4 roll bending used for sale

pressure: 400 t chamfer lenght: 4100 mm distance between columns: 3550 mm column arm: 510 mm ram stroke speed: 110 mm/sec work speed: 8.4 mm/sec return speed: 130 mm/sec work stroke: 375 mm dayligth: 650 mm table height: 1000 mm table width: 240 mm back stop - adjustable: max. 800 mm oil volume: 400 ltr. voltage: 400 Volt total power requirement: 30.0 kW weight: 26409 kg range L-W-H: 5450 x 2650 x 3470 mm -------------------------------------------------- HIGH-SPEED hydraulic press brake with increased installation height increased cylinder stroke enlarged projection -------------------------------------------------- Furnishing: - DELEM CNC control model DA 66T - swiveling touchscreen control unit - 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning - electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm - on ball screws - controlled electr. Stop fingers Z1 ...

Bending length: 4200 mm pre-bending: 34 mm Bending strength: 38 mm power capacity: kW Number of rollers: 4 Stk Adjustable rollers: Stk diameter of upper rolls: 540 mm diameter of lower rolls: 500 mm side roll diameter: 365 mm work speed: 0 - 8 m/min total power requirement: 55 kW weight of the machine ca.: 35 t Control: Haeusler Bendtronic 2.0 dimensions of the machine ca.: 7.5 x 2.1 x 2.4 m Equipped with: - Haeusler BENDtronic 2.0 control system - Smallest possible bending diameter with upper roller Ø540mm: 595mm (depending on springback) - Roller bearings: Self-adjusting roller bearings - Max. cylinder force against upper roller: 3,245kN - Roller material: 42CrMo4 (1.7225) - Speed compensation between upper and lower roller: automatic when the two-roller drive option is selected - Roller adjustment: hydraulic - Tilting of the lower roller and both side rollers for cone bending: infini ...

Shaft Ø: 40 mm Bending Capacity: Flat bar upright at 500 mm Ø: 60 x 10 mm flat at 400 mm Ø: 100 x 15 mm square at 500 mm Ø: 35 mm L-iron leg outwards at 450 mm Ø: 50 x 50 x 6 mm L-iron leg inwards at 600 mm Ø: 50 x 50 x 6 mm T-iron T outwards/inwards at 600 mm Ø: 60 x 60 x 7/50 x 50 x 6 mm Round bar at 500 mm Ø: 35 mm Shaft speed: 7.5 rpm electr. Connection: 380 V, approx. 1.7 kW Space requirement: 910 x 640 x 1400 mm Weight: approx. 400 kg

sheet width: 4200 mm plate thickness: 14 mm pre-bending: 10 mm roll diam. toproll: 340 mm roll diam. bottom roll: 310 mm speed: - m/min Control: Davi CNC total power requirement: - kW weight of the machine ca.: 11 t dimensions of the machine ca.: 6,5 x 1,75 x 1,65 m - DAVI CNC control - pre-Bending - Hydraulic 4-roller drive - Side roll diameter: 230 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 4000 mm plate thickness: 30 / 35 mm pre-bending: 30 mm diameter of upper rolls: 570 mm side roll diameter: 450 mm diameter of lower rolls: 540 mm bending speed: 4 m/min min. bending diameter: 650 mm total power requirement: 60 kW weight of the machine ca.: 52 to dimensions of the machine ca.: - m The machine was overhauled in 2022 Equipment: - Hydraulic 4-roller round bending machine - Roll material: 61 MnCrMo 43 - Driven rolls: 2 Top-and bottom roll -- Drive: over 2 hydro motors direct flanged -- Adjustment speed bottom roll: 0-200 mm/min -- Adjustment speed side rolls: 0-700 mm/min - Speed compensation between top-and bottom roll: automatic - Operation of the tilting bearing: hydraulic - Tilting of the top roll: hydraulic - Bearing block: hydraulic - Indicator device of roll position: digital The data for this ad was created with ModulMWS - the software solution of Logo ...

4 ROLL HYDRAULIC DUAL PRE-PINCH 3000x15 MM PLATE BENDING MACHINE NEW Brand MG model M3015 -Width of plate 3000 mm -Thickness of plate rolling 15 mm -Thickness of plate pre-bend 12 mm minimum bending diameter ID 350 mm Rolls dimensions: -Surface length mm. 3100 -Top roll mm. 290 -pinch roll mm. 270 -Power electric 10 Hp Technical data: -rolls hardened surface high resistance -variable rolling speed -Powered driven hydraulic rolls rotation -conical bending attachment roller type -calibration system re-rolling welded shells -deflection pinch pressure adjustable upon the thickness -overload protect complete safe operation of the machine. -control console on wheels with electric joysticks commands -position readout digital display for rolling memorize and repeat -safety and emergency systems installed -manuals and schematics along with the machine

Offer 26148 Technical data: - Pressure capacity 420 KN / 42 t - Stroke length 0 - 300 mm - Lifting speed 0 - 0.6 m/min - Tool height 200 mm - Bending performance - with prism MW 125 flat approx. 200 x 16 mm - with prism MW 240 flat approx. 200 x 24 mm - Tube bending up to 2 inches - CNC control SIEMENS SIMATIC HMI TOUCH - For angle programming + length programming - Controlled length stop 3000 mm - Various bending tools - Operating hours (read) 1404 h - Drive 400 V / 4.0 kW - Space requirement approx. W 850 x H 1250 x D 1250 mm - Weight approx. 1200 kg

A BPR ring bending machine is available. Shaft diameter: 40mm, max. roller diameter: 162mm, center distance: 300mm, shaft speed: 7.5rpm, max. flat steel bending capacity: 100mm/15mm, max. edgewise steel bending capacity: 60mm/10mm, max. bending diameter: 35mm, machine dimensions X/Y/Z: approx. 950mm/650mm/1400mm, weight: approx. 500kg. An on-site inspection is possible.

pressure: 150 t chamfer lenght: 4300 mm distance between columns: 3700 mm ram stroke speed: 100 mm/sec working feed: 8 mm/sec return speed: 80 mm/sec stroke: 175 mm table height: 920 mm Control: DELEM DA 52 total power requirement: 11 kW weight of the machine ca.: 15000 kg dimensions of the machine ca.: 4800 x 1700 x 2850 mm Equipment: - Controlled axes Y1 - Y2 - X, as well as CNC crowning - DELEM DA52 CNC control - Electric backgauge (X-axis) - 4x manually adjustable stop fingers - 2x front support arms - AMADA UKB system upper tool holder - Side guard - Foot switch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

tube diameter: 40-168 x10,0 mm wall strength: . mm bending radius min.: ohne Rohr 190 mm voltage: 380 V operating pressure: 200 bar total power requirement: . kW weight of the machine ca.: 22 t dimensions of the machine ca.: 7,50x2,8x1,6 ( 30 m²) m The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoT ...

pressure: 400 t throat: 1140 mm stroke: 600 mm table surface area: 2000x1000 mm Plate: 4000x1000x300 mm ram head dimension: 2000x1040 mm Cylinder: 300 mm Daylight: 650 total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: 3,9x4x4,2 m Machine has been overhauled. Maximum distance from ram to clamping plate: 1250 mm The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your  ...

pressure: 400 t chamfer lenght: 4000 mm distance between columns: 3500 mm Control: CNC type: BC 25 Graphic throat: 400 mm total power requirement: 37,5 kW weight of the machine ca.: 25 t dimensions of the machine ca.: m The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 Wochen ab Auftrags : Italien : 3050 mm : 16 mm : 16 mm : 10 mm : 13 mm : 11 mm Hardened and polished rollers Numerical control Siemens PGS-Classic with touchscreen Cone bending with electronic control and inclination of the bottom roller oil cooler Simultaneous rotation and roller movement Simultaneous roller and support movement Possibility to bend variable radii (ovals, ellipses, etc.) Hydraulic micro-positioning by the PLC for higher accuracy Infinitely variable speed for roller movement Infinitely variable speed for rotation Prepared for retrofitting supports (up to 5 axes) Prepared for retrofitting loading/unloading stations Prepared for retrofitting CNC controls Extra large, double hinged drop end Electronic parallelism system for the synchronization of the rollers Hydraulic lifting of the top roll (for models with a top roll diameter of 205 mm or more) Double linear ...

: neu : ca. 12 Wochen ab Auftrags : Italien : 3050 mm : 7 mm : 7 mm : 4 mm : 5 mm : 5 mm Hardened and polished rollers Numerical control Siemens PGS-Classic with touchscreen Cone bending with electronic control and inclination of the bottom roller oil cooler Simultaneous rotation and roller movement Simultaneous roller and support movement Possibility to bend variable radii (ovals, ellipses, etc.) Hydraulic micro-positioning by the PLC for higher accuracy Infinitely variable speed for roller movement Infinitely variable speed for rotation Prepared for retrofitting supports (up to 5 axes) Prepared for retrofitting loading/unloading stations Prepared for retrofitting CNC controls Extra large, double hinged drop end Electronic parallelism system for the synchronization of the rollers Hydraulic lifting of the top roll (for models with a top roll diameter of 205 mm or more) Double linear guid ...

: neu : ca. 14 - 16 Wochen ab Auf : Türkei : 252800 € : 600 to : 4050 mm : Y1 / Y2 / X und R Achse : 365 mm : 3100 mm : 410 mm : 700 mm : hydraulisch : 160 mm/s : 10 mm/s : 160 mm/s : 650 mm : 500 mm/s : 250 mm : 900 mm : 154 mm : 280 l : 5750 mm : 2500 mm : 4000 mm : 40500 kg 1 SERVO MOTOR AND PUMP PER CYLINDER 4 axes (Y1, Y2,X andR) CNC control SKY 22 - intuitive touch-screen control (simple drawing of the bending outline with your finger) 21,5 in full HD - with 2D and 3D working screen - direct programming of the bending angle - user friendly programming in dialogue form optionally in 2D or 3D mode - 2D and 3D simulation of the bending sequence - automatic tool selection in 3D mode - automatic calculation of the blank sheet size - bending order calculation - graphic product and tool memory - correction possibility - USB and Ethernet interfaces for import, backup and programm transp ...

: neu : ca. 12 - 14 Wochen ab Auf : Slowakei : 23700 € : 455.04 € : 40 to : 800 mm : X und Y Achse : 100 mm : 310 mm : hydraulisch : 38 l : 6 kW : 1750 mm : 950 mm : 1900 mm : 1640 kg : 420 mm : 1 : 10 mm/s : 12 mm/s : 40 mm/s : 0.02 +/- mm : 0.05 +/- mm 2 axes(Y andX) motorized backgauge with push button and manual fine adjustment with counter preselection of press depth Y and upper dead point intermediate piece with quick-release lever for upper tool clamping upper tool 1010/75/R0,8/105 1x835 mm + 1x835 mm divided die type2009/85° (V16/22/35/50 mm)1x835 mm + 1x835 mm divided 2 support arms according to CE rules oilfilling user manual in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : 2026 : 080147 : prompt, Zwischenverkauf v : Slowakei : 26400 € : 504.24 € : 1 : 40 to : 1500 mm : X und Y Achse : 100 mm : 310 mm : hydraulisch : 38 l : 6 kW : 2000 mm : 950 mm : 1900 mm : 1800 kg : 420 mm : 1 : 10 mm/s : 12 mm/s : 40 mm/s : 0.02 +/- mm : 0.05 +/- mm 2 axes(Y andX) motorized backgauge with push button and manual fine adjustment with counter preselection of press depth Y and upper dead point intermediate piece with quick-release lever for upper tool clamping upper tool 1010/75/R0,8/105 1x835 mm + 1x835 mm divided die type2009/85° (V16/22/35/50 mm)1x835 mm + 1x835 mm divided 2 support arms according to CE rules oilfilling user manual in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 - 14 Wochen ab Auf : Slowakei : 28300 € : 540.53 € : 40 to : 2000 mm : X und Y Achse : 100 mm : 310 mm : hydraulisch : 38 l : 6 kW : 2500 mm : 1200 mm : 1900 mm : 2100 kg : 420 mm : 1 : 10 mm/s : 12 mm/s : 40 mm/s : 0.02 +/- mm : 0.05 +/- mm 2 axes(Y andX) motorized backgauge with push button and manual fine adjustment with counter preselection of press depth Y and upper dead point intermediate piece with quick-release lever for upper tool clamping upper tool 1010/75/R0,8/105 1x835 mm + 1x835 mm divided die type2009/85° (V16/22/35/50 mm)1x835 mm + 1x835 mm divided 2 support arms according to CE rules oilfilling user manual in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 - 14 Wochen ab Auf : Slowakei : 25400 € : 485.14 € : 40 to : 1250 mm : X und Y Achse : 100 mm : 310 mm : hydraulisch : 38 l : 6 kW : 1750 mm : 950 mm : 1900 mm : 1640 kg : 420 mm : 1 : 10 mm/s : 12 mm/s : 40 mm/s : 0.02 +/- mm : 0.05 +/- mm 2 axes(Y andX) motorized backgauge with push button and manual fine adjustment with counter preselection of press depth Y and upper dead point intermediate piece with quick-release lever for upper tool clamping upper tool 1010/75/R0,8/105 1x835 mm + 1x835 mm divided die type2009/85° (V16/22/35/50 mm)1x835 mm + 1x835 mm divided 2 support arms according to CE rules oilfilling user manual in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : 2026 : 090209 : prompt, Zwischenverkauf v : Italien : 7780 € : 150.15 € : 1 : 1 : 42 mm : 400 mm : 570 mm : 1000 mm : 80 kg : 4 cm³ : 42 x 3 mm : 48 x 1,5 mm : 42 x 4 mm : 42 x 2 mm : 42 x 2 mm : 50 x 3 mm : 54 x 2 mm : 54 x 2 mm : 60 x 2 mm : 50 x 4 mm : 30 mm : 40x20 (liegend), 40x12 (s mm : 260 mm : 10 mm : 3,3 U/min : 1.1 kW manual clamping electronic preselection of bending angle digital read our for Clamping position 30 programms with each 9 bends material spring back compensation overload protection mobile by rolls and handle foot pedal tools not included Alternatively also available as following models (prices on request): MB 42M (single phase, 2 U/min) MB 42PM (portable, single phase, 2 U/min) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 10 Wochen ab Auftrags : Türkei : 159300 € : 3010.77 € : 320 to : 4050 mm : Y1 / Y2 / X und R Achse : 365 mm : 3600 mm : 410 mm : 630 mm : hydraulisch : 160 mm/s : 10 mm/s : 160 mm/s : 650 mm : 500 mm/s : 250 mm : 900 mm : 154 mm : 5300 mm : 1910 mm : 3230 mm : 20100 kg 1 SERVO MOTOR AND PUMP PER CYLINDER 4 axes (Y1, Y2,X andR) CNC control SKY 22 - intuitive touch-screen control (simple drawing of the bending outline with your finger) 21,5 in full HD - with 2D and 3D working screen - direct programming of the bending angle - user friendly programming in dialogue form optionally in 2D or 3D mode - 2D and 3D simulation of the bending sequence - automatic tool selection in 3D mode - automatic calculation of the blank sheet size - bending order calculation - graphic product and tool memory - correction possibility - USB and Ethernet interfaces for import, backup and programm  ...

: neu : ca. 10 Wochen ab Auftrags : Türkei : 100920 € : 1907.39 € : 220 to : 4050 mm : Y1 / Y2 / X Achse : 265 mm : 3600 mm : 450 mm : 530 mm : hydraulisch : 160 mm/s : 10 mm/s : 140 mm/s : 500 mm/s : 350 mm/s : 250 mm : 900 mm : 104 mm : 250 l : 22 kW : 5250 mm : 1770 mm : 3000 mm : 14750 kg Standard accessories: 3 axes (Y1, Y2,X) CNC control DT-15 - 2D grafic display 15", - intuitive touch-screen control (simple drawing of the bending outline with your finger) - user friendly programming in dialogue form - automatic calculation of the bending sequence - automatic calculation of the blank sheet size - graphic product and tool memory - correction possibility - USB interfaces for backup and programm transportation - PC software, generating programms on the PC and transfer to the machine by USB servo motorized back gauge on linear guides and ball screws back gauge finger blocks on ...

pressure: 160 t chamfer lenght: 4100 mm distance between columns: 3600 mm column arm: 400 mm ram stroke speed: 200 mm/sec work speed: 10.0 mm/min return speed: 165 mm/sec work stroke: ca. 350 mm dayligth: ca. 660 mm oil volume: 450 ltr. table height: 830 / 950 mm table width: 75.0 / 60.0 mm voltage: 400 Volt total power requirement: 18.5 kW weight: 13440 kg range L-W-H: 5150 x 2050 x 3150 mm current new price approx. 90.000 euros special price on request ------------------------------------------------------ ULTIMA PLUS electro-hydraulic press brake with: increased installation height .. approx. 660 mm increased cylinder stroke .. approx. 350 mm ----------------------------------------------------- - in checked condition - machine video - https://www.youtube.com/watch?v=chgCaXLnpa8 Equipment: - CNC electro-hydraulic die/press brake - CYBELEC CNC control DNC 880 S swiveling control p ...

: neu : ca. 4 Wochen ab Auftragse : Italien : 9340 € : 180.26 € : 48 mm : 570 mm : 410 mm : 1000 mm : 110 kg : 6 cm³ : 48 x 3,5 mm : 11/2 x 3.68 mm : 54 x 1,5 mm : 50 x 4 mm : 48 x 2 mm : 48 x 2 mm : 60 x 3 mm : 64 x 2 mm : 64 x 2 mm : 60 x 2 mm : 50 x 4 mm : 32 mm : 45 x 16 stehend, 45 x 25 mm : 300 mm : 10 mm : 10 mm : 2/3 U/min : 1.5 kW 3 phase digital display of bend material spring back compensation quick-change tooling system 2 hexagonal tool holders accurate counterbending die positioning portable with base wheels footswitch users manual ALTERNATIVELY ALSO AVAILABLE AS FOLOWING MODEL (PRICE ON REQUEST): SB 48M (single phase, 2 r/min) Model with TCPlus control on request MACHINE-KIT WITH TOOLS (PRICES ON REQUEST): Art.Nr. maschine tube radius SB 48M K2D SB 48M Gas inch 2 x Ø SB 48T K2D SB 48T Gas inch 2 x Ø tools: Ø 1/2", (21,3 mm), R46 Ø 3/4", (26,9 mm), R56 Ø  ...

: neu : ca. 12 Wochen ab Auftrags : Italien : 2500 mm : 8 mm : 8 mm : 4.9 mm : 6 mm : 6 mm Hardened and polished rollers Numerical control Siemens PGS-Classic with touchscreen Cone bending with electronic control and inclination of the bottom roller oil cooler Simultaneous rotation and roller movement Simultaneous roller and support movement Possibility to bend variable radii (ovals, ellipses, etc.) Hydraulic micro-positioning by the PLC for higher accuracy Infinitely variable speed for roller movement Infinitely variable speed for rotation Prepared for retrofitting supports (up to 5 axes) Prepared for retrofitting loading/unloading stations Prepared for retrofitting CNC controls Extra large, double hinged drop end Electronic parallelism system for the synchronization of the rollers Hydraulic lifting of the top roll (for models with a top roll diameter of 205 mm or more) Double linear gu ...

pressure: 220 t chamfer lenght: 4100 mm distance between columns: 3600 mm Control: Cybelec CybTouch 12 throat: 400 mm stroke: 220 mm dayligth: 480 mm : 140 mm/s bending speed: 0-10 mm/s : 110 mm/s total power requirement: 18,5 kW dimensions: 4500x2000x2900 mm weight: 13.000 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 200 t chamfer lenght: 4100 mm Control: CYBELEC DNC 900 stroke: 260 mm weight of the machine ca.: 16.000 kg dimensions of the machine ca.: 4500x2400x3000 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 400 kN stroke length max.: 285 mm working feed: 9 mm/sec return speed: 20 mm/sec : 660x1250 mm work height max.: 930 mm toolpiece height max.: 250 mm total power requirement: 4 kW : 200x26 mm bending capacity max. - round: 60x5,0 mm Domestic equipments: - semi-automatic NC control (99 programs with 16 steps each) - incl. bending bolt (without punch) - Incl. tool holder for dies - incl. foot pedal The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 125 t chamfer lenght: 4000 mm distance between columns: 4100 mm Control: Cybelec VisiTouch 24MX stroke: 300 mm dayligth: 500 mm : 200 mm/s bending speed: 0-12 mm/s total power requirement: 18 kW weight of the machine ca.: 13.000 kg dimensions: 5080 x 3110 x 1800 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 330 t chamfer lenght: 4100 mm distance between columns: 3600 mm Control: Cybelec VisiTouch 24 Arm length: 500 mm stroke: 300 mm dayligth: 500 mm : 165 mm/s bending speed: 0 - 10 mm/s total power requirement: 32 kW weight of the machine ca.: 21.000 kg dimensions: 4850 x 2300 x 3520 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 185 t chamfer lenght: 4000 mm distance between columns: 4100 mm Control: Cybelec VisiTouch 24MX stroke: 300 mm dayligth: 500 mm : 175 mm/s bending speed: 0-12 mm/s total power requirement: 22 kW weight of the machine ca.: 15.500 kg dimensions: 4970 x 3260 x 2090 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 225 t chamfer lenght: 4050 mm distance between columns: 3550 mm control: CYBELEC DNC 86 PS total power requirement: 18,5 kW weight of the machine ca.: 18.000 kg dimensions of the machine ca.: 5180x2400x3200 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 200 t chamfer lenght: 4100 mm distance between columns: 3150 mm stroke of upper beam: 200 mm dayligth: 425 mm throat: 300 mm working feed: 9.0 mm/sec return speed: 90.0 mm/sec work height max.: 980 mm back stop - adjustable: ca. 700 mm Control: PPS-TS Touch oil volume: 350 l total power requirement: 18.0 kW weight: 12.000 kg range L-W-H: 5100 x 1950 x 2850 mm Well-maintained condition () Current new price approx. € 110.000 Special price on request - in checked conditions - machinevideo - https://www.youtube.com/watch?v=ZX9Ap23e__s Equipment: - CNC electro-hydraulic press brakes - with LVD CNC PPS-TS TOUCH control unit intuitive, touchscreen-based user interface simple navigation tool and program library X-axis control and position display Y-axis control and position display swivel-mounted control panel (front left) - CNC-controlled axes: Y1/Y2 + X - CNC motorized bac ...

: neu : ca. 4 Monate ab Auftragse : Italien : 258000 € : 400 to : 500 mm : 5.000 x 3.050 mm : 700 mm : 20 mm/s : 2 mm/s : 4500 mm : 5000 mm : 2600 mm : 24000 kg : horizontal verschiebbar : 3050 mm : 2.200 mm : 3.600 mm Horizontal verschiebbarer Zylinder2.200 mm Hydraulisch beweglicher Ständer: 3.600 mm Bedienung über Handhebel sowie Bedienpanel Tisch mit integriertem Zylinder zum anheben des Werkstücks Ausrüstung gemäß CE Vorschriften Betriebsanleitung in DEUTSCH und ENGLISCH (Symbolfoto) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 - 14 Wochen ab Auf : Türkei : 76820 € : 1451.9 € : 160 to : 4050 mm : Y1 / Y2 und X Achse : 200 mm : 3600 mm : 300 mm : 430 mm : hydraulisch : 160 mm/s : 10 mm/s : 140 mm/s : 620 mm : 250 mm/s : 858 mm : 104 mm : 15 kW : 4850 mm : 1900 mm : 2610 mm : 10500 kg 3 axes (Y1, Y2, and X axis) CNC control DT-10 - intuitive touch-screen control (simple drawing of the bending outline with your finger) - user friendly programming in dialogue form - automatic calculation of bending sequence - automatic calculation of the blank sheet size - graphic product and tool memory - correction possibility - USB interfaces for backup and programm transportation - PC software, generating programms on the PC and transfer to the machine by USB CNC controlled back gauge with linear guide and ball screw spindles CNC crowning table intermediate clamps for upper tool upper tool1010/A/75°/0,8, se ...

: neu : ca. 14 - 16 Wochen ab Auf : Türkei : 171300 € : 3237.57 € : 400 to : 4050 mm : Y1 / Y2 / X Achse : 365 mm : 3400 mm : 510 mm : 630 mm : hydraulisch : 160 mm/s : 10 mm/s : 140 mm/s : 500 mm/s : 350 mm/s : 250 mm : 1050 mm : 154 mm : 250 l : 37 kW : 5750 mm : 2110 mm : 3640 mm : 27760 kg 3 axes (Y1, Y2,X) CNC control DT-15 - 2D grafic display 15", - intuitive touch-screen control (simple drawing of the bending outline with your finger) - user friendly programming in dialogue form - automatic calculation of the bending sequence - automatic calculation of the blank sheet size - graphic product and tool memory - correction possibility - USB interfaces for backup and programm transportation - PC software, generating programms on the PC and transfer to the machine by USB servo motorized back gauge on linear guides and ball screws back gauge finger blocks on double linear guides ...

: neu : ca. 12 Wochen ab Auftrags : Italien : 3050 mm : 25 mm : 25 mm : 16 mm : 20 mm : 18 mm Hardened and polished rollers Numerical control Siemens PGS-Classic with touchscreen Cone bending with electronic control and inclination of the bottom roller oil cooler Simultaneous rotation and roller movement Simultaneous roller and support movement Possibility to bend variable radii (ovals, ellipses, etc.) Hydraulic micro-positioning by the PLC for higher accuracy Infinitely variable speed for roller movement Infinitely variable speed for rotation Prepared for retrofitting supports (up to 5 axes) Prepared for retrofitting loading/unloading stations Prepared for retrofitting CNC controls Extra large, double hinged drop end Electronic parallelism system for the synchronization of the rollers Hydraulic lifting of the top roll (for models with a top roll diameter of 205 mm or more) Double linear ...

: neu : ca. 2 Wochen ab Auftragse : Italien : 2000 mm : 11 mm : 11 mm : 7 mm : 8 mm : 6.4 mm : 225 mm : 215 mm : 165 mm : 8 m/min : 3950 mm : 1200 mm : 1200 mm : 4450 kg Hardened and polished rollers Numerical control Siemens PGS-Classic with touchscreen Cone bending with electronic control and inclination of the bottom roller oil cooler Simultaneous rotation and roller movement Simultaneous roller and support movement Possibility to bend variable radii (ovals, ellipses, etc.) Hydraulic micro-positioning by the PLC for higher accuracy Infinitely variable speed for roller movement Infinitely variable speed for rotation Prepared for retrofitting supports (up to 5 axes) Prepared for retrofitting loading/unloading stations Prepared for retrofitting CNC controls Extra large, double hinged drop end Electronic parallelism system for the synchronization of the rollers Hydraulic lifting of the to ...

: neu : ca. 12 Wochen ab Auftrags : Italien : 2000 mm : 28 mm : 28 mm : 22 mm : 26 mm : 23 mm Hardened and polished rollers Numerical control Siemens PGS-Classic with touchscreen Cone bending with electronic control and inclination of the bottom roller oil cooler Simultaneous rotation and roller movement Simultaneous roller and support movement Possibility to bend variable radii (ovals, ellipses, etc.) Hydraulic micro-positioning by the PLC for higher accuracy Infinitely variable speed for roller movement Infinitely variable speed for rotation Prepared for retrofitting supports (up to 5 axes) Prepared for retrofitting loading/unloading stations Prepared for retrofitting CNC controls Extra large, double hinged drop end Electronic parallelism system for the synchronization of the rollers Hydraulic lifting of the top roll (for models with a top roll diameter of 205 mm or more) Double linear ...

: neu : ca. 12 - 14 Wochen ab Auf : Türkei : 94120 € : 1778.87 € : 175 to : 4050 mm : Y1 / Y2 / X Achse : 265 mm : 3600 mm : 450 mm : 530 mm : hydraulisch : 160 mm/s : 10 mm/s : 140 mm/s : 500 mm/s : 350 mm/s : 250 mm : 900 mm : 104 mm : 250 l : 18.5 kW : 5250 mm : 1700 mm : 2850 mm : 12780 kg 3 axes (Y1, Y2,X) CNC control DT-15 - 2D grafic display 15", - intuitive touch-screen control (simple drawing of the bending outline with your finger) - user friendly programming in dialogue form - automatic calculation of the bending sequence - automatic calculation of the blank sheet size - graphic product and tool memory - correction possibility - USB interfaces for backup and programm transportation - PC software, generating programms on the PC and transfer to the machine by USB servo motorized back gauge on linear guides and ball screws back gauge finger blocks on double linear guides ...

: neu : ca. 12 Wochen ab Auftrags : Italien : 2000 mm : 18 mm : 18 mm : 12.1 mm : 15 mm : 13 mm Hardened and polished rollers Numerical control Siemens PGS-Classic with touchscreen Cone bending with electronic control and inclination of the bottom roller oil cooler Simultaneous rotation and roller movement Simultaneous roller and support movement Possibility to bend variable radii (ovals, ellipses, etc.) Hydraulic micro-positioning by the PLC for higher accuracy Infinitely variable speed for roller movement Infinitely variable speed for rotation Prepared for retrofitting supports (up to 5 axes) Prepared for retrofitting loading/unloading stations Prepared for retrofitting CNC controls Extra large, double hinged drop end Electronic parallelism system for the synchronization of the rollers Hydraulic lifting of the top roll (for models with a top roll diameter of 205 mm or more) Double line ...

: neu : ca. 12 Wochen ab Auftrags : Italien : 1500 mm : 6 mm : 6 mm : 4 mm : 5 mm : 4 mm Hardened and polished rollers Numerical control Siemens PGS-Classic with touchscreen Cone bending with electronic control and inclination of the bottom roller oil cooler Simultaneous rotation and roller movement Simultaneous roller and support movement Possibility to bend variable radii (ovals, ellipses, etc.) Hydraulic micro-positioning by the PLC for higher accuracy Infinitely variable speed for roller movement Infinitely variable speed for rotation Prepared for retrofitting supports (up to 5 axes) Prepared for retrofitting loading/unloading stations Prepared for retrofitting CNC controls Extra large, double hinged drop end Electronic parallelism system for the synchronization of the rollers Hydraulic lifting of the top roll (for models with a top roll diameter of 205 mm or more) Double linear guid ...

: neu : ca. 12 Wochen ab Auftrags : Italien : 2500 mm : 27 mm : 27 mm : 18 mm : 23 mm : 20 mm Hardened and polished rollers Numerical control Siemens PGS-Classic with touchscreen Cone bending with electronic control and inclination of the bottom roller oil cooler Simultaneous rotation and roller movement Simultaneous roller and support movement Possibility to bend variable radii (ovals, ellipses, etc.) Hydraulic micro-positioning by the PLC for higher accuracy Infinitely variable speed for roller movement Infinitely variable speed for rotation Prepared for retrofitting supports (up to 5 axes) Prepared for retrofitting loading/unloading stations Prepared for retrofitting CNC controls Extra large, double hinged drop end Electronic parallelism system for the synchronization of the rollers Hydraulic lifting of the top roll (for models with a top roll diameter of 205 mm or more) Double linear ...

: neu : ca. 12 - 14 Wochen ab Auf : Türkei : 187100 € : 3536.19 € : 400 to : 4050 mm : Y1 / Y2 / X und R Achse : 365 mm : 3400 mm : 410 mm : 630 mm : hydraulisch : 160 mm/s : 10 mm/s : 160 mm/s : 650 mm : 500 mm/s : 250 mm : 900 mm : 154 mm : 2 x 11 kW : 5750 mm : 2110 mm : 3450 mm : 27780 kg 1 SERVO MOTOR AND PUMP PER CYLINDER 4 axes (Y1, Y2,X andR) CNC control SKY 22 - intuitive touch-screen control (simple drawing of the bending outline with your finger) 21,5 in full HD - with 2D and 3D working screen - direct programming of the bending angle - user friendly programming in dialogue form optionally in 2D or 3D mode - 2D and 3D simulation of the bending sequence - automatic tool selection in 3D mode - automatic calculation of the blank sheet size - bending order calculation - graphic product and tool memory - correction possibility - USB and Ethernet interfaces for import, backup a ...

: neu : ca. 4 Monate ab Auftragse : Italien : 218000 € : 400 to : 500 mm : 4.000 x 2.550 mm : 700 mm : 20 mm/s : 2 mm/s : 4000 mm : 4000 mm : 2600 mm : 20500 kg : horizontal verschiebbar : 2550 mm : 1.800 mm : 2.900 mm horizontal movable cylinder hydraulicaly movable stand control by levers as well as control panel according to CE regulations user manual in GERMAN and ENGLISH OPTIONS: Work table, welded to the base frame, with holes on the surface Control panel on the swivel arm (push buttons for press movement, solenoid valves, Siemens CPU) Radio control panel (push buttons for press movement, solenoid valves, Siemens CPU) Siemens control with touchscreen Lifting cylinders in the table (6, 8 or 10 pcs.) No-rotation shaft for the piston 2 speeds for stand movement and cylinder Oil cooler and decompression valve The data for this ad was created with ModulMWS - the software solution of  ...

: neu : ca. 10 Wochen ab Auftrags : Türkei : 127400 € : 2407.86 € : 220 to : 4050 mm : Y1 / Y2 / X und R Achse : 265 mm : 3600 mm : 410 mm : 530 mm : hydraulisch : 200 mm/s : 12 mm/s : 180 mm/s : 650 mm : 500 mm/s : 250 mm : 900 mm : 104 mm : 5250 mm : 1770 mm : 2900 mm : 15000 kg 1 SERVO MOTOR AND PUMP PER CYLINDER Standard accessories: 4 axes (Y1, Y2,X andR) CNC control SKY 22 - intuitive touch-screen control (simple drawing of the bending outline with your finger) 21,5 in full HD - with 2D and 3D working screen - direct programming of the bending angle - user friendly programming in dialogue form optionally in 2D or 3D mode - 2D and 3D simulation of the bending sequence - automatic tool selection in 3D mode - automatic calculation of the blank sheet size - bending order calculation - graphic product and tool memory - correction possibility - USB and Ethernet interfaces for import ...

: neu : ca. 10 Wochen ab Auftrags : Türkei : 123713 € : 2338.18 € : 320 to : 4050 mm : Y1 / Y2 / X Achse : 365 mm : 3600 mm : 450 mm : 630 mm : hydraulisch : 160 mm/s : 10 mm/s : 140 mm/s : 500 mm/s : 350 mm/s : 250 mm : 900 mm : 154 mm : 250 l : 18.5 kW : 5250 mm : 1770 mm : 2850 mm : 20000 kg Standard accessories: 3 axes (Y1, Y2,X) CNC control DT-15 - 2D grafic display 15", - intuitive touch-screen control (simple drawing of the bending outline with your finger) - user friendly programming in dialogue form - automatic calculation of the bending sequence - automatic calculation of the blank sheet size - graphic product and tool memory - correction possibility - USB interfaces for backup and programm transportation - PC software, generating programms on the PC and transfer to the machine by USB servo motorized back gauge on linear guides and ball screws back gauge finger blocks  ...

: neu : ca. 12 Wochen ab Auftrags : Türkei : 25200 € : 481.32 € : 1050 mm : 2.5 mm : 2.5 mm : 2 mm : 90 mm : 4,5 m/min : 2.2 kW : 2250 mm : 1000 mm : 1500 mm : 900 kg FOR ROUND AND ELEPTIC SHAPES FOR MASS PRODUCTION (CYCLE UP TO ONLY 20 SEC POSSIBLE) 4 rolls NC control with touchscreen Top roll driven by hydromotor and plantary gearbox Hydraulic drop end Mobile control panel Hardened rolls Operating manual in English or German OPTION: Feeding table price on request The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 Wochen ab Auftrags : Italien : 2000 mm : 6 mm : 6 mm : 4 mm : 5 mm : 4.5 mm Hardened and polished rollers Numerical control Siemens PGS-Classic with touchscreen Cone bending with electronic control and inclination of the bottom roller oil cooler Simultaneous rotation and roller movement Simultaneous roller and support movement Possibility to bend variable radii (ovals, ellipses, etc.) Hydraulic micro-positioning by the PLC for higher accuracy Infinitely variable speed for roller movement Infinitely variable speed for rotation Prepared for retrofitting supports (up to 5 axes) Prepared for retrofitting loading/unloading stations Prepared for retrofitting CNC controls Extra large, double hinged drop end Electronic parallelism system for the synchronization of the rollers Hydraulic lifting of the top roll (for models with a top roll diameter of 205 mm or more) Double linear gu ...

: neu : ca. 12 Wochen ab Auftrags : Italien : 2000 mm : 22 mm : 22 mm : 16 mm : 19 mm : 17 mm Hardened and polished rollers Numerical control Siemens PGS-Classic with touchscreen Cone bending with electronic control and inclination of the bottom roller oil cooler Simultaneous rotation and roller movement Simultaneous roller and support movement Possibility to bend variable radii (ovals, ellipses, etc.) Hydraulic micro-positioning by the PLC for higher accuracy Infinitely variable speed for roller movement Infinitely variable speed for rotation Prepared for retrofitting supports (up to 5 axes) Prepared for retrofitting loading/unloading stations Prepared for retrofitting CNC controls Extra large, double hinged drop end Electronic parallelism system for the synchronization of the rollers Hydraulic lifting of the top roll (for models with a top roll diameter of 205 mm or more) Double linear ...