ammonia compressor used for sale

Rated power: 75kW, max. operating overpressure: 8.5bar, speed: 3000rpm, operating hours: 75122h, load hours: 72719h. The machine requires bearing replacement. Documentation available. An on-site inspection is possible.

Air compressors from Kostal Industrie Elektrik

4000 werkuren! Diesel-oil (1) -- Naphte (2) -- Electr (3): electric voltage: 3 x 380V - 50Hz Low press. (1) High press (2) Screw (3): 12.75 bar screw compressor Volume flow rate: 18.3 m3/min Power imput: 90kW Volume (L): 1500 L

Operating pressure: 13bar, volume flow: 17.07m³/min, motor power: 90kW, motor speed: 3480rpm, weight: approx. 1750kg. The frequency converter of the machine is defective. An on-site inspection is possible.

Two compressors Kaeser are available. 1) Kaeser CSD 102 T SFC, year of manufacture: 2002, rated power: 55kW, max. operating pressure: 8.5bar, refrigerant: R134a, refrigerant quantity: 3.1kg, operating hours: approx. 132150h, load hours: approx. 129858h. 2) Kaeser BS 61, year of manufacture: 2001, rated power: 31kW, max. operating pressure: 8bar, operating hours: 91889h, load hours: 78711h. Documentation available. An on-site inspection is possible.

Two identical Blitz compressors are available. Motor power: 22kW, max. operating pressure: 10bar, flow rate: 3m³/min, weight: approx. 500kg. Documentation available. An on-site inspection is possible.

power capacity: 7,5 kW feed pressure: 10 bar volume capacity: 815 dm³ /min total power requirement: 7,5 kW weight of the machine ca.: 0,4 kg Alup piston compressor - Tank 350 liters - Soundproof housing (68 dB(A) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Compressor system / compressed air system composed of: Compressor Type STA-010 Maximum pressure 10 bar Output 0.9m³ per min incl. pressure tank 350l (14BAR) with filter

feed pressure: 10 bar liter capacity: 2,71 m³ / min motor speeds:: 3000 U/min dimensions: 1300 x 1000 x 1900 mm total power requirement: 18,5 kW weight of the machine ca.: 500 kg Features: - Focus Control 2.0 control system - Network pressure sensor - Belt-driven drive system - Soundproofed The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Air Pressure: 40 bar // Delivery Rate: 1630 m³/h

Air Pressure: 40 bar // Delivery Rate: 950 m³/h

An Atlas Copco piston compressor is available. Motor power: 4kW, max. operating pressure: 11bar, intake capacity: approx. 633l/min, delivery rate at 7bar: approx. 412l/min, speed: 1000rpm, tank capacity: 270l. Machine dimensions: approx. 1500mm/500mm/1200mm, weight: approx. 125kg. Documentation available. On-site inspection possible.

output: 30 kW suction power: 4.200 l/min turning speeds: 5.092 U/min overpressure: 10 bar dimensions of machine L x W x H: 1,72 x 0,90 x 1,60 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

A mobile diesel screw compressor unit CompAir, suitable for construction site use, is available. Volume flow: 20m³/min, max. operating pressure: 24bar, motor power: 224kW, engine: Cummins QSB6.7, chassis: height-adjustable, fuel tank capacity: 350l. Machine dimensions: approx. 5500mm/2000mm/2700mm, weight: approx. 3500kg. Documentation available. An on-site inspection is possible.

Final compression pressure: 10 pe/bar Speed: 745 1/min Volume flow: 3455 dm³/min Motor power: 22 kW

A mobile high-performance construction site compressor Atlas Copco for drilling applications is available. Design: tandem, volume flow: 28m³/min, max. operating pressure: 25bar, motor power: 368kW, engine: Scania DC13, fuel tank capacity: 600l, fuel consumption per hour at 75% and 100% load: 55l/77l. Machine dimensions X/Y/Z: approx. 6000mm/2100mm/2500mm, weight: approx. 7400kg, operating hours: approx. 650h. Including aftercooler, water separator, and PF filter. Documentation available. On-site inspection possible.

Brand: Atlas Compo Type: GX5C FF with integrated refrigeration dryer Kind: Screw compressor Serial number: AII642955 Chassis number: 8152101195 Year of construction: 2004 Cooling: Air-cooled Weight: 198kg. Assets: 5.5 kW Sound level: 64 dBA Work pressure: 10 Bar Compressed air: Capacity Approx. 10.0- 10.1 liters/second Length mm: 145cm Width mm: 55cm Height mm: 130cm State machine: Very good Electrical connection: 3 phase Missing parts: No Photos/film available: Photos available 10.2.192

Brand: Boge Type: C3LR Kind: Screw compressor, air-cooled Max. final pressure: 10 bar Chassis number: 5063340 Year of construction: 2013 Capacity: 0.24 m3/min. = 8.3 CFM Engine speed: 1,500/ min. Drive power: 2.2 kW (3 hp) Pressure vessel: 90 liter Voltage: 400V / 50Hz (3-phase) L x W x H: 1185 x 550 x 1010 Noise level: 61 dB (A) Weight: Approx. 130 kg Residual oil content: < 3 mg/m³ Connection: G ½” (ball valve) Cooling air volume: 600 m³/h Ambient temperature range: +5 to +40 °C Photos/film available: Photos available 10.2.195

Brand: Ingersoll Rand Type: 2339531 Kind: Compressor with Refrigerant Dryer Year of construction: 2011 Operating hours/meters: 6107 Weight: 188 + 27 kg Assets: 3 kW/ 4 HP Air pressure: 14 bar Electrical connection: 400/230V, Photos/film available: Photos available 10.2.197

Operating pressure: 10bar, max. temperature: 40°C, cooling medium: R134A, quantity: approx. 500g, weight: approx. 450kg. An on site inspection is possible.

Used Spanish compressor made by ABC, type: 4HA-4-LT, new 1997, capacity 7.8 m3 / min. Dimensions: 2100 x 4000 x 2500 mm. The compressor consists of: cooler AIRSEC AW-750010/10, new 1997, capacity 7.5 m3/h, cold dryer AIRSEC FD10B/E new1997, capacity 300 m3/h

feed pressure: 8,5 bar liter capacity: . l total power requirement: 454 kW weight of the machine ca.: t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Stationary screw compressor with refrigeration dryer on 500 l container Specifications: Pressure 10 bar Volume flow 2000 l/min Voltage 400 V Drive power 15 kW Beh.-Vol. 500 l Weight 499 kg Noise 65 dB(A) Air outlet 3/4"i Dimensions (WxDxH) 1960x740x1725 mm Hint: ! without TÜV approval, container papers are not available

ALMIG Combi 15-10 rotary screw air compressor YOM 2012. Never used. Motor speed 3000 rpm Motor power 15 kW Volume flow m3/min- 1.84 Volume m3/hour- 110 Max. pressure 10 Bar. Air Receiver Capacity 500L

Dimensions (L/W/H): 1950x690x1700 mm Weight: 431 kg Total power requirement: 7,5 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 1950x690x1700 mm Weight: 426 kg Total power requirement: 5,5 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Air consumption: 120 m³/h Pressure power: 10 bar power requirement: 15 kW Packing: ca. 1,20,81,4 m Shipping weight: 300 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

A screw compressor is offered. Maximum pressure 10bar, volume flow approx. 2020l/min (2.02m3/min) with separate compressed air tank, galvanized. Viewing possible by appointment.

Motor power: 45 kW Nominal flow rate: 7.5 m³/min Maximum working pressure: 10 bar Voltage/Phase: 380V Electrical protection: IP55 Management: Integrated inverter Approximate load dimensions: 1500x1000x1265 mm Estimated weight: about 700 kg The item is sold in the state in which it is, unverified and without warranty of operation. The sale is subject to acceptance by the seller and may be subject to restrictions, in particular for goods destined for countries to which export is required. Auction-ID: A7-39512-4

A small compressor system including separator and dryer is available. 1) Compressor Atlas Copco GA 18, year of manufacture: 1994, air volume flow: 36.4l/s, max. operating pressure: 10bar, motor power: 18.5kW, speed: 1500rpm. 2) Air dryer Schneider Druckluft GmbH DK 3000 N, max. inlet temperature: 50°C, max. operating pressure: 16bar, refrigerant: R134a, refrigerant charge: 700g, operating overpressure: 17bar. 3) Oil-water separator Donaldson Ultrasep Plus 30, max. residual oil content: 10mg/l, max. compressor capacity: 30m³/min, oil adsorption capacity: 25l, machine dimensions X/Y/Z: approx. 900mm/1000mm/400mm, weight: approx. 70kg. An on-site inspection is possible.

Boge DS2-DS30 Diesel-oil (1) -- Naphte (2) -- Electr (3): Elektr Max output: 10 bar voltage: 3 x 400V Volume flow rate: 0,50–0,54 m³/min Power imput: 4 kW Length: 480 mm Width: 907 mm Height: 955 mm Weight: 200 kg

Motor power: 11 kW Nominal flow rate: 1.5 m³/min Maximum working pressure: 10 bar Voltage/Phase: 380V Electrical protection: IP55 Management: Integrated inverter Approximate load dimensions: 1050x700x1050 mm Estimated weight: about 300 kg The item is sold in the state in which it is, unverified and without warranty of operation. The sale is subject to acceptance by the seller and may be subject to restrictions, in particular for goods destined for countries to which export is required. Auction-ID: A7-39512-2

for sale 5 compressors INGERSOLL RAND year 2004 at 2019 model: 2x units C70MK3 430 KW 1xunits MGP655D 48 KW 1xunits C700 100 630 KW 1xunits HKO 400 480KW

Motor power: 7.5 kW Nominal flow rate: 1.0 m³/min Maximum working pressure: 10 bar Voltage/Phase: 380V Electrical protection: IP55 Management: Integrated inverter Approximate load dimensions: 900x625x860 mm Estimated weight: about 200 Kg The item is sold in the state in which it is, unverified and without warranty of operation. The sale is subject to acceptance by the seller and may be subject to restrictions, in particular for goods destined for countries to which export is required. Auction-ID: A7-39512-1

power capacity: kW feed pressure: 16 bar liter capacity: 500 l total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Air compressor Operating temperature TS min 10 TS max. 50 degrees The technical data is provided by the manufacturer or operator and is thereforenon-binding for us. We reserve the right to prior sale, our terms and conditions of business and sale apply exclusively. About us: More than 400 of our own machines in stock Over 15,000 m² of warehouse space, 70-ton crane capacity More than 10,000 accessories for your workshop If you want to sell machinery, production lines, or your business, please contact us. Further offers can be found on our website. Viewings are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Motor power: 15 kW Nominal flow rate: 1.7 m³/min Maximum working pressure: 10 bar Voltage/Phase: 380V Electrical protection: IP55 Management: Integrated inverter Approximate load dimensions: 1050x700x1050 mm Estimated weight: about 300 kg The item is sold in the state in which it is, unverified and without warranty of operation. The sale is subject to acceptance by the seller and may be subject to restrictions, in particular for goods destined for countries to which export is required. Auction-ID: A7-39512-3

Two ALUP compressors including two heat exchangers are available. Operating pressure: 7bar, max. pressure: 13bar, max. inlet temperature: 55°C, power range: 11kW-30kW, refrigerant: R513A, refrigerant quantity: 500g, weight: approx. 290kg. Documentation available. An on site inspection is possible.

Offered are 2 screw compressors with the following features per unit: Power: 15kW, pressure: 10bar, volume flow: 1950l/min (1.95m3/min), speed: 2930rpm, including sound enclosure, 1) year of construction 1989, operating hours: approx. 38100h, 2) year of construction 1986, operating hours: approx. 10600h. Inspection possible by appointment.

feed pressure: 8 bar Effective free air delivery: 235/165 L/min Receiver capacity: 50 / 10 l / bar weight of the machine ca.: 37,5 kg. Number of cylinders: 2 Stk. motor: 230V / 1,5KW V / KW range L-W-H: 790 x 400 x 730 mm This oil-free and compact Hyundai compressor has a low weight and super-quiet operation. Very quiet, about 53-60dB (Suitable for indoor use) Equipped with: ? safety valve. ? Pressure regulator with pressure gauge and coupling. ? Drain valve on the tank. ? Humidity separator. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Two identical compressors with integrated refrigerated dryer are offered. Pressure dew point: +3°C, rated power: 30kW, delivery rate (FAD): 5.31m³/min at 8bar, 4.77m³/min at 10bar, 3.86m³/min at 13bar, control: Boge Autotronic, fully automatic operation. Inspection is possible by arrangement.

Engine power: 30 kW (for the 30 kW class). Control: Standard with SIGMA CONTROL 2 for automatic control, monitoring and energy optimization. Special features: SIGMA PROFIL® screw block for high energy efficiency, with refrigeration dryer for compressed air drying

Operating hours: 70792 h Equipment / Additional information: The compressor is water-cooled and has heat recovery. Rated power: 160.0 kW Motor speed: 1500 rpm Max. operating pressure: 8.5 bar Ambient temperature: 3°C/45°C

Refrigerant compressors system Bitzer -Type: 4HTC-20KI-40S (x3), 2HHC-2KB-40S (x2) -Volume: 12 m3/h (x3), 4.34 m3/h (x2) -Control cabinet included -Dimensions: 3200 x 870 x 1850 mm -Cabinet dimensions: 2050 x 1200 mm -Refrigerant: CO2 -Items in magazine: 1 -Reference number: Z122 -Condition: Used in very good condition, ready to work

Operating hours: 39521 h Equipment / Additional information: The compressor is water-cooled and has heat recovery. Rated power: 110.0 kW Motor speed: 1485 rpm Max. operating pressure: 8.5 bar Ambient temperature: 3°C/45°C

Refrigerant compressors system Bitzer -Type: 4FTC-20KI-40S (x3), 2HHC-2K-40S (x1), 2KHC-05K0-40S (x1) -Volume: 17.8 m3/h (x3), 4.34 m3/h (x3), 2.71 m3/h (x3) -Control cabinet included -Dimensions: 2950 x 950 x 1950 mm -Cabinet dimensions: 2050 x 1200 mm -Refrigerant: CO2 -Items in magazine: 1 -Reference number: Z121 -Condition: Used in very good condition, ready to work

Manufacturer: KAESER Model: BSD 72 SFC Year of Manufacture: 2012 Machine type: Screw Compressor Rated Power: 37.0 kW Motor Speed: 2960 1/min Max. Operating Pressure: 8.5 bar Ambient Temperature: 3 degrees C / 45 degrees C

High pressure compressor LMF 40 bar Type: Eco Pet VD 1350 - B Year of manufacturing: 2003 Capacity: 1.350 m³/h Maximan pressure: 42 bar Electric power: 243 kW Working hours: approx. 35.800 h with Siemens S7 PLC and Danfoss frequency drive incl. pressure air buffer tank, 900 ltr. incl. air dryer incl. chiller / cooling tower the machine is dismantled and on stock in Germany

Technical data: - Operating hours 4248 h - Load hours 1978 h - Operating pressure 10 bar - Delivery rate 3.34 m³/min - Drive 400 V / 22 kW - Motor speed 3000 rpm - Space requirement approx. W 1300 x H 1250 x D 800 mm - Weight approx. 490 kg