We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
122,050 used machines on RESALE, but how to find them? Machine Search
maximum number of results exceeded > 1000
please refine your search
used
Electro-hydraulic. Mandrel bending machine make TRANSFLUID type DB 628 ST SPSMasch. -No: 7507/2/2000 year 2000Technical specifications:Pipe diameter 6 - 30 mmMax. Wall thickness 2 mmSolid material up to 20 mmBending radius min. 10 mmBending angle up to 190 °Bending time at 90 ° 3.0 sec.Mandrel length / pipe pushing length 3000 mmRadius range max. 85 mmBending height 1050 mmfreestanding bending head 850 mm lg.Head for clear width between 2 bends of 300 mm distanceNominal pressure 250 barOperating pressure 200 barDrive power 2.2 kWDimensions L x W x H 3500 x 900 x 1300 mmWeight approx 800 kgWith- PLC control, bending process semi-automatic or manually selectable- Storage of 500 tubes with 20 different positions each- hydraulic drive, right-bending- Triggering optionally via foot or hand switch- Bending direction clockwise, hollow shaft for small radii- Tool reset by hand, hydraulic count ...
used
tube diameter: 6 - 28 mm wall strength: 2 mm bending radius min.: 2 x D Control: IPU 20 bending radius max.: 5,0 x D mm bending angle max.: 190 ° arbor length: 3000 mm operating pressure: 180 bar hydraulic motor: 4 kW weight of the machine ca.: 900 kg dimensions of the machine ca.: 3,8 x 1,1 x 1,3 m Condition: ready for operation: Electric 400 Volt: Bending segments: diverse Zoll Bending mandrels: 4 Operation panel: 0,5 x 0,6 x 1,03 m Double Foot pedal: Machine manual: Semi-automatic electro-hydr. mandrel tube bending machine with PLC control for 20 angles and display in the control panel for bending angle specification, angle detection and angle measurement via absolute value encoder, autom. tool plate reset, Turning device with digital display, hydr. quick chuck, aut. Mandrel lubrication, adjustable length stops. Operating modes: manual and semi-automatic. Control buttons: hydraul ...
used
Engine. Notching machine with adjustable angle (used) Manufacturer: COMACA Type Junior T 10 Knife length 210 mm x 210 mm Cutting capacity mild steel 4 mm Cutting capacity stainless steel 3 mm Strokes per minute 45 Table size 1280 x 650 mm Variable angle cutting device VARCUT 200 Cutting angle range from 30 degrees to 150 degrees Drive power 2.9 kW Weight approx. 450 kg Space requirements L 1280 m W 930 mm H 1500 mm 2 angle stops Foot switch Load capacity 10 tons Operating instructions The machine is in first-class condition and ready for immediate use. Forklifts available, freely loaded trucks Cheap shipping possible Location of the machine 48324 Sendenhorst for enquiries 0157-35496006 The price is net plus 19% VAT.
used
Clamping table, sinusoidal table, swivel table Swivel-clamping table Table length: 1130 mm Table width: 300 mm Table height: 112 mm Folding angle: 2 Folding angle: max. 7- folding angle 2 via threaded spindle folding angle max. 7 manually raised to stop Overall dimensions L x W x H: 1450 x 300 x 112 mm Weight: 275 kg good condition Ideal for making wedge strips; used
new
: neu : 2468C : prompt, Zwischenverkauf v : Deutschland : 2970 € : 2380 € : 1 : 195 kg (more tools, without exact illustration) CONSISTING OF: 1x accessories car (Delivery is galvanised) 4x angle stop 350 x 20 mm 4x adjustable angle stop 250 x 20 mm 15x Adjustment clamp 4x Multi-clamp 6x Stand angle, adjustable 175 x 20 mm 2x Stand angle, adjustable 225 x 21 mm 8x Stop rail 225 x 20 mm 10x Socket bolt 15x Plug holder 4x Ball Tension Bolt 4x Claw clamping bolt 28 x 100 mm 15x Spacer ring The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
PONAR KOWARY NUA 25 tool grinding machine was built by the Polish company PONAR KOWARY (LAKFAM) in 1984. A machine characterised by a robust construction of high stability, is used in tool shops and workshops for precision grinding of tools and tooling. Grinding of workpieces is performed on a table with a surface area (L x W) of 915 x 135 mm with two handwheels for manual longitudinal movement (X axis) and transverse movement (Z axis) of the work table. The reliable grinding wheel spindle moving at 3850 and 5635 rpm guarantees rapid and precise machining. The total weight of the machine is 910 kg. The machine is offered with the extensive range of equipment shown in the attached photos, which includes: – divider – angle vice 2 pcs. – moving tailstock: 2 pcs. – 3-jaw chuck fi 160 + spanner – workpiece centre positioning tool – fixed magnet – screw line tool – b ...
new
dimension of workpiece: 200 mm workpiece weight max.: 100 kg voltage: 230 V longitudinal feed: 150 mm vertical movement: 100 mm tool taper: bis 60 mm im Prisma Condition: new / unused: The machine can be viewed under current.: WMTR video measuring device T 210 Granite base plate 500 x 600 x 50 mm Digital size 0,001 mm resolution Longitudinal axis 150 mm Vertical axis 100 mm Tool holder in prism up to 80 mm diameter Swivel bracket 210 ° swiveling image comparison export of dates to EXCEL frequently measuring of video pictures labeling and marking of pictures saving and printing of pictures free calculation of variables detailed user administration superposition of DXF-drawings a lot of special software-modules Video measuring system IPM complete with: Software complete data acquisition create measurement protocols Consisting of: - Calculator, monitor, mouse, keyboard - ...
used
Suitable for fully automatic grinding of all known tooth geometries (e.g. flat, alternating, trapezoidal tooth) from HM – circular saw blades on the face and back in one clamping. The free programming also allows the Machining of special tooth shapes. Accesories: Pallet loader with 3 stations,, Coolant system with total enclosure,, Integrated hollow tooth grinding device,, Software package W 1 alternate tooth,, Software package W 2 flat tooth,, Software package W 3 flat/trapezoidal tooth (with tooth height difference),, Software package W 4 flat / roof tooth (with tooth height difference),, Software package W 5 trapezoidal tooth,, Software package W 6 pointed on one side,, Software package W 7 tooth face processing,,, Software package W 8 free programming of special tooth forms,, automatic tool positioning axis, Automatic D-axis for machining chip breaker grooves, auto. fire extinguish ...
new
thread dia.: M5 - M24 turning speeds: 70 - 200 U/min working area: max. 1200 R angle adjustable from - to: 0 - 90 Grad voltage: 230 V engine output: 1200 W weight: 65,0 kg - with micro spray system for constant cooling & minimal Cooling lubricant consumption - Includes blow-out device to remove chips, ensuring optimal visibility on the borehole - Includes quick-change chuck for using taps for Through and blind holes - Swivel motor unit for thread cutting at any desired angle between 0° and 90° - Higher accuracy compared to manual thread cutting, thread is guaranteed right angle (90°) - high productivity, significant time savings compared to manual Threading - Quick-change chuck with integrated slip clutch prevents breaking of the tap - Includes large radius swivel arm for easy positioning tap on the workpiece - For thread cutting in steel, stainless steel, aluminum and non-ferrous met ...
used
Angle polisher, angle buffing machine, angle grinder, angle drill -Power: 650 watts -Take: Ø 26 mm MK1 -Max. Width: 30mm -Dimensions: 570/240/H120 mm -Weight: 6 kg
used
VOLLMER CHD 250 – HM-tipped saw blade CNC sharpening machine The machine (fully equipped and very good condition) is currently in use and can be inspected and tested in our sharpening whorkshop. As new, it cost was 120.000 euro. We buyed the machine refurbishing from VOLLMER in 2010 I have, also, some new spar parts for CHD 250 for free: pusher guide shaft 1 pcs. 1394,7 euro = 1394,7 euro. flange for pusher guide schaft 2 pcs 84,7 euro = 169,4 euro Description Automatic grinding machine of hook and clearance surface for HM-tiped circular saw blades (face and top in one setting) Machining of hook and clearance surface, as well as tool body, in one single clamping. Fabrication year: 1996 . Programs for many tipes of tooth geometries (flat, alternate, trapezoidal tooth etc). Highly flexible machine with compact design. Enormously high productivity and short tooling t ...
used
plate thickness: 6.5 mm thickness at Niro-steel: 5.0 mm angle adjustable from - to: 30 - 140 Grad no. of strokes: ca. 50 Hub/min table:: 950 x 1030 mm blade length: 220 x 220 mm total power requirement: 4.0 kW weight: 800 kg range L-W-H: 1100 x 950 x 1280 mm current new price approx. 25.000 euros Special price on request Furnishing: - electro-hydraulic notching machine - Multi-functional machine with 2x workstations 1x notching, 1x bending station including bending tools - manual angle adjustment 30 - 140 degrees 2x handwheels for angle adjustment - large / stable work table - 2x angle stop, adjustable - automatic cutting gap adjustment - freely movable foot switch - Connection cable + 16A plug - Cutting performance: 6.0 mm to 60° ST 5.0 mm to 60° VA 4.0 mm to 30° ST 3.0 mm to 30° VA Machine link: http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=1008 -93970 ...
used
Suitable for automatic grinding of tooth face and tooth back on carbide-tipped circular saw blades in one clamping. All known tooth geometries (flat, alternate, trapezoidal teeth, etc.) can be ground automatically and in one pass., Accessories:, Total enclosure,, Coolant system,, Automatic loading system HS # 172 (workpiece weight up to 5 kg, stack height up to 180 mm),, Automatic set-up of the machine (automatic saw infeed axis, saw stop for diameter control, audio probe Measuring device for automatic probing, etc.),, Standard software package for tooth geometries after tooth shape summary,, Software for grinding saw blades with group teeth, with different tooth geometries,, Software for replaced and broken teeth,, Data entry station for the sawblade data, with touchpanel,, Device for internal coolant supply using oil,, Coolant collecting pan including grids for the machine,, Coolant co ...
used
Description: Cold bending: flat steel 100 x 5 mm square steel 16 x 16 mm Round steel 18 mm angle steel 60 x 8 mm - Hot bending: flat steel 100 x 15 mm square steel 30 x 30 mm round steel 30 mm angle steel 100 x 12 mm Fitted with eccentric quick clamping device readable bending angle up to 120 degrees angle stop lever and bending jigs material stop delivered in original packaging unused ! Approx. Onsite Dimension. (l x w x h): 300 x 220 x 250 mm, weight approx.: 35 kg
used
Description: Top-maintained VENJAKOB Venspray coating systems with steel belt transport, 2 spray systems, IR dryer, airless pumps, smoothing roller, HILMER & KOCH hydraulic press and transport rollers. The system has a working width of approx. 1,600 mm and a Siemens Simatic HMI Touch Panel control. Only samples, tests and product developments were processed on the system. , Pos. 1 VENJAKOB roller conveyor angle transfer, manual removal station Pos. 2 VENJAKOB accumulation roller transport and control station Pos. 3 VENJAKOB IR preheating zone VEN DRY IR top/bottom Pos. 4 VENJAKOB spraying machine VENSPRAY with airless pump station Pos. 5 VENJAKOB IR dry zone VEN DRY IR above Pos. 6 VENJAKOB spraying machine VENSPRAY with airless pump station Pos. 7 VENJAKOB IR drying zone VEN DRY IR at the top and steel strip cleaning station Pos. 8 VENJAKOB angle transfer Pos. 9 VENJAKOB l ...
used
Agitator 0.37 KW, 400V, 1340 RPM Coupling aluminium Agitator shaft d = 14 mm, L = 500 mm, stainless steel 1.4301 Stirrer stainless steel, with angle-adjustable angle leaves, d = 244 mm, angle blade width 50 mm, stainless steel 1.4301
used
Manufacturer: Weinbrenner Type: TSV 6 / 3050 Year of constr.: End of 2015 demonstration machine Cutting length: 3050 mm Cutting capacity: 6 mm (steel) Hours of operation: 54 Control: Cybelec DNC 60 Dimensions L/W/H: 4100/2050/2100 mm Table height: 1000 mm Weight: 8500 kg Min. cutting angle: 1° Cutting angle max.: 2.5 ° Stroke rate minimum: 20 min. Max speed: 25 min. Cutting gap adjustment: motorized Cutting angle adjustment: hydraulic Number of holders: 14 Rear velocity range: 1000 mm Security: setting the photocell safety on the front and back Oil filling: 225 l Electrical power: 15 KW Power consumption: 3 x 400 V / 50 Hz Back-up fuse: 50 A Additional equipment: Extension of the side stop on 2050 mm Side stop side swing-away A total of 8 support arms freely movable along the entire length of the table The machine is a demonstration machine in mint cond ...
used
Built-in screwdriver with control, BL57/50 MDW, 457010, Pico/mA, DSM, used Top Attention special price! (For your info - current new price for this screwdriver and control € 9.500 excl. VAT) We have set the lowest price on the market for a comparable used part. We still have several identical and other such units, but the quantity is ending. If you buy more than 1 piece you will get a great discount. If you have a UID number we will gladly issue an invoice without VAT. Used - Top condition The part was bought from a company in the course of a machine dismantling and is in very good condition. Technical data: Screwdriver BL57/50 MDW, DSM 457010, max. 50Nm, incl. all cable sets. This high quality DSM screwdriver is designed for direct measurement of torque and angle of rotation. The high-precision transducers required for this are installed directly on the output. The meas ...
used
Two-coordinate measuring instruments ZKM Applications: External measurements - Internal measurements - Bore distance measurements with double image eyepiece Shape tests with reable inserts Angle measurements with angle measurement slot and optical rotary table (2") Male thread measurements Equipment: Spitzenbock - Angle measuring device to the tip trestle (5") - adjustable V-bearing opt.-mechanical probe (measuring lever attachment) - adjustable plant table - incident light illumination Projection device - Rotary table with partial circle Increased optical touch accuracy through the use of inteference lines ZKM 01-150 Measuring range x - 150 mm Measuring range y - 100 mm Scale value 0.1 mm ZKM 01-250 Measuring range x - 250 mm Measuring range y - 100 mm Scale value 0.1 mm possible versions: ...
used
Two-coordinate measuring instruments ZKM Applications: External measurements - Internal measurements - Bore distance measurements with double image eyepiece Shape tests with reable inserts Angle measurements with angle measurement slot and optical rotary table (2") Male thread measurements Equipment: Spitzenbock - Angle measuring device to the tip trestle (5") - adjustable V-bearing opt.-mechanical probe (measuring lever attachment) - adjustable plant table - incident light illumination Projection device - Rotary table with partial circle Increased optical touch accuracy through the use of inteference lines ZKM 01-150 Measuring range x - 150 mm Measuring range y - 100 mm Scale value 0.1 mm ZKM 01-250 Measuring range x - 250 mm Measuring range y - 100 mm Scale value 0.1 mm possible versions: ...
used
Sparkling Pressure Tank / Sparkling Cooling Tank / Steel Pressure Tank Agitator Tank / Storage Tank / Pressure Tank with red food safe munkadur coating with cooling jacket and with isolation STANDING with new KIESELMANN sparkling pressure fitting Operating Pressure: 8 bar Volume: 5.750 Litre Measurement and Weight: Total Height: 4400 mm Tank Body Height: 3325 mm Diameter: 1600 mm Weight: 2110 kg Uni 3750 Operating-overpressure: 8 bar, Test pressure: 10,5 bar Operating pressure cooling jacket: 2 bar, Test pressure: 2,6 bar Inspection book, Dokumentation available Tank-Description Container with torispherical bottoms. Jacket and walls 9 mm. On cylindrical part of a cooling jacket as double jacket about 2.500 mm high. Container outside approx. 100 mm isolated, with screw stainless steel metal cover. Tank upp ...
used
Technical data: - Bending capacity - steel pipe of 20 - 60 x 4 mm - - stainless steel pipe of 20 - 50 x 3 mm - max. resistance moment 6.2 cm - max bending angle 180° - max radius 125 mm - Bending speed 8 sec - Drive 400 V / 3 kW - Space requirement approx. L 2400 x H 1600 x D 1000 mm - Weight approx. 1400 kg - with: - Bending angle control via potentiometer with digital display - 6-fold bending angle preselection - Indoor + external pipe deburrer - Bending tools Rx2.5D x 38 ; • 50 , 65 ;
used
This electrically driven sinusoidal table has an incremental angle measuring device (Heidenhain RON 705). -Sinusoidal table for workpiece clamping -Swivel range 0 - 110° -Clamping surface 800 x 600 mm -Groove width 22 mm -Groove spacing 100 mm -Number of grooves:6 pieces -Dimensions: Length: 840 mm Width: 760 mm Height: 220 mm Clamping angle, clamping angle, clamping tower, clamping device, About us: MBM Maschinenservice & Gebrauchtmaschinen GmbH, is a freelance specialist for SHW machine tools. Our main task is in the field of machine tool milling machines. Our services include spare parts deliveries, on-site customer service, machine overhauls and control modernizations. Performances: - Used machines - Spare parts - Customer service - Machine service - Machine overhauls - Control modernization
used
x-travel: 6200 mm y-travel: 3200 mm z-travel: 1000 mm Control: Heidenhain iTNC 530 total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: 12,7 x 11,0 x 6,0 m Retrofit: 2009 CNC control Heidenhain iTNC 530 The angle milling head is adjusted via the NC program automatically. In this case, the head is treated as a C axis and represents the angles accordingly (to the degree) fully automatically. X-axis (longitudinal adjustment of the table) Lubrication: Hydrostatic lubrication Travel distance: 6200 mm Maximum feed speed: 15 m / min Direct distance measuring system from Heidenhain Y-axis (transverse adjustment of the milling support) Lubrication: Hydrostatic lubrication Travel distance: 3200 mm Maximum feed speed: 15 m / min Direct distance measuring system from Heidenhain Z-axis (vertical adjustment of the milling spindle slide) Travel distance: 1000 mm Maxim ...
used
max. wheel diameter: 400 mm gear width: 0 mm module: pinion diameter - max.: 254 mm axial cross angle: 90 ° total power requirement: 15 kW weight of the machine ca.: t dimensions of the machine ca.: m This machine is very suitable for precision production testing of spiral and hypoid bevel gears with shaft angle 90°. The gear spindle is vertical and the pinion spindle is horizontal. The pinion cone distance can be adjusted while the machine is working in order to find the optimal mounting position whereby the gear is loaded with a preset torque. The axial pinion position can be adjusted until the quietest meshing position of the traction flank is found. Likewise, the thrust flank can be tested during the return run. Marking compound is sprayed on both sides of the teeth so the flank contact pattern can be seen. Working cycles, as well as the positioning in the tooth gap, are automat ...
used
tube diameter max.: 38 mm wall strength: 2 mm bar material dia. min.: 10 mm bending radius min.: 35 mm bending radius max.: 150 mm pull up length of tube: 4500 mm bending angle max.: 180 ° accuracy of bending angle: ± 0,2 ° total power requirement: 7,5 kW weight of the machine ca.: 1,2 t - with 8-pos. bending angle pre-selection - crawler gear control - positioning device by hand - tube twist device Following bending tools are with the machine: - ø 10 mm, radius 27,5 mm - ø 12 mm, radius 35 mm - ø 12 mm, radius 56 mm - ø 15 mm, radius 35 mm - ø 15 mm, radius 57,5 mm - ø 18 mm, radius 35 mm - ø 18 mm, radius 59 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
max. wheel diameter: 1600 mm gear width: 250 mm max. module: 20 min. module: 1,5 base circle dia. - max.: 1450 mm base circle dia. - min.: 150 mm specimen weight from/to: 4000 kg feeler adjustment movement - parallel: 1400 mm max.helical angle: 0 - 90 ° wheel diameter with counterstay: 1000 mm feeler adjustment movement - parallel: 800 mm centre height: 1150 mm electrics - voltage/frequency: 400 / 50 V/Hz dimensions of the machine ca.: 2,8 x 2,4 x 2,3 m total power requirement: 2 kW weight of the machine ca.: 3 t Universal Involute and Helix Testing Machine - modernized 1995 Machine is suitable for measuring all individual tooth data on straight and helical spur gears, and shaping and shaving cutters. Following tooth data can be tested: Tooth flanks, Involute base circle dia. and pressure angle, Profile c ...
used
Capacity round maximum diameter: 410 mm Angle degrees maximum: 0 Capacity square: 0 mm Workpiece height: 0 mm Workpiece width: 0 mm Capacity rectangle: 0 mm MACH-id 5332 MAKE MEBA Germany TYPE 410 DG YOP 2013 SPECIFICATIONS Bandsaw / Circelblade / Automat Semi Automat Angle L / R Degrees L / R Degree Cutting capacity 90 ˚ Ø 410 mm Cuttting capacity 90 ˚ Flatt 700 x 410 mm Cutting capacity 45˚ Ø 410 mm Cuttting capacity 45 ˚ Flatt 500 x 410 mm blade dimensions 5800 x 41 x 1,3 mm roller conveyor / push up / measuring 3000 mm Cutti ...
new
grinding range: max. 30 mm angle adjustable from - to: horizontal 0-180 Grad angle adjustable from - to: vertikal 0-45 Grad angle adjustable from - to: negativ 0-52 Grad connected load: 230 V wheel diameter: 100 mm weight of the machine ca.: 55 Kg dimensions: 0,5 x 0,4 x 0,4 m This grinding machine is suitable for: Twist drill (max.13mm), milling cutter and turning tool (max. 30mm) comes with: - chisel grinding tool - Diamond grinding stone for HM. - White whetstone for HSS. - LED lighting - All adjustment tools. - Diamond dresser for sharpening stones. C-5 collet set with the following sizes. 1.5 - 2 - 3 - 4 - 5 - 6 - 7 - 8 -9 -10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 20 - 21 - 22 - 23 - 24 - 25 - 26 - 27 - 28 - 29 - 30 mm. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
number: 96 Positionen weight: 600 kg condition: neu : 28 mm Special set 96 pieces, 28mm system, consisting of: 1x tool trolley 30x quick release bolts with twist lock short, without O-rings 8x universal stop 150 L - nitrided 4x universal stop 225 L - nitrided 8x stop and clamping angle 175 L - cast 2x stop and clamping angle 500 G left - nitrided 1x stop and clamping bracket 750 G left - nitrided 1x stop and clamping bracket 750 G right - nitrided 1x stop and clamping bracket 500 G left - nitrided 1x stop and clamping bracket 500 G right - nitrided 4x stop and clamping angle 300 G left - nitrided 8x prism Ø60-135 ° burnished - with collar complete with screw collar and countersunk head 16x professional screw clamps - nitrided 6x Professional screw clamp 45 ° / 90 ° - nitrided 4x universal stop 300 - nitrided 1x accessory set consisting of: Eccentric, Allen key, brush, sharpening ston ...
new
grinding range: 8 - 32 mm sharp cornered angle min./max.: 90 - 140 Grad connected load: 230 V weight of the machine ca.: 16 Kg dimensions of the machine ca.: 0,43 x 0,24 x 0,24 m Drill grinding machine: Additional station for grinding back the drilling cutting surface (clearance angle) 25tk. Collets ER 40 are included in the scope of delivery, these are also suitable for clamping intermediate sizes. For grinding twist drills made of HSS and Hard metals with a TiN layer of 8 - 32 mm. Rotor with precision ball bearings guarantees smooth running. Vibration-free running thanks to its heavy weight and rubber feet. Sharpening angle adjustable for all common twist drills. Package dimensions: 430 x 240 x 240mm. Weight 16kg. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
number: 57 Positionen weight: 98 kg condition: neu : 28 mm Set 2: 57 pieces, 28mm system, consisting of: Clamps: 6 x 280610.N Clamps: 4 x 280630.N Prism: 4 x 280648.1.N Bolt: 18 x 160511 Magnetic bolt 4 x 280740 Stop: 6 x 280410.N Stop: 6 x 280420.N Angle: 4 x 160110.N Angle: 2 x 280152.N Angle: 2 x 280162.N Accessory set. 1 x 283999 Price plus packaging and transport. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Capacity round maximum diameter: 335 mm Angle degrees maximum: 0 Capacity square: 0 mm Workpiece height: 0 mm Workpiece width: 0 mm Capacity rectangle: 0 mm MACH-id 3721 MAKE MEBA TYPE 335 DGA 1000 YEAR 2001 SPECIFICATIONS Bandsaw / Circelblade / Automat Bandsaw Mitre Cutting Angle L / R Degrees Angle cutting L / R 45 / 30 Gr. Cutting capacity 90 ˚ Ø 335 mm Cuttting capacity 90 ˚ Flatt 500 x 335 mm Cutting capacity 45˚ Ø 330 mm Cuttting capacity 45 ˚ Flatt 320 x 335 mm blade dimensions 4400 x 34 x 1,1 mm roller conveyor / push up / measuring Push upCutting speed M/min 18 - 115 M/min DIMENSIONS Length ...
new
number: 55 Positionen : 16 mm condition: neu weight: 23 kg Set 2 55 pieces, 16mm system, consisting of: Clamps: 6 x 160610 Clamps: 2 x 160630 Prism: 4 x 160645.1.N Bolt: 18 x 160511 Stop: 4 x 160410.N Stop: 6 x 160420.N Angle: 6 x 160108.N Angle: 6 x 160110.N Angle: 2 x 160162.N Accessory set. 1 x 163999 Price plus packaging and transport. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
table length: unterschiedlich mm table width: unterschiedlich mm table height (lateral area): unterschiedlich mm weight: ca. 240 kg Description : - Special set for SIEGMUND 28 clamping tables included : - 1x tool trolley - 30x quick release bolts with twist lock short - 8x universal stoppers 150 L - nitrided - 4x universal stop 225 L - nitrided - 8x stop and clamping angle 175 L - cast - 2x stop and clamping angle 500 G left - nitrided - 1x stop and clamping bracket 750 G left - nitrided - 1x stop and clamping bracket 750 G right - nitrided - 1x stop and clamping bracket 500 G left - nitrided - 1x stop and clamping bracket 500 G right - nitrided - 4x stop and clamping angle 300 G left - nitrided - 8x prism Ø60-135 ° burnished - 16x Professional screw clamps - nitrided - 6x Professional screw clamp 45 ° / 90 ° - nitrided - 4x universal stop 300 - nitrided - 1x accessory set consisting ...
new
sheet width: 3100 mm plate thickness: 6,0 mm distance between columns: 3.100 mm down holder: 14 Stück no. of strokes: 16 - 24 Hub/min oil volume: 150 ltr. cutting angle: 0,5 - 1,5 ° thickness at Niro-steel: 4,0 mm column arm: 350 mm engine output: 11,0 kW weight of the machine ca.: 7.060 kg range L-W-H: 4100 x 2200 x 2190 mm -------------------------------------------------- electr. / hydraulic CNC guillotine shears - guided by a backdrop with CYBELEC CNC touch screen control with electr. / hydr. Cutting gap and cutting angle adjustment -------------------------------------------------- Furnishing: - CNC guiding guillotine shears - with electr. / hydr. Cutting gap and cutting angle adjustment - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including s ...
new
tube diameter: 2 x 3,91 mm ST tube diameter: 60 x 4,5 mm GAS revolutions per minute: 2,5 U/min radius: min. 2 x D mm bar material - diameter: 35,0 mm total power requirement: 1,5 kW weight: 130 kg Furnishing: - mandrelless tube bending machine - mechan. Angle adjustment via dial - Tool holder: hexagonal 40 mm + 50 mm - Bending angle: 0 ° to 180 ° (max. 210 ° angle of rotation) - Bending radius: R10 to R270 mm - integrated chassis Bending segments on request The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Hydraulic notching machine make BOSCHERT type K 30-180 / CNCYear of construction 1989for latches of all angles from 30 ° to 180 °Cutting capacity steel ST 40: 4 mmCutting capacity stainless steel: 3 mmKnife length: 200 mmCutting length: 200 x 200 mmCutting angle adjustable: 30 - 180 °Table height: 900 mmelectrical connection value: 8 KVAHydraulic oil filling: 30 litersExternal dimensions L x W x H: 1500 x 1000 x 1930 mmWeight: 1950 kgwithout stoppersWith- Control PC 2000 for setting the cutting angle- automatic execution of the entered programs- high travel speed from one angle to another- ideal view on knife tip- easy to catch on crack- ideal for catching beveled sheets- Latches of different angles on a sheet without clipboard- Pawls from aluminum to stainless steel with the same knives- Footswitchused, in good conditionPrice on request.Delivery: ex warehouse or location free loading ...
used
Hydraulic fixed angle notching machine make KNUTH type KKM 250.6Machine -No: 124780 built in 2002Technical specifications:max.sheet thickness at 45 kg: 6.0 mmCutting length: 250 mmCutting angle: 90 degreesStrokes per minute: 50Table size: 810 x 750 mmHydraulic oil tank: 40 lDrive power: 4.0 kWExternal dimensions approx .: 900 x 900 x 1150 mmWeight approx: 856 kgWith- foot switch- 2 adjustable angle lengthsused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools
new
cutting diameter: 300 mm saw band length: 3150 x 27 x 0,9 mm cutting width: 375 mm band speed: 15 - 90 m/min : 375 x 190 mm cutting capacity - round: 300 bei 90° mm : 240 x 160 mm cutting capacity - round: 240 bei 45° mm work height max.: 910 mm total power requirement: 2,2 kW weight of the machine ca.: 420 kg dimensions of the machine ca.: 2180 x 1660 x 2030 mm Continuous adjustment of the cutting angle within the range 90°–60° when the workpiece is clamped tight. Very robust machine framework composes of castings from grey cast iron and ensures vibration absorption. Modern concept of the band saw arm allows for large cutting ranges in upright and angular cuts. Simple locking and adjusting of the desired cutting angle on the angle scale. Massive quick-clamping vice ensures easy and reliable mate-rial clamping. Large diameter running wheels and precise three-side hardmetal guiding ...
used
Hydr. CNC-Sheet metal Shear make GWF MENGELE type S 8 - 1500Machine -No: S2544, built in 1989Max. Cutting length: 1550 mmMax. Sheet thickness: 8 mmlateral. Discharge i. Stand: 50 mmSheet metal passage: 16 mmCutting angle adjustable: 2 ° 30 - 0,5 °Empty strokes: 25 - 32Number of hold-downs: 8Cutting pressure: 280 barHold-down pressure: 80 barOil filling: 300 lDrive power: 18.5 kWTotal connected load: 20.1 kWExternal dimensions: 2130 x 3260 x 2360 mmWeight: 5.8 tWith- CNC control SIEMENS S 5 for numerical sheet bending- Holding device mot- Sheet metal removal with conveyor belt- Cutting gap and cutting angle m. Control programmable- Spare knife- Schermesser for 750 kg strength- Separate hold-down z. Cutting after crack- Hold-down pressure adjustable and readable from the front- 2 rocker stops- Finger guard with recessed grip- balls in the support table- Angle stop m. Norius- Footswitchus ...
new
sheet width: 2065 mm plate thickness: 1,20 mm daylight opening: mit WZ 35,0 mm daylight opening: ohne WZ 60,0 mm bending angle max.: 0 - 135 ° total power requirement: manuell weight of the machine ca.: 520 kg. dimensions of the machine ca.: 2400 x 1115 x 1150 mm - Segmented upper beam for a large number of bending options - Universally applicable bending machine for plumbing and repair shops - High upper beam for producing high-edged profiles - Quick and easy bending process using a bow handle - Easy adjustment of the upper beam for efficient work - The bending angle is set using a scale - Individually removable segments for bending boxes - Robust construction in a modern design Furnishing : - segmented upper beam - Foot clamp - Fixed stop for angle adjustment The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Hydr. Sheet Metal Shear Make MENGELE Type S 4 - 5000/3Machine -No: S 2237 5000/3 Year 1976Cutting length: 5050 mmMax. Sheet thickness: 3.0 mmlateral. Discharge: 300 mmCutting angle: 0.6 °Strokes per minute: 34Number of hold-downs: 22mot. backgauge: 0 - 1000 mmlateral. Angle stop: 2000 mmOperating pressure: 230 barHold-down pressure: 58 barOil filling: 200 lDrive power: 11 kWOutside dimensions approx: 5750 x 2500 x 1700 mmWeight approx: 15 tWith- mot. backgauge- Angle stop front- Footswitchused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools
used
Hydr. Sheat metal Shear make EHT type EHS 6-50Machine -No: 19782 Year 1983Max. Sheet thickness: 6.0 mmCutting length: 5050 mmKnife length: 5100 mmCutting angle: 1 - 15 °Knife strokes per minute: 18Number of hold-downs: 26Pressure p. Hold down: 60 barOperating pressure: 280 barOil filling: 220 lDrive power: 12 kWWeight approx: 11 tOutside dimensions approx: 5500 x 2900 x 2100 mmWith- mot. back gauge 1500 mm with length indicator- Cutting angle indicator- Cutting angle adjustment- Cutting length limit- Footswitchused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools
used
Specifications: - working width 2540 mm - max. cutting capacity St 40 4 mm - mot. Cutting angle adjustment - Cut gap. by scaled adjustment screws - Number of hydraulic holders 14 pcs - Mot. backgauge with positioning. 10 - 1000 mm - Stroke rate depending on cutting angle and cutting length 23 per min - Hydraulic drive 400 V / 7.5 kW - Table height 1030 mm - Space requirement approx. W 2500 x H 1630 x D 2150 mm - Weight approx. 3600 kg - with: - Sheet metal holding pneum. supported - front angle stop + support arms - Electronic cutting depth adjustment - Cut line lighting - E-foot switch
used
ERMAK CNC HVR 3100 x 13 hydraulic guillotine shears built in Turkey in 2008, are designed for cutting workpieces made of among others mild steel or stainless steel. The metal sheet with a maximum length of 3100 mm and a maximum thickness of 8 mm (plain steel) or 13 mm (stainless steel), is held during machining by 14 hydraulic clamps. The angle of the cutting blade can be freely adjusted in the range from 0.5° to 2.0°. Full control over the operation of the CNC HVR 3113 machine is guaranteed by the control panel located on the guillotine shears body with installed CYBELEC DNC 60 CNC controller, allowing programming of many different machining processes. The guillotine shears is equipped with among others new cutting blades and a foot control pedal, making the operator’s work much more comfortable and simple. The total weight of the machine is 13400 kg. The total weight of the mach ...
used
For sale complete plant for wood pellet production, made from CPM, capacity 6t/h. A most of the maschines from line are produced in between 2008-2010.y., except presses for making pellets (its bit older then rest of the line, but completly renewed before restarting. Line is consisting from: 1.Chain conveyer for logs transport. 2.Lift with angle platform for dosing material. 3.Entrance belt transporter with magnetic section for detection of iron. 4.Grinder (hammer mill) BRUKS 500kW 5.Verticaly basket transporter for chip wood. 6.Horisontal belt transporter for chip wood with three side ejectors into depoos (separated with type of the wood) 7.Hidraulic floor platform for dosing wood chips (three pcs.) with all instalation and system of hidraulic pistons. 8.Horisontal belt transporter for transportation material on drying. 9.Repler transporter for driving wood chips into fire plac ...
used
pressure: 80,0 / 110 t punching cross-cut in cmm: 27,0 in 20 mm L-beam: 120 x 13 mm L-beam: T 120 x 12 mm shear: flat material: 500x18 / 400x19 mm throat: 510 mm work height max.: 1050 mm total power requirement: 6,5 kW weight: 1650 kg range L-W-H: 1750 x 850 x 1850 mm very good condition () Furnishing: - hydraulic, combined profile steel shears with release station with punching station .. punching capacity 800kN Flat steel shears .. Shear capacity 100kN Angle steel scissors Angle steel knife for cutting 90 ° & 45 ° miters Cutting angle steel + T-steel + I-steel - Support table at the notching station - Scraper at the punching station - Freely movable foot switch - Central lubrication - Safety devices - Operating instructions (PDF) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
-Exhibition Machine- State-of-the-art fully hydraulic folding machine. Extensive standard equipment: · hydraulic drive for upper and bending beam · Pointed rail 45 degrees · Rails in upper, lower and bending beam · Oil filling · Control panel with: Digital display of bending angle infinitely variable specification of the bending angle Push button for controlling the upper and bending beam Switch for automatic operation · Control: PLC - Siemens · Foot switch for manual and automatic operation · CE certification · Safety stop at approx. 25 mm upper beam height Hydraulic dynamic crowning Motorized backgauge (1000 mm) Electr./hydr. adjustment of the bending wing, Touch screen: Input for backgauge values and Bending angle of the folding machine Pressure regulation of the upper beam Automatic tool clamping Round bending function with bending Half-shells 180 ...
used
Vollmer CHHF 21 H - Machine for single-sided grinding Year of construction: 1989 S/N 907 Make: Vollmer Germany in good working condition The technical data of the CHHF 21H at a glance: Circular saw blades Outer diameter 80 to 700 mm Bore diameter 20 to 105 mm Tooth pitch from 8 mm Hook angle up to 30° Radial clearance angle -7° to +3° Tangential clearance angle up to 5° Connected load approx. 0.52 kW Weight approx. 85 kg Dimensions: 70 x 50 x 80 cm Cisei8tfrg This machine has been specially designed for the repair of lack of carbide teeth. Newly inserted tips are used in the existing teeth. With this tabletop version, VOLLMER offers a a particularly economical, space-saving solution. The CHHF 21 H works according to the wet grinding process. During the grinding process, the grinding unit manually moved over the tooth flanks, with the saw blade Saw blade ...