127,909 used machines on RESALE, but how to find them? Machine Search
Three welding machines are available. (1) Castolin+Eutectic CASTOWIG 150 G, power supply: 5A/10V to 150A/16V, max. short-circuit current: 0.15kA, weight: 50kg. (2) MIG O MAT WIGSTAR 250i, welding current: 10-250A, duty cycle: 100% at 160A, 60% at 200A. (3) Lorch SEW 200N, voltage: 400V, welding current: 230A, cooling: gas-cooled. (4) Heberle stud welding systems cd System 2010, connected load: 0.6kVA. On-site inspection is possible.
Clamping force: 2500kN, clear tie bar distance: 630mm/630mm, opening stroke: 1150mm, min. mold installation height: 330mm, screw diameter: 60mm, specific injection pressure: 2000bar, max. stroke volume: 670cm³, connected load: 74kW, control: MC4. Machine dimensions: 5700mm/2200mm/2300mm, machine weight: 12.5t, operating hours: 47,572h. Available from February 2025, including special accessories, Krauss Maffei LRX-S 100, 8x hot runner control points, 4x core pull, blow-out unit, pressure accumulator, hydraulic tie-bar pulling device, energy-saving circuit, ALS interface, 20mA interface and color dosing device interface. On-site inspection is possible, documentation available.
Clamping force: 25kN, injection force: 5.7kN, screw motor: 12Nm, heating: 3.4kW.
There are five injection moulding machines Arburg available. 1) Arburg 320C 600-250, year of construction: 2001, operating hours: 83,365h. 2) Arburg 420C 1000-250, year of manufacture: 2001, operating hours: 90,769h. 3) Arburg 270C 300-100, year of construction: 1999, operating hours: 78,784h. 4) Arburg 320C 300-100, year of construction: 2000, operating hours: 78,784h. 5) Arburg 270C 300-100, year of construction: 2007, operating hours: 59,885h.
Injection pressure: 2100bar, injection volume: 595cm³, injection weight: 565g, injection speed: 299cm³/s. Clamping force: 250t, clamping force: 275t, platen dimensions X/Y: 920mm/920mm, opening stroke: 575mm, mold height min./max.: 200mm/685mm, tie bar distance: 585mm, ejector stroke: 175mm, ejector stroke: 180mm, centering: 160mm, operating hours: 62149h. Documentation available. On-site inspection is possible.
Decoiler Coil weight: 2,5 ton Material width: 50 - 500 mm Coil exterior diameter: 1400 mm Expansion range: 420 - 520 mm Leveller / Straightener Material width : 500 mm Number of levelling rolls: 9 pcs. Diameter of the levelling rolls: 50 mm Number of pinch rolls: 2 pcs. Material thickness: 6 mm Cross section: 3000 sq mm Feeding speed: 6 - 24 m / min
cutting width: 150 mm machine weight ab.: 300 kg : 27468 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
turning diameter: 250 mm turning length: 100 mm control: SIEMENS 840 D total power requirement: 35 kW weight of the machine ca.: 7500 kg dimensions of the machine ca.: m E M A G (Germany) Vertical CNC Controlled Hard Turning and Grinding machine with tool turret and workpiece handling System Model VSC 250 DS Year 2004 # M7 28.69324 _______________________________________________________ Turning Ø, max. 250 mm Turning length internal / external 100 mm Workpiece length min./max. 29 – 100 mm 6-positon tool turret Ø / swing-Ø 480/790 mm Workpiece spindle Slide travel, X / Z / stroke 680 / 400 / 200 mm Feed rate / Quick feed X/Z 45/30 m/min. Feed force X/Z 5,5/11 kN Spindle speed 4.300 / 6.000 rpm Spindle drive 28 kW Total electrical load, ...
workpiece diameter: 250 mm centre distance: 0 mm honing length max.: mm max. module: 5 Gear Ø, min./max. 10 / 250 mm Module range 1 - 5 Length of teeth / max. table stroke 500 mm Height of centres of tailstocks 220 mm Max. weight of workpiece 50 / 100 kg Honing head swivelling +/- 35 ° Speeds of honing tool 20 - 500 rpm Size of honing tool, Ø x width 300 x 40 mm Workpiece speeds 500 - 3,000 rpm Total adjustment of cross slide 270 mm Rapid traverse of cross slide 50 mm Infeed travel of cross slide, mechanical 1 - 8 mm/Ø Roughing / finishing infeed 1 - 29 / 0.2 - 2.8 mm/sec Table speeds, hydraulic 0 - 6 m/min Total electrical load 5.5 kW - 380 V - 50 Hz Weight 3,200 kg Accessories / Special Features Working parameters can be preset using counters and control units. Automatic working process with workpiece counter. All roughing and finishing infeeds can be adjusted by a decade switch ...
honing diameter: 80 mm stroke: 280 mm throat: 300 mm total power requirement: 6 kW weight of the machine ca.: 2,6 t Honing Ø 10 - 100 mm Max. honing depth, approx. 250 mm Max. spindle stroke 260 mm Distance between spindle and column 300 mm Mounting height 1,000 mm Table size 350 x 500 mm Height of table above floor 500 mm Spindle speeds in 2 steps, infinitely variable, approx. 85 - 300 rpm 170 - 600 rpm Stroke speed, infinitely variable, hydraulic 0 - 23 m/min Spindle drive 2 kW Total electrical load 6 kW - 380 V - 50 Hz Weight 2,600 kg Accessories / Special Features Built-on 2-station tilting table which accommodates 2 workpieces. Mechanical workpiece clamping, using a manual lever. Hydraulic infeed of the tool. Switch-off via timer. Air measuring device (probably). Honing oil unit. Various splash shields, etc. Condition : Good. Machine can be in ...
faceplate diameter: 2500 mm swing diameter: 2865 mm turning height: 3000 mm Control: R & D type: MTC 4 Rest: 2 slide adjustment: 1500 mm turning speeds: 140 U/min tool change unit: 12 Pos. total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Machine is modernized The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was cre ...
grinding wheel diameter: 250 mm connected load frequency: 230 V : 90 - 180 U/min weight of the machine ca.: 18 Kg dimensions: 470 x 300 x 440 m Knife sharpening device with variable speed Grinding wheel 250 x 50 x 12mm, grit 220 Leather disc 200 x 30 x 12mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cutting diameter: 255 mm saw band length: 2765x 0,9 x 27 mm cutting width: 300 x 180 mm turning speeds: 35 + 70 U/min total power requirement: 1,8 kW weight of the machine ca.: 450 t dimensions of the machine ca.: 1,7 x 1,23 x 1,75 m SPECIAL PRICE! Double miter metal band saw, frequency converter hydraulic semi-automatic GBS 250 Super HA-I Easy • miter left 60° + right 45° • Material height sensor (automatic cut start detection) • Frame and gear made from one piece, very quiet cut and very low vibration • Hydraulic vice can be moved sideways a. • Guided, high quality industrial bearings • Solid vice + machine casting • Large machine bed • Machine base with tool compartment and chip drawer • Cut monitoring by ammeter • Cutting pressure feed regulator • Support roller (infeed side) • Ball bearing turntable Semi-automatic function: 1. Clamp material 2. Saw starts 3 ...
plate thickness: 3 mm blade length: 250 mm angle adjustable from - to: fest 90 Grad table surface area: 900 x 790 mm total power requirement: kW weight of the machine ca.: 0,65 t dimensions: 1,2 x 0,9 x 1,1 m Hydraulic notching machine - Footswitch - 2 pcs. sheet metal stop The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 2,5 kN stroke: 45 mm throat: 90 mm Working height from to: 80 - 220 mm table surface area: 120 x 60 mm weight of the machine ca.: 22 Kg dimensions: 160 x 230 x 390 mm Hand presses with rack HZ 250 The power is transmitted via a rack and pinion construction. she finds their use where during the working process a constant pressure is needed. Precisely manufactured, spindle hardened and ground, unlimited service life Long spindle guide, optimal pressure performance, T-slot according to DIN 650 milled in the middle, sliding blocks fit exactly. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cutting diameter: 250 mm saw band length: 3150 x 27 x 0,9 mm table height: 700 mm cutting width: 250 x 320 mm cutting speed: 25 - 90 m/min dimensions of saw-band: 2480 x 27 x 0,9 mm : 120 mm : 120 mm : 190 mm Impact energy: 190 mm connected load frequency: 400 Volt total power requirement: 1,5 kW weight of the machine ca.: 0,5 t dimensions: 0,95 x 1,16 x 1,98 m Rock-solid band saw for solid material - Double miter cuts up to 60° - AutoCut - Vice with quick clamping device - Belt tension control - Electric automatic cooling system - Material suggestion The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
saw blade diameter: 250 mm capacity 90 degrees: round: 80 mm capacity 90 degrees: square: 70 mm capacity 90 degrees: flat: 95x60 mm capacity 45 degrees: round: 70 mm capacity 45 degrees: square: 60 mm capacity 60 degrees: flat: 65x60 mm total power requirement: 1,0 kW weight of the machine ca.: 0,075 t dimensions of the machine ca.: 0,3 x0,8 x0,75 m SPECIAL PRICE! The ideal metal circular saw for workshop and assembly • For miter cuts left up to 45° • For sawing steel, stainless steel and, to a limited extent, aluminum profiles • Spindle vice with double clamping arm for low-burr cuts • Optionally with 230 V or 400 V motor • Automatic cooling directly on the saw blade • Double bearing for saw head • 24 V safety switch in the handle with restart lock • Length stop, assembly tool • Subframe (option) additional price 172,-EUR ATTENTION: Price is without saw blade! (saw bl ...
plate thickness: 8 mm blade length: 250 mm angle adjustable from - to: fest table surface area: 840 x 750 mm total power requirement: 3,0 kW weight of the machine ca.: 1,3 t dimensions: 1,4 x 1,1 x 1,5 m Hydraulic notching machine - Footswitch - 2 pcs. sheet metal stop The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Description: Suitable for dressing and profiling diamond and CBN grinding wheels. ccesories: Total enclosure., Motor Upgrade (stronger motors for the wheel being dressed and the dressing wheel),, Wheel motor strengthened to 4 kW,, Dressing wheel motor strengthened to 2,2 kW,, 2 Machine lights 12 V,, Optical linear scale with digital display counter (0,001 mm) X, Z Axes,, 2/3” TV Camera with 15” LCD monitor (microscope with zoom 15‐120X included),, High performance swivelling angle reader (0,05°),, Diamond / CBN wheel spindle speed stepless adjustable 100 - 1000 rpm,, Turning speed of dressing wheel stepless adjustable 200 - 2000 rpm,, Stepless oscillation speed,, Automatic central lubrication,, SIC Wheel dresser manual,, Grinding wheel holder:: HSK 50 E, Diamond grinding wheel diameter: 50 - 250 mm, max. width of grinding wheel: 70 mm, Grinding wheel bore diameter: 20 mm, Speed of ...
Machine designed for profiling and dressing flats, side, angular, radius and special shapes on diamond and CBN wheels. Especially suitable for single or multiple wheel packs., Accessories:, Motor Upgrade (stronger motors for the wheel being dressed and the dressing wheel),, Wheel motor strengthened to 4 kW,, Dressing wheel motor strengthened to 2,2 kW,, 2 Machine lights 12 V,, Optical linear scale with digital display counter (0,001 mm) X, Z Axes,, 2/3” TV Camera with 19” LCD monitor (microscope with zoom 15‐70X included),, High performance swivelling angle reader (0,05°),, Diamond / CBN wheel spindle speed stepless adjustable 100 - 1000 rpm,, Turning speed of dressing wheel stepless adjustable 200 - 2000 rpm,, Stepless oscillation speed,, Automatic central lubrication,, SIC Wheel dresser manual,, Protection cover., Specifications: Wheel spindle taper: HSK50E (alternatives possibl ...
Two Bosch vertical form fill and seal machines are available. 1) Bosch SVB 2501 A, year of manufacture: 1993, bag type: pillow bag, bag weight: 250g/500g, bag length range: 80mm-250mm, max. production output: 40 cycles/min, power consumption: 3kW, machine dimensions X/Y/Z: approx. 1300mm/2500mm/1700mm, weight: approx. 1100kg. Including clipping unit PS mako BS 600-CSP, year of manufacture: 2015. 2) Bosch SVB 3601 L, year of manufacture: 1996, bag type: pillow bag, bag weight: 250g/500g, max. bag length: 400mm, bag width range: 80mm-360mm, max. production speed: 40 cycles/min. Including clipping unit PS mako BS 600-CSP, year of construction: 2015, documentation available. On-site inspection is possible. Expected to be available from mid-January 2025.
For sale is a ProJet 2500Plus from 2017. The device is in perfect condition, test printing is possible (for an expense allowance, which will be offset against purchase)., Accessories: EasyClean System from 3D Systems, second build platform, Technology: MultiJet Printing
On behalf of a customer, we are selling a 3D Systems MultiJetPrinter type ProJet 2500Plus in very good condition. The machine was used as a dealer demo machine., The machine has been equipped with new drive belts and new filters. All materials have been removed according to the manufacturers instructions. The machine is empty. The printing time is approx. 1400 hours, 181,000 layers were printed with approx. 24KG of building material and approx. 33KG of support material., Equipment:, - 3D Sprint Basic Complimentary Software (on-line activation), Installation: 2016, Print modes: HD - High Definition, Net build volume (xyz) net build volume (xyz) hd mode: 294x211x144mm / 11.6x8.3x5.6in, Resolution (xyz) resolution (xyz) hd mode: 800x900x790 DPI; 32μ (0.0012 in) layers, Accuracy (typical): ±0.025-0.05 mm per 25.4 mm of part dimension. Accuracy may vary depending on printing parameters, ...
A new belt roasting machine for nuts in the food industry is available. Fuel: diesel/electricity/gas/LPG, output: 2kW, machine dimensions X/Y/Z: approx. 3600mm/1900mm/1950mm, operating hours: 31h. Roasting capacity per hour: hazelnut kernels: 160kg, shelled peanuts: 150kg, shelled peanuts: 35kg, shelled pistachios: 90kg, sunflower seeds: 70kg, pumpkin seeds: 70kg, almonds: 120kg, cashew nuts: 150kg, chickpeas: 120kg. Including salt kettle with a capacity of 35kg and fully automatic high-pressure belt washer. Documentation available. On-site inspection is possible.
pressure: 250 t distance between columns: 600 mm stroke: - mm total power requirement: 22 kW weight of the machine ca.: 9 t dimensions of the machine ca.: 2 x 2 x 3,2 m No. 3421 Mould press 2500 / 700 kN Single stroke 2-hand Single stroke foot switch Automatic continuous run set-up and tipping Table 500 x 500 Working range: Pressure capacity 250 tonnes Drive: ^22 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bore capacity in steel (diameter): 55 mm arm length: 2500 mm workpiece height max.: - mm total power requirement: 8 kW weight of the machine ca.: 5 t dimensions of the machine ca.: 4 x 1 x 3 m Radial drilling machine MK 5 Spindle holder MK 5 Speed range 30 - 1500 min-1 Feed rates 0.05 - 0.6 mm/rev Space requirement approx. 3.7 x 1 x 3 m Weight approx. 5 tonnes (estimated) Working range: MK 5 x 2500 Drive: 3.7 / 6 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
carrying capacity: 250 kg number of suction cups: 6 suction cup dia.: 215 mm Vacuum lifter VH 6-250 for the horizontal transport of smooth, dry and airtight panels. Robust supporting structure made of steel, painted in RAL 2000 with low Own weight. consisting of: - 1x galvanized longitudinal beam with a length of 2,400 mm - 3x galvanized crossbeams with a length of 1,000 mm - 6x Springy, articulating and adjustable suction cup holders - 6x suction cups Ø 215 mm, the seal can be separated in case of wear whose metal supports can be changed inexpensively and without tools - 6x ball valves to switch off individual suction cups, thus also smaller formats can be lifted without having to move suction cups or traverses. - 1x spiral connection cable small helix: with an extension length of 3,500 mm, designed as an extension cable with CEE plug and coupling. is routed to the lifting device nex ...
cutting diameter: 255 mm saw band length: 2765 x 27 x 0,9 mm table height: 950 mm : 18-110 m/min : 255 mm capacity 90 degrees: square: 240 mm capacity 90 degrees: flat: 300 x 180 mm capacity 45 degrees: round: 210 mm capacity 45 degrees: square: 190 mm capacity 45 degrees: flat: 200 x 160 mm capacity 60 degrees: round: 135 mm capacity 60 degrees: square: 110 mm capacity 60 degrees: flat: 130 x 100 mm capacity 45 degrees: round: rechts 180 mm capacity 45 degrees: square: rechts 160 mm capacity 45 degrees: flat: rechts 180 x 100 mm : 1,5/1,8 kW : 350 kg : 1700 x 900 x 2000 mm Manufacturer no. 20437 Description: - Miter cuts left 60° and right 45° - Quick-action clamping stick can be moved in the T-slot for quick position changes - Hydraulic brake cylinder - Large ball-bearing turntable for easy miter adjustment (durable) - Chip clearing brush - Machine base with automatic cooling system ...
control: MAZAK Mazatrol 640T Nexus swing over bed: 610 mm swing diameter over bed slide: 350 mm turning length: 982 mm c-axis: indexing: 0.001 ° turning speeds: 4000 U/min tool taper: ASA A2-8 tailstock quill taper MT: 5 rapid traverse X-axis: 30 m/min rapid traverse Z-axis: 33 m/min Overall size: 4500 x 2000 x 1600 mm weight of the machine ca.: 6.5 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
drill diameter: 2-40 mm drilling length: x mm lip angle: 40-180 ° weight of the machine ca.: 0.4 t Dressing device Point thinning attachment More details on www.marcels-maschinen.ch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Sumbel Enano 250 banding machine; cleaned and tested; Working width 250mm; suitable for cold glue; was overhauled in 2010. Gluing machine Sumbel Enano 250; cleaned and checked; woking width 250mm; used for cold glue; Rebuilt in 2010.
We currently offer: Number 001 Generator set Type: IL 250-4 Engine Iveco Generator LeRoy Somer Power: 250 KVA Year of construction 2002 Hz 50 IP 23 AVR Regulator R448 Hours 299 Metrics: L: 5.10m H: 1.90m B: 1.00m Weight: 2800 kg Accessories: Control cabinet You can find more machines on our website. If you have any further questions, please feel free to contact us. Adel e.K. Commercial Vehicles-Construction Machines Car Recycling Machine Dismantling Gottlieb-Daimler Str. 26 D-74831 Gundelsheim Phone: 0049 1796710242
Manufacturer: Sysmex Model: CS 2500 Year of Manufacture: 2012 The CS-2500 is a fully automated, high-performance hemostasis analyzer designed for advanced laboratory needs. Utilizing multi-wavelength technology and PSI™ checks, it delivers precise results for coagulation, chromogenic, immunoturbidimetric, and aggregation testing—all in full random access. Compact and efficient, this benchtop system is an ideal solution for mid- to high-volume laboratories. Find more here - / Contact us at -
Linear weigher with 100g up to 10,000g weighing range. Weighing/dosing of granular and chunky products. 2 weighing heads with load cells and 2 vibrating feeders allow fast and precision weighing. - Specifications: capacity weighing hopper: 20 L | number of weighing heads: 2 | weighing range: 100-10,000g | accuracy: +/- 1-25g | max. speed of the machine in neutral: 20 cycles/minute | power: 220V, 1-phase | stainless steel version SUS 304. That machine/system is available in different versions for different packaging sizes and with different packaging speeds. Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo a ...
High-speed Metal Detector for the use in high-speed production lines, stainless steel framework, touch screen. - Specifications: detecting speed 0.2-1.7m/sec | detecting accuracy: FE from ? 0.8mm, SUS from ? 1.8mm | tunnel size WxH: 300x120mm | max. passing size WxH: 250x80mm | power: 220V/0.3kW, 50Hz/60Hz | dimensions and weight: L1505xW600xH890mm, 150/250kg. Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo are possible. - All machines are available with full warranty.
Metal Detector for food and other (e.g. medical, chemical, textile) products, also suitable for wet products, stainless steel framework, touch screen, easy integration into existing production line. - Specifications: weight of the product: max. 5kg | detecting speed: 0.5m/sec | detecting accuracy: FE from ? 1.5mm, SUS from ? 2.0mm | tunnel size WxH: 125x250mm | max. passing size WxH: 100x215mm | power: 220V/0.3kW, 50Hz/60Hz | dimensions and weight: L1627xW528xH1420mm, 110/210kg. Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo are possible. - All machines are available with full warranty.
Vacuum conveyor with electric vacuum pump. - Specifications: capacity: 1500-2500kg/h (with max. 5m conveying distance) |housing: stainless steel 304 | required compressed air: 0.6 MPa | air consumption: approx. 60L/min | power supply: 220V | power consumption: 7.5kW. Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo are possible. - All machines are available with full warranty.
X-ray inspection system for small single bags, packs. Suitable for detecting foreign objects made of metal, glass, stone, plastic, etc. in food or non-food items. - Specifications: conveyor belt width: 250 mm | detection accuracy: Pb from ? 0.2 mm, Fe from ? 0.28 mm, SUS from ? 0.28 mm, non-metallic such as stone, glass, from ? 1.2 mm | X-ray output: 80 kVp, 1.25 mA | X-ray detector resolution: 0.4 mm | X-ray emissions: < 1usv/h | X-ray beam: horizontal scan | conveyor belt height: 850 ? 30 mm | conveyor speed (dependent on product dimensions): 10 ? 100 m/min | screen: 15 touch screen | software: intellisens?X-ray | operating temperature: 5 ? 35 ?C | reject system: optionally available according to requirements | power: 220VAC, 50/60Hz | dimensions of the system: L800xW860xH1580 mm | weight: 270 kg. Please note that our new prices are often below the usual used prices. Please feel free t ...
Manufacturer: Arburg Model: 320C / 600-250U Year of Manufacture: 2010 Specifications: - Clamping Force: 60 tons - Screw Diameter: 30 mm - Operating Hours: 59,165 - Cycles: 2,140,296 Find more here - / Contact us at -
MUNK Günzburger Steigtechnik 303406 Aluminum access ladder machine crossing with platform (bridge) 1900-750-2500 RA2414 Technical data: Manufacturer: Munk Günzburger Steigtechnik Type: machine crossing with pedestal Condition: very good (used) Total size: 1900-750-2500 mm (WxDxH incl. handrail) step dimensions: 85 x 600 x 45 mm step/tread height: 230 mm platform dimensions: 800 x 650 mm Platform height: 1350 mm bottom edge 1420 top edge Steps: 6 (5 steps + platform on each side) Maximum working height: 3450 mm maximum load: 150 kg Weight: 38 kg Price plus VAT ex central warehouse Dr. Sonntag GmbH & Co. KG 97076 Würzburg Features: For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Your team at Dr. Sonntag ...
pressure: 250 t throat: 400 mm stroke: 30...140 mm table-size: 1000 x 750 mm hole in the table: 360 x 400 mm ram surface: 630 x 500 mm ram adjustment: 110 mm total power requirement: 18 kW weight of the machine ca.: 16 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
plate width: 2500 mm sheet thickness - max.: 32 mm sheet thickness - max.: 39 mm sheet thickness - min.: 8 mm bale length: 2700 mm number of straightening: 7 Rollers number driven straightening rollers: 5 Stk straightening roll diameter: 290 mm diameter of input / output straightening rollers: 345 mm number of support rollers: 13 Stk diameter of support rollers: 288 mm stroke of upper beam: 120 mm straightening feed: 16 m/min rated power of main drive: 90 kW : 138 kw weight: 79 t - max. sheet thickness( St 50): 32 mm - max. sheet thickness( St 34): 39 mm - min. sheet thickness( St 50): 8 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll diameter: 250 mm roll length: 500 mm rolls drilled: peripher Nip adjustment: hydraulisch total power requirement: 2x 5,5 kW Condition: new rolling mill, with CE marking, with 2 year warranty Specification: Monobloc laboratory rolling mill 250 x 500 mm - new - roll diameter: 250 mm - Roll length: 500 mm - Roll bore: peripherally drilled - Single drives: variable friction ratio - Roller bearing: roller bearing with manual grease lubrication - Gap adjustment: hydraulic - new hydraulic unit for roller nip and emergency system - New rotary unions make Johnson-Fluiten - two adjustable guide plates to adjust the working range on the rollers. - Working range approx.: 100 to 460 mm - Roller gap, during the working phase 25 mm - tiltable guide plates made of nylon-polyethylene Material - Stainless steel tank - New saf ...
pressure: 250 t throat: 360 mm Table dimensions: 1250 x 630 mm table diameter: 250 mm dimension of ram: 850 x 450 mm dayligth: 800 mm piston stroke: bis 500 mm diameter of piston: 400/360 mm ram stroke speed: abwärts 200 mm/sec ram stroke speed: aufwärts 110 mm/sec total power requirement: 20,5 kW weight of the machine ca.: 8 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 600 mm y-travel: 400 mm z-travel: 500 mm total power requirement: 6 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
I am selling this machine. Plugged in, can be tested. Very good condition. Documentation for the machine. Can be sent via whatsapp video of the machine
Manufacturer: Arburg Model: ALLROUNDER 630 S 2500 – 675 Year of Manufacture: 2003 Technical Specifications: - Operating Voltage: 400 V, 3-phase, 50 Hz - Control Voltage: - 230 V AC, 50 Hz - 24 V DC - Motor Heating Rated Current: 113.0 / 33.0 A - Total Rated Current: 146.0 A - Total Connected Load: 83.0 kW - Tie Bar Distance: 630 mm - Clamping Force: 2500 kN - Screw Diameter: 45 mm - Max. Part Weight (PS): 252 g - Core Pull: Yes (1 unit) - Orientation: Horizontal - Number of Components: 1 - Drive Type: Hydraulic - Robot Operating Hours: 110315 (automatic operation) Find more here - / Contact us at -
Used CIP system: 2 x 2500 litre stainless steel tanks For sale is a used CIP system with two 2,500-liter tanks. This clean-in-place system is the ideal solution for the automated and hygienic cleaning of your production systems in the food industry, beverage industry or even in the pharmaceutical sector. Two separate stainless steel tanks (2,500 litres each) Made of stainless steel (V2A)
Leather goods wrapping machine with various tools up to approx. A6
maximum number of results exceeded
please refine your search
