129,451 used machines on RESALE, but how to find them? Machine Search
Centrifugal pump FRISTAM Capacity: 2,500 l/h Flow rate: 2,500 l/h Operating pressure test 2.3 bar Motor: 2.2 kW Connections: suction side and discharge side: DN 80 - With chassis mobile with 2 swivel and 2 fixed castors - With cable and CE plug 16A Dimensions: Length: 850 mm Width: 500 mm Height: 1000 mm Note: Pump 100% tested, with function guarantee On request, infinitely variable with frequency converter for an additional cost.
A Ueda Shiko Kikai (Seiko) flatbed die-cutting machine from the 1980s is available. Throughput capacity: approx. 3600 sheets/h, max. sheet length: 1370mm, max. sheet width: 970mm, min. sheet format X/Y: 530mm/300mm, machine dimensions X/Y/Z: approx. 8150mm/2350mm/2050mm, weight: approx. 20000kg. An on-site inspection is possible.
Injection moulding machine Krauss Maffei KM 200-1400 C2 BJ 2000
A semi-automatic tube filling and sealing machine Norden Machinery with chute and vacuum tipper is available. Filling volume range: 1ml-300ml, container volume: 90l, filling capacity: approx. 140tubes/min, machine dimensions X/Y/Z: approx. 2500mm/1400mm/2400mm, weight: approx. 3300kg. Documentation available. An on-site inspection is possible.
UNDERWATER PELLETIZER, for rigid and soft PP max MFI : 30 (and more), electrical heater max 14,6 kW, n.2 thermo regulating zones, A pressure transducer and a melt temperature transducer are mounted on the purge valve. The purge valve is controlled by a hydraulic cylinder connected to a hydraulic power unit with a 2.2 kW motor., Steel die with brazed tungsten carbide plates. A conveyor cone for the molten polymer is installed inside., stainless steel granulation chamber, Impeller shaft with 11 kW 2-pole drive motor (3000 rpm nominal, 4000 rpm max) controlled by an inverter with rpm variation and speed readout on the panel. The shaft output side has special seals and a labyrinth and safety water drainage to protect the motor bearings. The impeller motor is integral with a slide sliding on rolling guides, operated, via a recirculating ball screw, by a manual handwheel equipped with a positi ...
Work table AT 1400 with beech hob Beech wood worktop with gallery at the back Storage shelf at the bottom Stainless steel Approx. dimensions: 1425 x 800 x 860 mm, WxDxH Used device cleaned Plate sanded & re-oiled Quality from a specialist company! Benefit from over 35 years of experience!
Screw Diameter: 140 mm // Throughput: 900 kg/h
Board machine Type: Tronic 140/90-22 Manufacturer: OMAG Year: 1996 The board machine built in 1996, has been operated continuously since it was commissioned in 1997. For sale is not only the block machine itself but also the entire production line, allowing full use of the system after purchase. Several components of the mixing plant (e.g. core and face mix mixers), the bucket conveyor, wet side, transfer platform, dry side, and package buffer were renewed in 2009. The block machine remained in operation until the end of 2024 and can be inspected in fully functional condition. MACHINE DATA Block forming machine Board machine manufactured by OMAG, type TRONIC 140/90-22, year of manufacture 1996 Production of core and face mix Control system: Simatic S5 with visualization by Frima Board size: 1,400 × 1,000 mm Cross cleaning Quick mould clamping, pneumatic Sheet pulling dev ...
4-axis machining centre with 8-fold tool changer for aluminium or PVC profiles Max. machining length: 3,100 mm Y-axis travel: 850 mm Travel Z-axis: 650 mm Swivel angle A-axis: 0° - 180° Max. speed 21,000 rpm Weight: approx. 3,000 kg Windows 7 Operating System Minimum Quantity Spraying Tensioner detection and automatic displacement 6 pneumatic material clamps 2 material stops Loading is included in the price
Key data: 150 KW, 220 kVA, 400 V
Sokratherm Gas-CHP GG 140S oE Gas electricity and heat generator from 2010, with approx. 60,000 operating hours, with control and silencer. 1 available 140 KWel x 1,500 rpm, 400 V/50 Hz. AC Generator: MarelliGenerators MJB 250 LA4, 220 KVA Manufacturer: Sokratherm Model: GG 140S oE Type: Gas CHP Serial Number: F103064 Engine: MAN E2876 E312 Electrical power [KWel]: 140 Thermal power [KWth]: 216 Gas capacity [KWgas]: 392 Year of Make: 2010 Operating hours: approx. 60,000 Weight unit [kg]: 2,850 Dimensions LxWxH [m]: 3.00 x 0.9 x 2.4 AC Generator Marelli MJB 250 LA4 Manufacturer: MarelliGenerators Model: MJB 250 LA4 Type: AC Synchronous Generator Serial Number: MJB2572GT68MO Power [KVA]: 220 Voltage [V]: 400 Frequency [Hz]: 50 Current [A]: 317 Speed [1/min]: 1,500 Year of Make: 2010
OVERHAULED - Size: 1.400 x 3.000 mm - With Electrical motor, Cardan shaft and Spring elements.
Magnet L x W x H: 1.526 x 750 x 305mm. - Belt: 800mm. - AA.: Ca. 2.450mm. - Weight: 1.800 KG.
Power: 14 kW - Amperage: 63,58 A - Voltage: 220V. DC - 100% ED Magnet L x W: (1.400 + 2 x 420=) 2.240 x 1.360 mm - Conveyor belt: 1.400 mm - AA.: Ca. 2.900 mm - With Transformer rectifier of 380V. Primary
ICMA SAN GIORGIO TWIN SCREW EXTRUSION LINE, used for PE PP, Forced feeding hopper with frame, Extruder with segmented screws 2x140 mm. 32 LD, 200 Kw drive, n.1 vacuum degassing pump, hydraulic screenchanger, Water ring pelletizer (year 2016), drying centrifuge in stainless steel, Constructed in 1990, Offered AS IS WHERE IS, conditions: used
ICMA SAN GIORGIO TWIN SCREW EXTRUDER CO-ROTATING, used for elastomers TPE TPU SBS,.., Extruder with co-rotating segmented screws 2 x 140 mm 36 L/D, Screws speed 178 rpm, Reinforced gearbox, Siemens 430 kW drive, degassing pump, semi-automatic hydraulic screenchanger, hydraulic pack, Dry pelletizing unit, Electric panel overhauled in 2015, added touch control, Constructed in 1997, CE compliance declaration, electric drawings.
max. wheel diameter: 1400 mm gear width: 400 mm max. module: 25 min. module: 1 total power requirement: - kW weight of the machine ca.: 7,0 t dimensions of the machine ca.: 3,0 x 1,2 x 3,2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 873x470x336 mm Weight: 111 kg Total power requirement: 4 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 980x860x1380 mm Weight: 165 kg Total power requirement: 0,75 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 3000x3000x1800 mm Weight: 1000 kg Total power requirement: 10 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
turning diameter over bed: 1450 mm turning diameter over slide rest: 1000 mm turning length: 8000 mm spindle bore: 160 mm turning speeds: 2,8-560 U/min faceplate: 1400 mm 3-jaw chuck: mm bed width: 850 mm turning diameter in the gap: 1800 mm length of gap: 600 mm steady: 1070 mm steady: 1070 mm digital readout: Rapid travel: chip conveyor: kW total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Multifix steel holder with inserts The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contac ...
Sacot CA plank stacker. SCA. SAWMILL 1400 A professional stacker designed for automatic stacking of boards into even, stable and repeatable stacks. An ideal solution for sawmills and wood processing plants, significantly increasing efficiency and comfort of work. TECHNICAL PARAMETERS Stacking Material Length: 770-1400mm Stacking width: 1200 mm Stacking height: 1250 mm Machine dimensions: 4600 × 3700 × 2600 mm (H) Feeding/Receiving: Roller Receiving Table Structure: Steel, Industrial, Heavy Duty Control: Electric + Pneumatic The stacker is perfect for: sawmills, wood processing plants, production lines, production of short and medium elementsEXPANSION OPTIONS (optional): a complete technological line, including: Weinig Hydromat 23c planer 60m/min SACOT Formatizer SACOT stacker
greates pass round over bed: 540 mm swing diameter over face slide: 370 mm centre distance: 3000 mm centre height: 270 mm turning dia. in gap: 815 mm bed width: 344 mm spindle bore: 88 mm spindle diameter in front bearing: 133 mm spindle taper: 11 D1 Camlock turning speed range: 18-1400 U/min turning speeds: 16 3-jaw chuck: Röhm Ø 315 longitudinal feeds:: 0,06-1,0 mm face feeds: 0,03-0,5 mm metric threading: 0,4-14 mm inch threading: 2-72 G/1 thread - module: 0,3-3,5 mm thread - DP: 8-60 Pitch tailstock quill diameter: 75 mm quill stroke: 230 mm taper of tail spindle: MK 5 slide valve travel: 280 mm upper head travel: 150 mm Overall size: ca. 4700 x 1100 x 1400 mm weight: ca. 3200 kg power capacity: 9,4 kW Accessories: 3-axis digital display Fagor Röhm wedge bar chuck Ø 315 mm Multifix steel holder size C incl. 6 interchangeable cassettes Rotating center point Turning chuck guard Rea ...
1 of used trayshrinkpacker, make Kisters (KHS) type 140/60, new 1989, operating side left. Fitted with Siemens S7 controls / HMI and Bosch Rexroth servo drive MI-technology in 2012. Nordson hot-melt unit Originally supplied to pack food cans as 4x3 and 6x4 on tray plus film. Last used for food cans as 6x2 and 4x3 on tray + film. Size-adjustable via spindles and servos. Maximum capacity 60 trays/minute (depending on product).
1 of used trayshrinkpacker, make Kisters (KHS) type 140/60, new 1989, operating side left. Fitted with Siemens S7 controls / HMI and Bosch Rexroth servo drive MI-technology in 2012. Nordson hot-melt unit Originally supplied to pack food cans as 4x3 and 6x4 on tray plus film. Last used for food cans as 6x2 and 4x3 on tray + film. Size-adjustable via spindles and servos. Maximum capacity 60 trays/minute (depending on product).
Inv. Num. : 8914 Type: MA 1400 - DX 100 Producer: Yaskawa Created: 2012 Parameters: Maximum arm reach: 1434 mm Number of axles: 6 pieces Maximum load capacity: 3 kg Machine weight: 130 kg
This EUMACH SUMO 1400 Vertical Machining center was manufactured in the year 2004. It is equipped with a HEIDENHAIN 426 control unit and has 3 axis. The machine has a spindle speed of 15000 rpm, is good condition and well maintained.
This 4-axis WAGNER VMC 1400 was manufactured in 2007. It features a spindle power of 28 kW, maximum spindle torque of 230 Nm, and a spindle speed up to 4000 rpm. It includes a 4th axis for machining workpieces up to 1100 mm. Ideal for complex machining tasks. Contact us for more information about this machine.
Transnorm conveyor belt GF 14000-600-500 RA2463 Technical data: Conveyor length (NL): 14000 mm frame width (NB): 600 mm, 700 mm with motor belt width (GuB): 500 mm Overall height (BH): 80 mm, 430 mm with motor Supporting feet: optionally available Conveying speed (v m/s): 0,5 Drive: SEW gear motor, R40 DT80N4 Electrical data: 50Hz V380-500, kW 0,75 S1 Drive drum: Ø = 81 mm Belt return roller 1: Ø = 81 mm Belt return roller 2: Ø = 40 mm Optionally available: Supports Side guide on one side and on both sides Frequency converter for stepless speed change Adjust length (longer/shorter) Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg, Germany Features: condition: good (used) Conveying length in mm: 14000 Nominal / outside width in mm: 600 Belt width in mm: 500 Driven: YES Engine type: SEW Eurodrive Zentralantrieb mit Spannstation KW: 0,75/S1 Conveyor spe ...
This 3-axis MAHR MarSurf CD 140 CMM machine was manufactured in 2022. It features a contour probe system with a resolution of up to 6 nm and a traversing length from 0.1 mm to 140 mm. The machine supports a workpiece weight of up to 90 kg and offers adjustable measuring forces from 4 mN to 30 mN. If you are looking to get high-quality contour measuring capabilities, consider the MAHR MarSurf CD 140 machine we have for sale. Contact us for more information.
General SKU268N300 MakeHeraeus Hanau TypeRVT 500 No.7805013 Year of construction1978 Mounted on framecheck Main Features MaterialAluminium Volume140 Ltr. Max.temp.180 °C Specified Features - Drying oven Vacuum drying ovencheck Max. temperature180 °C Number of compartments:1 Capacity140 Ltr Internal diameter485mm Internal depth750mm Electric heatingcheck Electric capacity2 kW 220 Volt Number of doors:1 With trayscheck MaterialAluminium Information LocationBarneveld With switchcheck Floorspace1,0x0,7 M Total height1,6 M Weight150 KGDrying ovensHeraeus HanauDryers > Drying ovensBrand > Heraeus Hanau What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for man ...
This Krauss Maffei KM 200 CX 1400 MC5 was manufactured in 2008. It features a clamping force of 200 tons, expandable to 300 tons, and a screw diameter of 60 mm. The machine includes a hydraulic ejector, side air valve, robot interface, and a 4-zone mold temperature control system. If you are looking to get high-quality injection molding capabilities, consider the Krauss Maffei KM 200 CX 1400 MC5 machine we have for sale. Contact us for more information.
This 6-axis ABB IRB 140 M2000 robot arm was manufactured in 2005. It is designed for flexible use in manufacturing facilities, featuring an open structure that easily adapts and communicates with external systems. Weighing 98kg, it operates quietly with noise emissions under 70 dB(A). Consider the opportunity to buy this ABB IRB 140 M2000 robot arm. Contact us for more information about this machine.
Only for Export ! Fuji PI1400HS ( ECRM VRL36HS ), A3 HighSpeed Film Imagesetter, HQ-RIP with PC and second Take up Cassette
An autoclave Stock DFT including a Jumag steam system for the food industry is available. Batch trolley capacity: 2, process method: steam-water spraying, application: sterilization/pasteurization, gross volume: approx. 1550l, steam system: Jumag DG560, steam output: approx. 560kg/h. Including 6 batch trolleys. Documentation available. An on-site inspection is possible.
General SKUR0159 LocationBarneveld CEcheck MakePink GmbH Thermosysteme Pressure Vacuum possiblecheck Working pressure jacket3 Bar Main Features MaterialHastelloy Volume250 Ltr. Surface2.7 m2 Specified Features - Tray dryer Tray dryercheck Stainless steel housingcheck Stainless steel trayscheck Heating surface2,7 m² Drying chamber sizes670x670x140mm (4x) With jacketcheck Max. temperature115 degr. C Number of trays4 Tray sizes670x670mm Distance between the trays140mm Max. temperature115 degr.C With containers4x Container sizes650x650x40mm With 1 doorcheck MaterialStainless steel 2.4602 (Hastelloy C-22) Information TypeVSD-EX 650-650-140-4 Machine number2005 4783 Year of construction2005 With switchgearcheck Floorspace1,6x1,2 M Total height2,3 M Weight1400 KgTray dryersPink WertheimDryers > Tray dryersBrand > Pink Wertheim What you can expect from Foeth: ...
Two walk-in climate chambers including Wolf burner are available. Heating capacity: 105kW, heating medium: oil/gas, max. oil throughput: 14.9kg/h, air volume flow: 2.78m³/h, max. external delivery pressure: 400Pa, control: PLC. Documentation available. An on-site inspection is possible.
used
From a current disposal, we offer you an IVECO Eurocargo truck with box body from Humbaur. Year of Make: 2019 Registration date: 24.04.2019 Condition: Satisfactory KM: 303.000 Asking price: 22.500,00 VHB Equipment / accessories / other information: Asset Manager: M. Vorkötter Phone: 0202-25727-3152 Mail: m.vorkoetterakf.de We will be happy to provide you with details upon request. Location: 67240 Bobenheim-Roxheim The sale is without warranty Subject to prior sale
BILLION Hercule 140 T Injection Moulding Machine Injection group: H470 Clamping force: 140 T Screw diameter: 40 mm Injectable volume: 220 cm3 Injection pressure: 2100 bar L/D Ratio: 23.5 Distance between columns: 515 x 515 mm Distance between columns: 735 x 735 mm Min/max mold thickness: 240-480 mm Opening stroke: 500 mm Engine power: 18.5 KW Heating power: 9.60 KW Dimensions: 5.10 x 1.80 x 2.25 m Weight: 6.8 T
x-travel: 2400 mm y-travel: 2000 mm z-travel: 1450 mm table surface area: 5000 x 1400 mm spindle taper: SK 50 Control: Fidia C1 The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Lokotrack LT140 Year of manufacture 1996 Crusher inlet 1400 x 1070 mm Converted to electric drive 200kW Machine in operational condition from a limestone quarry/cement plant 115 tons 4 Transports
sheet width: 2050 mm plate thickness: 4,5 mm pre-bending: 4,0 mm min. dia.: 210 mm roll diameter: 140 mm weight of the machine ca.: 1530 kg dimensions of the machine ca.: 3220x1200x900 mm Standard features: - Central rollers via electric motor, planetary reduction gear and Gear drive driven - Swivel top roller - Main engine with brake device - Conical bending device - Mobile controller and foot pedal - CE mark / Declaration of Conformity Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
faceplate diameter: 10000 mm swing diameter: 14000 mm turning height: 8000 mm Control: Siemens Sinumerik 840 D workpiece weight max.: 500 t faceplate turning speed range: 0,2 - 35 U/min drive motor: 300 kW ram head dimension: 600 x 600 mm max. ram stroke: 4000 mm milling drive: 100 kW hob turning speeds: 3000 U/min rapid traverse x + z axis: 10 m/min total power requirement: - kW weight of the machine ca.: 350 t Machine has never been used and is still original, seaworthy packed and stored. equipped with: - CNC control Siemens Sinumerik 840 D - Hydrostatic axes - Hydrostatic table - Milling device - Hirth couplings for tool holder Acessories: • VERTICAL HEAD ISO50 BIG PLUS AD 8T5060164 • VERTICAL HEAD ISO50 BIG PLUS AD 6000RPM 8T5060165 • HORIZZONTAL HEAD ISO50 BIG PLUS 8T5060163 • UNIVERSAL HEAD TU-50- ISO50 AD BIG PLUS 8T5060171 • HEAD DANDREA UT-8-800-S 8T5060166 • TOOL HO ...
: 15000 kg height: 790 - 1150 mm width: 1400 mm : ja : 790 - 1350 mm : 120 x 1400 mm Support stand, assembly stand, steel stand, welding table, assembly table, steel trestle, work trestle - Our jack stands are characterized by their stable construction, high load-stable stability and indestructible service life. - powder-coated in RAL 5010 gentian blue - CE marking - Transport on request The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
faceplate diameter: 1400 mm Thickness: 200 mm : 650 total power requirement: . kW weight of the machine ca.: 1000 kg dimensions of the machine ca.: . m 340 rpm Bolt circle: 330 mm Fit: 285 mm Jaw width: 55 mm Thickness: 170 mm Opening: 145 mm The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG ...
An automatic Munder blow-off system for cleaning cylindrical air filter cartridges is available. Compressed air supply: 6bar-8bar, quality: 5, nozzle pressure: 6bar, volumetric flow rate: 190m³/h, vacuum: 20kPa, max. filter height: 1400mm, max. filter diameter: 540mm. Documentation available. An on-site inspection is possible. Expected to be available June 2026.
spindle diameter: 140 mm x-travel: 6000 mm y-travel: 2400 mm w-axis: . mm ram: horizontal adjustment: . mm ram: diameter: 300 mm spindle taper ISO: 50 turning speeds: 3,15-800 U/min angular milling head: rotary table:: 2250x2250 mm table travel longitudinal: 1600 mm rotary table:: 2250x2250 mm table travel longitudinal: 1600 mm Optional worktop Optional: 2 Collet boring tables The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We loo ...
General SKU279X367 MakeSondex TypeSonspy 1400 No.SP10096 Year of construction2014 Mounted on framecheck Pressure Working pressure shell16 Bar Main Features Shell (Material)Stainless steel Tube (Material)Stainless steel Surface18.87 m2 Specified Features - Shell and tube heat exchanger Heat exchangercheck Horizontalcheck Heating surface18,87 m² Max. temperature200 °C Shell diameter1400 mm Max. temperature200 °C MaterialStainless steel 1.4404 (316L) With jacketcheck General LocationBarneveld Floorspace2,20x2,40 m Total height1,60 m Weight5000 kg CEcheck Extra SpecificationsSpiral heat exchangerShell and tube heat exchangersSondexHeat exchangers > Shell and tube heat exchangersBrand > Sondex What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are wel ...
Work table AT 1400 with stainless steel top Work table Baker's table Stainless steel worktop with gallery at the back Bottom shelf Stainless steel version with 2 doors Approx. dimensions: 1400 x 800 x 850 mm, WxDxH Used device cleaned
maximum number of results exceeded
please refine your search
