angle used for sale

Specifications: - working width 2540 mm - max. cutting capacity St 40 4 mm - mot. Cutting angle adjustment - Cut gap. by scaled adjustment screws - Number of hydraulic holders 14 pcs - Mot. backgauge with positioning. 10 - 1000 mm - Stroke rate depending on cutting angle and cutting length 23 per min - Hydraulic drive 400 V / 7.5 kW - Table height 1030 mm - Space requirement approx. W 2500 x H 1630 x D 2150 mm - Weight approx. 3600 kg - with: - Sheet metal holding pneum. supported - front angle stop + support arms - Electronic cutting depth adjustment - Cut line lighting - E-foot switch

ERMAK CNC HVR 3100 x 13 hydraulic guillotine shears built in Turkey in 2008, are designed for cutting workpieces made of among others mild steel or stainless steel. The metal sheet with a maximum length of 3100 mm and a maximum thickness of 8 mm (plain steel) or 13 mm (stainless steel), is held during machining by 14 hydraulic clamps. The angle of the cutting blade can be freely adjusted in the range from 0.5° to 2.0°. Full control over the operation of the CNC HVR 3113 machine is guaranteed by the control panel located on the guillotine shears body with installed CYBELEC DNC 60 CNC controller, allowing programming of many different machining processes. The guillotine shears is equipped with among others new cutting blades and a foot control pedal, making the operator’s work much more comfortable and simple. The total weight of the machine is 13400 kg. The total weight of the mach ...

For sale complete plant for wood pellet production, made from CPM, capacity 6t/h. A most of the maschines from line are produced in between 2008-2010.y., except presses for making pellets (its bit older then rest of the line, but completly renewed before restarting. Line is consisting from: 1.Chain conveyer for logs transport. 2.Lift with angle platform for dosing material. 3.Entrance belt transporter with magnetic section for detection of iron. 4.Grinder (hammer mill) BRUKS 500kW 5.Verticaly basket transporter for chip wood. 6.Horisontal belt transporter for chip wood with three side ejectors into depoos (separated with type of the wood) 7.Hidraulic floor platform for dosing wood chips (three pcs.) with all instalation and system of hidraulic pistons. 8.Horisontal belt transporter for transportation material on drying. 9.Repler transporter for driving wood chips into fire plac ...

pressure: 80,0 / 110 t punching cross-cut in cmm: 27,0 in 20 mm L-beam: 120 x 13 mm L-beam: T 120 x 12 mm shear: flat material: 500x18 / 400x19 mm throat: 510 mm work height max.: 1050 mm total power requirement: 6,5 kW weight: 1650 kg range L-W-H: 1750 x 850 x 1850 mm very good condition () Furnishing: - hydraulic, combined profile steel shears with release station with punching station .. punching capacity 800kN Flat steel shears .. Shear capacity 100kN Angle steel scissors Angle steel knife for cutting 90 ° & 45 ° miters Cutting angle steel + T-steel + I-steel - Support table at the notching station - Scraper at the punching station - Freely movable foot switch - Central lubrication - Safety devices - Operating instructions (PDF) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

-Exhibition Machine- State-of-the-art fully hydraulic folding machine. Extensive standard equipment: · hydraulic drive for upper and bending beam · Pointed rail 45 degrees · Rails in upper, lower and bending beam · Oil filling · Control panel with: Digital display of bending angle infinitely variable specification of the bending angle Push button for controlling the upper and bending beam Switch for automatic operation · Control: PLC - Siemens · Foot switch for manual and automatic operation · CE certification · Safety stop at approx. 25 mm upper beam height Hydraulic dynamic crowning Motorized backgauge (1000 mm) Electr./hydr. adjustment of the bending wing, Touch screen: Input for backgauge values and Bending angle of the folding machine Pressure regulation of the upper beam Automatic tool clamping Round bending function with bending Half-shells 180 ...

Vollmer CHHF 21 H - Machine for single-sided grinding Year of construction: 1989 S/N 907 Make: Vollmer Germany in good working condition The technical data of the CHHF 21H at a glance: Circular saw blades Outer diameter 80 to 700 mm Bore diameter 20 to 105 mm Tooth pitch from 8 mm Hook angle up to 30° Radial clearance angle -7° to +3° Tangential clearance angle up to 5° Connected load approx. 0.52 kW Weight approx. 85 kg Dimensions: 70 x 50 x 80 cm Cisei8tfrg This machine has been specially designed for the repair of lack of carbide teeth. Newly inserted tips are used in the existing teeth. With this tabletop version, VOLLMER offers a a particularly economical, space-saving solution. The CHHF 21 H works according to the wet grinding process. During the grinding process, the grinding unit manually moved over the tooth flanks, with the saw blade Saw blade ...

KENYO VS80160 5-axis Machining center with CE Producer: Nanjing Kenyo Precision Machine Manufacture Co., Ltd YOM 2015 Simultaneously 5 axes Total Installed Capacity 22.4 kW 5-Axis vertical Milling machine for blanks up to 1000-1500kg Stroke X/Y/Z- 1600/800/800 mm Working table size 800x1800 mm Diameter of NC swivel table axle C 630 mm Rotating mass clamping force 4000 Nm Spindle clamping force: ≥ 2000 Nm Maximum mass load 2000 kg Spindle diameter 170 mm Spindle rotation angle- ± 110 Degree Tool Store Type BT40 ISO Tool magazine 24 pcs Maximum spindle rotation speed 10.000 rpm Spindle power 15 kW Ball-Screw pair HIWIN Spindle Hesheng Ball Bearings NSK Positioning accuracy ≤ X/Y/Z: 0.015 mm, C: 0.002 degree, B: 0.002 degree Repeat accuracy ≤ X/Y/Z- 0.01 mm, C:0.0015 Degree, B:0.0015 Degree Quick move: ≥ 10000 mm/min Milling speed: ≥ 1 to 8000 mm/min OC ...

GEKA BENDICROP 60 SD ironworker machine was manufactured in 2016 in Spain. Equipped with 5 work stations, the ironworker machine performs precise hole punching, corner cutting, flat bar cutting, as well as bar cutting and bending. The vertical movement of the shears is performed by two adjustable hydraulic cylinders with a central positioned actuator, which guarantees excellent cutting quality throughout the entire life of the machine. The GEKA ironworker machine weights 1750 kg. Technical specifications of the GEKA BENDICROP 60 SD hydraulic ironworker machine General data - maximum press force: 60 t - number of cylinder strokes: 32/min - dimensions (L x W x H): 2010 x 1400 x 2006 mm - weight of machine BENDICROP 60 SD: 1750 kg Hole punching station - maximum bore size (diameter x thickness): ø 40 x 11 mm - throat depth: 500 mm - additional table for hole punching fi 100 ...

workpiece weight: 100 - 3.000 kg workpiece length: 5.000 mm diameter: 1.260 - 1.600 mm Control: CAP920 total power requirement: 11 kW weight of the machine ca.: 20 t dimensions of the machine ca.: 20 Container m Mobile balancing system SCHENCK for use anywhere in the world The balancing system is permanently installed in a 20 open-top container. The container is equipped with everything you need for balancing • Lighting • Metal base plate 12,000 kg as a base plate for accuracy • Compressor for working air supply distributed in the container • Compressed air connections. • A circumferential power strip • A tool cabinet equipped with tools • A hydraulic lifting device for aligning the container from the outside • In addition to a tarpaulin for the roof, the container also comes with movable roof segments made of sheet metal. • The container has a central plug through whic ...

automatic, angle welder CMW/AL 80/60 with shrink tunnel CMS 60 - used - : Prices from location: 5.950.-€ (net) Manufacturer: Meurer Automatic angle welder CMW/AL 80/60 with shrink tunnel CMS 60 Year of construction 1996 Machine No.: 4.0514.04.96 Type plate shrink tunnel: Type: CMS 60 Angle welders: CMW/AL 80/60 The product may have the following maximum dimensions: 80 cm x 60 cm x 20 cm height. Output: Average 3000 pieces/hour The first part of the machine welds the film and the second part (the shrink tunel) makes the film smooth. Depending on the characteristic and size of the items, you can adjust the speed, quality of the welding and smoothness of the film. The control module and placed over the infeed belt (left part of the machine). Condition: good, but existing errors: Film processing must be accompanied manually because a spare part for automation is not av ...

MAAD HSSM 1550/1.5 folding machine which was built in Poland in 2017, is designed for folding thin steel sheets with a maximum thickness of 1.5 mm along a straight line at a specific angle. This functional machine, based on an innovative design, guarantees comfortable operation and a wide range of applications, which makes it ideal for many different industries. The MAAD segment folding machine has a clamping bar and a bending bar equipped with interchangeable segment knives of different lengths. Mounted on inbus screws, the segments are made of the highest quality steel, which ensures long-lasting operation of the machine while maintaining excellent bending parameters. After pressing a button on the control panel, the HSSM 1500/1.5 electric segment bending machine operates in automatic mode. The bending bar moves to the set angle and then returns to its initial position. The total we ...

Specifications: - Bending performance - Pipe at 45 kg / mm² Ø 6 - 48 mm - Solid material up to approx. 30 mm - bending angle 180 ° - Bending radius 2 x D - Drive 400 V / 1.5 kW - Space requirement approx. W 4500 x H 1400 x D 1000 mm - Weight approx. 600 kg - with - Digital bending angle display + bending angle fine adjustment - Mandrel bending device 4.5 m. with hydr. Retreat - Bending tools 16 , 25 , 20 , 33.7, 38 mm - Bending blade 3000 mm

Specifications: Uniform spindle spacing: 32 mm Number of spindles: 23 Distance between the first and last spindle on the drill head: 672 mm drilling depth: 80 mm Table size: approx. 900 x 545 mm size of the workpiece: 800 x 2500 x 100 Working pressure: 0.6 MPa Air consumption: 10 NL/cycle Voltage, frequency: 400 V/50 Hz Spindle speed / min.l: 2800 rpm. Motor power: 1.5 kW Weight ca: 400 kg Dimensions: 1220 x 1065 x 1400 mm Patented spiral system Programming and adjustment devices of horizontal and vertical Drilling depth. Pneumatic drill head shears Drill head frame of 0-90 degrees with blocking in any position and reference switching angle with each angle Head with quick-connect spindles (the quick-release buckets are a Zubehoer). 5 quick-release buckets are standard. 2 patented pneumatic pressure devices accident-protected. 2 side connectors on the table ...

No hidden costs with us The advertisement concerns the basic version of the machine. You can get all prices and extras by contacting our technical and sales representatives. We always provide the final amount on quotes if the contract is signed within the valid period. We always quote the cost of shipping from our warehouse in Poland. Hydraulic press brake PBO-3212-CNC OT-41 Specifications - Nominal pressure: 1250 kN - Max working length 3200 mm - Throat depth: 320 mm - Max stroke: 120 mm - Daylight: 390 mm - Distance between side frames: 2700 mm - Max backgauge distance: 600 mm - Nominal motor power: 7.5 kW - Length: 3700 mm - Width: 1800 mm - Height: 2450 mm - Weight: 7000.0 kg Tools - Front supports: 2 pcs - Automatic backgauge distance regulation (X-axis): servo motor - Ram control (Y-axis): servo motor - Finger height adjustment (R axis): manual - Type  ...

No hidden costs with us The advertisement concerns the basic version of the machine. You can get all prices and extras by contacting our technical and sales representatives. We always provide the final amount on quotes if the contract is signed within the valid period. We always quote the cost of shipping from our warehouse in Poland. Hydraulic press brake PBO-3216-CNC OT-41 Specifications - Nominal pressure: 1600 kN - Max working length 3200 mm - Throat depth: 320 mm - Distance between side frames: 2600 mm - Max backgauge distance: 615 mm - Nominal motor power: 11.0 kW - Length: 3400 mm - Width: 1800 mm - Height: 2500 mm - Weight: 9000.0 kg Tools - Front supports: 2 pcs - Automatic backgauge distance regulation (X-axis): servo motor - Ram control (Y-axis): servo motor - Finger height adjustment (R axis): manual - Type of punch holder: AMADA quick-action clamp ...

Specifications: - working width 4080 mm - max. cutting capacity St 40 6 mm - hydr. Cutting angle adjustment - man. Cutting gap adjustment - Stroke rate depending on cutting angle and cutting length approx. 20 - 25 per min - Backgauge with positioning control ELGO 10 - 1000 mm - Cutting length adjustment - 17 pcs. Hydraulic hold-downs - front angle stop - front support arms - Drive 400 V / 9 kW - Foot switch - Space requirement without support arms approx. W 4450 x H 1900 x D 2300 mm - Weight approx. 10500 kg

Salvagnini S4.40 punching machine with shear system  CNC control: Salvagnini SysCon Specifications: Working area: 4064x 1803 mm Max dimension of the sheet: 4064x 1803 mm Min dimensions of the sheet: 370x 300 mm Min and Max Thickness: 0.5 -5 according to the material used Maximum weight of the sheet: no limit Grippers for automatic positioning of the blehe: 13x Technology: Multi-press punching head with hydraulic drive Time for the replacement of the punching tool: 0 sec (each tool is ready for use= Simulation Possibility of activating two or more punching units Weight : 19000 kg Machine dimensions: 9967x6426 mm Power 63kW Air supply: 5 bar Punching Productivity & Cutting Productivity  Maximum material thickness: Alumumuim with breaking strength 200M/mm²: 5.0 mm Steel with breaking strength 410N/mm² : 3.5 mm Stainless steel with breaking strength 680 N/mm²:  ...

plate thickness: 4,0 mm ST plate thickness: 3,0 mm VA table-size: 1200 x 780 mm blade length: 200 x 200 mm strokes per minute: ca. 60 min angle adjustable from - to: 15 - 150 Grad engine output: 4,0 kW weight of the machine ca.: 1200 kg dimensions of the machine ca.: 1700 x 1000 x 1500 mm Furnishing: - electro-hydraulic notching machine, with angle adjustment 15° - 150° Angle adjustment by hand wheels - front panel - Plexiglas protection for better transparency - hardened knives also for cutting stainless steel - planed table surface to avoid tilting or slipping of the metal sheet - 2x staking stops with movable and interchangeable stop bars - lateral clippings ejection - free-moving footswitch - Operation manual The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

0: 2750 mm Working height: 2500 mm 0: 300-1000 mm RUCHSER glazing and sealing table RU-SW3-90° year of manufacture 2022 ----------------------------------------------------- Vertical work table with lifting device and turning device. Especially Suitable for glazing and sealing wooden windows on both sides. Furnishing: System part covered with felt Infinitely variable pneumatic lifting device, Stroke of 300 mm - 1000 mm, based on roller conveyor height Turning device for sealing on both sides, with roller conveyor 150 mm roll length 2 pneumatic tensioners for clamping the window to the turning device Version with special turning device for pushing through the on the Roller conveyor set up window with applied (closed) turning device Equipment demonstration machine, alternative/optional equipment on request! Pos. 1.0: Item no.: 1000000 RU-SW3-90° vertical work table for Wooden window with ...

sheet width: 3100 mm plate thickness: 13,0 mm thickness at Niro-steel: 8,0 mm down holder: 14 Stück no. of strokes: 11 - 20 Hub/min oil volume: 310 ltr. cutting angle: 0,05 - 2,0 ° throat: 350 mm table height: 900 mm total power requirement: 22,0 kW weight of the machine ca.: 13.300 kg range L-W-H: 5.110 x 2.570 x 2.400 mm -------------------------------------------------- heavy electr. / hydraulic CNC guillotine shears - guided by a backdrop with CYBELEC CNC touch screen control with electr. / hydr. Cutting gap and cutting angle adjustment -------------------------------------------------- Furnishing: - CNC guillotine guiding shears - with electr. / hydr. Cutting gap and cutting angle adjustment - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, includi ...

offer 22537 Specifications: - working width 4040 mm - cutting capacity St 40 6 mm - Cutting angle hydro.adjustable 0.5 - 3 ° - Cutting gap adjustment hydr. - Number of hydraulic hold-downs 22 pcs -Mot. – Backgauge with positioning control 10 - 1000 mm - front angle stop + support arms - Stroke rate depending on cutting angle and cutting length 7 - 15 p/min - Hydraulic drive 400 V / 7.5 kW - Pneumatic connection 6 bar - Table height 770 mm - Space requirement approx. W 5100 x H 2250 x D 2150 mm - Weight approx. 9000 kg - with: - E-foot switch - Cutting line lighting - Pneumatically supported sheet metal lifting

No hidden costs with us The advertisement concerns the basic version of the machine. You can get all prices and extras by contacting our technical and sales representatives. We always provide the final amount on quotes if the contract is signed within the valid period. We always quote the cost of shipping from our warehouse in Poland. Hydraulic press brake PBO-2580-CNC OT-41 Specifications - Nominal pressure: 800 kN - Max working length 2500 mm - Throat depth: 250 mm - Max stroke: 120 mm - Daylight: 320 mm - Distance between side frames: 1900 mm - Max backgauge distance: 600 mm - Nominal motor power: 5.5 kW - Weight: 4200.0 kg Tools - Front supports: 2 pcs - Automatic backgauge distance regulation (X-axis): servo motor - Ram control (Y-axis): servo motor - Finger height adjustment (R axis): manual - Type of punch holder: AMADA quick-action clamping Otinus CN ...

tube diameter: 60 mm wall strength: 3 mm bending radius min.: 2 x Rohr-Ø ÷ R200 mm bending angle: 0 - 180 ° gas tube pipelines: 2 (60.,3mm) mm speed: stufenlos 0,5 - 2,0 total power requirement: 1,5 kW weight of the machine ca.: 0,7 t - Powerful mandrel bending machine up to 2 gas pipe (60.3mm) in semi-automatic design (6000 mm pipe slide length) - Electromechanical drive of the bending axis - hydraulic clamping - mandrel feed / extract - 30 programs x 9 bending angle + correction angle The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2050 mm plate thickness: 2 mm strokes per minute until: 38 cutting angle: 1,75 ° table height over floor: 870 mm total power requirement: 3 kW weight of the machine ca.: 1520 kg range L-W-H: 2,2 x 0,6 x 1,2 m Electric 380 Volt: Back stop with manual adjustment: Shadow line lighting: Foot switch: The new motor guillotine type SMP is a well dimensioned machine with all-welded link guides. The drive takes place with a Standard geared brake motor via a chain connection to the main axle. the Knives are of the highest quality. The optimal cutting angle secures the Together with the rubber-covered blank holder perfect cuts. Bearings and guides are maintenance and lubrication-free. Standard equipment: • Back gauge 665 with mm scale. • cutting edge lighting. • Section counter. • Table extensions 600 mm. • Right angle stop, left. • Movable 24 V foot switch with emerge ...

sheet width: 2050 mm plate thickness: 3 mm strokes per minute until: 35 cutting angle: 2,0 ° table height over floor: 870 mm thickness at Niro-steel: 2 mm total power requirement: 4 kW weight of the machine ca.: 1550 kg range L-W-H: 2,5 x 1,57 x 1,21 m Electric 380 Volt: The new motor guillotine type SMP is a well dimensioned machine with all-welded link guides. The drive takes place with a Standard geared brake motor via a chain connection to the main axle. the Knives are of the highest quality. The optimal cutting angle secures the Together with the rubber-covered blank holder perfect cuts. Bearings and guides are maintenance and lubrication-free. Standard equipment: • Back gauge 665 with mm scale. • cutting edge lighting. • Section counter. • Table extensions 600 mm. • Right angle stop, left. • Movable 24 V foot switch with emergency stop. • Motor protection switch and ...

diameter: -- mm workpiece length: -- mm work piece width: 18 mm range of angles: 15° - 50° ° weight of the machine ca.: 110 kg Chamfering system UZ18 HARDWORKER Maximum bevel width 18 mm with automatic feed The UZ18 Hardworker machine is one of the most powerful automatic feed beveling machines on the market. It is not only suitable for workshops, but also for on- site assembly. The machine has a stepless working angle adjustment system. Thanks to the special design of the drive system, the UZ18 Hardworker is also suitable for harder materials. The machine is equipped with the automatic feed. Working with UZ18 Hardworker is therefore very convenient. For conventional steel (up to 600 MPA/87022 PSI strength), brass, copper and aluminum materials For chamfering workpieces with the minimum dimensions of 70 x 150 x 6 mm Application range of sheet thickness 6 - 40 mm The bevel angle can ...

Precision Deburring Faceting Milling Machine / Edge Milling Machine Specifications: Steel – stainless steel – aluminium – plastic – machining Deburring and faceting process is carried out with milling cutter Support angle - facet angle tiltable Facet angle adjustment 15 to 45 ° Facet width infinitely adjustable 0 to 7 mm Length of guide strip 500 mm Speed 2750 rpm Drive 400 V / 0.7 kW Space requirement approx. W 650 x D 600 x H 950 mm Weight approx. 30 kg

plate thickness: 4,0 mm ST plate thickness: 3,0 mm VA table-size: 1200 x 780 mm blade length: 200 x 200 mm strokes per minute: ca. 60 min angle adjustable from - to: 15 - 150 Grad engine output: 4,0 kW weight of the machine ca.: 1200 kg dimensions of the machine ca.: 1700 x 1000 x 1500 mm Furnishing: - electro-hydraulic notching machine, with angle adjustment 15° - 150° Angle adjustment by hand wheels - front panel - Plexiglas protection for better transparency - hardened knives also for cutting stainless steel - planed table surface to avoid tilting or slipping of the metal sheet - 2x staking stops with movable and interchangeable stop bars - lateral clippings ejection - free-moving footswitch - Operation manual Machine link : http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=1008 -9397088 The data for this ad was created with ModulMWS - the software solution of  ...

sheet width: 1270 mm plate thickness: 1,75 mm ST plate thickness: 2,00 mm ALU plate thickness: 2,50 mm KU thickness at Niro-steel: 0,80 mm distance between columns: 1300 mm daylight opening: OW ~ 380 mm work height max.: 900 mm adjustment: UW 60,0 mm bending angle max.: 180 ° weight: ca. 200 kg kg range L-W-H: 2000 x 520 x 1500 mm good condition () Bending splint e.g. reground Furnishing: - robust, manual folding machine - manual lifting by hand lever (incl. gas pressure damper) - manual clamping of the upper beam by means of a handwheel on the side - manual lower beam adjustment - Bending angle fixed stop, with analogue angle display - Upper beam with large opening width - Instructions / description Machine link : http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=1008 -9355182 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

THE MACHINE CAN BE VIEWED AT THE LOCATION D- 99868 GOTHA BY APPOINTMENT. Specifications: - max. working width 4050 mm - max. cutting capacity St 40 4 mm - hydr. Cutting angle adjustment - Number of strokes depending on cutting angle and cutting length approx. 20 - 25 pro/min - Motor backgauge 10 - 1000 mm - Cutting length adjustment - Hydraulic hold-downs - front angle stop - front support arms - Rear space protection - Pneumatic connection 6 bar - Drive 400 V / 9 kW - Foot switch - Space requirement without support arms approx. W 4450 x H 1900 x D 2100 mm - Weight approx. 9000 kg

Measuring tool set, 6 pieces GARANT DIN874 / DIN 875 1x Hair ruler No. 460095 size 100 1x Hair Angle No. 4 50010 Size 75 x 50 1x each Cutmaker hair angle No. 450040 Size 25 x 20 and size 40 x 28 1x gauge size marking tip 60×8×8 mm 1x stop angle, Accuracy 0, 150 x 100 mm 2x wooden box used, tested ! Dimension ( wooden box 1 ): 178 x 115 x 32 mm dimension ( wooden box 2 ): 180 x 135 x 40 mm

plate thickness: 4,0 mm ST plate thickness: 3,0 mm VA table-size: 1200 x 780 mm blade length: 200 x 200 mm strokes per minute: ca. 60 min angle adjustable from - to: 15 - 150 Grad engine output: 4,0 kW weight of the machine ca.: 1200 kg dimensions of the machine ca.: 1700 x 1000 x 1500 mm Furnishing: - electro-hydraulic notching machine, with angle adjustment 15° - 150° Angle adjustment by hand wheels - front panel - Plexiglas protection for better transparency - hardened knives also for cutting stainless steel - planed table surface to avoid tilting or slipping of the metal sheet - 2x staking stops with movable and interchangeable stop bars - lateral clippings ejection - free-moving footswitch - Operation manual Machine link : http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=1008 -9397092 The data for this ad was created with ModulMWS - the software solution of  ...

sheet width: 1050 mm plate thickness: 8,0 mm distance between columns: 1250 mm angle adjustable from - to: 0 - 180 Grad upper clamping bar adjustment: 350 mm traversing speed: OW 4,4 mm/sek Control: ELGO TYP 86 back stop - adjustable: max. 1000 mm engine output: 5,5 kW weight of the machine ca.: 3200 kg range L-W-H: 1900 x 2600 x 1600 mm maintained condition with a lot of bending tools () Pointed rails, radius rails, bending rails, divided goats foot rails etc. Furnishing: - heavy duty heavy duty folding machine, easy to operate - Angle adjustment via electric potentiometer - ELGO NC control unit TYPE 86 for electric backgauge - NC electric backgauge, with rear sheet metal support surface - electric/motorized bending beam - Electric/motorized upper beam .. max. 350 mm - manual lower beam adjustment .. max. 125 mm - manual bending beam adjustment .. max. 125 mm - Upper beam with 2x gui ...

Offer 22408 Specifications: - max. working width 3050 mm - max. cutting capacity St 40 10 mm - Projection 270 mm -Cutting angle° - Cutting gap adjustment by hand - Number of hydraulic hold-downs 16 pcs - Mechanical backgauge 20 - 650 mm - Front angle stop + support arms - Stroke rate depending on cutting angle and cutting length 7 - 12 per/min - Hydraulic drive 400 V / 22 kW - Table height approx. 820 mm - Space requirements incl. back gauge, without front support arms -ca. W 3850 x H 2000 x D 2000 mm - Weight approx. 8500 kg - With: - E-foot switch - Cutting line illumination

sheet width: 3050 mm plate thickness: 10,0 mm thickness at Niro-steel: 6,0 mm cutting angle adjustment: 0,5 - 2,5 ° cutting gap adjustment: 0,05 - 1,0 mm back stop - adjustable: 10 - 1000 mm adjustment speed: 180 mm/s down holder: 14 Stück strokes per minute: 12 - 25 oil volume: 300 Liter 0: max. 300 bar voltage: 400 V main drive: 18,5 kW weight of the machine ca.: 10.000 kg. dimensions of the machine ca.: 4080 x 2350 x 2060 mm maintained condition () was serviced annually by the manufacturer TRUMPF / EHT Furnishing: - Baffle-guided metal sheet shears with automatic cutting angle adjustment - Machine frame is an all-steel welded construction Side stands are connected to the machine table - EHT / ELGO CNC control model P-9724, front left control panel for backgauge adjustment and program selection (4 axes) - Automatic cutting angle adjustment - Automatic cutting gap adjustment - Aut ...

thread dia.: M6 - M36 turning speeds: 30 - 150 U/min working area: max. 1200 R angle adjustable from - to: 0 - 90 Grad voltage: 230 V engine output: 1200 W weight: 65,0 kg - Includes quick-change chuck - for using taps - for through and blind holes - Schwenbkare motor unit for thread cutting - at any desired angle between 0° and 90° - Higher accuracy compared to manual thread cutting - Thread is guaranteed to be right-angled (90°) - High productivity - Significant time savings compared to manual thread cutting - Quick-change chuck with integrated slip clutch - Includes large radius swivel arm - for easy positioning of the tap on the workpiece - High economic efficiency thanks to low investment and maintenance costs - For thread cutting in steel, stainless steel, aluminum and non-ferrous metals scope of delivery - Operation via touchscreen - Digital drilling depth display - Quick-chang ...

Offer 23395 Specifications: - max. working width 2540 mm - max. cutting capacity St 40 6.35 mm - Cutting angle adjustable mot. 0,5 - 2,5 ° - Cutting gap adjustment 0.05 - 0.8 mm - Number of hydraulic hold-downs 14 pcs -Mot. Backgauge with positioning control ELGO 10 - 1000 mm - Front angle stop 1000 mm - Stroke rate depending on cutting angle and cutting length 13 - 50 per/min - Hydraulic drive 400 V / 7.5 kW - Table height approx. 770 mm - Space requirements incl. back gauge, without front support arms -ca. W 3350 x H 1950 x D 2200 mm - Weight approx. 4700 kg - with: - Cutting depth adjustment - Cutting line illumination - E-foot switch

Clamping table, clamping angle, dividing head, dividing head, rotary table, milling machine table, clamping angle with three-jaw chuck, clamping angle with lathe chuck -Rotary table: with three-jaw chuck -Chuck size: Ø 160 mm -Spindle bore: Ø 42 mm -Dimension: 510/320/H220 mm -Weight: 50.9 kg

Clamping table, clamping angle, dividing head, dividing head, rotary table, milling machine table, clamping angle with three-jaw chuck, clamping angle with lathe chuck -Round table. with three-jaw chuck -Chuck size: Ø 210 mm -Spindle bore: Ø 64 mm -Center height: 150 mm -Dimension: 310/250/H260 mm -Weight: 47 kg

Clamping table, clamping angle, dividing head, dividing head, rotary table, milling machine table, clamping angle with three-jaw chuck, clamping angle with lathe chuck -Manufacturer: Schmid, rotary table with three-jaw chuck -Type: TWS200 -Chuck size: Ø 200 mm -Dimension: 250/250/H365 mm -Weight: 52 kg

Tool grinding machine, grinding machine, angle grinder, turning steel grinding machine, steel grinding machine -Elysier grinding possible with the machine -Diamond grinding wheel -1x angle tables: 220 x 310 mm -Angle adjustment: +15° bis -5° -Oscillation: 0-35 mm -Water cooling with: electrolytes -Sanding dust extraction -Max. Steels cross section: mm -Number: 1x grinding machines available -Price: per piece -Dimensions: 850/700/H1400 mm -Weight: 580 kg

Tool grinding machine, grinding machine, angle grinding machine, rotary steel grinding machine, steel grinding machine -Grinding places: 4 -Angle tables on swing tables: 3 -Angle table for chip breaker groove: 1 -Quantity: 1 piece available -Dimensions: 1210/1210/H1450 mm -Weight: 536kg

Rotary drive for air flaps, rotary air flap drive -Type: GCB136.1E -3-point, 5 Nm, 2 auxiliary switches -Maintenance-free, reversible synchronous motor -overload-proof through magnetic hysteresis coupling -robust and light plastic housing on steel base plate -Hand adjustment and position indicator -Built-in, freely adjustable pair of auxiliary switches Technical specifications: -Run time: 150 s at 50 Hz with a 90 degree angle of rotation -Nominal rotation angle: 90 degrees -Max. Rotation angle: 95 degrees -Operating voltage: 24 VAC -Power consumption: 2 VA -Auxiliary switch setting range 0...90 degrees -Housing protection class: IP 40 -Weight 0.8 kg

SAMAG MFZ 2-2 CNC milling machine was built in 2005 in Germany. This specially designed machine for the automatic machining of workpieces made of metallic materials has been equipped with two high-performance spindles and two work tables with a rotary axis, allowing for simultaneous machining of a part and loading/unloading of another. This solution maximises production efficiency and shortens production times, making the machine significantly distinguishable from other milling machines on the market. The machining, characterised by high quality and precision, is performed in automatic mode or in the setting up mode, using rotary tools taken from a capacious magazine. During its service life, the SAMAG twin-spindle milling machine has worked around 40000 hours and has been continuously serviced. The total weight of the machine is approximately 22 tonnes. Technical specifications of ...

Cylindrical Grinder GU32x60S Capacity Distance between centers 600 mm Swivel over table Ø320 mm Max. load of centers 100 kg Max. external grinding diameter Ø300 mm Wheel head Swivel angle ±30° Manual distance 160 mm Auto. rapid advance 40 mm Sliding seat supplementary displacement 95 (total 295) mm Min. setting unit (micro-adjust) 0.001 mm One turn of handwheel (graduation) 2 (0.005) mm Grinding wheel O.D. x width x I.D. Ø405 x 50 x Ø127 mm Speed (belt type) 1783 r.p.m. (50 Hz) / 1940 r.p.m. (60 Hz) Work spindle head Swivel angle 120° (+90°, -30°) Center taper MT. 4 Spindle speed (variable) 10~300 r.p.m. Max. load of spindle (tool holder includer) 35 kg (max. length : 150 mm) Tailstock Taper center MT. 4 Stroke 25 mm Table Swivel angle -2° ~ +10° Traverse speed 50 / 5400 mm/min Auto. reciprocate min. stroke 8 mm F ...

The column saw is designed to cut metals from aluminum and its castings, through non-ferrous metals, to high-quality metals such as stainless steel. The saw has a stable structure and reliable technology for automatic material feeding and cutting, which only takes place at an angle of 90°. The saw is also equipped with a cooling system, which is responsible for cooling, lubrication and protection against corrosion of tools and cut elements. The main materials cut on a frame saw are profiles, shafts, pipes, rods, angles, C-sections, T-sections and other shapes. Producer: KASTO Model HBA-360 AU Year of production 1995 Automatic operation type Tape cutting tool 5334x38x1.3 mm Max. dimensions of the cut material 360 x 360 mm Max. diameter of cut material 360 mm Angle cutting missing Arm feed speed 20 - 130 m/min Hydraulic vice pressing Engine power 7.5 kW Producer: KASTO Max. ...

: neu : ca. 8 Wochen ab Auftragse : Spanien : 34200 € : 694.26 € : 85 to : 500 mm : 5 : 40/15 bzw. 24x24 mm : 450x15 / 450x18 mm : 475 mm : 130x130x13 mm : 45/40 mm : 12 mm : 200x12 mm : 9,2 kW : 2300 mm : 1200 mm : 2100 mm : 2400 kg hydraulic drive 2 foot pedals for independant working on punching and section station bending unit with 2 dies, V40 and V70 flat steel stationWITH DEVICE FOR REDUCING DEFORMATION angle iron station with round and square bar cutting hydraulic downhold for flat- and angle station triangular notching station with table and gauge punching station with table and gauge gauge 1000 mm with contact switch, for angle / flat steel station operating manual in German and Englisch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Furniture roller, furniture dog plastic rollers, furniture transport trolley, transport roller, platform trolley, transport trolley, heavy duty trolley, table trolley, assembly trolley, chassis with 2 angle frames -Manufacturer: VARIOfit, chassis with 2 angle frames and VA top plate 5 mm -Type: sw-870.101 -Upper angle frame: removable with plate -Chassis: 2 swivel castors with brakes, 2 fixed castors -Load load: approx. 1200 kg -Dimension: 1250/855/H750 mm -Weight: 130 kg

The U2PRW mitre and drill is designed for processing slats and furniture fronts made of solid wood or MDF. The machine tool operates in a semi-automatic cycle. During one cycle, the machine performs: cutting at a given angle (in the range of 45 - 90 degrees) and drilling in a jammed plane or edge of the element. – made in Poland TECHNICAL PARAMETERS: Max. height of the material to be cut: 60 mm Max. width of the material to be cut at an angle of 45° 70 mm Max. material width at 90° 150 mm Max. length of cut material 2200 mm Min. length of cut material at 45° 455 mm main saw diameter 250 or 300 mm scoring diameter 100 mm Max. bottom cutter diameter 35 mm Max. bottom milling depth 15 mm seating diameter of face drills and bottom milling cutter 10 mm Drill head (face drilling): 4 spindles spindle axial spacing 32 ; 32 ; 40 mm Linear spindle system Max. face d ...

Suitable for automatic grinding of tooth faces and tooth backs on carbide-tipped circular saw blades., Accessories:, Total enclosure including coolant system,, Motorized setting of the rake and clearance angle,, Preselection of the direction of rotation of the grinding wheel and automatic change of direction of rotation,, Grinding speed and grinding path stepless adjustable,, Operating system modified Windows version,, Storage of approx. 4,000 programs possible,, Standard software package for tooth geometries according to the program overview,, Program for grinding saw blades with group teeth, with different tooth geometries,, Program for newly fitted and broken teeth,, Software package for multi-surface machining on the positive chip and flank face,, oscillating grinding on the face and top,, Automatic grinding wheel compensation,, Automatic central lubrication,, Feed pawl 2 mm,, 1 sawb ...