2000 ton hyd used for sale

Hydraulically switchable gearbox for change of direction of rotationHydraulic reverse gear of latheYear of construction approx. 1985Alternating gearbox for fast change of direction of rotationClockwise or counterclockwise rotation- electric hydraulic pump for hydraulic pressure generation (380 volts, 0.25kW)- 2 pieces of solenoid valves for switching from left to clockwise rotation- equipped with pulleys 230 and 200 mm- was driven by a 15 KW drive motor, fast change of direction of rotation with high torque transmission- Drive motor always runs on the right, gearbox is hydraulically activated

Hydraulic Machine Vise ARNOBock width: 200 mmJaw height: 60 mmClamping force: 8 ton. Clamping range: 0 to 370 mmOpening width: max 373 mmGuideway height: 140 mm- 2 clamping ranges adjustable via plug-in pins- TurntableDimensions L x W x H: 900 x 400 x 210 mmWeight: 125 kgGood condition; used

Hydr. Scissor lift table TREPEL - L. A. VAN EIJLE & Co.Year of construction approx. 1980Load capacity approx. 5 ton. Platform size 1700 x 1100 mmStroke max. 515 mmOverall height Table bottom with rail rollers 535 mmOverall height Table bottom without rail rollers 480 mmTable height raised with rail rollers max. 1050 mmTable height raised without rail rollers max. 995 mmTravel speed rail chassis approx. 8.5 meters/min. Motor power 4 kWNet connection 400 volts, 50 Hz hand switch for up and down on the cable safety limit switch

Hydraulic self-centering steady rest, luenette, Lynette SMW AUTOBLOKHydraulic steady rest with hydrostatic bearingSuitable for GILDEMEISTER / MAX MÜLLER lathe MD 5 Type: SLK 8-70 NSpanning range: 8 to 70 mmOperating pressure: approx. 60 barBezel foot: 245 x 240 mmDesign: fixed- 3 pieces roller bearing 35 mm- Roller width 18 mm- hydraulically self-centeringDimensions L x W x H: 350 x 250 x 550 mmWeight: 65 kgGood condition; used

Hydraulic guillotine shears STEINER type HTS 30/20 RMasch. No. 315 Year of construction 1982Cutting length 3050 mmCutting thickness 20 mmBack gauge 800 mm controlledMotor power approx. 30 kWNet connection 400 volts, 50 Hz- Back gauge with positioning control ELGO- Back gauge adjustment via ball screws- Safety light barrier SICK front as protection against interference- 3 pieces Material Support arms with ball rollers- Electric foot switch- Replacement knifeSpace requirement of the basic machine L x W x H 4650 x 2610 x 3200

Single column hydraulic press, straightening press, punching bracket ECKOLDPressen frame with hydraulic cylinder, mobile press, punching unitType RSD 1500 - 125Masch. No. 317 / 690 Year of construction approx. 1986Compressive force 150 ton. Projection 125 mmSlide stroke 35 mmTable size 280 x 210 mmPlunger area 125 mmInstallation height (plunger to table) max. 265 mmTable height above floor 403 mmHydraulic operating pressure max. 500 bar- without hydraulic unit- Lifter surface with 4 threads M16 and 20 mm guide groove, one centering hole in the middle 15

Rotary indexing table, rotary indexing table with 16 stationsRotary transfer machine + hydraulic press TOXRundtaktautomat Special machine with several assembly stationsProduction and assembly system in rotary transfer processFrom special machine manufacturer AKE-technologies GmbHSerien number: 01-45-064Order number: 11111Year of construction: 2012- large rotary indexing table WHITE type TC500, with 16 stations- pressing station with TOX powerhouse- vibation conveyor- conveyor belts- test stations - some stations still open

Single column hydraulic press SCHÖN type TES/CBbuilt in 1977Compressive force 63 ton. (160 bar)Projection 320 mmTable size 600 x 770 mmPlunger area 600 400 mmPlunger stroke 125 mmInstallation height max. 400 mm (with intermediate plate on the ram)Slide speed Rapid traverse downwards approx. 180 mm/sec. Ram speed work approx. 25 mm/sec. Pushrod speed upwards approx. 180 mm/sec. Table height above floor 870 mmDrive power 22 kWNet connection 380 volts, 50 HzTank capacity approx. 280 litres Hydraulic oil

Single column hydraulic press SCHULZ type SES 250Masch.Nr. 04.86.3511/3 Year of manufacture 1986Compressive force 25 ton. Retraction force 10 toProjection 360 mmTable surface 600 x 720 mmPlunger area 500 x 500 mmFailure opening in table 100 mmPin hole 40 mmPlunger stroke 400 mmInstallation height max. 600 mmTable height above floor 935 / 775 mmTank capacity hydraulics 380 litresDrive power 7.5 kWNet connection 380 volts, 50 Hz- Fixed stop adjustment in the press cylinder 180 mm- Light barrier

Hydr. Scissor lift table WEIDMANN type E5/13-1Fabr. No. 30403339 Year of construction 1982 / 2007Load capacity 500 kgPlatform size 2000 x 1200 mmStroke max. 1280 mmOverall height - table bottom 290 mmOverall height - table top max. 1570 mmTable height with safety support 1430 mmLifting speed 1280 mm in 25 sec. Lowering speed 1280 mm in approx. 0 to 15 sec. Hydraulic operating pressure approx. 130 barEngine power 1.5 kWNex connection 400 volts, 50 Hz.- Rotary switch switch on the hydraulic power unit for up and down lowering speed

Hydr. Press brake, die bending machine HAMBURGER JONESCHEIT type HYPM 70-2600Fabr. No. 4004 Year of construction 1987Printing capacity 70 ton. Working length 2600 mmStand width 2770 mmPlunger stroke 60 mmDistance table - ram max. 390 mmTable size 2750 x 200 mmMotor power 7.5 kWWet connection 380 volts, 50 Hz.- Crimping depth via mechanical fixed stop with electric adjustment and mechanical depth indicator- Lower tool consisting of 2 segments, each 835 mm, with 2 different prisms (15 and 24 mm)- Upper tool,

Hydr. Swing cut guillotine shears HERA type HSS IIIFabr. No. 598 Year of manufacture 1986Cutting length 3100 mmCutting thickness 3 mmStand projection 200 mmKnife strokes 25 strokes/min. Mains connection 380 Volt, 50 HzMotor power 3 kW- motorized adjustable back gauge 1070 mm- actual digital display for the back gauge- cutting gap adjustment- cutting length adjustment- front side stop left 1000 mm- 4 pieces sheet metal support arms 1000 mm- el. Foot switchSpace requirement without sheet metal support arms L x W x H 3630 x

Hydr. Hacksaw, hacksaw, lifting saw KASTO type PSB WBS 210 / 230Masch. No. 115 106 1212 / 72783 Year of construction 1986Sawing area - Round 250 mmSawing area - Square 225 x 225 mmSawing area - Rectangle 260 x 100 mmCutting speed 11 -13 - 17 - 22 - 26 - 34 m/min. Saw blade length 400 mmMotor power 1.4 and 1.8 kW pole-switchableMains connection 380 volts, 50 Hz- only for 90 cuts, no mitre adjustment- Saw motor with 2 speeds and 3 V-belt steps- Hydraulic saw bar feed- hydraulic

Hydraulic Cylinder Double-acting HÄNCHEN Type ServoslideFlange Cylinder, Ideal for Workshop PressSeries No.: S004420 Year of Manufacture 2010Cylinder Stroke: 400 mmOperating Pressure: 300 barPiston Rod: 160 mmPiston Diameter: 220 mmCylinder Press Force at 300 bar: 114 Tonflange Outer Diameter: approx. 400 mm with 16 Bores 24.5 mmTotal Length Piston Rod Retracted: approx. 1230 mm (with the Wheel Measuring Cell)Total Length from Flange to Cylinder Upper Edge: approx. 750 mm- Hydraulic Connection Thread G 1 1/4 - Thread on the piston rod M150 x 3 mm

Hydr. Hacksaw (Made in Croatia) Type BS 320Year of construction approx. 1980Saw range Round 320 mmSaw area Square 280 x 280 mmSaw blade 550 x 45 x 2.25 mmMaterial Inlet height 680 mmSaw speed 42 - 55 - 85 - 110 strokes/min. Motor power 1.8 and 2.4 kW Pole switchableMains connection 400 volts, Hz- Mitre adjustment up to 45- Saw motor with 2 speeds and 2 V-belt steps- Hydraulic saw bracket lowering- Hydraulic cutting pressure adjustment via throttle valve- Coolant device in the

Hydraulic punch, punching rack for the use of punching units JOKA type HP-SHydraulic hole punch, hydraulic press for punching bracketYear of construction approx. 1995Printing capacity 5 ton. Projection 155 mmStroke approx. 20 mmPunching unit width max. 54 mmPunching unit height max. 220 mmDie holder 48 mmMotor power 1.5 kWNeching connection 230 volts, 50 Hz- for the universal use of punching units JOKA SW 20 or SWD 20- Projection of the punching units can be larger, can be pushed through to the rear- Stroke release via

Hydraulic power unit for mobile clinching pliers or mobile former ECKOLD type HA 500 / 2Fabr. No. 737 / 783 Year of construction 1991Hydraulic power unit type HA 500 / 2Operating pressure 50 - 500 bar adjustableFlow rate 2.6 l/minTank capacity 16 litresEngine power (hydraulic) 3 kWNead power 380 Volts, 50 Hz.Control voltage 24 Volts, DC pressure line with screw coupling- With solenoid valve HAWE GS 2-2- mobile on 4 swivel castorsWeight without hydraulic oil 125 kggood condition; used

Hydr. Flat-form scissor lift table FLEXLIFT FLUNDER type 1500 / 100 (without hydraulic unit)Year of construction 1991Nominal load capacity 1500 kgLifting capacity (practically tested) 1000 kg (at approx. 350 bar)Platform size 2100 x 1400 mmStroke max. 930 mmOverall height - bottom 100 mm (with mounting frame)Overall height - top 1030 mmHydr. Operating pressure 350 bar = lifting capacity 1000 kgHydraulic engine power 1.5 kWNerg connection 400 volts, 50 Hz- mechanical-hydraulic safety limit switches stop the lowering process when the safety strip is operated -

Hydr. Notching machine with angle adjustment SIMASV type AV 220-6PAFabr. No. C1524 Year of construction 1996Knife length 220 mmMaterial thickness for steel 6 mmMaterial thickness for stainless steel 4 mmTable dimensions 950 x 790 mmTable height 940 mmMotor power 3 kWNet connection 400 volts, 50 Hz- Operation via tactile switch or foot switch- Adjustable notching angle from 30 to 140- Angle adjustment via 2 hand cranks for right and left- Hydraulic clamping for the adjustment blade- Electric foot switch- 2 pieces

Hydraulic guillotine shears FASTI type 509 - 25/4Masch. No. 5418 Year of construction 1991Cutting length 2535 mmCutting thickness 4 mmBack gauge 5-1000 mm (controlled)Cutting angle adjustableHydraulic pressure max. 290 barMotor power 7.5 kWNeching connection 400 volts, 50 Hz- Back gauge with positioning control ELGO ELECTRIC Type 85- Sheet metal holding device under the back gauge- Manual cutting gap adjustment with dial gauge display on the right and left- Stepless cutting length adjustment- Hydraulic

2-column hydraulic press SELF-MADEBaucy approx. 1980Compressive force 6 ton. at 180 barCompressive force 5 ton. at 150 barCompressive force 4 ton. at 120 barCompressive force 3 ton. at 90 barTable top 400 x 340 x 30 mmPlunger plate 410 x 350 x 28.5 mmTable usable area between the guide columns 305 x 245 mmPlunger stroke 140 mmInstallation height max. 320 mmColumn diameter 35 mmTable height above floor 1050 mmHydraulic operating pressure max.180 barMotor power 4 kWNet connection 380 volts, 50 Hz- stepless

Key data: 4040 mm, 4 mm

Max. cutting length: 4040 mm Max. sheet thickness: 4 mm steel Motorized adjustable backgauge with digital display up to 1000 mm Pneumatic sheet hold-up Side stop and table extensions Cutting length limitation Cut edge lighting Weight approx. 7500 kg

Key data: 5 t, 150 mm

Hydraulic Press Atsugi AP-5-KL Used Load Range: 20-50 (kN) Stroke (mm): 150 Lower Speed ​​(Approach Fast Speed: 350 (mm/s) Lower Speed ​​(Under Pressure Slow Speed: 36mm/s Rise Speed ​​250 (mm/s) Working Area Open Height: 250mm Open Depth: 180mm Table Size: 450x50mm Motor Specification 3 Phase AC200V 4P 1.5KW Two-Hand Operation . Mobile Worktable Fuel Oil / Quantity Daphni Hydraulic 46/9L Total Weight (kg) 270 Body Size ​ Height (mm) 986 Width (mm) 485 Depth (mm) 920

Max. cutting length: 3100 mm Max. sheet thickness: 6 mm at 490 N/mm² Motorized backgauge with digital display Manual cutting gap adjustment Cutting length variably adjustable Cut edge lighting New knives

Key data: 3190 mm, 6 mm

Note: Machine is currently still being revised, the illustrations were made before the Revision. Sheet width: 3190 mm Sheet thickness steel: 6.3 mm Colour: grey Total power requirement: 18.5 kW Machine weight: 6800 kg Dimensions: 3830 x 3820 mm with cutting gap adjustment Stroke rates per minute: 30 - 50 strokes/min Angle stop: 1500 mm Throat: 5 - 1000 (1500) mm

CONTROLS   PC controller BECKHOFF PRESS DESIGN   drive system: servohydraulic   frame design: H-frame, tie rod   quick die change system: yes   feedstock transport direction: left to right SLIDE   total force (nominal): 1100 to   stroke: 130 mm   stroke rate (max.): 60 /min COUNTER RAM   nominal force: 330 to   stroke: 40 mm V-RING   nominal force: 500 to   stroke: 40 mm TOOL DIMENSIONS   lower table (left-right): 960 mm   lower table (front-back): 960 mm   upper table (left-right): 960 mm   upper table (front-back): 960 mm   shut height max.: 470 mm OVERALL SPECIFICATIONS (COIL LINES)   sheet width max.: 500 mm   sheet thickness max.: 16 mm   coil weight max.: 8 to   feedstock transport direction: left to right COIL CHAIR   coil weight max.: 8 to   stroke: 700 mm DECOILER   coil weight max.: 8 to   max. diameter of coil: 1800 mm   m ...

sheet width: 3100 mm plate thickness: 6,0 mm thickness at Niro-steel: 4,0 mm distance between columns: 3100 mm down holder: 14 Stück oil volume: 150 ltr. cutting angle: 1,2 ° no. of strokes: 18 Hub/min control: CYBELEC CybTouch total power requirement: 11,0 kW weight: 6300 kg range L-W-H: 4.000 x 2.100 x 1.640 mm -------------------------------------------------- electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment -------------------------------------------------- Furnishing: - CNC electr. / hydraulic swing cut shears - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Quantity Cutting length limitation Material preselection, including sheet thickness Cutting line lighting - motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. Can be fol ...

pressure: 80.0 t stroke: 250 mm table surface area: 1040 x 260 mm column travel between the guideways: 1040 mm ajustment speed: 8.0 mm/sec working feed: 5.0 mm/sec return speed: 10.0 mm/sec engine output: 5.5 kW weight of the machine ca.: 835 kg. dimensions of the machine ca.: 1810 x 700 x 2100 mm Furnishing: - Robust electro-hydraulic workshop press, with fixed cylinder - Ideal for aligning axles, shafts, etc., but also for pressing in and out of bolts, bearings, bushings and much more. - Robust welded steel construction for high demands - Table height adjustment via piston rod including round steel chain and 2x locking bolts Piston rod with metric socket - 1x set of V-block prism supports - Manometer for pressure display - simply constructed hand control with: 1x delivery speed 1x working speed 1x retreat speed - Piston can be stopped in any position - Hydraulic tank mounted on t ...

pressure: 20,0 t stroke: 185 mm table surface area: 170 mm Breite column travel between the guideways: 510 mm weight of the machine ca.: 112 kg dimensions of the machine ca.: 1630 x 560 x 730 mm Furnishing: - Standard with pressure cylinder that can be moved to the left and right - For aligning, pressing, bending, assembling gears, discs, etc. - Standard with foot pedal and hydraulic hand pump for piston delivery - Standard with support prism for aligning shafts - With automatic piston retraction by integrated return spring as standard - Height-adjustable press table with locking bolts - Large manometer for reading the compressive force - Including two-stage hydraulic pump - Robust construction with welded steel frame The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 30 t stroke: 150 mm table surface area: 185 mm Breite column travel between the guideways: 530 mm weight of the machine ca.: 162 kg dimensions of the machine ca.: 800 x 700 x 1805 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 50 t stroke: 200 mm table surface area: 730 x 205 mm dayligth: 1050 mm column travel between the guideways: 730 mm weight of the machine ca.: 288 kg. Description : - Standard with cable winch - for easy height adjustment of the support table - Piston delivery either manually or pneumatically - Powerful workshop presses for craft and repair businesses - Optimum price-performance ratio thanks to rational design - The standard foot pedal keeps your hands free for the workpiece - Increased range of application thanks to the optionally . available pressure mandrel set (10 pieces). - Pressure cylinder with integrated return spring for piston return - Welded steel frame for heavy use and high stability - Versatile in use thanks to the pressure cylinder that can . be moved to the left and right The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3100 mm plate thickness: 6,0 mm distance between columns: 3.100 mm down holder: 14 Stück no. of strokes: 16 - 24 Hub/min oil volume: 150 ltr. cutting angle: 0,5 - 1,5 ° thickness at Niro-steel: 4,0 mm column arm: 350 mm engine output: 11,0 kW weight of the machine ca.: 7.060 kg range L-W-H: 4100 x 2200 x 2190 mm -------------------------------------------------- electr. / hydraulic CNC guillotine shears - guided by a backdrop with CYBELEC CNC touch screen control with electr. / hydr. Cutting gap and cutting angle adjustment -------------------------------------------------- Furnishing: - CNC guiding guillotine shears - with electr. / hydr. Cutting gap and cutting angle adjustment - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including s ...