2000 kw gas used for sale

2 Kuka for floor mounting, payload 150kg, weight approx. 1280kg 1x Type KR150 L110-2 2000 1x Type KR150 L130-2 2000

General SKU295P584 MakeGerald Kainz Verfahrenstechnik GmbH (DE) TypeGTS-2000 No.18/027 Year of construction2018 LocationBarneveld Main Features MaterialMild steel Surface2.6 m2 Sizes diameter1880 mm Specified Features - Tumbler screener MaterialMild steel Tumbler screening machines Vibro sieveTumbler screening machine Sieve surface2.6 m2 Number of sieve decks:1 Sieve sizesdia.1880mm With covercheck Inletdia.300mm Outletdia.200mm Drive excentercheck Motor4,0 KW, 400/690 Volt Sieve perforation(no sieve) Information Mounted on mild steel framecheck Floor space2,0x2,0 M Total height1,8 M Weight1150 KG Extra SpecificationsThis sieve is unusedTumbler screening machinesKainzSieves > Tumbler screening machinesBrand > Kainz What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination ...

SUNNEN ML2000, Honing Diameter Range:, - Manual Stroking: 1.5 mm to 165 mm, - Power Stroking: 1.5 mm to 102 mm, Spindle Speed:, - Infinitely variable from 200 to 3,000 RPM, Stroke Rate:, - 60 to 350 strokes per minute, Automatic Sizing Range:, - 3 mm to 51 mm, Oil Tank Capacity:, - 106 liters, Pneumatic Requirements:, - 5.5 bar, Machine Dimensions:, - Length: 1,600 mm, - Width: 1,220 mm, - Height: 1,900 mm, Weight:, - Approximately 725 kg

Whirlpool Vessel, fitted with stainless steel hinged lid. Approx. 2000Litres Tangential inlet with 1.5" RJT male inlet point. Three separate take off points with 1.5" RJT male butterfly valves. Insulated and clad in fully stainless steel. This is a SECOND HAND item and is sold as seen For more information and more available stock please visit us at - advancedbrewing.co.uk

This CHIRON MILL 2000 Vertical Machining Center was manufactured in the year 2003. It is equipped with a Siemens Sinumerik control unit. The machine has a spindle speed of 12000 rpm.

Subj.: Offer about second-hand cut-to-length line Dear Mr Rajput, We have pleasure to provide you with an offer about second-hand cut-to-length line that is immediately for sale. Qty. 1 Second-hand cut-to-length line Mfc.: SACMA, UWM Built: 1994 Material: Stainless steel Strip Width: max. 2000 mm Thickness: 3.0 – 8.0 mm De-coiler Coil weight: 25,000 kg max. Leveller: 13 rolls, dia.: 130 mm Guillotine: start / stop type, manufactured by SACMA, Paper / cellophane feeder Stacker Run-out table Dimensions: 34 x 8 m Speed: 30 m/min

Stainless Steel Vertical Cylindrical Tank 2000L. Single skin with side entry manway and top inspection port. Lifting eyes Sight level gauge. Sample Tap Racking point with valve. Bottom outlet with DIN40 butterfly valve. This is a SECOND HAND item and is sold as seen For more information and more available stock please visit us at - advancedbrewing.co.uk

This TORNOS DECO 2000/13 was manufactured in 1999. It features a bar passage of 16 mm and supports up to 20 fixed and 16 rotating tools. Equipped with an IEMCA loader, CONVEYORS IND. ASS. conveyor, and additional oil filter tank, this machine ensures efficient operation. Consider the opportunity to buy this TORNOS DECO 2000/13 swiss type turning machine. Contact us for more information about this machine.

This DMC US 2000 M4 belt sander was manufactured in 1999. Ideal for detailed sanding work, it offers precision and efficiency. Consider the opportunity to buy this DMC US 2000 M4 belt sander. Contact us for more information.

This 3-axis NILES DLZ 630 V x 2000 was manufactured in 1983. It features a turning diameter over bed of 630 mm and over support of 340 mm, with a turning length of 2000 mm. The spindle speed ranges from 22.5 to 1120 rpm across 18 steps. Total power requirement is 15.0 kW, and it includes multiple steady rests and face plates. If you are looking to get high-quality turning capabilities consider the NILES DLZ 630 V x 2000 machine we have for sale. Contact us for more information.

This 3-axis MORI SEIKI NL 2000 SY/500 was manufactured in 2005. A horizontal turning machine featuring a BF interface and live tools, it also includes a tool setter on both spindles. If you are looking to get high quality turning and milling capabilities consider the MORI SEIKI NL 2000 SY/500 machine we have for sale. Contact us for more information.

This FANUC M-2000iA/1700L was manufactured in 2018. A robust and reliable piece of equipment, its ideal for those looking to enhance their automation capabilities. Consider the opportunity to buy this FANUC M-2000iA/1700L. Contact us for more information.

This 3-axis DAEWOO PUMA TT 2000 SY was manufactured in 2005. It features a turning diameter over bed of 800 mm and a maximum bar diameter of 65 mm. Equipped with a Fanuc 18i-TB control system, it offers spindle speeds up to 5000 rpm and includes a tool turret with 12 stations. Consider the opportunity to buy this DAEWOO PUMA TT 2000 SY horizontal turning machine. Contact us for more information about this machine.

Dear Sirs, We are pleased to offer the following Used Open Die Forging Press, manufactured by Kawasaki (Japan), a well-known and reputable Japanese OEM. EQUIPMENT OVERVIEW Equipment: Open Die Forging PressManufacturer: Kawasaki (Japan) Manufacturing Year: 2012 Condition: Used, in production until May 2025 Application: Forging of rings and heavy forged components The press owner supplied forged parts (mainly rings) for power plant applications to leading OEMs such as Mitsubishi, Toshiba, GE, Hitachi, Fuji, etc. TECHNICAL SPECIFICATIONS General Press Capacity: 2,000 ton System Pressure: 30.0 MPa Pulling Capacity: 1,000 kN (100 ton) at 19.5 MPa Number of Cylinders: 3 Main Cylinder Diameter: 796 mm Press Weight: Approx. 130 ton Stroke & Daylight Stroke: 1,500 mm Daylight: 2,300 mm Table Fixed Table Size: 1,650 mm (R.L) × 2,400 mm (F.B)  ...

This 5-axis DOOSAN PUMA 2000SY was manufactured in 2005, designed for precision in horizontal turning. Ideal for complex machining tasks, it offers robust performance and reliability. Consider the opportunity to buy this DOOSAN PUMA 2000SY horizontal turning machine. Contact us for more information about this machine.

This TORNOS DECO 2000/13 was manufactured in 2000. A robust Swiss type turning machine with a bar passage of 16 mm and maximum spindle power of 9.7 kWh. It includes an IEMCA GENIUS 226/32 loader and a CONVEYORS IND. ASS. TMTPF 1440 conveyor. Equipped with an automatic fire extinguishing system from Kraft & Bauer. Consider the opportunity to buy this TORNOS DECO 2000/13 Swiss type turning machine. Contact us for more information.

General SKU344U850 MakeBee International TypeDeBee 2000 No.2517 Mach.No.2517 Year of construction2002 Pressure Working pressure3100 Bar Main Features Capacity60 Ltr./Hr. Motor7.5 KW Pressure3100 Bar Specified Features - Piston homogeniser Piston homogenisercheck Capacity60 Ltr./h (depends on operating pressure, product viscosity and nozzle type) Number of pistons:2 Inlet1 Outlet¼ Motor7,5 kW With frequence controllercheck MaterialAlumina, Tungsten carbide, Zirconia, Stainless steel 1.4401 (316), Stainless steel 1.4542 (17-4 PH) Information LocationBarneveld Floorspace1,5x0,6 m Total height1,3 m Weight450 kg CEcheckPiston homogenisersDebeeMills > Piston homogenisersBrand > Debee What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspec ...

This 600 Lathes Multiturn 2000 was manufactured in 2004. A robust horizontal turning machine featuring a turning diameter above bed of 400 mm, and a length of 1250 mm. It operates at a spindle speed of 2700 rpm with an 8-position turret. Tailstock taper is Morse 5. If you are looking to get high quality turning capabilities consider the 600 Lathes Multiturn 2000 machine we have for sale. Contact us for more information.

This 4-axis Takisawa EX 2000 MS was manufactured in 2020, featuring a Fanuc 0i-T Plus control system. It offers a max turning diameter of Ø 390 mm and a length of 510.5 mm, with a bar capacity of Ø 65 mm. The machine includes a 12-position driven turret and rapid traverse rates of 30 m/min on the X-axis and 36 m/min on the Z-axis. If you are looking to get high quality turning capabilities consider the Takisawa EX 2000 MS machine we have for sale. Contact us for more information.

This 3-axis KERN CD 480/2000 horizontal turning machine was manufactured in 2010. It features a Heidenhain Manual Plus 620 control, C-axis, driven tools, a 12-fold revolver, and a chip conveyor. With a spindle speed of up to 3000 UpM and a spindle bore of 82 mm, its ideal for precise turning operations. Consider the opportunity to buy this KERN CD 480/2000 horizontal turning machine. Contact us for more information.

This TORNOS DECO 2000/20 was manufactured in 1998. A robust Swiss type turning machine, it features a bar passage of 25.4mm and can handle up to 21 fixed and 15 rotating tools. It includes an IEMCA loader and a conveyor system, enhancing its operational efficiency. Consider the opportunity to buy this TORNOS DECO 2000/20 Swiss type turning machine. Contact us for more information about this machine.

General SKU309X465 MakeHaagen & Rinau LocationBarneveld TypeUnimix Pressure Working pressure3 Bar Vacuum possiblecheck Working pressure jacket4 Bar Main Features MaterialStainless steel Volume2000 Ltr. Motor30 KW Specified Features - Processing vessel Closed stirring vessel3x Capacity3320 l.(2000 l.)/ 2885 l.(1600 l.) /1445 l. (1200 l.) Dished bottomcheck Slope bottomcheck Dished top sidecheck Flat top sidecheck With covercheck ManholeDN400 Top connectionscheck With jacket2x volume 400 l., 165 l. and 95 l. Max. temperature151°C With anchor stirrercheck With paddle stirrercheck With dissolver stirrercheck Motor18kW, 1450 rpm (EX) With homogenisercheck Motor30kW, 2950rpm (EX) MaterialStainless steel 1.4541 (321) Information No.300975/2290 Year of construction1996 Mounted on legscheck With switchgearcheck ( as is) Floorspace7x2,5 m Total height± 3.8m ...

This 5-axis DAEWOO PUMA 2000 SY turn-mill centre was manufactured in 2003. It features a max turning diameter of 330 mm, length of 510 mm, and rapid feeds up to 24,000 mm/min. Includes main and sub-spindle capabilities, both with C-axis, and a 12-station turret with live tooling. Consider the opportunity to buy this DAEWOO PUMA 2000 SY turn-mill centre. Contact us for more information about this machine.

table length: 2000 mm table width: 1000 mm table height: 200 mm bore: 28 mm : 100 x 100 mm material thickness: ca. 24,5 - 27 mm Side panel height: 200 mm work height max.: 850 mm weight: 850 kg Product description: Siegmund retro offer incl. accessories: < < Welding table like 25 years ago, additionally with plasma nitriding and current table feet >> - high-quality steel S355J2+N + plasma nitriding - Side panel holes in diagonal grid - Corners, edges and drill holes chamfered 45° - Construction reinforced with ribs - incl. basic foot equipment (working height 850 mm) Accessories: - 6 x Professional screw clamp, nitrided - 12 x quick-release bolts without groove, double burnished - 8 x universal fence 225 L nitrided - 2 x stop and clamping bracket 175 L nitrided - 2 x stop and clamping angle 500 G nitrided - 1 x accessory set - Eccentric stop Ø 60 with M10 thread nitrided - Hexagon ...

This 3-axis Johnford VMC-2000SHD was manufactured in 2005. It features a large table size of 2200 × 1000 mm and extensive travels: X-axis at 2050 mm, Y-axis at 1100 mm, and Z-axis at 800 mm. With a spindle speed ranging from 10 to 6000 rpm and a tool magazine capacity of 40 tools, this vertical machining centre is ideal for complex machining tasks. Contact us for more information about this machine.

Frame Inner Dimension: 1450 x 1650mm Gas Type: Propane Operating pressure: 7 bar

This 5-axis GEISS FZ 2000 x 1000 was manufactured in 2000. It features a robust CNC milling machine capability with X-axis travel of 2450 mm, Y-axis of 1400 mm, and Z-axis of 800 mm. The milling spindle supports a maximum speed of 45000 rpm with a power of 6 kW. Consider the opportunity to buy this GEISS FZ 2000 x 1000 CNC milling machine. Contact us for more information about this machine.

This Hebrock TOP 2000 PLUS was manufactured in 2015. A used edge banding machine, it features a gluing unit, cutting unit, and combination milling unit. It handles edge material thickness from 0.5 to 3 mm and can manage workpieces from 10 mm to 45 mm in thickness. Ideal for precise edge finishing tasks. Contact us for more information about this machine.

A complete IGM welding system with robot is available. Robot: igm RTI 2000, roller bed: igm RB 300, positioner: igm RP 300, control system: PLC/Kuka K C2. Without workpiece fixtures. Documentation available. An on-site inspection is possible. Expected to be available in May 2026.

This WEBER LCE-2000-S-S1350 was manufactured in 2001. It features a wide-belt sanding machine with a working width of 1350 mm, a sanding unit plus a cleaning brush, and sanding shoes with pressure beam segment control. The cutting speed of the sanding belt is infinitely variable, and it has a 15 kW frequency-controlled drive. Maximum feed speed is 14 m/min. Contact us for more information about this machine.

table length: 2000 mm table width: 1000 mm table height: 150 mm bore: 22 mm weight: 530 kg Equipment: - 4 feet - basic equipment 650 mm - high-quality steel S355J2+N + plasma nitriding - Material thickness approx. 24.5 - 27 mm - Hole Ø 28 mm - Drill holes surface 100x100 mm grid - Corners, edges and drill holes rounded - Side panel height 200 mm - Hole spacing side panel 50 mm - Including scaling on the surface - Construction reinforced by ribs - Grid lines enable precise superstructures The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

This FANUC ROBOSHOT S-2000 i 150B was manufactured in 2012. A pristine electrical injection moulding machine, it has never been used, maintaining zero working hours. It features a 52 mm screw diameter. Consider the opportunity to buy this FANUC ROBOSHOT S-2000 i 150B electrical injection moulding machine. Contact us for more information.

This 6-axis KUKA KR 100-2 HA 2000 was manufactured in 2007. It features a TRUMPF TruDisk 6002 laser with a power range of 120–6000 W and a wavelength of 1030 nm. The robot arm is mounted on a KSL-2000/2700 linear axis, enhancing its operational flexibility. If you are looking to get high-quality welding capabilities, consider the KUKA KR 100-2 HA 2000 machine we have for sale. Contact us for more information about this machine.

table length: 2000 mm table width: 1000 mm table height: 200 mm bore: 28 mm weight: 730 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

This KUKA KR 240-2 2000 robot arm was manufactured in 2009. It features a robust 6-axis system capable of handling a maximum total load of 640 kg, with an arm length of 1100 mm. Ideal for complex automation tasks, this robot arm can be installed on floors or ceilings, enhancing versatility. A great opportunity to buy this KUKA KR 240-2 2000 robot arm. Contact us for further details regarding this robot arm.

Fabricante DAEWOO Modelo PUMA 2000 SY Año 2003 CNC FANUC 18i – T Capacidades Diámetro máx. sobre bancada 600 mm. Diámetro máx. sobre carro 550 mm. Diámetro máx. torneable 330 mm. Longitud máx. torneable 510 mm. Recorridos y avances Recorrido Eje X 250 mm. Recorrido Eje Z 580 mm. Recorrido Eje Y 100 (±50) mm. Recorrido Eje B 580 mm. Avance Rápido eje X 20 m/min. Avance Rápido eje Z 24 m/min. Avance Rápido Y 7,5 m/min Avance Rápido B 20 m/min. Cabezal Eje C INCLUIDO Indexación eje C 0.001 º Paso de barra 76 mm Nariz A2#6 Velocidad 4.500 rpm. Potencia 15 kW Sub-cabezal Eje C INCLUIDO Indexación eje C 0.001º Paso de barra 45 mm Velocidad 6.000 rpm Potencia 7.5 kW Torreta y Herramientas motorizadas Numero de Posiciones Torreta 12 Dimensiones de la Herramienta 25 mm Tiempo de Indexación Torreta 0.1 s Velocidad Herramienta Motorizada 5 ...

This 3-axis Parpas THS125/2000TG was manufactured in 2003. It features a SELCA 3040 control unit, a main spindle with 5000 rpm and 22 kW power, and an electrospindle that reaches up to 28,600 rpm. The machine includes a 24-position tool changer and accessories like a chip conveyor and through-spindle coolant. If you are looking to get high-quality milling capabilities consider the Parpas THS125/2000TG machine we have for sale. Contact us for more information.

This 3-axis horizontal turning machine manufactured in 2020 features a Siemens 840D control and a spindle speed up to 3,600 rpm. It offers a max turning diameter of 600 mm and a length of 2000 mm. Equipped with a chip conveyor, Siemens CELOS control system, and a fume extraction system, its ideal for complex machining tasks. Consider the opportunity to buy this DMG MORI CTX 2000 horizontal turning machine. Contact us for more information about this machine.

This 4-axis CHIRON Mill 2000 High Dynamics was manufactured in 2018. It features a single-spindle head, HSK-A 63 tool holder, and a maximum spindle speed of 20,000 rpm. The machine offers X-axis travel of 2000 mm, Y-axis travel of 630 mm, and Z-axis travel of 550 mm, with rapid traverse speeds of 75 m/min. Consider the opportunity to buy this CHIRON Mill 2000 High Dynamics vertical machining centre. Contact us for more information about this machine.

This 6-axis FANUC R-2000iC 165F robot arm was manufactured in 2019. It features a maximum reach of 2655 mm and can handle wrist weights up to 165 kg. The robots footprint is 771 x 610 mm, and it operates on a 380-575V, 3-phase electrical system. Consider the opportunity to buy this FANUC R-2000iC 165F robot arm. Contact us for more information about this machine.

General SKU340X784 LocationBarneveld MakeBoekels TypeEWK 2000+/WS 1,25 KG CD Klasse X Main Features MaterialStainless steel Specified Features - Miscellaneous transport Capacity4-1500g Information No.VAB-13565-02 Year of construction2002 Floor space1,45x0,9 m Total height1,75 m Weight270 kg Extra Specifications boekels checkweigher: Max belt speed: 0,92m/s max weight: 1500g minimum weight: 4g division value: 0,2g conveyor length 1450 mm conveyor height 800 mm, adjustableMiscellaneous transportBoekelsConveying systems > Miscellaneous transportBrand > Boekels What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

General SKU216M063 LocationBarneveld MakeWinkworth Machinery Ltd Reading TypePV 2000/2 No.16509 Main Features MaterialStainless steel Volume2000 Ltr. Motor0.75 KW Specified Features - Stirring vessel MaterialStainless steel 1.4404 (316L) Closed stirring vessel(1x) Capacity2000 Ltr Vessel sizesdia. 1524x1502mm Dished bottomcheck Flat top sidecheck Manholedia. 500mm Top connections2x dia. 40mm + 2x dia. 50mm Outletdia. 50mm With propellor stirrermake Lightnin Motor0,75 KW, 400 Volt Information Year of construction2001 Mounted on legscheck Floorspace1,7x1,7 M Total height3,1 MStirring vesselsWinkworthStirring vessels > Stirring vesselsBrand > Winkworth What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The ...

General SKU279M286 MakeACOMETI LocationBarneveld Main Features MaterialStainless steel Volume2000 Ltr. Motor3.6 KW Specified Features - Stirring vessel MaterialStainless steel Closed stirring vessel(1x) Capacity2000 Ltr Vessel sizesdia. 1400x1200mm Conical bottomcheck Dished top sidecheck Manholedia. 300mm Top connections9x Outlet80mm With jacket(bottom) With paddle stirrercheck Motor3,6 KW, 220/380 Volt (Ex) Information Floorspace1,6x1,6 M Total height3,5 M Weight1300 KG ATEX compatiblecheckStirring vesselsAcometiStirring vessels > Stirring vesselsBrand > Acometi What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

General SKU382X962 MakePharmatech LocationBarneveld Type2000 L. Main Features MaterialStainless steel Volume2000 Ltr. Motor7.5 KW Specified Features - Tumbler mixer Double cone tumbler mixercheck Capacity924 kg Diameter1562 mm Length/Depth1884 mm Cylindrical length465 mm Conical length880 mm and 539 mm InletDia. 560 mm OutletDia. 250 mm With motor7,5 kW, 400 volt, 1360 rpm Speed mixervariable – range 2 - 18 rpm With safety gatescheck safety laser scanner MaterialStainless steel 1.4401 (316) Information No.E10866 Year of construction2017 With switchgearcheck (as is) Floorspace3,50x1,86 m Total height3,41 m Weight1000 kg Extra SpecificationsThis tumble mixer was installed in its original configuration with multiple accessories. - Pharmatech floor scale, SKU: 382X960 - Pharmatech flexisieve 350 0.1m², SKU 382X961 (SOLD) - Pharmatech Hoist, SKU 382X963 Tumble ...

Heckert ZFWVG 250 x 2000 Thread Milling and Spline Hobbing Machine. Max. workpiece diameter 250 mm Workpiece diameter over bed 500 mm Center height over bed 260 mm Threading/hobbing length 2000 mm Min/Max. module 2/18 Workpiece spindle bore 102 mm Bore of the collets 100 mm Tailstock quill stroke 100 mm Speed 45 – 560 rpm Lead of leadscrew 1,2 '' links / left mm Workpiece turning speeds 0,0032-2,65 U/min Rolling feed 0,027-5,66 mm/WU Longitudinal hob feeds 0,3-198 mm/min Main drive 4 kW Feed motor 25 NM Coolant pump 0,09 kW Lubrication pump 0,37 kW Total power requirement 9,5 kW Dimensions 3700x2400x1600 mm Total weight 5200 kg Accessories; -heavy duty head -standard head -steady rest -flange -change gears full set

CNC Machining Center Hedelius C60P-2000 Magnum Control: Heidenhain iTNC 530 Year of Make: 2009 Travels: X-axis 2,000 mm Y-axis 620 mm Z-axis 520 mm Clamping area 2,500 x 600 mm Mount: SK 40 Tool Magazine: 56 – Tray Spindle speed: 8,000 rpm Accessories: - Chip conveyor AME KB 448 - Paper belt filter AME PS 120 - LTA suction - Machine hood

CNC lathe DMG MORI NLX 2000 SY/500 With DMG MORI M730 UM MAPPS CELOS CONTROLLER Year of Make: 2016 Max. workpiece diameter: 366 mm Max. workpiece length: 510 mm Travel in X: 260 mm Travel in Z: 590 mm Travel in Y: +- 50 mm Spindle bore: 65 mm Main spindle speed range: 4000 rpm Speed range sub-spindle: 6000 rpm Speed range of driven tools : 10000 rpm With the following accessories: Workroom door with interior lighting 20-fold turret with 20 driven stations C Axis , Y Axis Touch Probe ( Marposs ) Sub-spindle, parts catcher Tool presetter manual ( HS ) Collet Chuck Hydraulic with Foot Pedal (HS) Collet Chuck Hydraulic with Foot Pedal (GS) Bar Feeder LNS Move S2 30 tool holders Various powered tools Direct displacement measuring system X, Y, Z axis Signal lamp 4 colours Chip conveyor Coolant Setup Operating Instructions

Two identical thermoforming machines DIXIE-UNION DV 2000 are available. Supply voltage: 380V, frequency: 50Hz, rated current: 20A, version with red CEE three-phase plug (3~). Machine 1 was still in operation until 2025. Machine 2 has not been in use for a longer period and is not complete, as relays were removed for spare parts. An on-site inspection is possible, not under power.

General SKU261S241 MakeSpiromatic Year of constructionunknown manufacturer plate is missing Mounted on framecheck Main Features MaterialStainless steel Volume2000 Ltr. Specified Features - Silo Silocheck Closedcheck Capacityca. 2000 ltr Sizesdia. 1200x2000mm Diameter1200m Cylindrical height1200 Conical height800 Conical bottomcheck Flat topcheck Manhole400x300mm Inletca. 200mm Top connections(3x) ca. 200mm Outlet with vibro bottomcheck Outlet with valvebutterfly valve (pneumatic) Outlet300mm MaterialStainless steel Information LocationBarneveld Floorspace1,5x1,4 M Total height3,4 M Weight500 KgSilosSpiromaticTanks > SilosBrand > Spiromatic What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Nether ...

Standard equipment: - Sturdy C-frame - Safety light barriers - Coordinate guidance with integrated Linear magazine - 2 clamping claws - Automatic tool changer - Automatic repositioning - Tool length compensation - Forming option - Mono tool holder 360 rotation for all tools - Programmable hold-down device - Multi-tool drive - Punched slug extraction - Brush tables - Parts chute 200 x 200 mm Part sorting in 2 containers - NC-controlled, digital, maintenance-free three-phase AC drives - Network interface RJ34 - 3.5 Floppy Disk Station - Graphics programming TOPS 2000 -