4 side used for sale

Pressure total: 140 ton Stroke: 800 mm Daylight: 1.004 mm Free frontal opening L-R: 2.060 mm Table surface area : 2.000 x 520 mm Slide area: 2.040 x 520 mm Working speed: 4 -20 mm / sec Rapid travel: 135 mm / sec Return speed: 120 mm / sec Weight of machine approx.: 14 ton Height over floor approx.: 4.810 mm Oil volume: 700 l

Very high-quality BMW R 75/5 motorcycle sidecar in classic black paint with white trim lines. The vehicle was fully restored between 2010 and 2012 and has only driven about 680 km since then. The restoration and conversion costs were over 26,000 € without the motorcycle. The vehicle comes with a complete Leitz folder with extensive documentation. The sidecar was built in 2012 as a new part, regularly accepted and registered. Visually, the combination presents itself in a very neat condition with a clean paintwork, neat chrome, wire wheels, classic boxer technology and a harmonious overall look. Equipment: · Registered sidecar · Sidecar with disc brake · Wire rims · Large lockable trunk in the sidecar · Comfortable sidecar seat with good legroom · Full restoration 2010–2012 · Extensive documentation folder · Classic BMW 2-cylinder boxer engine · Shaft drive · Black paint wi ...

Pressure total: 1400 ton Stroke: 950 mm Daylight: 2000 mm Table surface area : 3600 x 2500 mm Slide area: 3600 x 2500 mm Die cushion capacity in table: 400 ton Die cushion stroke: 500 mm Die cushion pad area: 3060 x 1860 mm Approach speed: 400 mm / sec Working speed: 40 / 80 mm / sec Return speed: 400 mm / sec Oil volume: 5000 l Required power: 450 kW Weight of machine approx.: 240 ton

Pressure total: 500 ton Stroke: 1100 mm Daylight: 1500 mm Table surface area : 2000 x 1250 mm Slide area: 2000 x 1250 mm Die cushion capacity in table: 160 ton Die cushion stroke: 300 mm Approach speed: 650 mm / sec Required power: 55 kW Weight of machine approx.: 50 ton

used side feeder for foil snippets / scrap Centrifuge with drive and feed container this unit was mounted on a 150 mm extruder Capacity over 320 kg/h

Manufacturer: HolzHer, Type: 1444, Year: 1991, Min-max feed m/min: 10 - 20, Premilling: yes, Coil magazine: yes, Strip magazin: no, Mitre stations: yes, Bevel milling: yes, Corner tracing type: no, Top pressure belt/roller: Rolle, Year :1991

Manufacturer: KDP Kantenanleimmaschine, Type: KDP 111 SL, Year: 1995, Min-max edge material mm: 0,5-2,0, Work piece width min-max mm: 60, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 10-45, Min-max feed m/min: 8, Lasertechnik: yes, Mitre stations: yes, Radius milling axis adjustment: no, Year :1995

Manufacturer: IMA Steckprofileindrückmaschine, Type: Nowimat/I/G80/500, Year: 2001, Control: Ima, Work piece width min-max mm: ca.60, Min.-max. workpiece length in mm: 2500, Min.-max. workpiece height in mm: 10-45, Min-max feed m/min: ca.20, automatischer Einzug: yes, Premilling: 4 X 2,2 kw, Coil magazine: 2 Stück Stegprofil, Mitre stations: yes, radius milling: Eindrückstation Profil, Work piece refeeding: yes, Hover cussion table: yes, Hover cussion table: yes, Year :2001

Manufacturer: Sicar, Type: P5N/230, Year: 1989, Control: yes, Planing widht mm: 230, Planing hight mm: ca.130, Number of spindles: 5, Rotations of spindles max. rpm: 6000, Separate engine per spindle: yes, Feeding - kW: 1,5, 1.Bottom spindle kW: 5,5, 2nd spindle on right kW: 5,5, 3.Left spindle kW: 5,5, 4.Top spindle kW: 7,5, 7th universal on left kW: 5,5, Year :1989

450-550mm

Manufacturer: Weinig, Type: H 17 AS, Year: 1986, Planing widht mm: 230, Number of spindles: 9, Tool exchange places: yes, Separate engine per spindle: yes, Feeding - kW: 11, Feeding speed min-max m/min: 60, Feeding speed continous adjustable: yes, Table length: ca. 4000 mm, 1.Bottom spindle kW: 4, 2nd spindle on right kW: 4, 3.Left spindle kW: 5,5, 4th spindle on right kW: 4, 5.Top spindle kW: 7,5, 6th spindle at bottom kW: 5,5, 8th spindle at bottom kW: 7, 8th spindle on left kW: 4, 10th universal on left kW: 5,5, FREE TEXT: Inverter for feeding., Year :1986

Manufacturer: IMA, Type: Advantage 8200, Year: 2003, Min-max edge material mm: 0,4-20, Work piece width min-max mm: min. 60, Min.-max. workpiece length in mm: min. 150, Min.-max. workpiece height in mm: 10-60, Min-max feed m/min: 4-20, Premilling: yes, Mitre stations: yes, Radius scraper: yes, Flat scraper: yes, Profile sanding top bottom: yes, Weight approx. kg: 4400, Year :2003

Manufacturer: Homag, Type: KLO 76, Year: 1994, Min-max edge material mm: 0,5-3,0, Min.-max. workpiece length in mm: 150, Edgeband height max mm: 55, Min-max feed m/min: 10-25, Premilling: no, IR zone: yes, Strip magazin: yes, Min.-max. batten magazine mm: yes, Mitre stations: yes, radius milling: yes, 4 motors: yes, Radius scraper: yes, Flat scraper: yes, 4 motors: yes, Ersatzverleimteil : yes, Bonding part EVA: yes, Pre-smelting Kg/Hr: yes, Buffing unit: yes, Top pressure belt/roller: yes, Roller/belt: Riemen, Compressed air bar: 6, Machine lenght mm: 7500, Noise enclosure: yes, Year :1994

Manufacturer: Weinig, Type: Unimat 17, Planing widht mm: 170, Planing hight mm: 120, Spindle diameter in mm: 35, Rotations of spindles max. rpm: 6.000, Spindle arrangement: U / R / L / R / O / U, Feeding - kW: 4, 1.Bottom spindle kW: 4, 3.Left spindle kW: 3, 4th spindle on right kW: 3, 5.Top spindle kW: 4, 6th spindle at bottom kW: 4,

Manufacturer: Ott, Type: F 2530, Year: 2008, Min-max edge material mm: 0,2-25, Work piece width min-max mm: min. 65, Min.-max. workpiece length in mm: min. 150, Min.-max. workpiece height in mm: 8-60, Min-max feed m/min: 10-16, Premilling: yes, Mitre stations: yes, 2 motors: yes, Type of scraper: Profil und flatch, Flat scraper: yes, Year :2008

Manufacturer: IMA, Type: Man.Kantenanleimer HKA, Min-max edge material mm: 0,4-3, Work piece width min-max mm: 100, Min.-max. workpiece length in mm: 100, Edgeband height max mm: 16-45, Min-max feed m/min: 0,7-1,2,

Manufacturer: Weinig, Type: Unimat 17, Planing widht mm: 180, Planing hight mm: 120, Number of spindles: 7, Elektronische Achsverstellung: no, Work piece width min-max mm: 180, Min.-max. workpiece length in mm: 350, Wellendrehzahl: 6000, Spindles: 6, Spindle diameter in mm: ca 40, Spindle arrangement: U / R / L /R / O / U / Uni, 1.Bottom spindle kW: 4, 2nd spindle on right kW: 4, 3.Left spindle kW: 4, 4th spindle on right kW: 4, 5.Top spindle kW: 4, 6th spindle at bottom kW: 4, 7th universal on left kW: 4,

Manufacturer: Ilcam Kantenbearbeitung, Year: ca.1990, Monting of the machine: Verleimteil/Kappen/Vorfräsen/Zieklinge, Min-max edge material mm: 0,5-12, Work piece width min-max mm: 65, Min.-max. workpiece height in mm: 10-55, Min-max feed m/min: 10-20, Premilling: no, Fine milling: yes, Strip magazin: yes, Min.-max. batten magazine mm: yes, Mitre stations: yes, Pre-milling: yes, Bevel milling: yes, Radius scraper: yes, Year :ca.1990

Sanding diameter: 1000mm, Table tilted adjustable.

Manufacturer: Brandt , Type: KD 79/2 CF, Year: 2002, Min-max edge material mm: 0,5-3,0, Min-max feed m/min: 18, Axis control: no, Premilling: yes, Fine milling: yes, Application of separation agent: no, IR zone: no, Coil magazine: yes, Strip magazin: yes, Min.-max. batten magazine mm: yes, Mitre stations: yes, Pre-milling: yes, Bevel milling: yes, 2 motors: yes, Radius scraper: yes, Flat scraper: yes, Bonding part EVA: yes, Buffing unit: yes, Top pressure belt/roller: Rolle, Work piece refeeding: yes, Year :2002

Manufacturer: IMA, Type: Man.Kantenanleimer HKA, Min-max edge material mm: 0,4-3, Work piece width min-max mm: 100, Min.-max. workpiece length in mm: 100, Edgeband height max mm: 16-45, Min-max feed m/min: 0,7-1,2,

Manufacturer: Felder, Type: MG 580-1, Year: 2012, Control: yes, Min-max edge material mm: 0,4-5, Work piece width min-max mm: min. 70, Min.-max. workpiece length in mm: min. 140, Min.-max. workpiece height in mm: 8-60, Min-max feed m/min: 11, Premilling: yes, Mitre stations: yes, Weight approx. kg: 990, Year :2012

Manufacturer: SCM, Type: P64, Year: 1988, Planing widht mm: 180, Planing hight mm: 105, Number of spindles: 4, Rotations of spindles max. rpm: 6000, Separate engine per spindle: no, Main engine kW: 4, Fully suspended drive feeding: yes, Feeding - kW: 2,5, Feeding speed continous adjustable: yes, Tischlänge mm: 2000, Adjustment - electonically: no, Noise enclosure: yes, Compressed air bar: yes, Wight approx. kg: 2000, Year :1988

Manufacturer: IMA, Type: Man.Kantenanleimer HKA, Year: 2000, Min-max edge material mm: 0,4-3, Work piece width min-max mm: 100, Min.-max. workpiece length in mm: 100, Edgeband height max mm: 16-45, Min-max feed m/min: 0,7-1,2, Year :2000

Manufacturer: Ziwo, Type: CL 11.10, Year: 1996, Work piece width min-max mm: 0 - 300, Min.-max. workpiece length in mm: 200, Min.-max. workpiece height in mm: 5 - 150, Wight approx. kg: 210, FREE TEXT: Beschickung, Year :1996

Manufacturer: IMA, Type: Compact F 12, Year: 1996, Control: Beckhoff, Min-max edge material mm: 0,5-3,0, Work piece width min-max mm: 65, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 10-50, Min-max feed m/min: 18, Infeed table: yes, Premilling: yes, Coil magazine: yes, Strip magazin: yes, Min.-max. batten magazine mm: yes, Mitre stations: yes, Pre-milling: yes, Corner tracing type: yes, 4 motors: yes, 4 motors: yes, Bonding part EVA: yes, Pre-smelting Kg/Hr: yes, Year :1996

Manufacturer: Homag, Type: FKR 78/C/A/S3, Monting of the machine: zerspanerteil zum Einkürzen, Min-max edge material mm: 0,5-3,0, Work piece width min-max mm: 60, Min.-max. workpiece length in mm: 250, Min.-max. workpiece height in mm: 10-40, Min-max feed m/min: ca.18, Infeed table: yes, Premilling: yes, Fine milling: yes, Mitre stations: yes, Pre-milling: yes, Bevel milling: yes, Radius scraper: yes, Flat scraper: yes, Bonding part EVA: yes, Work piece refeeding: Bargstedt, Roller/belt: Riemen, Compressed air bar: 6, Return type: Bargstedt TFU,

Manufacturer: Homag , Type: KAL 310/8/A20/S2, Year: 2005, Control: PC 22, Work piece width min-max mm: min 55/100, Min.-max. workpiece height in mm: 12 - 60, Min-max feed m/min: 18 - 24, Einlauflineal gesteuert: yes, Premilling: 2 x 3kW, Application of separation agent: yes, Coil magazine: 2, Mitre stations: Fase / Gerade, Pre-milling: 2 x 1,5 kW, Bevel milling: FK 13 - 8Fach, radius milling: 4 kW, Corner tracing type: MN 21, Flat scraper: FA 11, Bonding part EVA: A 20, Top pressure belt/roller: Band, Work piece refeeding: vorinstalliert, FREE TEXT: Frreiplatz, Year :2005

Manufacturer: Hebrock, Type: AKV 2001 DK, Year: 1997, Min-max edge material mm: 0,5-3,0, Work piece width min-max mm: 60, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 10-45, Min-max feed m/min: 8, Coil magazine: yes, Strip magazin: no, Mitre stations: yes, Pre-milling: Radius, Corner tracing type: yes, 1 motor: yes, Radius scraper: yes, Bonding part EVA: yes, FREE TEXT: Zustand sehr gut, Year :1997

Manufacturer: Brandt, Type: KS 23, Year: 1988, Min-max edge material mm: 0,5-12, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 10-50, Edgeband height max mm: 55, Min-max feed m/min: 12, Premilling: no, Coil magazine: yes, Strip magazin: yes, Min.-max. batten magazine mm: yes, Mitre stations: yes, Bevel milling: yes, Corner tracing type: no, Radius scraper: yes, Flat scraper: yes, Bonding part EVA: yes, Edge sanding: yes, Year :1988

Manufacturer: Brandt, Type: KD 99, Year: 1998, Control: Homatic, Min-max edge material mm: 0,4 - 3,0, Work piece width min-max mm: 62, Min.-max. workpiece length in mm: 160, Min.-max. workpiece height in mm: 60, Edgeband height max mm: 62, Premilling: yes, Bevel milling: yes, Corner tracing type: yes, 4 Motoren: yes, Nuten : yes, Radius scraper: yes, 4 Motoren: yes, Compressed air bar: 6, Machine lenght mm: 8740, Noise enclosure: yes, Rückführung Typ: yes, machine ready for demonstration: yes, Year :1998

Manufacturer: Brandt , Type: KS 25, Year: 1991, Min-max edge material mm: 0,5-3,0, Work piece width min-max mm: 60, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 10-50, Edgeband height max mm: 55, Min-max feed m/min: 14, Premilling: no, Mitre stations: yes, Pre-milling: yes, Bevel milling: yes, Flat scraper: yes, Bonding part EVA: yes, Top pressure belt/roller: Rolle, Werkstückunterstützung: yes, Freiplätze: keine, Year :1991

Manufacturer: Weinig , Type: Unimat 17 A, Year: 1979, Control: hand, Planing widht mm: 10-170, Planing hight mm: 10-120, Min.-max. workpiece length in mm: 300, Number of spindles: 6, Diameter of the spindle mm: 30, Fast exchange device: no, Rotations of spindles max. rpm: 6000, Separate engine per spindle: yes, Fully suspended drive feeding: no, Year :1979

Manufacturer: Koch, Type: SBD - 320 , Year: 1994, Control: Programm, Working widht max mm: 1500, Arbeitstiefe max mm: 320, Working thickness max mm: 10 - 32, Saw diameter mm: 350, Work piece transport: Kette, Drilling support horizontal: 2, Drill gearings: 7, Drill gearings: 7, Drill support from top: 5, Drill gearings: 7, Belt conveyor: yes, Gluing: yes, Re-charging: no, Dovel insertion: yes, Raster 32 mm: yes, Horizontal drilling from both sides: yes, Wight approx. kg: 6000, Year :1994

Manufacturer: Biesse , Type: Stream B1 S3, Year: 2005, Control: NC 1600, Min-max edge material mm: 20, Work piece width min-max mm: 65, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 60, Min-max feed m/min: 25, Min.-max. batten magazine mm: 20, Bevel milling: yes, radius milling: yes, Radius scraper: yes, Buffing unit: yes, Year :2005

Manufacturer: Ott, Type: Euromatic FÜ, Year: 2001, Program: yes, Control: SPS, Work piece width min-max mm: 60 , Min.-max. workpiece length in mm: 60, Min.-max. workpiece height in mm: 10 - 60, Kantenmaterial min-max mm: 0,2 - 15, Vorschub min- max m/min: 12 - 20, Mitre stations: yes, Fasefräsen: yes, Flat scraper: yes, Rolle/Riemen: Rollen, Machine lenght mm: 8500, Wight approx. kg: 4200, Year :2001

Manufacturer: Lange Kantenfräsgerät, Type: B 600, Year: 2009, Moulding spindles: 2, Routing: yes, Min.-max. workpiece length in mm: 8-60, Vorschub min- max m/min: Handvorschub, Mitre stations: yes, Mitre stations: yes, Radiusfräsen : 1,5 mm, FREE TEXT: Fräsmotore Frequenzgeregelt, Year :2009

Manufacturer: HolzHer, Type: 1411-1, Year: 2001, Work piece width min-max mm: 60, Min.-max. workpiece length in mm: 230, Edgeband height max mm: 50, Thickness of coiled edgeband max mm: 3, Vorschub min- max m/min: 11, Glue system granulate/cartridge: Patrone, Buffing unit: yes, Machine lenght mm: ca. 4.100, Wight approx. kg: ca. 1.100, Year :2001

Manufacturer: HolzHer, Type: Sprint 1310, Year: 2006, Edgeband height max mm: 45, Thickness of coiled edgeband max mm: 3, Vorschub min- max m/min: 10, Mitre stations: yes, Glue system granulate/cartridge: Patrone, Mitre stations: yes, Radiusfräsen : yes, Buffing unit: yes, Top pressure belt/roller: rolle, Compressed air bar: 6, Machine lenght mm: 3, Year :2006

Manufacturer: Koch, Type: Compact, Year: 1991, Control: Programm, Working widht max mm: 150-2500, Arbeitstiefe max mm: 200, Working thickness max mm: 80, Schwenkbereich Grad in X: +30-90, Dovel units: 3, Dovel diameter mm: 10-12, Drill gearings: 2, Drill gearings: 2, Drill gearings: 2, Drill spindles per support: 5, Gluing: yes, Dovel insertion: yes, Raster 32 mm: yes, Compressed air bar: 6, Wight approx. kg: 3000, Year :1991

Manufacturer: SCM, Type: P64, Year: 1988, Planing widht mm: 180, Planing hight mm: 105, Number of spindles: 4, Rotations of spindles max. rpm: 6000, Separate engine per spindle: no, Main engine kW: 4, Fully suspended drive feeding: yes, Feeding - kW: 2,5, Feeding speed continous adjustable: yes, Tischlänge mm: 2000, Adjustment - electonically: no, Noise enclosure: yes, Compressed air bar: yes, Wight approx. kg: 2000, Year :1988

Weinig Profimat 23E four-sided planer Working width 230mm Working height 120mm Number of spindles 6 Bottom 5.5kw Right 7.5kw Left Top 7.5kw Bottom 4kw Universal 7.5kw Spindle diameter 40mm Working speed 24m/min Pneumatic pulling roller clamps Electric pressure beam adjustment Tabletop lubrication system Year of production 1998

This grinder has 1 fixed blade and 3 rotating blades. The motor power is 2.2 kW. The grid is replaceable, so the grain size can be changed. Everything works perfectly, motor, bearings, rotor, knife are fine. It's ready to use. I have several of them. There are also other document shredders for sale. Please also see my other ads.

with packing device

Key data: 5 , 260 mm, 160 mm

Number of Spindles: 5 Spindle arrangement: u-r-l-o-u Diameter of the spindles: 40 mm Spindle speed: 6000 rpm Working width adjustment: digital Working height adjustment: digital Feed speed: 20 m/min Table height constant: approx. 800 mm Bevel units: 1 Diameter of the suction nozzles: 140 mm Weight: 2500 kg Space requirement: 3650x1500x2000 mm Voltage/Frequency: 380V

Key data: 4 , 23 mm, 10 mm

Exhibition machine! Working width (mm): 23 - 180 Minimum workpiece length (mm): 300 Feed speed (r/min): 6 - 12 Engine: Feed: 0.7/1.1 kW (1/1.5 HP); Horizontal spindle (single): 7.5 kW (10 hp); Vertical spindles (single): 7.5 kW (10 hp) Speed (r/min): 6000 Spindle ø (mm): 35 Feed table length (mm): 1700 Working height (mm): 10 - 105 Suction nozzle ø (mm): 120

Pressure total: 315 ton Stroke: 1100 mm Daylight: 2200 mm Table surface area : 2500 x 1000 mm Slide area: 2500 x 1000 mm Die weight at the ram max.: 6000 kg Approach speed: 600 mm / sec Working speed: 32 - 230 mm / sec Return speed: 600 mm / sec Required power: 158 kW Weight of machine approx.: 44 ton Height over floor approx.: 6175 mm

An all-terrain four-way sideloader Combilift is available. Fuel: LPG, load capacity: 6000kg, load center: 600mm, lift height: 5552mm, mast type: Triplex, overall height: 2845mm, free lift: 1600mm, fork: 1400mm, valves: 3, weight: approx. 9800kg, operating hours: 561h. Including fork positioner, heating, full cab and double gas bottle holder. Documentation available. On-site inspection is possible.

Key data: 5 , 120 mm, 230 mm

Planing and moulding machine Profimat 23 E Working width: 230 mm Working height: 120 mm Dressing table length: 2000 mm Spindle arrangement 1: Dressing 5.5 kW, 6000 rpm, 40 mm diameter 2+3 Left+ Right 7.5 kW, 6000 rpm, 40 mm diameter 4: Thickness 5.5kW, 6000rpm, 40mm diameter 5: Bottom 4kW, 6000rpm, 40mm diameter Feed motor: 2.2 kW Feed speed infinitely variable 0-24 m/min Milling heads with adjustment gauge Total power requirement: 27 kW Dimensions set-up: 3400 x 1650 x 1970 mm Machine weight, approx.: 3500 kg

Fully automatic paper labelling machine for applying labels on both sides (back and front). PLC controlled or touch switch knob control, photoelectric device (LEUZE sensor), variable speed motors and conveyor chain board. - Specification: label length: 10-250mm | label width: 10-150mm | bottle diameter: customized | label core diameter: 76mm. max. label roll diameter: 300 mm. Label precision: ? 1mm | max. speed of the machine in neutral: 150 cycles/minute | power: 220V/380V, 50Hz/60Hz, 750W | machine dimensions: L2400mm?W1500mm?H1400mm | weight: 400kg. Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo are po ...