aluminium used for sale

DIMENSIONS: 4310 x 2032 x 660 MM & 4953 x 2032 x 660 MM,

Silo, flour silo storage silo, aluminum silo, storage silo used Volume: approx. 84 m³ Cylindrical height: approx. 12.0 m Year of construction: 1988 Diameter Ø: approx. 3.0 m total height: approx. 14.7 m Upper inlet: approx. manhole Ø 840 mm, inlet Ø 270 mm Outlet: approx. Ø 300 mm Weight approx. 3.3 t Material: Aluminum The silo was used as a storage silo (standing/hanging) in a mill. Subject to changes and errors in the technical data, specifications and prices as well as prior sale.

Silo, flour silo storage silo, aluminum silo, storage silo used Volume: approx. 58 m³ Cylindrical height: approx. 12.0 m Diameter Ø: approx. 2.5 m total height: approx. 13.9 m Upper inlet: approx. 1 x Ø 270 mm, 1 x Ø 150 mm Outlet: approx. Ø 390 mm Weight approx. 2.3 t Material: Aluminum The silo was used as a storage silo (standing/hanging) in a mill. Subject to changes and errors in the technical data, specifications and prices as well as prior sale.

Box Width:750 Box Height:1000 dimensions of the machine ca.:1200 m2 Powder Coating Line EISEMANN very less used and in very good condition. New Price of the plant 2.600.000,- EURO Power & Free conveyor system with 250 car trains, 5-Zone Spray Pre-Treatment System, stainless steel - water drying cooling zones. 2 nos.of WAGNER stainless steel powder cabins each with ABB robots & double-automatic powder guns, as well aseach cabin is equipped with a hand-powder device. Powder Curing Oven, direct gas heated three-zone Spray cleaning equipment, Stainless Steel - Sewage Treatment Plant, Evaporator with Reverse Osmosis System & Fresh-Air Device. Opening Cross Section Areal: Width 750 mm, Height 1000 mm Technical Details: Pretreatment conveying speed 2.3 m / min. Pretreatment surface area approx. 200 m2 / h. Painting Surface approx. 120 m2 / h. Throughput of workpieces approx. 4,000 k This Powede ...

Nitrogen Furnace nitrogen furnace Pit furnace, top condition. 50kW ele Max T. 950°C Anealing in hydrogen, nitrogen atmospere Batch size 800x1000mm run only for tests and start of production similar possible furnace REY, Naberther, CFI, SAIREM, SOLO, ALD, ECM, BMI, CERIC WISTRA, ELTI, ECM, NAGAT SAT, SAFED, SERTHEL, SLFI, MORGAN, OTTO JUNKER, CIEFFE Anlaßöfen mit Luftumwälzung Anwärmöfen Aluminium – Glühöfen Abschreckbäder Beschickungsanlagen für Druckgußmasch inen Drehherdöfen Doppelkammeröfen Draht – Glühöfen Durchlauföfen Elev atoröfen Glühöfen für verschiedene Einsatzarten Gas Nitrieröfen Härteöfen Härtebäder Herdöfen Hubbalkenöfen Herwagenöfen Haubenöfen Industrie Trockenanlagen Kammeröfen Kunststoff - Beschichtungsöfen Carbonitrieren Härten Vergüten Härten von Kaltarbeitsstahl Härten von Warmarbeitsstahl Induktivhärten Flammh ...

We offer a position Doka Framax Alu 186,759m² in good ready-to-use condition with up to 75% discount! Partially new formwork - new value = 176.805,40€ Special net price 53.512,74€ Formwork completely cleaned, inspected and sorted. Formlining exposed concrete class 2/3 or newly covered with Finply formwork. Out-of-the-box, suitable for higher-value use. Pcs. Designation 28 Alu-Framax Xlife-Element HK 0.90x 2.70m 3 Alu-Framax Xlife-Element HK 0.90x 2.70m – newly occupied 3 aluminium Framax Xlife element HK 0.75x 2.70m 1 aluminium Framax Xlife element HK 0.75x 2.70m – newly occupied 15 Alu-Framax Xlife-Element HK 0.60x 2.70m 5 Alu-Framax Xlife-Element HK 0.60x 2.70m – newly occupied 10 aluminium Framax Xlife element 0.45x 0.90m 3 Alu-Framax Xlife element 0.45x 0.90m – newly occupied 3 aluminium Framax Xlife element 0.30x 2.70m 7 Alu-Framax Xlife el ...

Furnacce 1200 hardness tester 300x300x500 mm Temperature max 1200C Ölbrenneranlagen Retortenöfen Teil Vakuum Rollenherd - Durchlauföfen Rohrglühöfen Salzbadöfen Schmiedeöfen Schachtöfen Stoßöfen Schüttelherd - Härteöfen Schutzgas Topfglühöfen Tiegelschmelzöfen Truhenöfen Transporttiegel für Flüssigmetall Transport - Warmhalteöfen für Flüssigbeschickung Umschmelzöfen für Aluminium Verzinkungsöfen Vergüteöfen Warmhalteöfen Herdwagenofen Rollenherdofen Kammerofen Drehtellerofen Wagenherdofen Tunnelofen Haubenofen Schachtofen Sonderanlagen Anlaßöfen mit Luftumwälzung Anwärmöfen Aluminium Glühöfen Abschreckbäder Beschickungsanlagen für Druckgußmaschinen Drehherdöfen Doppelkammeröfen buerstlein Draht Glühöfen Durchlauföfen zirlguss Elevatoröfen Glühöfen für verschiedene Einsatzarten Gas Nitrieröfen Härteöfen Härtebäder Herd ...

Model: R950-08 Power: M2-M8 Speed (rpm): 700 Air requirement: 750l/min Pressure: 6-7bar Working range: Rmax 950mm Construction parallel arm: Stable arm structure (hard aluminium profile 38x29) Weight: 18kg Adapter Holder: TCS 1B Model: R950-12 Power: M3-M12 Speed (rpm): 400 Air requirement: 750l/min Pressure: 6-7bar Working range: Rmax 950mm Construction parallel arm: Stable arm structure (hard aluminium profile 38x29) Weight: 18kg Adapter Holder: TCS 1B Model: R950-16 Power: M3-M16 Speed (rpm): 300 Air requirement: 950l/min Pressure: 6-7bar Working range: Rmax 950mm Construction parallel arm: Stable arm structure (hard aluminium profile 38x29) Weight: 25kg Adapter Holder: TCS 2B Model: R950-020 Power: M3-M20 Speed (rpm): 150 / 400 Air requirement: 950l/min Pressure: 6-7bar Working range: Rmax 950mm Construction parallel arm: Stable arm structure ...

Model: R1450-08 Power: M2-M8 Speed (rpm): 700 Air requirement: 750l/min Pressure: 6-7bar Working range: Rmax 1450mm Construction parallel arm: Stable arm structure (hard aluminium profile 38x29) Weight: 23kg Adapter Holder: TCS 1B Model: R1450-12 Power: M3-M12 Speed (rpm): 400 Air requirement: 750l/min Pressure: 6-7bar Working range: Rmax 1450mm Construction parallel arm: Stable arm structure (hard aluminium profile 38x29) Weight: 23kg Adapter Holder: TCS 1B Model: R1450-16 Power: M3-M16 Speed (rpm): 300 Air requirement: 950l/min Pressure: 6-7bar Working range: Rmax 1450mm Construction parallel arm: Stable arm structure (hard aluminium profile 38x29) Weight: 27kg Adapter Holder: TCS 2B Model: R1450-020 Power: M3-M20 Speed (rpm): 150 / 400 Air requirement: 950l/min Pressure: 6-7bar Working range: Rmax 1450mm Construction parallel arm: Stable arm s ...

Model: R1950-08 Power: M2-M8 Speed (rpm): 700 Air requirement: 750l/min Pressure: 6-7bar Working range: Rmin 300mm – Rmax 1950mm Construction parallel arm: Stable arm structure (hard aluminium profile 38x29) Weight: 23kg Adapter Holder: TCS 1B Model: R1950-12 Power: M3-M12 Speed (rpm): 400 Air requirement: 750l/min Pressure: 6-7bar Working range: Rmin 300mm – Rmax 1950mm Construction parallel arm: Stable arm structure (hard aluminium profile 38x29) Weight: 23kg Adapter Holder: TCS 1B Model: R1950-16 Power: M3-M16 Speed (rpm): 300 Air requirement: 950l/min Pressure: 6-7bar Working range: Rmin 300mm – Rmax 1950mm Construction parallel arm: Stable arm structure (hard aluminium profile 38x29) Weight: 27kg Adapter Holder: TCS 2B Model: R1950-020 Power: M3-M20 Speed (rpm): 150 / 400 Air requirement: 950l/min Pressure: 6-7bar Working range: Rmin 30 ...

furnace oven kiln 1200 1x1x2m bogie PLC Härten Vergüten Härten von Kaltarbeitsstahl Härten von Warmarbeitsstahl Induktivhärten Flammhärten Anlassen / Glühen Bainitisieren Entspannen / Anlassen Anlassofen Aushärteöfen Chargen trockner Drucksinteröfen Durchlauföfen Durchlauftrockner Elektroindustrieofen Elektroöfen Erwärmungsöfen Gasöfen Gastrockner Industrieöf en Industrietrockner Kammeröfen Kammertrockenöfen Kammertrockner Öfen Ölofen Pulverbeschichtungstrockner Pulvereinbrennöfen Schachtöfen Schlichtetrockner Sinteröfen Sonderofen Sondertrockner Temperöfen Trockenöfen Trockner Tro ckneranlagen Vorwärmofen Wärmebehandlungsöfen Wärmeofen Wärmeprozessöfen Warmhalteofen Warmluftofen Herdwagenofen Rollenherdofen Kammerofen Drehtellerofen Wagenherdofen & Tunnelofen Haubenofen Schachtofen Sonderanlagen Durchlauföfen Herdwagenöfen Kammeröfen  ...

Heat treatment oven 1150 0.8x0.8x1.5m t max 1150 C possible various size ovens Öfen für die Wärmebehandlung Metalle einfache Härtesysteme Härterei-Zubehör gienanth Glühöfen Umluftöfen zum Glühen, Anlassen Salzbadöfen Schutzgasöfen Nitrieröfen und Plasmanitrieröfen Mehrzweckkammer-ofenanlagen kontinuierliche Ofenanlagen Vakuumprozesse Vakuumhärten Vakuumglühen, -anlassen, Nitrieren Vakuumlöten Metal Injection Moulding Induktionserwärmung Öfen für die Kunststofftechnik zum Trocken, Tempern, Polymerisieren, Einbrennen usw.; Ausführung als Kammeröfen, Haubenöfen, Herdwagenöfen, Schachtöfen; Herdwagen-Schmiedeöfen Umluftöfen Kammerofenlinien Nitrieröfen Plasmanitrieröfen Vakuumprozesse Schmelzöfen Trocknen Tempern Laboröfen Ersatzteile Öfen Kammeröfen Herd wagenöfen schoenheider Herdwagenöfen zirlguss Glühen Härten Tempern Umformen Vorw ...

Kiln 1200C inner dimensions 1x1x2m 2 heating zones auto door Fours pour la fonderie Fours pour la forge et le matriçage Fours pour les traitements thermiques Equipements périphériques Fours pour verres feuilletés Fours Basse température Fours à passage continu Fours céramique Fours à creuset pour fusion et fusion-maintien des métaux non ferreux Creusets pour fonderie Fours pour cuisson et décirage de carapaces de fonderie à cire perdue Fours de forge standard Fours à creuset Fours Haute température Fours de laboratoire Fours de trempe Fours de recuit chauffé à l'électricité chauffé au gaz four standard chauffés à l'électricité four standard chauffés au gaz Fours à longerons mobiles Fours de thermoformage Fours de séchage Fours de polymérisation Fours pour le verre Fours Fours à sole tournante de bombage Fours de revenu  ...

K240/12 nabertherm . Foundry machines furnace, ovens Nabertherm Kippofen 600kg Aluminium Nabertherm Kippofen 600kg Aluminium Balzer Kippofen 600kg Aluminium Balzer Schöpfofen 300kg Aluminium Fulmina Wannenkippofen 20 to Zamak/Zink Reißaus Durchlaufmischer 4-8 to Furansand AXA Fräsmaschine 2300x1190x600 Silo Ø 2500x5000 Sand

K240/12 nabertherm . Foundry machines Nabertherm Kippofen 600kg Aluminium Nabertherm Kippofen 600kg Aluminium Balzer Kippofen 600kg Aluminium Balzer Schöpfofen 300kg Aluminium Fulmina Wannenkippofen 20 to Zamak/Zink Reißaus Durchlaufmischer 4-8 to Furansand AXA Fräsmaschine 2300x1190x600 Silo Ø 2500x5000 Sand

Fully reconditioned foil wrapping machine which can be used for packing products butter, lard, margarine, tvorog or cottage cheese into aluminium foil or parchment paper. This machine is general overhauled and in a as good as new condition with new controls with frequency converter (renewed in 2022). The format on the machine is 250 gram, 100 x 75 x 35 mm, bottom folding. The butter is feed with an aluminium through with aluminium augers. Aluminium dosing station. The machine is equiped with a photocell on the paper infeed, to control the exact position of the print on the foil. If there is no foil in the cell, the machine will stop. The speed can be adjusted by a frequency converter between 40 - 90 packages per minute (depending on filling weight, product, product viscosity and quality packaging). Outfeed conveyor. On request we can do a dry test (without product) with your own foil on  ...

Fully reconditioned foil wrapping machine which can be used for packing products butter, lard, margarine, tvorog or cottage cheese into aluminium foil or parchment paper. This machine is general overhauled and in a as good as new condition with new controls with frequency converter (renewed in 2023). The format on the machine is 500 gram, 125 x 75 x ±56 mm, bottom folding. The butter is feed with an aluminium through with aluminium augers. Aluminium dosing station. The machine is equiped with a photocell on the paper infeed, to control the exact position of the print on the foil. If there is no foil in the cell, the machine will stop. The speed can be adjusted by a frequency converter between 40 - 70 packages per minute (depending on filling weight, product, product viscosity and quality packaging). Outfeed conveyor. On request we can do a dry test (without product) with your own foil o ...

Foil wrapping machine which can be used for packing products butter, lard, margarine, tvorog or cottage cheese into aluminium foil or parchment paper. This machine is in a reasonable mechanical and electrical condition (renewed by Schuy, auftr. nr: 13632-01). The format on the machine is German Standard size: 250 gram, 100 x 75 x 35 mm, bottom folding. Capacity: up to 50 portions per minute. The butter is feed with an aluminium through with aluminium augers. Aluminium dosing station. The machine is equiped with a later build on photocell on the paper infeed, to control the exact position of the print on the foil. Outfeed conveyor., Additional features:, Excluding:, - Datecoder., Type of Machine: Butter Packaging Machine, Capacity: ± 750 Kg/h, Capacity (Units): up to 50 packages per minute, Packaging Weight: 250 gram, Packaging Size: 100 x 75 x 35 mm (German standard), Packaging type: Bo ...

Fully reconditioned foil wrapping machine which can be used for packing products butter, lard, margarine, tvorog or cottage cheese into aluminium foil or parchment paper. This machine is general overhauled and in a as good as new condition with new controls with frequency converter (renewed in 2023). The format on the machine is 250 gram, 100 x 75 x ±35 mm, bottom folding. The butter is feed with an aluminium through with aluminium augers. Aluminium dosing station. The machine is equiped with a photocell on the paper infeed, to control the exact position of the print on the foil. If there is no foil in the cell, the machine will stop. The speed can be adjusted by a frequency converter between 40 - 90 packages per minute (depending on filling weight, product, product viscosity and quality packaging). Outfeed conveyor. On request we can do a dry test (without product) with your own foil o ...

Metal press RMH MB (Mini Baler) This machine is particularly suitable for pressing aluminium, copper, zinc and other metals. The RMH MB Mini Baler is able to crush and then press larger material made of aluminium, copper, zinc and other metals thanks to lateral knives on three sides of the filling box. Technical data: Drive: 7.5 Kw / 400 V Weight: 1.8 T Shear lid pressure: 20 t Ground ram pressure: 40 t Working pressure: 220 BAR Filling box dimensions (L x W x D): 81.5 cm x 35 cm x 51 cm Package dimensions (L x W x material quantity): 35 cm x 20 cm x variable length (material quantity) Pressing cycle: about 1 minute Dimensions (L x W x H): 2.45 meters x 1.20 meters x 1.40 meters CE Norm Metal Baler RMH MB (mini baler) Cutting edges on three sides of the bale box and lid give this machine the ability to handle with oversized materials out of aluminium, copper,  ...

Pneumatic valve DN 300 Manufacturer: Jaudt Dosiertechnik Maschinenfabrik GmbH Type: Varioschieber FSV Opening width mm: ø 350 Height mm: 130 Max.Working temp. ° C: 80 Operating pressure MPa: 0.6-1.0 maximum operating pressure MPa: 0 Control voltage V: -. Housing: one-piece cast housing in flange version the round face with coarse good Chicane Sealing: slide sheet implementation for with Adjustable stuffing seal Pressure piece from cast aluminium alloy Blade: Stainless steel 1.4301 Slide sheet: eccentric screws galvanized Finish: Stainless steel and aluminum parts blank Grey cast iron housing painted in RAL 9006 Steel parts zinc plated, 10 & #956; m Plate made of aluminium Housing material: Cast aluminium alloy (AlSi 10 mg) shock-proof up to 5 bar Flanschbohrbild: According to DIN 2501 PN 6 Packing material: ARAMIDE (Tmax 280 ° C) Operation: pneu ...

LAMINATING SYSTEM POLYTYPE BB 2200 LAMINATION LINE Coating/- lamination equipment for solvent based resin system. On an existing film or composite material. Year: 2008 Condition: Excellent The different film thicknesses what can be used depending on the materials, see references: Plastic foils 25-250 microns Metal foils (copper, aluminium) 20-150 microns Total composite thickness max. 500 microns Machine data: Production speed 0 - 150m/min Production speed 840 - 2160mm Resin 1 - 40g/m2 Winding units (main winder-/ lamination winder-/tensilized film winder): For unwind of the base film there are two winders (main winder/ lamination winder). Winder performance: - Winding direction clockwise / anticlockwise - Brakes ystem for constant and regulated tension e.g. alu foil with max. 2000 kg roll weight - Roll system centerless for steel,plastic-, carton tubes with optimal  ...

Very fast running agitator 0.25 KW - 3400 rpm. with aluminium propeller 300 mm Electric motor: Used electric motor 0.25 KW, 3 x 230/400 volts, n = 3,400 rpm, Weight approx. 10 kg. With motor protection plug. Wave: Precision stainless steel shaft D14, length 500 mm, diameter 14 mm, Material stainless steel 1.4301. Rigid clutch made of aluminium. Stirring organ: Two-flyer aluminium propeller d = 300 mm.

Description Brand GUNTNER Model GHF 050/1E/17 ID 109454-16 Status Active Price 1.600 € + VAT Year of manufacture 2011 Location Oradea (RO) Cooling equipment | GUNTNER GHF 050/1E/17 manufactured in 2011. Size (L x W x H): 1000 x 500 x 500 mm. 2 pieces available, one missing a fan. Heat Exchanger Aligned or staggered tube pattern Special copper tubes for HFC, coolant and CO2 Stainless steel tubes for NH3 Surface-corrugated aluminium fins for high heat transfer Casing Corrosion-resistant aluminium alloy AlMg up to 500 mm fan diameter Powder-coated with RAL 9003 Hinged side cover with hinges Tray Hinged and thermally-decoupled (condensation free) Separate drip plate Corrosion-resistant aluminium alloy AlMg Powder-coated with RAL 9003 Large condensation drain with 45° incline Fans Proven quality fans Standard with two speeds (for fan diameter of 50 ...

McIntyre M20 Can / Metals Baler Protect the environment and generate income by baling aluminium and steel cans. Versatile The M20 Baler is not only a cost effective system for cans but can also be used for many other applications where automatic volume reduction or product destruction is required. The M20 Baler will accept cans up to 250mm x 480mm and will produce up to 500kg of 20g aluminium drink cans per hour. The smaller the size of the can, the greater the machine output. When fed with aluminium drinks cans, the M20 crushes and locks the material together to produce dense 274mm cubes, weighing approximately 9- 11kgs. Such dense bales means that no tying or strapping is needed. The cubes are simply ejected from the machine and ready for transportation. Optinally, you can buy it, with can sorter!

oven 700 Uterna Europe 80KW 700 Celsius Ziel des Spannungsarmglühens schoenheider ist die Reduzierung von Eigenspannungen im Material. Solche Spannungen entstehen zum Beispiel durch Gefügeumwandlungen, Kaltverformung und durch spanende Bearbeitung. Wichtig für ein gutes Ergebnis ist nicht nur die richtige buerstlein Temperatur, sondern auch eine umsichtige Abkühlung. Nur so lässt sich eine erneute Spannungsbildung vermeiden. Typischerweise findet das Spannungsarmglühen bei Temperaturen um 600 °C (bei zuvor vergüteten Bauteilen jedoch 30-50 °C unter der letzten Anlasstemperatur) statt. Die Wärmebehandlung ist das häufigste Veredelungsverfahren, mit dem die Eigenschaften der Stähle gezielt verändert und ihre optimalen Gebrauchseigenschaften für den jeweiligen Einsatzzweck herbeigeführt werden. Erst durch eine der Stahlzusammensetzung, dem Verwendungszweck und der Baut ...

NEW - Unused stock from industrial hall packed in original wooden box Offer valid for acceptance of 115 pieces - partial quantities possible Manufacturer: Coat plates with ventilation slots aluminium natural, upper ribbed and lower end part made of cast aluminium. Aluminum reflector open, removable. VG with thermal protection element and. if necessary, ZG with automatic shut-off installed. 4 Cable entries M20. Connections inside, large side connecting door. Central threaded bolt M10 for ceiling sheet or hanger. Lamp: HST-DE, 400 W Number of lamps: 1-lamp Material of the housing: Aluminium Case color: Aluminum Lamp power: 1 x 400 W System power: 440 W Protection class: I Degree of protection (IP): IP20 Control unit VG, Length: 536 mm Width: 536 mm Height: 692 mm max. weight: 13.8 kg 230 V - 240 V AC

Machine code: IT352 Manufacturer: Uhlmann Model: UPS300 Year of construction: 2001 Uhlmann This is a fully automatic, intermittent motion Blisterpacking machine with a capacity up to 50 cycles per minute. The maximum output is 200 Blisters per minute depending on blister size. The machine is of ‘balcony construction’ - all relevant stations are individual modules, which are cantilevered off a large aluminium plate that forms the front of the machine housing. The remainder of the machine cabinet is constructed from fabricated steel and houses the drive unit, gear trains, chain drives and the electrical control equipment. PVC, PVC/PVDC, PVC/Aclar film is drawn from a reel and is first heated and softened and then deep-drawn in the blister forming station. The blisters are formed in the mould with the aid of compressed air – the web is then pulled forward, up and across  ...

Qty. 1 Second-hand aluminium strip production plant Entry Material: Aluminium Scrap – HD666, AA5050, 2.5-3.0% Mg Final product: Aluminium strip (can stock) Width: 220 mm Thickness: 0.15 – 1.0 mm Mfc.: De Winter, Thermcon, Fata Hunter, Fröhling, Nederman, Burghardt & Schmidt, Siemens Built: 1984, 1999, 2000, 2002, 2014, 2015 Scope of supply: Melting Furnace Tilting Casting Furnace Block Caster 5 Stand Hot Rolling Mill 6 Stand Cold Rolling Mill Hot Gas Filter Slitter Welding Machine Treatment Furnace Quenching Unit Shear

Doka Alu Framax 127 m2 Good condition of frame and formwork skin (partly new Finply formwork skin or used X-Life formwork skin) Due to its lower weight, the aluminium frame formwork is suitable for shelling with and without a crane. Also seamless in combination with Framax steel formwork suitable. Lightweight and versatile due to sturdy profile frame made of aluminium Reduced workload when shelling by hand due to low element weight, with a high load capacity of 60 kN/m² can be implemented by hand or by crane thanks to frames made of torsion-resistant aluminium hollow sections Division into crane and hand formwork areas 20 x Element 0,90x2,70m 20 x Element 0,75x2,70m 14 x Element 0,60x2,70m 6 x Element 0,45x2,70m 6 x Element 0,30x2,70m 2 x Outer corner 2,70m 2 x Inner corner 2,70m Partial quantities are also possible! Doka Alu Framax 127 m2 Good condition ...

FRECH DAK315H die casting machine manufactured in 1991 by the German company Oskar Frech Werkzeugbau GmbH + CO. KG. is designed for the production of castings by filling moulds with molten brass or aluminium. The reliable FRECH metal injection moulding machine with high-quality components works with casting moulds of a maximum height of 700 mm, which are closed with a force of up to 315 tonnes after being filled with molten material. Depending on the design of the choiceed mould, the aluminium die casting machine also allows for the use of an injection piston with a diameter of 40 to 80 mm. Previously, the machine used a piston with a diameter of 40 mm. The DAK315H aluminium die casting machine weighs approximately 14000 kg. Technical parameters of the FRECH DAK315H metal injection moulding machine - clamping force: 315 t (3150 kN) - injection force: 35 t (350 kN) - ejection for ...

Furnace 1200 temperature 10 - 1200 Celsius 2 heating zones 100kW auto door PLC Poreba Gurutzpe Tacchi Geminis Tos Amutio cazeneuve Skoda Morando Niles Colchester Heyligenstaedt Kramatorsk Mondiale Safop Cazeneuve Alzmetall mas stankoimport csepel carlton kolb soraluce bergonzi flott Erfurt Weingarten smeral schuler ebu mueller zts kosice wlochy minster Stanko stankoimport glaser huta zygmunt aft donaldson eumuko Elblag Engel Demag Arburg Krauss Maffei Battenfeld Manesty Mazak Voronezh Trumpf Amada Cincinnati Netstal Rose Forgrove Illig Foremost Nissei Sandretto Fette Mazak Mori seiki Haas Okuma Gildemeister Doosan Daewoo traub hwacheon index Wema zeulenroda mueller Erfurt tox presso technik dunkes galdabini hare ponar zeulenrdoda eitel Ziel des Spannungsarmglühens ist die Reduzierung von Eigenspannungen im Material. Solche Spannungen entstehen zum Beispiel durch Gefügeum ...

3 x Diverter ZWR-150-AS/AS-H0/R2-D-S Distribution or collection element in pneumatic conveyor systems for powdered and granular Products from a wide range of industrial sectors. Factory No. / Item no. /Drive end: 92576 / -- / R 92577 / -- / R 92578 / -- / R GENERAL DATA Product: Li2Co3; LiOH Powder Bulk density: 380.0 kg/m3 Bulk density: 900.0 kg/m3 Grain size distribution: 0.050 mm Grain size distribution: 0.400 mm Product temp. min.: 10.0 °C Product temp. max.: 35.0 °C Ambient temp. min.: 10.0 °C Ambient temp. max.: 35.0 °C Discharge pressure: 0.00 bar (g) Explosion protection: According to customer specifications, no explosion protection provided Design data Max. operating pressure: 6.00 bar (g) Compressed air supply: 4.50 bar MATERIALS / DESIGN Execution: Distribution Housing: Cast aluminium EN AC-42100 (A375.0) with replaceable stainless steel in ...

- Granite top T/W/H: 750/ 500/ 20.5 mm - Aluminium plate B/D/H: 750/ 500/ 40 mm - Space requirement (W x D x H): 0.75 x 0.5 x 0.805 m - Machine weight: 370 kg - Condition: very good Details Measuring table or laboratory table with a granite plate and an aluminium plate with base frame glued to it, aluminium plate with threaded holes M8, hole spacing 50 mm

Articulated conveyor belt made of aluminium including substructure 3000 + 2500mm 45° inclination Angle conveyor made of aluminium for a wide range of applications 3000 mm flat + 2500 mm slope Aluminium construction: Conveyor belt incl. shaft edge on both sides Total width belt: 500 mm Green PVC conveyor belt, 3-layer, particularly transversely stable, endlessly welded with step connection 40x35mm shaft edge edge-free zone for belt guidance on both sides 70mm antistatic due to threads in the fabric of the running side Drive: Motor approx. 0.55 kW, speed 0.3 m/sec. controllable with frequency converter Connection 220 / 400V, 50Hz protection class IP54 Drive, motor control optional Our core competence lies in providing the customer with exactly what he really needs. Together with our customers, we develop customer-specific, individual solutions and supply correspond ...

PRIMA POWER PLATINO 1530 laser was manufactured in 2001 in Italy. The machine is designed for cutting metal sheets made of structural steel, stainless steel and aluminium. The processed sheet may be up to 15 mm thick (structural steel), 8 mm thick (stainless steel) or 5 mm thick (aluminium). The feed rates in the X/Y/Z axes are 3000 mm (X axis), 1500 mm (Y axis) and 140 mm (Z axis) respectively. The laser cutting machine is equipped with a high performance ROFIN SINAR SLAB DC025 resonator with a power of 2500W, created for fast and precise cutting in metal sheets and guaranteeing the highest quality of cut elements. The installed PRIMACH 20L CNC control allows memorising many different work programmes and controlling every aspect of machining. The machine is offered with a wide range of equipment, including: CAD/CAM software SiCam v14 (license for one workstation) and post-processo ...

ECKERT JANTAR plasma cutting machine was manufactured in 2017 in Poland. Characterised by a robust and stable construction, the machine is designed for cutting shapes in workpieces made of mild steel, stainless steel or aluminium. For precise machining of sheets having a maximum thickness of 38 mm (mild steel) or 25 mm (stainless steel and aluminium), it uses a plasma torch equipped with an HD3000 support with distance adjustment by measuring the plasma arc voltage. The process of cutting workpieces is carried out on a working area measuring 2000 mm in length and 3000 mm in width, equipped with an extraction table eliminating the impurities generated during processing. The plasma cutting machine is offered with a wide range of equipment, including: modern CNC controller ECS 872 for full control over the operation of the machine, and a HYPERTHERM HPR130XD plasma source. Technical da ...

High speed 5 axes CNC machinning center CMS Concept 40/155/25 PX5 was built in Italy in 2020. CNC gantry milling machine characterised by outstanding robustness and reliability, is designed for precision milling, drilling and 3D machining of parts made of materials such as sand, epoxy and phenolic resin, carbon fibre, fibreglass and aluminium. Dimensioning of workpiece structures is performed by an advanced calculation programme based on the finite element method (FEM), ensuring high geometric accuracy and reliability, even under heavy workloads. Applicable to a variety of industries, the machining centre for composites and aluminium, features a mobile bridge with a PX5 5-axis workhead running on two electrically welded rigid guideways. All five interpolated axes of the head (X,Y,Z,C,A), are equipped with high-performance servomotors and pneumatic brakes. The high-speed electro-spindl ...

BYSTRONIC BYSTAR 3015 4.4 kW laser, manufactured in Switzerland in 2012 is designed for cutting metal sheets made of black steel, stainless steel and aluminium. Workpieces with a maximum thickness of 25 mm (black steel), 20 mm (stainless steel) or 12 mm (aluminium) are machined with the highest precision and quality, using a 4.4 kW laser beam emitted by a reliable BYSTRONIC ByLaser 4400 laser source. The laser cutting machine is characterised by a large working area made of high-quality steel, with a length of 3000 mm and a width of 1500 mm, allowing for easy loading of workpieces with a maximum weight of 890 kg and ensuring high stability during the cutting process. The machine is controlled via an arm-mounted control panel with installed BYSTRONIC ByVision numerical control. The laser has been continuously repaired – the following components have been replaced during the use of ...

MAZAK SUPER TURBO X48 MK II laser was built in 2001 in Japan. The compact laser cutting machine is designed for precise cutting of pre-programmed shapes in sheet metal made of structural steel, stainless steel and aluminium. The machine’s small dimensions and components integrated into the machine frame, such as the chip conveyor and the MAZATROL L32B CNC control, allow it to be used to its full potential both in small factories and in series production. The MAZAK ST-X 48 MKII gas cutting machine can process sheets with a maximum thickness of 15 mm (S235 structural steel), 6 mm (stainless steel) and 3 mm (aluminium). High cutting speed as well as excellent machining quality and accuracy over the entire working area at low operating costs are achieved thanks to the YB-L150A 8M resonator, characterised by high energy efficiency, allowing the laser beam power to be adjusted in the rang ...

TRUMPF TruLaser 3030 laser cutting machine was manufactured in 2011. The machine is equipped with modern components to provide precise cutting of workpieces made of mild steel, stainless steel and aluminium. High stability during processing is ensured by the steel body on which a state-of-the-art SIEMENS SINUMERIK 840D CNC controller is mounted for programming operating modes and control of the cutting process. The TruLaser 3030 Basic Edition laser cutting machine cuts metal sheets with a maximum weight of 900 kg and a thickness of 20 mm (mild steel), 12 mm (stainless steel) and 8 mm (aluminium) using a 3.2 kW laser beam, guaranteeing high precision and smooth and even workpiece edges. The laser is also equipped with an automatic pallet changing system. The total weight of the machine is 11500 kg. Technical data of the TRUMPF TruLaser 3030 laser cutting machine - CNC control: SIEM ...

saw blade diameter: 400 mm Number of revolutions: 3000 r.p.m hole of sawblade: 32 mm sawblade width: 4 mm Control: NC total power requirement: 1,5-2 kW weight of the machine ca.: 162 kg required space: 740 x 780 x 1350 mm The Gerd Wolff AC 400 is an automatic aluminium cutting machine which is manufactured for our sales brand GERD WOLLF Maschinenfabrik by a renowned manufacturer from Türkiye. Standard Accessories -BLocation points for 15° – 22.5° – 30° – 45° – 67.5° - Fixing handle for locking at intermediate angles - Adjustable cutting speed for different types of profile - Saw covering with safety switch - Belt propulsion saw - Two hand safety operation - Easy to change saw blade - 2 x Pneumatic vertical piston with clamps - 1 x compressed air pistol Optional Equipment - Hydrocheck – Hydraulic speed adjustment for aluminium profiles - Cooling system for aluminium cutt ...

Paul Köster leak testing system for die-cast aluminium or cast aluminium housings in good condition. 2 city ions with workpiece carrier system for different tool holders. Connection option for compressed air and hydraulics directly on the workpiece carrier. Test container approx. 1600 x 2200 mm, depth approx. 900 mm. The system was used to test die-cast aluminium gear housings. Immediately available from stock.

Icma San Giorgio MCM/60V – 40D twin screw co-rotating extruder Mod. MCM/60V-40 D and down stream equipment High performances, intermeshing screw type for self cleaning characteristics. Screws Ø 60 mm Nominal L/D ratio 1:40 Max screw speed 300 rpm Barrel Modular design made up by 10 square-barrel sectors, each one 4 D long Barrel sectors made of LK3 nitrided steel Built-in water cooling circuit, simple construction and easy to maintain High efficiency heating system by cartridge heater Broached shaft made in special alloy brake/yield/torsion resistant Modular design Screw elements made of K 110 wear resistant steel Gear box Torque per screw shaft Nm. 1050 per each shaft Gear-ratio 4.28 : 1 Min. bearing lifetime at max. speed and motor power 20,000 working hours @ 160 bar Main A.C. motor Power applied to gearbox shafts KW 66 Speed rpm 1285 Water cooling unit  ...

Foil wrapping machine which can be used for packing products butter, lard, margarine, tvorog or cottage cheese into aluminium foil or parchment paper. This machine is in a resonable mechanical condition but with almost new controls with frequency converter (renewed in 2020 by Elesto Austria with new Siemens S7-1200 PLC, touchscreen panel and CE declaration). The format on the machine is stick pack 100 and 250 gram, 100 x 37 x 30 / 75 mm, side folding. The butter is feed with an aluminium through with aluminium augers. Stainless steel dosing station. The machine is equiped with a photocell on the paper infeed, to control the exact position of the print on the foil. If there is no foil in the cell, the machine will stop. The speed can be adjusted by a frequency converter. Outfeed conveyor of 150 cm. Semi automatic case packer Benhil 8538 (year 1976, serialnumber: 538/1) for 2,5 kg boxes wi ...

Paul Köster leak testing system for die-cast aluminium or cast aluminium housings in good condition. 2 city ions with workpiece carrier system for different tool holders. Connection option for compressed air and hydraulics directly on the workpiece carrier. Test container approx. 1600 x 2200 mm, depth approx. 900 mm. The system was used to test die-cast aluminium gear housings. Immediately available from stock. Special price free trucks loaded until the end of November 2023 on request.

Complete signmaking equipment Made in USA for fast producing channel letters! For EU customers we provide FREE SHIPPING to your door! The machines are in operating condition, ready to use. 1. Multifunction Automatic CNC Metal Channel Letter Bending Machine (Flange & Notch functions) CNC metal channel letter bender capable for fully automatic channel letter fabrication, whereby producing cuts, bottom notched flange and bending of channel letters returns. It is capable to make aluminium channel letters with trim cap. We can provide well written manual in English and training on our premises if asked. 2. Norlok Letterlok 4000 Automatic Clincher Machines for Aluminium Channel Letters Norlok Letterlok 4000 Clincher is particularly designed for fastening the letter returns and letter backs. It uses newest technique power to connect metals without drilling, spot welding and  ...

The ELUMATEC SA 142/36 automatic aluminium cutting saw was manufactured in 2001 by the German brand ELUMATEC. The machine can be used for cutting aluminum profiles and PVC joinery. So far, it has only been used for cutting aluminium profiles. - Surface-specific material feeding (cyclic) via profile lifting system on one level - Single, double or triple feeding via selector switch - Safe material feeding thanks to two horizontal pressure cylinders Cvmmdigqg2 - Large cutting surface for wide profiles Technical parameters of the ELUMATEC SA 142/36 aluminium cutting saw: - saw speed: 2800 rpm. - cutting angle: 90 degrees to 45 degrees at SA 142/36 - cutting angle: 90 degrees at SA 142/36 - power output: 4000 W - Cutting unit feed: adjustable gradually - feed length/stroke : 5 to 730 mm - material transport: transport in step steps, pneumatic - air consumption without sprink ...

Dowel hole drilling machine Brand: VITAP Type: ALFA 21 CLASSIC New machine - One boring unit 21 spindles - QUICK CHANGE SPINDLES - Pneumatic cylinder for horizontal/vertical positioning of the boring group (45 degreed and any intermediate angles) - Front/top caliper to obtain the same boring measure between horizontal and vertical position - Tilting side stops adjustable by metric scale and nonius and magnifying lens on each stop - 2 safety clamps inclined 4 degrees - Height regulation of the boring group by mechanical digital position indicator; - 6 positions turret to adjust the drilling depth (0-80 mm) - Automatic vertical-horizontal depth difference device (10 mms) - Drilling speed adjustment from the panel control - Strengthened steel structures for tilting of the boring group - 1 motor HP. 2 (Kw 1,50) - Start/stop electropneumatic circuit by mean ...

Semi-automatic boring machine Brand: VITAP Typ: ALFA 35 T New machine Technical data: - One boring head 35 spindles - QUICK CHANGE SPINDLES - Pneumatic cylinder for horizontal/vertical positioning of the boring group (45 degreese and any intermediate angles) - Frontal/top 51aliper to obtain the same boring measure between horizontal and vertical position - Tilting side stops adjustable by metric scale and nonius and magnifying lens on each stop - 2 safety clamps inclined 4 degrees - Height regulation of the boring group by mechanical digital position indicator - Stroke regulation by means of 6 positions revolver (turret) (0-80 mm) - Automatic vertical-horizontal depth difference device (10 mm) - Speed regulation of the boring group command by control board - Strengthened steel structures for tilting of the boring group - 1 motor HP. 3 (Kw 2,2) - Sta ...