6300 v used for sale

Vacuum lifting device for paper rolls NAGRON AEROLIFTVacuum lifter for the paper industryWoudenberg Holland type R96-20Fabr. No. 9745 Year of construction 1999Load capacity 2000 kgCentering mandrel 90 mmSuction surface Outer diameter 850 mm (plus seal)Suction surface Inner diameter 250 mm (minus seal)Sealing width 50 mmSuction surface 0.5 m2Vacuum min. -800 mbarPumping speed approx. 100 m³/h per vacuum pumpMotor power 2x 2.2 kWNet connection 400 Volts, 50 Hz- 2 pieces Rietschle

Vertical CNC centre lathe, uses / outdated machine type: Emag VSC 200 control: Siemens 840 C construction year: From the in 1995 to the in 2007 overtakes TECHNICAL DATA: speed area / speeds: [1 / min].: 6,000 Drehmoment:/torque [Nm]: 480 Max dreh-? over bed swing diam .: 290 mms impulse achievement / power: [kW] 34 feed ? / chuck diam. 200 mms revolver / turret: 12-fold, VDI 40, shoemaker powered work witness / driven tools 7.8 kW Verfahrwege: X axis / x-travel: 550 mms Z-Achse/z-travel: 200 mms express way / rapidly travel: (X/Z) [m / min] 30 / 20 prepush / feeds: (X/Z) [m / min]. 11 KN connected load: [KW] 36 kW machine weight: [kg] 6,500 equipment signs: filings sponsor / chip conveyor, crowd

Sisu/Valmet Engine Type=612DSE,135KW,new factory repair Replacement motor with starter+alternator,new,TOP condition 1 year warranty ! email=info@miw-zeven.de

Valmet/Sisu Engine Type=612 DSE-135KW, Factory Repaired Engine with starter+alternator.New TOP-MOTOR ! info@miw-zeven.de

MATEC easily from our own development and production running lightly and quietly and transport bulk material and individual loads up to 250 kg with minimal energy over long distances up to 12 m at a time with a hand drill 300 w power consumption. The combined forced - and promotion of resonance stores the kinetic energy in the spring and must compensate for only the frictional resistance of the material. Sawdust, shavings, gravel, Earth, grain, hay and grass, etc. are exactly same speed transported with approximately 17 m / min. by means of Frequenzumforner the speed can be adjusted. The transport and screening in a single operation with a built-in sieve base perforation on request MATEC Vibrorinne standard Trough width inner 500 mm Trough height inner 260 mm current trough length 2500 mm (can front and rear to 1.5 m be extended without additional support) In addition current ...

Pneumatic valve DN 300 Manufacturer: Jaudt Dosiertechnik Maschinenfabrik GmbH Type: Varioschieber FSV Opening width mm: ø 350 Height mm: 130 Max.Working temp. ° C: 80 Operating pressure MPa: 0.6-1.0 maximum operating pressure MPa: 0 Control voltage V: -. Housing: one-piece cast housing in flange version the round face with coarse good Chicane Sealing: slide sheet implementation for with Adjustable stuffing seal Pressure piece from cast aluminium alloy Blade: Stainless steel 1.4301 Slide sheet: eccentric screws galvanized Finish: Stainless steel and aluminum parts blank Grey cast iron housing painted in RAL 9006 Steel parts zinc plated, 10 & #956; m Plate made of aluminium Housing material: Cast aluminium alloy (AlSi 10 mg) shock-proof up to 5 bar Flanschbohrbild: According to DIN 2501 PN 6 Packing material: ARAMIDE (Tmax 280 ° C) Operation: pneu ...

Volvo-Penta AD41A/B heat exchanger cpl.overtakes. info@miw-zeven.de

Stacking mass (LxWxH)- 16m x 1.4m x 1.6m fully automatic drying via computer Heating capacity - 90 kW Top Condition

Stack dimensions (LxWxH) - 16m x 1,4 m x 1,6 m automatic drying by means of computer Heating power - 90 kW Top Condition

VHM shank cutter from Garant (20 3160 - 20) lightly used, DIN 6527, type N, D= 20 mm number of teeth - 8, ask also for other quantities from the cutters. Price for 10 pieces 240,-€ for 1 piece 25,- €

Manufacturer: Nagema . fountain pen Varifill 110/15 regulation: Glass. construction year: In 1995 Type: Monoblok 110/15 technical data: To -110 filling valves to-15-figure Kronenkorker - run direction: left on the right -Doppel-Evakuierung control: Siemens S5

; ready for operation

Mixproof valve DN80, with welded valvehousing and balanced bottom channel. 3 pieces available Yom 2006, excellent condition.

COAX valve, see picture attached

The steam humidifier Defensor Mk5 is a pressure steam generator. It works on the principle of resistance heating. It is designed to directly (with ventilation) and indirect (corded steam distribution) humidifying of the air in conjunction with ventilation systems and air conditioning. Parameter Air Fan: Voltage: 200-240 V 50/60 Hz power consumption = U: P 26 W = maximum steam output: 16.0 kg / h Parameter MK5 Visual VE 8: 400V/3/50-60Hz, 6.1 kW

Vacuum filler Robby, filling, portioning, linking, pc control. The machine is currently in the refurbishing and can be tested in Koblenz, Germany.

5.8 m3/h 0.25 kW

Vortex Flowmeter 8800, F020SD1N3D1I1M5, Rosemount, EEx, new Manufacturer: Rosemount Type: Vortex 8800, F020SD1N3D1I1M5 Ex protected Attention! We have set the lowest price for the new part on the market. We still have several identical and other such devices, but the amount is ending. Buy more than 1 piece, there is still a great discount. Mint condition! The part was bought from a spare parts warehouse of a company, has never been in operation, is in a completely mint condition, but not in the original packaging. Function guarantee! For second hand parts, we can not accept any conventional guarantee and warranty. Since we know that the device works, we give you a functional guarantee when you buy it. If the device does not work within 6 months after purchase you can return the goods and we will refund the purchase price.

for pipeline DN 200

Half Round Slicer (Staylog) Manufactured by Valette&Garreau Model: STL-33

Stainless steel pipe screw with 250 mm diameter and 2,100 mm conveyor length (measured from mid inlet to middle outlet), inlet and outlet 270 mm each, with drive via intermediate gearbox and claw coupling.

Wartsila VASA V32 spare parts and complete engine also. 1.Reusable Liners wear below 0.30mm – free from crack, welding or any damages:8-10 2.Reusable Cyl heads bare – pressure tested free from crack:8-10 3.Piston with groove with in limit:8-10 4.Con rod – free from crack, wear within limit:8-10 5.Fuel pump - good condition:8-10 6.Centrifugal filter-good condition:1 7.Water pump – good condition:1 8.Lube oil pump - good condition:1 9.Turbo charger 354-11- good condition:2 10.Cam shaft – 12v32 A BANK & B BANK-good condition:2 11.WOODWARD 723 card - good condition:2 12.12v32 engine block - good condition:1 13.CAM SHAFT gear & CRANKSHAFT GEAR- good condition:2 14.FLY WHEEL- good condition 12V32:1 15.AFTER COOLER - good condition 12V32:1 If you are interested in complete engine part, please inform accordingly. For your information in past, we have supplied Engine  ...

Sugden Engineering Twin propeller Mixing Vessel. 200 L Stainless vessel, 2 top mounted paddle stirrers, Vessel 45 degree sloped base to outlet.

Vacuum filling machine Vemag Robby, filling, portioning, linking, pc control. The vacuum filler is currently in the refurbishment and you are very welcome to test the machine in Koblenz, Germany.

The vertical milling center FADAL VMC 2216 FX was manufactured in 2007 by the FADAL concern in the USA. The machine is equipped with FANUC Oi-MC numerical control. The milling machine can process workpieces weighing up to 450 kilograms. Machine travels in the X, Y, Z axes are 550 mm, 400 mm and 500 mm, respectively. The spindle revolutions of the CNC milling machine reach 8000 rpm. The center has a warehouse for 21 tools. Perfect for working with single details as well as for larger-scale processing. Technical data of the FADAL VMC 2216 FX machining center - CNC control: FANUC Oi-MC - table length: 406 mm - table width: 990 mm - maximum weight of the workpiece: 450 kg - X axis travel: 550 mm - Y axis travel: 400 mm - Z axis travel: 500 mm - maximum spindle speed: 8000 rpm - tool magazine: 21 - handle: SK 40 - spindle motor power: 11.2 kW - power demand: 35 kVA - power o ...

The vertical milling center FADAL VMC 15XTL was manufactured in 2007 in the United States by the FADAL brand. The machining center is digitally controlled by Fadal. It has a table size of 870 x 400 mm. The milling machine is designed for processing materials weighing up to 340 kg. It is equipped with a magazine for 21 tools. The spindle speed of the machining center, on the other hand, reaches 7500 rpm. Technical parameters of the FADAL VMC 15XTL CNC milling machine - CNC control: Fadal - working table length: 400 mm - working table width: 870 mm - maximum table load (evenly distributed): 340 kg - number of tools in the magazine: 21 pcs. - spindle drive power: 5.6 kW - maximum rotary speed of the vertical spindle: 7500 1 / min. - minimum distance between the spindle and the table: 101.6 mm - maximum distance between the spindle and the table: 609.6 mm - travel length in th ...

0: 200 °C Torque: - 0 Dimensions (HxWxD): 680 x 1320 x 760 mm weight: 177 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Type TP4 Spindle rotation speeds 20 000 U/Min/rpm Table dimensions 900x770 mm Weight 800 kg Transport dimensions 1800 x1000x1000mm

BARATTI FRAMED VACUUM PUMP WITH SUCTION FILTER AND SILENCER Fabr. -No.: 216 105 // Type: ATMOS V4-KR Var. 0102 Equipment / Additional information: Roots Blower Section. oil and wear-free compression, air-cooled, V-belt drive with tension rails and belt guard and two-stage exhaust silencer Incl. the following accessories: -Vacuum relief valve -saugs. Fine filter 3" -Connection piece internal thread 3" - Rohrfederman. -1..0 bar, filled with glycerine -Drive motor Blower data: Max. negative pressure: 500 mbar, abs. Suction volume: 440 m3/h Fan speed: 2920 rpm Noise level: approx. 79 dB (A) Engine data: 7.5 kW, 2930 rpm, 400/690 V, 50 Hz, IP 55 ISO class F, B3, KKL

Vakona ESK 125 Tumbler, vacuum mixing and tumbling machine, the machine comes with tumbling arm and mixing arm, container size 125 liters, MC control, direct cooling by strong cooling unit, mixing and kneading, all stainless steel. You are very welcome to inspect and test the machine in our facility in Koblenz, Germany.

Height 2130 Width 1410 mm Length 2130 mm Weight 1500 kg Capacity 1200 l Voltage Electrical: 400V 50Hz 3N Installed Power 9.1 kw Main material Stainlees Steel Load 1000 kg Mixing System Spiral With Paddles Product discharge Pneumatic dampers, front Mixer type Vacuum Mixer Shafts amount Double Shaft

Nadelstrukturierer Votan G08 Jenoptik mechanical Ritzer 2012 the Votan again for 160.000,00 euros on the new glass substrates and latest requirements was converted and was no longer in use. Complete unit incl 2 x belt transport table, suction, control Built in 2005 Shipping: 400,00 € (weight ca. 4500 kg)

K+G Wetter vacuum Cutmix 120 STL, model VCM 120 ,120 liters vacuum cutter, variable knife sdpeed, 2 bowl speeds, mixing speed forward and reverse, variable bowl speed, unloader manually operated, hydrlauic unloading device, knife cover electrically operated, with cooking facility. Further Information on demand. You are very welcome to test the machine in our facility in Koblenz, Germany.

Vemag Robot 500 vacuum filling machine / dough portioner, double screw System, for filling, portioning, linking, microcomputer control, filling capacity up to 2,500 kg/h You are very welcome to test the machine in our facility in Koblenz, Germany.

Kilia vacuum bowl cutter, 200 liters bowl cutter, bowl and bowl-cover stainless steel, hydraulic noise reduction cover, knife shaft brake electrically operated, membrane keyboard, variable knife speed, knife head, hydraulic loading device, hydraulic unloader

Status: New Manufacturer: Pfeiffer Type: TMH 064 Mod.-Nr.: PM P02 366 Remark To operateonly with appropriate pre pump and control. delivery time: on request; ready for use

Different gutter ca 150st with and without sieve occupy 800x400mm MVC 50-3 1100x300mm MVC 50-3 1100x400mm MVC 50-3 1100x500mm MVE 50-3 1200x400mm MVD 50-4 with and without sieve 1200x800mm MV 100/50 1200x1000mm MA 220 1200x1500mm Vem 8 1250x400mm MVD 50-3.1 Sieve 1300x1200mm MA 220 1400x650mm MVES 50-1P 1400x800mm MV 100/50 1400x1100mm MA 440 1450x900mm MVES 50-1P 1450x1200mm MVFS 50-2P 1500x400mm MVE 50-3 1500x500mm MS 7.21 Sieve 1500x650mm MVE 50-3.1 1500x800mm MVE 50 1600x400mm MVD 50-2 1600x900mm MVES 50-1P 1600x1200mm MA440 1750x400mm MVD 50-2 1800x500mm MVE 33-1 1800x1400mm MV 900-5 1850x500 MVES 50-1p sieve 1900x900mm MVF 33-1 2000x400mm MVF 50-1 2250x400mm MVE 50-3.1 3350x400mm 2x MVD 50-2 3500x2000mm 2x Schenck DF3 7400x950mm DMW 1000v 7500x500mm 2 Jost ruttler 7500x750mm DF3

RS Simulators Here we offer a temperature test chamber. Water cooling Temperature range: -45°C to +180°C External dimensions: width 1300 mm x height 2100 mm x depth 2250 mm Test area dimensions: width 840 mm x height 840 mm x depth 840 mm Aggregate part : width 2300 mm x height 2000 mm x depth 1300 mm Average heating speed: approx. 3 K/min Average cooling rate: approx. 2 K/min Power consumption: 15 A Connection voltage: 3x400V/N/PE 50Hz Weight: approx. 1000 kg Type: VTS 600/45 RS Refrigerant: R452 Zustand: gebraucht / used Scope of delivery: (see picture) (Changes and errors in the technical data, information is reserved!) We will be happy to answer any further questions you may have on the phone.

; ready for operation

Working width: 4800 mm N. of heated sections: 22 N of decks: 6 complete with automatic loading and un loding systems

Vacuum pump oil Fomblin (Perfluoro Polyether) Model: YL VAC 16/6 Quantity: 1 KG corresponds to approx. 0.5L Delivery time: ex stock Alternative: Model: YL VAC 25/6 Quantity: 1 KG corresponds to approx. 0.5L Delivery time: from stock; ready for use

Vacuum chamber with control and pump unit. diameter inside: 1000 mm Laenge inside: 1600mm vacuum pump: 1000m3/h Prated leakrate! Different vacuum chambers available as well as different constellations with pumps possible.

Used packaging machine by Variovac, type Optimus. New 2008. The VARIOVAC Optimus allows you to enter the field of economical and automated packaging of food, non-food and medical products. Whether you want to vacuum pack, protective atmosphere pack, SKIN pack, shrink pack or fill with hot products - the Optimus excels in all areas. With compact dimensions from 3m in length, it ensures reliable and efficient quality packaging! In its range of technology and performance, it sets the standard. Like all other VARIOVAC machines, Optimus uses the highly efficient VARIOVAC RapidAirSystem. Connection values: - Mains voltage 230/400 V, - Current consumption 21 A, - 12 kW power, - Frequency 50 Hz, - Control voltage 24 V, - Mains protection 32 A. Technical data: - Stroke mechanism: Pneumatic, - Protection class: IP 54, - Weight: 900 kg, - Noise level: 66 dB, - Vacuum pump: 10 ...

Vacuum - Measuring device CVC 2 Manufacturer: Vacuubrand Type : CVC 2 II Cat No. 24411004 Status: proven & functional Zubehoer : User manual Optinal: Power cable Measuring connection cable Delivery time: reserved from stock

Krings Verbau various base plates with mounting plate dimensions, spindles, etc. in the package or individually for sale Mass and guide can be requested to e-mail Price VB

Control SIEMENS Sinumerik 840D Specifications: Workspace - Max. rotation and turning diameter 2,000 mm - Max. turning height 2,000 mm - Face plate diameter 1,600 mm - Max. face plate load 11,200 kg - Chisel slide travel (vertical) 1,400 mm Smallest plunger diameter 330 mm Plunger cross-section 250 x 210 mm - Drive power of the main motor 71 kW - Crossbar adjustment 1,170 mm - Crossbeam support of central face plate to the right 1,170 mm - From the middle of the face plate to the left 25 mm Speed of faceplate: - Number of transmission stages 2 - 1 level 3.15-80 min-1 - 2 Level 12.5-315 min-1 - Lifter and support hydrostatically guided Feeds - X and Z 0.1 2000 mm/min - Rapid traverse X and Z 6,000 mm/min - Weight approx. 24,000 kg - Voltage 400 V 50 Hz - Connected load 175 kW - Space requirement L = 10,000 mm B = ...

Table size: 410 x 900 Traverse path x/y/z: 560/410/380 mm spindle retainer: SK 40 spindle speeds: 22-6000 rpm feeds: x & z to 10000, y up to 240 mm / min space: 2600 x 2000 x 2300 mm weight: 3500 kg

Nominal Rating 1000 l/h; prepared - top condition

Pump: centrifugal pump Manufacturer: Varisco Type: J40/J1-110 Year of construction: 2002 Capacity: 10 m3 / 13m / - 20 m3 Engine: Siemens KW: 1.1 Voltage: 380 V Speed: 2850 RPM Connection inlet DN 40 Port side: DN 40 Machine number: 107921 Dimensions: length 700 mm Product-contacting parts: stainless steel