130,800 used machines on RESALE, but how to find them? Machine Search
SHUZ TUNG CNC 50 BRM CNC tube and profile bending machine built in 2014 in Taiwan allows for fully automatic, serial production of complex spatial workpieces in 5 axes with simultaneous hole punching. Excellent precision and accuracy of bending are guaranteed by the reliable servo motors used in the machine, which are responsible for realising the main working movements, i.e. bending, rotation and material feed. The rest of the movements are driven by a central hydraulic system with electronic lubrication. The SHUZ TUNG CNC mandrel bending machine is operated via a control panel with an installed CNC controller with the option of saving an unlimited number of programmes. In addition, the automatic servo bending machine is equipped with several bending rolls, a high-quality mandrel and an actuator to support material feed. The 50 BRM automatic CNC mandrel bending machine weighs 3500 kg ...
Robust, high-quality round sheet bending machine for already profiled workpieces (sheet blades) - with motor drive at the bottom and top adjustable workpiece width between 300 mm and 800 mm, largest sheet thicknesses which can be bent round copper / titanium zinc / aluminium 0.8 mm - galvanized steel sheet 0.7 mm - stainless steel sheet 0.5 mm, smallest possible bending radius 350 mm - bending radius depending on the yield strength - smallest bending radius galvanized steel plate 0.7 mm - 1,000 mm, continuous speed infinitely adjustable 1 to 6 m/min, drive capacity 2 x 0.75 kW, weight 375 kg
Technical data: - bending and rolling by hand, - max working width 1020 mm - max. material thickness St 40 1.25 mm - Bending angle adjustment via end stop 10 - 180 ° - max hub upper cheek approx. 85 mm - max. adjustable bending cheek 20 mm - Shaft diameter 55 mm - Upper shaft can be swivelled - Rear shaft parallel + obliquely adjustable - Space requirement approx. W 1500 x H 1400 x D 750 mm - Weight approx. 400 kg
Press brake edge machine edge bench press used Manufacturer: Mengele Type: C320-4B Built: 1966 last revision and repair: 2000 Location D-01587 Riesa Dimensions WxH: 6,250 x 3,650 mm Edge knife width: 6,150 mm sheet thickness at 6,000 mm bending length: approx. 7.5 mm. The machines are designed for very deep shaft bends, therefore very deep cheek recesses. Original 300 t pressing force - In 1989 the pressing force was increased to 350 t. The press is in very good condition despite its age. The machine is disassembled and ready for loading. documentation for the machine is available. Weight: about 45 t
used
The HKB series swivel machines are used for bending thin sheet metal. Due to their compact design, they fit easily into small workshops and cover a wide range of applications with their segmented upper tool. With an adjustable angle stopper, these swivel machines are also suitable for the production of small batches. Compact and torsion-resistant Segmented upper tool for many bending options Integrated, manual bend compensation Adjustable angle stop for series production Hands free Foot control of the upper bolster clamp Workspace Working length 1270 mm Sheet thickness (max.) – 400 N/mm² 2 mm Dimensions (length x width x height) 1.6 m x 0.9 m x 1.18 m Weight 330 kg Angle range of the bending beam 135°
Mechanic plate bending machine Goyar 3C-25/20. Bending lenght: 2000mm. Bending capacity: 25mm. Diameter of upper cylinder: 285mm. Diameter of lower cylinders: 235mm. Main motor power: 20cv. Bending speed: 5 mpm. Weight: 5500Kgs.
Max Bending Length 2250mm Machine is in excellent condition - As New LOW HOURS
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation - automatic CNC – controlled double-sided pre-bending - Conical bending device - three hydraulically driven rollers (one hydraulic motor per roller) - hydraulic linear under-roll adjustment - hard chrome-plated piston rods - hardened and ground rollers - PILZ® laser protection - BECKHOFF® CNC control with Ethernet technology and large touch screen - DANFOSS® precision hydraulics - Central lubrication system
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic CNC – controlled double-sided pre-bending – conical bending device, three hydraulically driven rollers (one hydraulic motor per roll), hydraulic linear sub-roll adjustment – hard chrome-plated piston rods – hardened and ground rollers - PILZ® laser protection - BECKHOFF® CNC – control with Ethernet technology and large touch screen - DANFOSS® precision hydraulics – central lubrication system Maximum bending length 2,000 mm Roll diameter 170 mm Smallest weft diameter = 1.1 x the roll diameter The rollers run in bronze plain bearings. Nominal pre-bending performance over the entire bending length at 5 x D = 5 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 7 mm sheet steel/ST40 Drive power ...
Very high-quality CNC – controlled precision sheet metal round bending machine with automatic bending sequence calculation – automatic CNC – controlled double-sided pre-bending – conical bending device, three hydraulically driven rollers (one hydraulic motor per roll), hydraulic linear sub-roll adjustment – hard chrome-plated piston rods – hardened and ground rollers - PILZ® laser protection - BECKHOFF® CNC – control with Ethernet technology and large touch screen - DANFOSS® precision hydraulics – central lubrication system Maximum bending length 2,000 mm Roll diameter 170 mm Smallest weft diameter = 1.1 x the roll diameter The rollers run in bronze plain bearings. Nominal pre-bending performance over the entire bending length at 5 x D = 5 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 7 mm sheet steel/ST40 Drive ...
specifications: - Pressure capacity 100 KN / 10 t - Compressive force adjustable 0 - 100 kN - Stroke length 0 - 150 mm - Clear width approx. 200 mm - Lifting speed 0 - 0.6 m/min - Tool height up to approx. 100 mm - Bending performance - with prism MW 100 flat to approx. 100 x 12 mm - Tube bending up to approx. 1 inch - Directional power Wy at straightening block distance of 1m 100 cm³ - Drive 400 V / 1.1 kW - Space requirement approx. W 1100 x H 1000 x D 650 mm - Weight approx. 400 kg
sheet width: 1500 mm plate thickness: 1,5 mm distance between columns: 1500 mm bending angle max.: 135 ° total power requirement: - kW weight of the machine ca.: 0,36 t dimensions of the machine ca.: 1,7 x 0,7 x 1,3 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Specifications: 2 castors hydraulically adjustable 3 rollers driven Resistance torque: 80 cm³ Shaft diameter: 100 mm Roll diameter: 315 mm lateral hydr. Controlled arm correctors left and right CE. Mark Bending capacity square: 120 x 60 x 5 mm Bending capacity flat steel: 130 x 25 mm Bending capacity tube: 114.3 x 6 mm Bending power angle: 100 x 10 mm Round steel: 80 mm Motor power: 11 kW Control panel with digital display Dimensions (length x width x height): approx. 1750 x 1850 x 1650 mm Weight: approx. 3.6 tons Accessories: Various bending rollers Condition: we will still carry out a complete service on the machine The seller is not liable for typographical or data transmission errors. The machine is appropriate for its age in terms of appearance, technology and wear; used machines are sold without any warranty.
tube diameter: . mm wall strength: . mm bending radius min.: . mm Control: total power requirement: kW weight of the machine ca.: . t dimensions of the machine ca.: . m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW connected load: 400/50 V/Hz hydraulic pump: 1,1 kW : 80 kN range L-W-H: 900 x 600 x 1000 mm weight: 470 kg Equipment / Accessories: - Three driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 95 mm Shaft diameter: 30 mm Shaft revolutions: 7 U/min roll diameter: 132 mm Drive: 0,75 kW weight: 220 kg range L-W-H: 530x900x660 mm Equipment / Accessories: - Two driven rollers with grooved surface - Manual feed of the upper roller - working position horizontal and vertical (with tilting base) - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn different profiles are used e.g. Flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
round material: 40 mm tube diameter: 70x2 mm square material: 80x30x3 mm L-beam: 50 x 5 mm I - beam section - flat steel: 80 x 16 mm I-beam section - upend: 50 x 15 mm roll diameter: 157 mm Shaft diameter: 50 mm bending speed: 2,95 m/min total power requirement: 1,1 kW weight of the machine ca.: 500 kg dimensions of the machine ca.: 1000x950x1450 mm Domestic equipments: - Special steel shafts (42CrMo4) hardened and ground - a set of standard rollers - lower rollers up and down hydraulically deliverable - digital display for lower rollers - separate control panel - in one direction manually adjustable lateral straightening rollers - manual lubrication - horizontal and vertical operation - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW connected load: 400/50 V/Hz hydraulic pump: 1,1 kW : 80 kN range L-W-H: 900 x 600 x 1000 mm weight: 470 kg Equipment / Accessories: - Three driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1050 mm plate thickness: 1 mm roll diameter: 56 mm dimensions of the machine ca.: 1600 x 700 x 1050 mm Domestic equipments: - Upper roller can be swung out manually The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW connected load: 400/50 V/Hz hydraulic pump: 1,1 kW : 80 kN range L-W-H: 900 x 600 x 1000 mm weight: 470 kg Equipment / Accessories: - Two driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2100 mm plate thickness: 13 mm pre-bending: 10 mm upper roll diameter: 230 mm lower roll diameter: 210 mm side roll diameter: 190 mm total power requirement: 7,5 kW weight of the machine ca.: 4.620 kg dimensions of the machine ca.: 4150x1400x1300 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG ...
: 80 mm roll diameter: 260 mm : 7 U/min : 170 mm : 27 kN : 160 mm : 450 mm total power requirement: 3,7 kW dimensions: 980x1430x1600 mm weight: 1380 kg Accessories / equipment: - Three driven rollers with a smooth surface - Hydraulic delivery of the upper roller - Working position horizontal and vertical - Digital display with memory function - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can bend different profiles are used e.g. Flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: R10-R260 : 210 ° bending speed: 2 U/min : 1 1/4 x 3,5 mm : einphasig - 230 V drive motor: 1,1 kW : < 70 dB weight of the machine ca.: 80 kg dimensions of the machine ca.: 410 x 1000 x 570 mm Accessories / equipment: Hard copper and aluminum: 54x2 mm Steel tube: 42x3 mm Stainless steel: 42x2.5 mm Solid material: 30 mm Number of programs: 30 each 9 bends Control: Soft-touch control panel in 8 different languages Mobile by driving device The controller allows easy programming of the automatic cycle The controller is equipped with a system diagnostics and has a great language selection. Patented fast tool change system A single bending speed The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 48x3,5 mm : 48x2,5 mm : 32 mm : 64x2 mm bending speed: 2 U/min : R10-R300 total power requirement: 1,5 kW weight of the machine ca.: 110 kg dimensions of the machine ca.: 410x1000x570 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bar material - diameter: Ø 35 mm I-beam section - flat steel: 60x10 mm L-beam: 50 mm tube diameter max.: Ø 60x2 mm square material: 45x45x3 mm roll diam. toproll: 162 mm roll diam. bottom roll: 152 mm Shaft diameter: 50/40 mm turning speeds: 3,3 m/min total power requirement: 1,5 + 0,75 kW weight: 450 kg range L-W-H: 1050x950x1450 mm Domestic equipments: - hydr. Delivery of the top roller - standard roller set - side straightening rollers - Upper roll holder: 50.0 mm - Under roller diameter: 40.0 mm - Control panel The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 50 mm : 8,5 U/min : 100 kN roll diameter: 162 mm Drive: 1,5 kW range L-W-H: 1100x850x1350 mm weight: 495 kg Equipment / Accessories: - Two driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - Footswitch - standard roller set The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
L-beam: 50x5 mm square material: 50x40x3 mm I - beam section - flat steel: 120x15 mm I-beam section - upend: 60x10 mm round material: Ø 35 mm tube diameter: Ø 70x2 mm roll diameter: 155 mm bending speed: 4,3 m/min bore: 50 mm total power requirement: 1,5 kW weight: 400 kg dimensions: 830x730x1350 mm Domestic equipments: - Extended special steel shafts - a set of hardened rollers - Bottom rollers are driven - lateral straightening rollers - Foot pedal - horizontal and vertical working - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
I-beam section - flat steel: 80x20 (d1200) mm I-beam section - upend: 80x25 (d2100) mm L-beam: 50x50x6 (d1000) mm bar material - diameter: 40 (d800) mm square material: 60x60x3 (d4000) mm rectangle: 80x30x3 (d6000) mm tube diameter max.: 70x2 (d1600) mm tool adaptor: 60 mm roll diameter: 177 mm bending speed: 6,4 m/min total power requirement: 4 kW machine weight ab.: 970 kg Overall size: 1400x950x1450 mm Domestic equipments: - hydr. roller drive - Planetary gearbox delivery of the 2 lower rollers - for extra small bending radii - hardened tool holder (42CrMo4) - Standard roller set, hardened - lateral straightening rollers - mobile control panel - 3 driven rollers - Digital display - Machine horizontal u. vertically usable - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW range L-W-H: 900 x 600 x 1000 mm weight: 470 kg connected load: 400/50 V/Hz Equipment / Accessories: - Three driven rollers - Manual delivery of the upper roller - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
shaft diameter: 60 mm Shaft revolutions: 6 U/min roll diameter: 215 mm pressure hydraulic cylinder: 180 kN dimensions: 1125x870x1620 mm weight: 820 kg Accessories / Equipment: - Three driven rollers - Hydraulic delivery of the upper roller - Working position horizontal and vertical - Digital display with memory function - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. It can bend various profiles flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1050 mm plate thickness: 3,3 mm pre-bending: 3,0 mm roll diameter: 90 mm min. dia.: 130 mm total power requirement: 1,1 kw weight of the machine ca.: 570 kg dimensions of the machine ca.: 2100 x 800 x 1130 mm Domestic equipments: - Asymmetrical 3-roll round bending machine with motor drive - Upper roller swung out - Conical bending device - Main engine with brake device Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 50 mm : 8,5 U/min : 100 kN roll diameter: 162 mm Drive: 1,5 kW weight: 495 kg range L-W-H: 1100x850x1100 mm Equipment / Accessories: - Three driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1250 mm plate thickness: 5,5 mm pre-bending: 5,0 mm roll length: 1280 mm min. dia.: 210 mm roll diam. toproll: 140 mm weight: 1365 kg range L-W-H: 2.020 x 900 x 1.200 mm Standard features: - Central rollers via electric motor, planetary reduction gear and Gear drive driven - Swivel top roller - Main engine with brake device - Conical bending device - Mobile controller and foot pedal - CE mark / Declaration of Conformity Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 63x4,2 mm external diameter: min. Ø 5 mm bending radius min.: 10 mm bending radius max.: 270 mm Bending Angle: max. 210 ° bending device: gegen Uhrzeigersinn total power requirement: 0,75 kW weight of the machine ca.: 130 kg dimensions of the machine ca.: 740x470x1030 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll diameter: 215 mm shaft diameter: 60 mm Shaft revolutions: 6 U/min : 100x2 mm : 80x15 mm pressure hydraulic cylinder: 180 kN total power requirement: 2,2 kW weight: 720 kg dimensions: 1200x900x1700 mm Accessories / Equipment: - Three driven rollers - Hydraulic delivery of the upper roller - Working position horizontal and vertical - Digital display with memory function - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. It can bend various profiles flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 60x3 mm : 60x2,5 mm : 35 mm : 64x4 mm : R10-R300 bending speed: 2 U/min total power requirement: 1,5 kW weight of the machine ca.: 130 kg dimensions of the machine ca.: 595x363x900 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 200 kN stroke length max.: 200 mm working feed: 10 mm/sec return speed: 20 mm/sec : 480x1060 mm work height max.: 900 mm toolpiece height max.: 200 mm total power requirement: 2,2 kW : 200x12 mm bending capacity max. - round: 48x4,0 mm weight: 500 kg Overall size: 1010x480x1120 mm Domestic equipments: - with semi-automatic control (99 programs with 16 steps each) - including bending bolt (without punch) - Tool holder for dies - Foot pedal Equipment: - Stamp, small U = 145 mm 85 °, H = 200 mm, R = 5 mm - Quick change monometer 85 °, H = 200 mm, V = 63 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2020 mm plate thickness: 1,5 mm distance between columns: 2050 mm Daylight opening: 100 mm total power requirement: 0,75 kW weight of the machine ca.: 1 t dimensions of the machine ca.: 2,7 x 1 x 1,5 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1000 mm plate thickness: 5,0 mm distance between columns: 1070 mm diameter of upper rolls: 130 mm total power requirement: 4,0 KW weight of the machine ca.: 1,15 t dimensions of the machine ca.: 2,55 x 0,65 x 1,1 mm - Electrically adjustable rear roller - Electrically adjustable lower roll (material clamping) - Digital readout for rear roller movement - Digital readout for lower roll movement (material clamping) - Hardened rolls - Conical rolling - Swiveling top roll - Brake motor - Emergency stop - Documentation - 400V The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 50 (500) mm : 45 (500) mm L-beam: 80 x 80 x 8 (800) mm T - beam - web outwards: 80 x 9 (800) mm Axis diameter: 60 mm work speed: 5,0 m/min Tool diameter: 195 mm total power requirement: 3 kW weight of the machine ca.: 1,0 t dimensions of the machine ca.: 1,2 x 0,9 x 1,2 m Profile bending machine with: - Foot pedal right / left - Recording: wave 50mm - with digital display - hardened special steel shafts - 1 set of standard rollers - Lower rollers are driven - Upper roll up and down hydraulically deliverable - Horizontal and vertical operation - Engine with braking device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1290 mm plate thickness: 5 mm pre-bending: ja roll diameter: 120 mm roll speed: 1 - 6 m/min total power requirement: 1,1 kW weight of the machine ca.: 825 kg Asymmetry roll arrangement, pre-bending ist possible. This new machine is in the following sizes obtainable: working length from 1040 until 2540 mm, max. plate thickness ( 400 N/mm² ) from 1 until 6,5 mm. We are distributor only for Germany. Machine dealer with own stock of 2500 m². The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
chamfer lenght: 480 - 4045 mm 4 pieces of unused upper tools: tool No 5 length: 3050 mm, dimensions see sketch, price = 710,- tool Nr 6 Length: 3073 mm, dimensions see sketch, price = 970,- tool No 9 L = 1925 mm divided, dimensions see sketch, price = 850,- tool Nr.10 length: 1520 mm, dimensions see sketch, price = 850,- Prices excl. VAT Machine dealer with own stock of 2500 m². The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3050 mm plate thickness: 53 mm pre-bending: 45 total power requirement: 60 kW weight of the machine ca.: t dimensions of the machine ca.: m Stocknumber 2210020 Type of machine 4-Roll Plate Bending machine Make DAVI Type MCB 3053 Build in 1998 Type of control Conventional Additional information max. Plate widht 3050 mm Max. plate thickness 53 mm Max. thickness prebending 45 mm Toprol diameter 525 mm under roll diam. 470 mm Site rolls diam. 400 mm Power 78 Hp Hardened rolls Conical bending Dimensions: 6000 x 3100 x 6700 mm in very good condition The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
HEIDELBERG Nela Plate Bending suitable for HD SM 52 / 74 /102 and XL machines different years of construction available
roll diameter: 76-86 mm Shaft diameter: 20 mm Shaft revolutions: 11 U/min Bending capacity round tube: 30 mm : 25x6 mm Angle iron: 20x20x4 mm Drive: 0,18 kW range L-W-H: 530x420x500 mm weight: 80 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Schroeder & Bauer WB 32-1 Universal wire and belt bending machine Wire feed Plain text display Press force monitoring Wire straightener Bosch stripping devices Bracket and brush motor with mounted tool W32/1-32 Soundproof cabin Fäßerb CU wire with stamped parts Switchboard Item condition: very good Description of the manufacturer, deviations possible. You purchase the machine as it can be seen in the pictures. The punch bending machine is located in Hildesheim and can be dismantled and picked up by the customer there. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines
sheet width: 2020 mm plate thickness: 2 mm distance between columns: 2030 mm bending angle max.: 135 ° total power requirement: - kW weight of the machine ca.: 1,22 t dimensions of the machine ca.: 2,5 x 1,0 x 1,4 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
MACRI ITALIA PROVAR 6-45 U-D tube and profile bending machine was built in 2015 in Italy by Macri Italia srl. The machine, designed for precision bending of tubes and profiles with a maximum diameter of 45 mm, is an answer to the daily challenges of modern business. The machining process is performed by means of a moving head with reinforced gears, which allows the bending of standard and variable radiuses in 6 axes (X,Y,Z,B1,B2,A). Each axis, in turn, is driven by brushless servomotors, which ensure the achievement of high dynamics, combined with excellent positioning accuracy. The machine’s extensive range of equipment includes e.g. state-of-the-art MACRI software with many useful functions and the ability to run a anti-collision test with 3D simulation. The PROVAR 6-45 U-D mandrel bending machine weighs 4000 kg. Technical specifications of the MACRI ITALIA PROVAR 6-45 U-D tube be ...
maximum number of results exceeded
please refine your search
