-1600-400/170 Two-component injection moulding machine with sorting flap and gas reinforcement (245) Number: 245 Availability: in stock Year of production: 2008 Producer: Arburg Condition of Injection Molding Machine: Used Screw diameter [mm]: 40/30 Injection weight [g]: 184/77 Injection pressure [bar]: 2000/2000 Clamping force [kN]: 1600 Gap spacing [mm]: 520 x 520 Plate size [mm]: 688 x 688 Control Type: Selogica Tongue: English, German Installed power [kW]: 106 Working time [h]: 80.313 Robot connection: 67 Euro Air Valve: 4x Core string: 1x Control of mold heating: 3x Feed hopper: NO

This 3s Arburg 520S-1500-400 was manufactured in 2016. It features a clamping force of 1600 kN, a screw diameter of 45 mm, and a servo-controlled dual-circuit pump system for precise movements. The SELOGICA direct control system with a 15-inch touchscreen enhances usability. Consider the opportunity to buy this Arburg 520S-1500-400 hydraulic injection moulding machine. Contact us for further details.

Key data: 2000 mm, 360 , 55

- Top condition - 570 C 2000-800 - YOC 2007 - 55 Snail - 2 Core moves - GID interface - Only sealed in January, the SGM is completely dry.

This 3s Arburg 520S-1500-400 was manufactured in 2016. It features a clamping force of 1600 kN and a screw diameter of 45 mm, making it suitable for high-temperature thermoplastics. The SELOGICA direct control system with a 15-inch touchscreen enhances usability. Consider the opportunity to buy this Arburg 520S-1500-400 hydraulic injection moulding machine. Contact us for further details.

Key data: 1500 kN, 184 g/PS, 40 mm

Arburg 470C-1500-400 Injection moulding machine with sorting flap (256) Number: 256 Availability: in stock Year of production: 2014 Producer: Arburg Condition of Injection Molding Machine: Used Screw diameter [mm]: 40 Injection weight [g]: 184 Injection pressure [bar]: 2000 Clamping force [kN]: 1500 Gap spacing [mm]: 470 x 470 Plate size [mm]: 650 x 650 Minimum mould height [mm]: 250 Control Type: Selogica Tongue: English, German Installed power [kW]: 30.4 Working time [h]: 50.512 Weight [kg]: 4850 Dimensions [mm]: 4500×1700 Feed hopper: NO Core string: 2x Robot connection: 67 Euro Air Valve: Yes

This 3-axis Arburg Allrounder 920S 5000-3200 hydraulic injection moulding machine was manufactured in 2007. It features a maximum clamping force of 5,000 kN, a screw diameter range of 70 to 90 mm, and a maximum shot weight up to 1,860 g. Consider the opportunity to buy this Arburg Allrounder 920S hydraulic injection moulding machine. Contact us for more information about this machine.

This Arburg Allrounder 630S 2500-675 was manufactured in 2003. It is a hydraulic injection moulding machine featuring a screw diameter of 45mm. Consider the opportunity to buy this Arburg Allrounder 630S 2500-675 hydraulic injection moulding machine. Contact us for more information.

Hydraulic injection moulding machine manufactured in 2014. This Arburg 470 H 1000-170 features a closing force of 100 tons and a screw diameter of 15/25 mm. It includes a selection unit and a single platen design, with a beam spacing of 470 x 470 mm. If you are looking to get high-quality injection moulding capabilities, consider the Arburg 470 H 1000-170 machine we have for sale. Contact us for further details.

Key data: 250 kN

Arburg 221KS 250-75 / Universal machine Year of Make: 1999 Injection unit: Screw diameter: 20 mm Injection weight: 26 g Spray pressure: 2350 bar Dosing volume: 31 ccm Clamping unit: Clamping force: 25 t Tiebar spacing: 221 mm Size of the clamping plates: 342x250 mm Ejector: hydraulic Clamping unit: toggle lever Control: SELOGICA Additional equipment: Universal machine - injection unit can run both vertically and horizontally Control with air valve Core train control Hardened injection unit - Bimetal Clamp for fastening the injection unit vertically Dimensions: Weight: 1150 kg Length/Width/Height: 2.63x1.34x1.93 m Drive: Pumps/motor: 5.5 kW Heating power: 4.6 kW Total power: 10.1 kW All offered machines are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected machine or to  ...

An Arburg plastic granulate dryer with integrated material conveying is available. Hopper volume: 100l, max. drying temperature: 150°C, heating capacity: 4.5kW, air capacity: 90m³/h, conveying height: approx. 3000mm, machine dimensions X/Y/Z: approx. 950mm/600mm/2000mm, weight: approx. 150kg. An on-site inspection is possible.

Key data: 350 kN

Arburg 220M 350-90 Year of Make: 1997 Injection unit: Screw diameter: 25 mm Injection weight: 41 g Spray pressure: 1860 bar Dosing volume: 49 ccm Clamping unit : Clamping force: 35 t Spar spacing: 221x221 mm Size of the clamping plates: 346x346 mm Ejector: hydraulic Clamping unit: hydraulic Control: MULTRONICA Additional equipment: Perfect technical condition Operating hours: 19,000 hours The machine worked in a company that produced packaging for the food industry Dimensions: Weight: 1620 kg Length/Width/Height: 3.30x1.70x1.94 m Drive: Pumps/motor: 11 kW Heating power: 4.6 kW Total power: 15.6 kW All offered machines are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected machine or to participate in live technical tests at our company in Łódź. Price: On request

B&A REF: 9235 TON: 320 SCREW DIAMETER: 55MM SHOT WEIGHT: 434 STROKE VOLUME: 474CM3 INJECTION PRESSURE: 1650AR PLATEN SIZES: 1040 X 1040MM DBTB: 720 X 720MM MIN MOULD HEIGHT: 300MM MAX MOULD HEIGHT: 800MM MOULD OPENING STROKE: 600MM MAX DAYLIGHT: 1400MM EJECTOR STROKE: 250MM CONTROLS: SELOGICA TOUCH CORE PULLING: 1 AIR VALVES: 1 MOTOR: ALL SERVO DRIVES SCREW DRIVE: ELECTRIC

B&A REF: 9289 TON: 320 SCREW DIAMETER: 60-35-30MM SHOT WEIGHT: 607H / 132P / 97S STROKE VOLUME: 644 / 144 / 106CM3 INJECTION PRESSURE: 2000 / 2000 / 2500 AR PLATEN SIZES: 1040 X 1040MM DBTB: 720 X 720MM MIN MOULD HEIGHT: 300MM MAX MOULD HEIGHT: 700MM MOULD OPENING STROKE: 700MM MAX DAYLIGHT: 1400MM EJECTOR STROKE: 250MM CONTROLS: SELOCIA TOUCH CORE PULLING: 3 AIR VALVES: 2 MOTOR: SERVO HEATING CAPACITY: 22 + 7.7 + 7.7KW ROBOT INTERFACE: EUROMAP 67 ROBOT: MULTILFT SELECT 15KG QUER SCREW DRIVE: ELECTRIC HOT RUNNER: 18 ZONE ACCYMULAQTED: 6

Key data: 2000 kN, 55 mm

Clamping force: 200t Year of Make: 2002 Injection Unit .../675 Screw diameter 55 mm Spec. Spray pressure 2080 bar Injection volume 427 cc Clamping unit 2000/... Clamping force 200 t Size of the clamping plates 950 x 950 mm Lights spar spacing 570 x 570 mm Tool installation height 300 mm Opening way 650 mm Max. panel spacing 950 mm Year of construction 2002 Control type Selogica

Key data: 1000 kN

ARBURG ALLROUNDER SELECTA 470 S 1000 – 675 (Year 2001) Serial number: 187132 – Machine 8 Clamping force: 1000 kN Distance between tie bars: 470 x 470 mm Platen size: 637 x 637 mm Max. mould height: 750 mm Ejector force: 40 kN Ejector stroke: 175 mm Shot volume: 675 cm³ Operating voltage: 400 V – 3 Ph – 50 Hz Heating capacity: 14.9 kW Pump motor: 1 x 22.00 kW Total connected load: 36.9 kW Dimensions: 4180 x 1645 x h, 2140 mm. Machine weight: 5400 kg

Key data: 500 kN

ARBURG ALLROUNDER CENTEX 320 C 500 – 250 (Year 2002) Serial number: 188161 – Machine no. 30 Clamping force: 500 kN Distance between tie bars: 320 x 320 mm Platen dimensions: 446 x 446 mm Injection unit (EUROMAP): 250 Approx. shot volume: 106 cm³ Shot weight (PS): 97 g Operating voltage: 400 V – 3 Ph – 50 Hz Heating capacity: 6.5 kW Pump motor: 1 x 15.00 kW Total connected load: 21.5 kW Machine weight: 2330 kg

Clamping force: 1000 kN. Distance between tie bars: 470 x 470 mm. Platen size: 637 x 637 mm. Max. mould height: 750 mm. Ejector force: 40 kN. Ejector stroke: 175 mm. Shot volume: 675 cm³. Operating voltage: 400 V – 3 Ph – 50 Hz. Heating capacity: 14.9 kW. Pump motor: 1 x 22.00 kW. Total connected load: 36.9 kW Dimensions: 4180 x 1645 x h. 2140 mm. Machine weight: 5400 kg. Serial number: 187133 – Machine 9

This 6-axis Arburg Allrounder 520 S 1600-290 / 290 was manufactured in 2015. It features a highly wear-resistant thermoplastic cylinder with a 30 mm diameter and a drive unit powered by a 30 kW motor. The machine is equipped with advanced control systems for both injection units and supports multi-component processing. If you are looking to get high-quality injection moulding capabilities, consider the Arburg Allrounder 520 S 1600-290 / 290 hydraulic injection moulding machine we have for sale. Contact us for further details.

This 3-axis Arburg 820 S 4000-2100 hydraulic injection moulding machine was manufactured in 2016. It features a clamping force of 4000 kN, a platen size of 1171 x 1171 mm, and a maximum mould installation height of 850 mm. With a screw diameter of 70 mm and an injection unit of 2100, this machine is well-equipped for high-quality moulding capabilities. Consider the opportunity to buy this Arburg 820 S 4000-2100 hydraulic injection moulding machine. Contact us for further details.

Hydraulic injection moulding machine manufactured in 2005. This Arburg SELECTA 820 S 4000 - 3200 features a clamping force of 4000 kN and an opening stroke of 700 mm. The machine has a platen size of 1171 x 1171 mm and a maximum moving platen weight of 4500 kg. If you are looking to get high-quality injection moulding capabilities, consider the Arburg SELECTA 820 S 4000 - 3200 machine we have for sale. Contact us for further details.