131,078 used machines on RESALE, but how to find them? Machine Search
Alfa Laval PAPX 307 SGD -11G Purifier Alfa laval PAPX 307 purifier Bowl - stainless steel Hydraulic capacity 8.000l/h Motor 7.5 kW
Knapp roller conveyor accumulation 24V 2700-1170-1110 RA2377 Make: Knapp Running direction: both directions Roller width (RB): 1110 mm Nominal/outer width (NB): 1170 mm Length: 2700 mm Roller diameter: 50 mm Roller distance: 60 mm Stowage area length: 540 mm Motor Roller conveyors: Interroll EC300 24V Height frame: 90 mm Conveyor speed: freely adjustable up to 1,25m/s with Interroll EC300 Motor Scope of delivery: without supports, Light barrier included Optionally available: Supports Side guides Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: condition: very good (used) scope of delivery: without supports and side guides Driven: YES nominal voltage: 24V Conveyor speed m / s: bis 1,25m/s Engine type: Interroll EC 300 Roll division in mm: 60 Jam detection: Lichtschranke Conveying length in mm: 2700 Nominal / outside width in mm: 1170 Stowage ...
Berghof High Pressure Reactor Type BR-1000 composed of: Stainless steel reactor BR-1000 with lid (6 inlets with rupture disc, valve, temperature and pressure sensors for control and recording) and 2 Teflon liners, each 1 liter reaction volume BHM-1000 Heating jacket Temperature controller BTC-1000 with interface to Windows software for programming, visualization and data recording Large number of reusable Teflon seals Hardware The device is used but fully functional
Cast iron bed Length: 3650 mm Width: 1370 mm Thickness: 150 mm 11 T-slots - dimensions 32 x 18 mm Slots spacing: 125 mm Assembly in 2 parts Dimensions of each part: L 1820 mm x W 1370 mm x H 150 mm Total height on base 875 mm Weight: approx 4 T
Knapp roller conveyor accumulation 24V 2700-1110-1050 RA2378 Make: Knapp Running direction: both directions Roller width (RB): 1050 mm Nominal/outer width (NB): 1110 mm Length: 2700 mm Roller diameter: 50 mm Roller distance: 60 mm Stowage area length: 540 mm Motor Roller conveyors: Interroll EC300 24V Height frame: 90 mm Conveyor speed: freely adjustable up to 1,25m/s with Interroll EC300 Motor Scope of delivery: without supports, Light barrier included Optionally available: Supports Side guides Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: condition: very good (used) scope of delivery: without supports and side guides Driven: YES nominal voltage: 24V Conveyor speed m / s: bis 1,25m/s Engine type: Interroll EC 300 Roll division in mm: 60 Jam detection: Lichtschranke Conveying length in mm: 2700 Roll width in mm: 1050 Nominal / outside wi ...
Technical data: Type : Casting resin transformer Finish : Dry Make : ABB Year of construction : 2000 Condition : Used Rated power : 1250 KVA Medium voltage : 10 KV Low voltage : 400 V Groupset : Dyn 5 Frequency : 50 Hz Cooling Type :AN Gross vehicle weight : 3090 kg Nationwide delivery included.
3 boxes x hotmelt HM-180 (5kg bag) remainder Art.Nr. 995.18.02 (L985) 75€ for 3 cartons
Impressions=0 m, Condition= Very Good , Availability= 2026-05-01, Max. sheet size: 1100 x 1050mm Min. sheet size: 350 x 350mm Top sheet: 130 – 450gsm Bottom sheet: 250 gsm to 10mm Automatic top sheet rear edge sheet feeder Automatic substrate rear edge sheet feeder Glue system Stacker unit PLC control system 400.000 sheets produced only !
used
A renovated extrusion recycling brand EREMA INTAREMA 1310 TVEplus for processing polyethylene (PE) and polypropylene (PP), polystyrene (PS), with laser filter and screen changer, degassing for processing printed films. Output up to 850 kg/h, electrics 240/400 volts, 50 hertz, immediately available. Financing possible without personal liability. Auch + Technik e. Kfm. D-73728 Esslingen Official agent for EREMA GmbH A-Ansfelden Phone +0049 1577 5329827
Hacker Zerbrik Motor 30KW Wavelength 1m Hydraulic Moving Floor Weight 3t Year of construction 2009 Dimensions: 1900x2600x1800 mm (LxWxH) Very suitable for pallets due to the long shaft, nails are no problem for the machine. For 25 years, we have specialized in the sale of woodworking machinery. Each of our machines is extensively tested before sale to ensure the highest quality and reliability. The satisfaction of our customers is our top priority. You are welcome to visit and test the machines in advance so that you can personally convince yourself of their flawless function and quality. In addition, delivery can be organized by us on request. For further information or questions, please do not hesitate to contact us at any time by phone or message.
used
A renovated extrusion recycling brand EREMA INTAREMA 1310 TVEplus for processing polyethylene (PE) and polypropylene (PP), polystyrene (PS), with laser filter and screen changer, degassing for processing printed films. Output up to 850 kg/h, electrics 240/400 volts, 50 hertz, immediately available. Financing possible without personal liability. Auch + Technik e. Kfm. D-73728 Esslingen Official agent for EREMA GmbH A-Ansfelden Phone +0049 1577 5329827
Key data: 190 mm
Stock No: 3764 CNC LATHE Manufacturer: Mori Seiki, Type: ZT 1000Y Machine NO.: ZT101CB0056, Year of manufacture: 2003 Specifications: Max. circumferential diameter 190 mm dia. Max. turn. About BED 250 mm DIA. Main motor power 22/18.5 kw Main spindle speed range 6000 rpm Hole through drawing tube 46 mm dia. C axles 0.001 Y axis 40+/- mm Z Aksen Rapid Traverse 1/2 - 24 m/min Tool turret 1 with 16 stations Motor power driven tools 5.5 / 3.7 / 2.2 kW Kw Tool turret 2 with 16 stations Powered tools. 6000 rpm Sub-spindle Sub-spindle speeds 6000 rpm Control MSX-501 Fabr. Power on 15088 hours Operating hours spindle 5080 hours Controlled in 5+2 axes Accessories: Load and Unload device Hydr. Chuck main spindle 169 mm dia Hydr. Chuck Subspindle 169 mm dia Tool setter Weight: 5000 kg
Topos spiral mixer SP 160, 160 kg dough, two kettles, year of construction 2014, good condition
Knapp roller conveyor accumulation 1100-510-450 RA2382 Make: Knapp Running direction: both directions Roller width (RB): 450 mm Nominal/outer width (NB): 540 mm Length: 1100 mm Roller diameter: 50 mm Roller distance: 60 mm Stowage area length: 540 mm Height frame: 90 mm Motor Roller conveyors: Interroll EC300 24V Conveyor speed: freely adjustable up to 1,25m/s with Interroll EC300 Motor Scope of delivery: without supports, Light barrier included Optionally available: Supports Side guides Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: condition: very good (used) scope of delivery: without supports and side guides Driven: YES Roll width in mm: 450 Nominal / outside width in mm: 510 Conveying length in mm: 1100 nominal voltage: 24V Engine type: Interroll EC 300 Roll division in mm: 60 Conveyor speed m / s: frei einstellbar bis 1,25m/s Stowag ...
Knapp roller conveyor accumulation 12720-510-450 RA2379 Make: Knapp Running direction: both directions Roller width (RB): 450 mm Nominal/outer width (NB): 540 mm Length: 12720 mm in 7 Elements. Roller diameter: 50 mm Roller distance: 60 mm Stowage area length: 540 mm Roller conveyors Drive: 30mm Belt Height frame: 90 mm Conveyor speed: 0,5m/s Scope of delivery: without supports, Light barrier included Optionally available: Supports Side guides Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: condition: very good (used) scope of delivery: without supports and side guides Driven: YES Roll width in mm: 450 Nominal / outside width in mm: 510 Conveyor speed m / s: 0,5 Roll division in mm: 60 Jam detection: Lichtschranke Construction year: 2022 Engine type: SEW Getriebemotor Conveying length in mm: 12720 Stowage spaces: 23 For individual, expert ...
Used Hydr. Adira press brake with CNC controlled crowning WILA Scope of delivery: without tools LazerSafe Security System/CE Foot pedal Two front support arms 500mm, movable Table crowning: WILA motorized Special features: patented HEXA-C frame: low-torsion and therefore very accurate Hydraulics in semi-hybrid equipment very energy-saving because the engine is in the Idle only runs at 5Hz The bounce during start-up and descent is controlled by two high-precision servo valves Two linear encoders ensure accurate positioning of the press beam Adjustable guide of the press beam made of self-lubricating material Electrics and hydraulics with surge protection X&R axis run on backlash-free ball screws driven by servo motors 2 manual stop fingers Z axis Machine rear secured with light barrier AD 60 CNC control type Adcontrol 2 D Machine is repaired, check ...
grinding diameter: 250,350,450 mm grinding length: 1000 mm centre height: 125,175,225 mm grinding wheel diameter: 400 mm grinding wheel width: 50 mm bore: 127 mm : MK5 work piece spindle speed: 20-400 U/min workpiece spindle - bore: mm grinding head swivelling: 360 ° grinding spindle head - swivable: 180 + - ° grinding spindle speed: 1500,1700,2200 U/min : 0,001-0,030 mm/Ø : 0-0,95 mm/Ø : ±8 ° longitudinal feed of the table: 1300 mm table speeds: 0,02-6 m/min : 130 kg : 130 inkl. Spannugkg kg : mm grinding depth: mm : 70 mm total power requirement: 6,5 kW weight of the machine ca.: 2,5 t dimensions of the machine ca.: 4,2 x 2,0 m Ready for delivery, with 12 month warranty in germany and neighbouring countries! Geometrically overhauled and repainted with new electrics. In KELLENBERGER quality! -Digital display in 2 axes. Resolution x-axis 0.5my -Modern workpiece headstock with cone ...
Offer 25086 Specifications: - Flat steel shears - Flat steel - 400 x 120 mm - or: 300 x 22 mm - Profile steel shears - L- and T-irons at 90° 150 x 12 mm - Square steel / round steel 40 / 40 mm - Notches - With square clinker for sheet metal up to approx. 13 mm - Latch depth approx. 70 mm - Latch width approx. 52 mm - Hole punch - Punching force approx. 100 t - Projection 510 mm - Stroke approx. 10 to 50 mm - Perforates in steel up to Ø 31 in 25 mm - E. contact stop - div. 10 pcs. punches + dies - Drive 400 V / 5.5 kW - Space required: W 1100 x H 2000 x D 1700 mm - Weight approx. 2100 kg
Technical data of the pallet rack stand: Shelving system: SSI Schaefer Type: K The scope of delivery includes: 01x Pallet rack stand, used Material colour: sendzimir galvanised Profile dimensions: 90 x 75 x 2.5 mm Incl. cross and diagonal struts, Footplates The stands are pre-assembled (screwed truss) Frame height: 2,000 mm Frame depth: 1,100 mm Your contact persons in our company: Mr.: Andre Evering Sir: Mario Klöver Mr.: Falk German General information about the article: This item is only available for pickup. An additional desired transport or a shipment of this item is associated with additional costs, which will be charged separately depending on the delivery location or scope of delivery.
Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of Make: 2009 specifications: Conveying width: approx. 1,500 mm Center distance: approx. 9,625 mm Belt course: approx. 3,000 mm horizontally running underfloor, then rising below 30° over a length of approx. 5,875 mm, sloping below 20° on the remaining length and conveying into the press Conveyor belt drive power: 3.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt with 20 mm high T-studs on the sides to seal the belt stringers, ...
Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1750 Year of Make: 2004 specifications: Conveying width: approx. 1,500 mm Belt run: approx. 4,300 mm horizontally underfloor, then increasing over a length of approx. 6,300 mm, Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 1,027 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt with 20 mm high T-studs on the sides to seal the belt stringers, - Belt routing in a neutral zone to avoid stretching tensions, - Chain type M-80 with case-hardened bushings, bolts and roller ...
Electrically heated bogie hearth furnace for a maximum operating temperature of 1280°C. The heating system consists of five control zones. Heating is provided by the sides, rear wall, door and carriage. Heating wire made of APM wire mounted on support tubes. Connected load oven: 75 KW. Incl. 2 fresh air blowers, 2 pcs air heaters, housing cooling with 2 pcs medium-pressure fans, automatic ceiling flaps, insulated stainless steel hood, 2 pcs hearth trolley with SiC plate cover (steerable, on PVC castors, not track-bound) and original switchgear with Windows PC (hardware: Siemens SIMATIC Rack PC). Furnace chamber dimensions (WxDxH): 900 mm x 1,900 mm x 900 mm (= 1.53 m³); Dimensions usable space (WxDxH): 750 mm x 1,840 mm x 850 mm (= 1.173 m³). Weights: Approx. 3,800 kg (oven and attachments); Approx. 850 kg (switchgear).
Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of Make: 2005 specifications: Conveying width: approx. 1,500 mm Belt run: approx. 3,100 mm horizontally underfloor, then rising below 28° over a length of approx. 6,000 mm, Descending below 10° on the remaining length and conveying into the press Conveyor belt speed: 0.27 m/sec. Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt (quality: EP 200/2 2:1) with lateral 20 mm high T-studs for sealing the be ...
Professional meat grinder Duker Rex is designed for fast and efficient grinding of fresh and slightly frozen products with high capacity and reliable performance. This model is equipped with an automatic feeding worm system that enables continuous and even product transfer to the grinding unit, ensuring stable operation and high productivity. The large 120 liter hopper allows processing of bigger product quantities without frequent refilling, while the production capacity of up to 2000 kg/h makes this machine an excellent solution for intensive professional use. It is suitable for processing meat, poultry, fish, vegetables and other food products. The model uses the Unger cutting system with a 130 mm plate diameter, ensuring precise and high-quality grinding with a uniform final product texture. Stainless steel construction provides long service life, high hygiene standards and easy ma ...
Cream cooker CK 120 Rational work in cooking and heating of creams and masses accurate temperature control Digital timer, 2 speeds Boiler filling 120 litres Mass 12 to 78 litres capacity Stainless steel version, thermal oil with handwheel for emptying Machine mobile with brake DGUV V3 tested Connection 400V, 17 kW, 32A, 32A-CEE plug Dimensions 1120 x 905 x 1830 mm, WxDxH Weight 240 kg. NEW Machine 12 Months Warranty + Spare Parts Service Option: Touch Panel LCD Stronger heating Maintenance contract Service Package Instruction & Commissioning Many TOP bakery machines in stock!
Radial Drilling Machine OTTO MULLER Spindle: CM4 Spindle speed: from 70 to 1400 RPM Front table size: 1350 x 550 Back table size: 1000 x 400 mm Slide travel: 1000 mm Maxi distance spindle nose/front table: 600 mm Motor: 2 speeds Maxi column rise: 400 mm Auto descent Drilling/tapping function Spindle speed adjustment by belt variation Hydraulic locking Lubricant pump Voltage: 380 V Dimensions in low position: W 1500 x D 2400 x H 2300 mm Weight: approx 2 T
Brewhouse Tank Farm from 15hl / brew Craft Brewery Complete tank farm / cold block from the 15hl/brew craft brewery, made by Estonian Torsteel in years 2014 – 2016. Tanks are made of AISI 304 and they are insulated pressure tanks. All CCTs have two cooling zones on both sides of the tanks and one cooling zone in cone, BBT has two cooling circuits on side and yeast tank cooling zone is on side of the tank. Tanks are equipped with pressure safety valves, CIP bowl, zone specific temperature sensors, manholes, sampling taps, filling and emptying valves. Tank temperatures is automatically controlled from common control panels. The following tanks are available - CCT 14 x 3000 liters net, working pressure 1.5 - 3.0 bar - CCT 2 x 1500 liters net, working pressure 3 bars - BBT 1 x 3000 liters net, working pressure 1.5 bars - Yeast tank 1 x 300 liters,
81 pallets with scrubbing disc List on request Total weight approx. 60 ton net Total quantity approx. 160,000 pieces VE date 2025/2026 Price on request
Beer Brewery Two Vessel VELO 15hl/brew, up to 4000hl/annum Complete two-vessel beer brewing line manufactured by Italian VELO (now part of TMCI Padovan), suitable for producing a wide range of beer styles—from ales and lagers to non-alcoholic beers and high-strength varieties such as Imperial Stouts over 10% ABV. The standard brew size is 1,500 liters, with the capability to produce two brews during a 10-hour day in peak season. The maximum malt load per batch is 600 kg. Without sugar addition, wort strengths range from 18.5° to 21° Plato; with sugar addition, up to 35° Plato. A complete brew cycle, including CIP, takes approximately 5–6 hours. In regular operation, brewing batches have been overlapped: once lautering and spent grain removal from the first batch is complete, the next brew begins. With 10-hour working days, the maximum weekly capacity is six brews (three ...
Technical data of the pallet rack stand: Shelving system: Nedcon Type: NS The scope of delivery includes: 01x Pallet rack stand, used Material colour: creamy white Frame profile: 1007825 Profile dimensions: 100 x 78 x 2.5 mm Adjustment grid: 50|50 mm incl. cross and diagonal struts, Footplates The stands are pre-assembled (screwed truss) Column height: 9,000 mm Stand depth: 1,100 mm Your contact persons in our company: Mr.: Andre Evering Sir: Mario Klöver Mr.: Falk German General information about the article: This item is only available for pickup. An additional desired transport or a shipment of this item is associated with additional costs, which will be charged separately depending on the delivery location or scope of delivery.
Vacuum diaphragm press Wemhöner type VARIOPRESS model Basic 1000 S Specifications: Heating plate format (mm): 2850 x 1550 Electric heating plate design: aluminium top heating plate Total pressing force (kN): 2400 Chamber pressure max. (bar): 6 Operating temperature max.: 180 degrees Celsius Batch or workpiece size max. (mm): approx. 2460 x 1180 Thermoplastic film as roll goods: Width of the film: approx. 1430 mm Thickness of the foil (mm): approx. 0.25 - 1 Hyperbaric chamber height (mm): max. up to 180 Connected loads: Installed power (kW): approx. 46 Required air pressure (bar): approx. 8
Wohlenberg Guillotine with spare knife, in very good production ready condition. Gives exact cut and everything operational. Can be used to cut other materials rather than paper, such as vinal, plastic, tin, etc.
Vertical manual panel saw Brand: Putsch Type: SVP 133 New machine standard features: - electric driven, automatic shift gate - swivelling centre support for small workpieces (length approx. 3,900 mm) - 4 vertical fixed sawing positions horizontal cuts - 1 measuring stop for vertical cuts - retractable transport wheels - self breaking engine - Preparation for connection to separate extraction system - TRK extraction system (BG wood dust tested) - 400V/3/50Hz - safety devices, sound insulation, tool set for saw blade change - operating instructions and spare parts catalogue technical data: - max. cutting length: 3200 mm - Max. vertical cut : 3200 mm (3100 with digit. dimension display for vertical cuts). - max. cutting height: 1900 mm - highest horizontal cut: 1700 mm - max. cutting depth: 60 mm - engine power: 5 hp (3.7 kW) - saw blade Ø: 250 mm - speed saw ...
32-46-63-80-100 cm3 radial piston hydraulic pumps for sale, new and light used. These pumps are spare parts for plastic injection molding machines that are in stock. Many pumps are fully equipped with proportional valves for control. Each pump is tested and certified. There are also photos of the outside and inside. A personal viewing is also possible on site. Please also take a look at our other advertisements.
Clamping angle, clamping aid -Clamping angle: for workpiece clamping -Wall thickness: 35 mm -Groove: 20 x 60 mm -Dimensions: 275/160/H308 mm -Weight: 28.6 kg
CNC processing centre Brand: IMA Type: BIMA 310V 120/600 Year: 2004 Technical data: Machining area - in X-direction without gluing 6000 mm - in X-direction motor gluing 5000 mm - in Y-direction 1200 mm - in Y-direction with main spindle + WZ-Ø 20 mm 1300 mm max. clamping height from Upper edge of suction plate Z1 100 mm max. workpiece thickness Z 2 depending on equipment/application Worktable height: approx. 950 mm 1 main spindle with feed stroke pneum. - Drive power: 12 kW in S-1 operation - Tool holder: HSK F63, taper diameter =38 mm - Tool feed: automatic - Pull-in force: 11000 N - Tool weight: max. 6 kg - Direction of rotation: right/left rotation, programmable - Speed range: stepless 1500 - 24000 rpm, programmable - Drive: frequency-controlled three-phase motor Spindle lubrication: unique factory grease lubrication - spindle cooling: water cooling ...
Mobile extraction Brand: Riedex Type: DM 160 New machine Technical data: - Motor power 3 kW - Nominal volume flow 1448 m³/h - Associated negative pressure 3000 Pa - Max. volume flow 2000 m³/h - 10.6 m² filter surface - motorised cleaning - Residual dust content
New longitudinal veneer splicer Brand: CASATI Type: LINEA 1250 Technical details: Arm length 1.250 mm Veneer thickness 0,4 - 4 mm Min. veneer length 350 mm Min. veneer width 45 mm Glue for pre-gluing: Urea and PVA Glue for integrated gluing: Urea Feed speed 10 - 40 m/min. Heating area length 1.250 mm Total connected load 7,4 kW Power consumtion approx. 6 kw Compressed air consumption 5 Nl/min Compressed air pressure 6 - 8 bar This machine permits the longitudinal splicing of veneer sheets by applying glue on their edge. Immediately afterwards the veneer will be passing through a heated zone in order to activate the glue reaction: the glue will be hardening thus bonding the veneer sheets. The integrated glueing device allows the joining by one only process. Its also possible to bond pre-glued veneer sheets Option for an extra charge: Cooling device for the glue po ...
Clamping angle, clamping aid -Clamping angle: for workpiece clamping -Wall thickness: 31 mm -Dimensions: 265/150/H200 mm -Weight: 18.7 kg
Hot plate press (electric) Brand: ORMA Type: NPC 6/120 new machine Technical data: Heating plates: 3500x1300mm Cylinder: 6 pieces Press force: 120t Stroke/opening dimension: 450mm Connection value: 28.8kW (ELKOM plates) Options: - Intermediate plate - Anodized surface for ELKOM panels - Parallelism sensor á 1,000.00 EUR - Pressing mechanism from above (fixed lower plate) - Max. temperature till 150°C - Max. temperature till 200°C - 4-sided loading possible - Mylar protective film - Fiberglass Teflon protection - Hardware for Industry 4.0
Polishing machine Brand: BAUERRICHTER Type: SL1 1350X3500 table size: 1400x4000mm work area: 1350x3500mm Note: The specifications and descriptions are a copy of the order confirmation at that time. Data are for information and are not binding.
maximum number of results exceeded
please refine your search
