We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
119,600 used machines on RESALE, but how to find them? Machine Search
maximum number of results exceeded > 1000
please refine your search
new
Boring power: 60,0 mm bore capacity in cast iron: 70,0 mm bore stroke: 260 mm table surface area: 600 x 600 mm thread dia.: bis M 42 M throat: 420 mm turning speeds: 64 - 1210 U/min morse taper: MK 5 feed: 0,1-0,2-0,3-0,4-0,5-0,6 U/min column diameter: 220 mm T - slots - width: 30 mm engine output: 5,5 kW weight: 820 kg range L-W-H: 650 x 1600 x 2640 mm Furnishing: - autom. Spindle feed by electromagnetic clutch - Switch for right / left rotation - Hardened and ground steel gears - Hand wheel for manual fine feed - Gear lubrication by autom. Oil pump - Coolant device in the machine base - machine light - rotating work table - Push button for EMERGENCY STOP - Height-adjustable chip protection hood with microswitch - CE marking The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Three Roll Calender Manufacturer Iddon Bros. ‘I’ shape stack vertical Roll width 54” (1350mm) x 22” (550mm) diam. Even speed Rotary joints for steam heated rolls for water cooling Electrical speed controls with electric autostop Motorised roll stack at the end of the Calender Complete with gearbox, 45kW motor and starter panel The Calendar runs well and goes down to .8mm thick The Calender is mounted on a one-piece fabricated bed plate
used
Capacity (x): 0 Process Application: 0 Other Info: 0 Technical data Aspirated air: 1300 m3/h Voltage 50 Hz 3x: 400 Volt Installed power: 2.2 kW Weight: 125 kg Dimensions: Length: 980 mm Width: 650 mm Height: 950 mm
used
IMS Mammography Giotto Image with the following device components: Tube Varian M-113 SP 0.1/0.3_Bj. 2002 Table top 18x24 and 24x30 • Before taking over, all devices or systems have been tested on site for their functionality. • The system is located in our warehouse in Freiberg / Germany. It is packed on pallets, professionally lashed and with Stretch film wrapped and can be picked up immediately • You buy the system in "ACTUAL" condition from the warehouse Freiberg (EXW), Saxony, Germany, and advance payment. • The sale takes place as "used", EXW Freiberg, Saxony, Germany, to resellers or dealers despite full Functionality without guarantee. • The installation and configuration of the system or plant components must be carried out by a specialist authorised by the manufacturer or technicians!
used
Other Info: Micro Blasting MACH-id 3898 MAKE IEPCO TYPE Peenmatic 620 S YEAR 1999 DIMENSIONS Length 550 mm Width 350 mm Height 400 mm
used
Other Info: Micro Blasting MAKE IEPCO Peenmatic TYPE Peenmatic 750 S YEAR 2000 DIMENSIONS Length 740 mm Width 520 mm Height 500 mm Make : Iepco Swiss Type : Peenmatic 770 S YOP : 2006 No. : 770 - 289 Working internal space Length : 740 Width : 520 Height : 500 Optimal product 500 x 400 x 250 mm Dimensions outside Length : 870 Width   ...
used
Other Info: Micro Blasting MAKE IEPCO Swiss TYPE Peenmatic 770 S YEAR 2006 DIMENSIONS Length 740 mm Width 520 mm Make : Iepco Swiss Type : Peenmatic 770 S YOP : 2006 No. : 770 - 289 Working internal space Length : 740 Width : 520 Height : 500 Optimal product 500 x 400 x 250 mm Dimensions outside Length : 870 Width : 936 Heig ...
used
Other Info: 3.900 x 1.600 x 500 MACH-id 3412 MAKE INNOCENTI TYPE RDG YEAR 60 er SPECIFICATIONS Length 3900 mm Width 1600 mm Height 500 mm T -slot size Cross T slotted Weight a plate approx.5000 Ton Number off matching pieces 15 DIMENSIONS Length 11700 mm Width 8000 mm T slotted floorplate, cast iron plates,
used
COLOR SORTER BY IST ITALY, new in 2017, little use Was used for cereals, legumes, seeds sorting line Replaced by a more sophistcated new one but was in perfect working condition when replaced. Stored in a dry conditions currently. 3+ chutes, 3 for sorting, one for recycling, 256 ejectors or 64 ejectors by chute, 4098 pixels, led lights OUTPUT : till 12 tonnes according to the manufacturer original technical liftlet. Information on request, shipping to any destination Can be seen near Amiens 80, northern France See also website : milin cereal equipment Brittany, France
new
- Ink Tank Sub Assy - HP Part Number CA245-26730 - for HP Indigo Series 2 Machines
new
- Pump for Ink Tank (without board) - HP Part Number CT245-34260 - for HP Indigo Series 2 Machines
new
- ITM Suction Tunnel - HP Part Number CA245-19151 - for HP Indigo Series 2 Machines
new
- Upper Guide Assy for IFR - HP Part Number CT345-16604 - for HP Indigo Series 2 Machines
new
- SP Ink Pump Motor - HP Part Number CA297-00150 - for HP Indigo Series 2 Machines
new
- ITM Bearing Front Replacement - HP Part Number CA290-02951 - for HP Indigo Series 2 Machines
new
- ITM Bearing Rear Replacement - HP Part Number CA290-02941 - for HP Indigo Series 2 Machines
new
- Impression Roller Assy - HP Part Number CA245-22530 - for HP Indigo Series 2 Machines
new
- Outlet ITM Hood Suction - HP Part Number CA254-00072 - for HP Indigo Series 2 Machines
new
- ITM Heater Lamp Assy - HP Part Number CA254-02450 - for HP Indigo Series 2 Machines
new
- Installation JIG for PIP Underlayer - HP Part Number MJX-1336-51 - for HP Indigo Series 2 Machines
new
- Pump for Ink Tank - HP Part Number CA345-16321 - for HP Indigo Series 3 Machines
new
- Ink Tank Sub Assy - HP Part Number CA245-26730 - for HP Indigo Series 3 Machines
new
- IOC 3 Assy - HP Part Number CA354-01151 - for HP Indigo Series 2 and 3 Machines
used
Item No. 4958: 1 gebr. DC Servo Motor Fabr. IJR, type HM IOS-E, with 1000 min-1 Drive power: 0.1 kW
used
WE OFFER AN NICE CONDITION LVD , WE CAN MAKE FOR CUSTOMER AS WELL START UP OF MACHINE INCLUDING TRAINING CUTTING CAPACITY 4KW CUTTING PLATES 6000 X 2000 MACHINE WAS COMPLETE OWERHAULED 2 YEARS AGO - SERVIS COST WAS 35000 EUR LAST SERVICE WAS MADE 6 MONTHS AGO MACHINE RUNNING IN THE PRODUCTION TILL FIRST WEEK IN MARCH 2022 WE OFFER MACHINE LOADED ON TRUCK. NEEDS 2 TRUCK FOR TRANSPORT, NORMAL TRUCK FOR CLIENT WE CAN ORGANIZE TRANSPORT AS WELL WE OFFER MACHINE FREE LOADED ON TRUCK. LASER- GE FANUC C4000 - MODEL E TRANSPORT FOR CUSTOMER WE CAN ORGANIZE AS WELL
used
Box closing machine IMPIANTI Year: 2006 Speed: 7.000 bph Model: Gluer – SUP Gluer hot glue Safety protections
new
DESCRIPTION ITS twin-shaft shredders with low speed and high torque designed to guarantee high performance and maximum reliability in the shredding of tough or bulky materials. Their solid and sturdy construction surpasses any other shredder on the market. As previously said: Given the large size of the grinding chamber and the solid construction, they are particularly suitable for grinding bulky and tough products such as wooden pallets, cardboard cores, metal scraps of various kinds and sizes, stacks of paper / cardboard sheets and many other materials that are usually difficult to grind. APPLICATIONS Large rolled up carpet Cardboard cores Pile of cardboard sheets Metal scraps WORKING PRINCIPLE The material is fed through a loading hopper placed above the grinding chamber which contains two rotating hexagonal shafts, equipped with circular blades of prede-fined thickness w ...
new
: neu : ca. 10 Wochen ab Auftrags : Türkei : 12500 € : 255 € : 1050 mm : 5 mm : 130 mm : 3,5 m/min : 2.2 kW : 2200 mm : 750 mm : 1000 mm : 1200 kg 3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor manual Back Roll forward tiltable upper roll forward and reverse revs conical bending by tilt of backroll movable control panel users manual in ENGLISH or GERMAN OPTIONS: hardened Rolls€ 1.250,- Motorised Back Roll (Power Rear Roll)€ 1.200,- Digital Read-Out€ 1.200,- The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
: ca. 12 - 14 Wochen ab Auf : Türkei : 20000 € : 408 € : 5 mm : 1200 mm : 2,2+0,75 kW : 4,1 m/min : 3000 mm : 750 mm : 1400 mm : 1350 kg : 250 / 2000 mm : 300 mm Mobile control panel Hydraulic clamp on center Gearbox motor with brake Motorized sheet centering system Inside cutting system According to EC safety regulations Operating manual Optional equipment: 1 spare blade set € 1.200,00 Flanging attachment with 1 set rolls € 2.000,00 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
: neu : ca. 12 Wochen ab Auftrags : Türkei : 17300 € : 352.92 € : 2050 mm : 4 mm : 140 mm : 2.2 kW : 3200 mm : 750 mm : 1000 mm : 1650 kg 3 reels asymmetrical roller arrangement - with pre-bending 2 driven rollers by means of a brake motor manual Back Roll upper roller can be swiveled forward forward / reverse run conical rounding by inclining the rear rollers movable control panel OPTIONS: hardened Rolls€ 1.800,- Motorised Back Roll (Power Rear Roll)€ 1.200,- Digital Read-Out€ 1.200,- (sample photo) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
: neu : ca. 10 Wochen ab Auftrags : Türkei : 13000 € : 265.2 € : 1270 mm : 4 mm : 120 mm : 3 m/min : 2.2 kW : 2470 mm : 750 mm : 1000 mm : 1110 kg 3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor manual Back Roll forward tiltable upper roll forward and reverse revs conical bending by tilt of backroll movable control panel users manual in ENGLISH or GERMAN OPTIONS: hardened Rolls€ 1.250,- Motorised Back Roll (Power Rear Roll)€ 1.200,- Digital Read-Out€ 1.200,- The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
: neu : ca. 10 Wochen ab Auftrags : Türkei : 11000 € : 190 € : 1050 mm : 4 mm : 110 mm : 2.2 kW : 1100 mm : 750 mm : 1000 mm : 990 kg 3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor manual Back Roll forward tiltable upper roll forward and reverse revs conical bending by tilt of backroll movable control panel users manual in ENGLISH or GERMAN OPTIONS: hardened Rolls€ 1.120,- Motorised Back Roll (Power Rear Roll)€ 1.200,- Digital Read-Out€ 1.200,- The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
: neu : ca. 10 Wochen ab Auftrags : Türkei : 15000 € : 306 € : 1550 mm : 4 mm : 140 mm : 3,5 m/min : 2.2 kW : 2700 mm : 750 mm : 1000 mm : 1420 kg 3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor manual Back Roll forward tiltable upper roll forward and reverse revs conical bending by tilt of backroll movable control panel users manual in ENGLISH or GERMAN OPTIONS: hardened Rolls€ 1.500,- Motorised Back Roll (Power Rear Roll)€ 1.200,- Digital Read-Out€ 1.200,- The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
: neu : ca. 10 Wochen ab Auftrags : Türkei : 7200 € : 148.32 € : 4 mm : 200 mm : 4 Stk. : 126 mm : 2.2 kW : 16 1/min : 1700 mm : 570 mm : 1200 mm : 500 kg reduction motor with brake system movement of rolls with foot pedal adjustable idle roll steel shafts with bronze bushings 4 set of rolls complete with stand user manual in GERMAN or ENGLISH according to CE rules The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
: neu : ca. 10 Wochen ab Auftrags : Türkei : 14000 € : 285.6 € : 1270 mm : 5 mm : 140 mm : 3,5 m/min : 2.2 kW : 2470 mm : 750 mm : 1000 mm : 1350 kg 3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor manual Back Roll forward tiltable upper roll forward and reverse revs conical bending by tilt of backroll movable control panel users manual in ENGLISH or GERMAN OPTIONS: hardened Rolls€ 1.500,- Motorised Back Roll (Power Rear Roll)€ 1.200,- Digital Read-Out€ 1.200,- The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Kirsch / Iveco Emergency Power System Diesel Generator Power Generation Generator Container Operating hours generator: 411 hours Kirsch Power Generation Unit Type: D 300-4 IWE Year of construction: 2007 Rated power: PRP 240 kW Rated voltage: 400 V Rated current: 433 A Nominal frequency: 50 Hz Rated speed: 1500 rpm/min Weight: 2530 kg Iveco Engine Motor Model: F3BE0685CBXXX Displacement: 12.9 liters Specified kW (BHP): 330 (442,50) at 1800 rpm Fuel consumption at specified power: 245mm^3/stroke
new
: neu : ca. 12 Wochen ab Auftrags : Türkei : 3500 € : 1 : 1.2 mm : 100 mm : 140 nm : 8 Stk. : 62 mm : 0.75 kW : 32 1/min : 900 mm : 450 mm : 1350 mm : 135 kg DEMO MACHINE Haevy duty cast iron main frame Brake motor Foot pedal Adjustable lower roll 8 set of rolls Complete with stand User manual in ENGLISH or GERMAN The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Max Sheet: 750x1050 mm Min Sheet: 350x400 mm Min Paper: 90/100 gr/m2 Max Mater: 1,8 mm Max Wave: 3,0 mm Preasure: 300 Atm Centerline-System Quickspanner in Stripper Blanker 30 cm elevated Max speed: 9000/hour Working-hours: 53.000
used
Year of construction: 2010 Control: NC control PC base Touch control panel Networking Spindle: HSC SK30 Tool changer: 5 fold 5 axes Isel linear guide Parts unit: Harmonic Drive A-axis Omron Engines Blank clamping via A-axis such as lathe with tailstock Machine frame kpl. Aluminium Plexiglas window on all sides Two large sliding doors Large recess for suction under A-axis - Technical errors and prior sale reserved. -
used
automatic workpiece loader - max bar length: 720 mm - max dia: 65 mm Previously used on Mazak CNC lathe
used
automatic workpiece loader - max bar length: 720 mm - max dia: 80 mm Previously used on Mazak Multiplex 620
used
For marking on almost all metals and plastics, including most metals made of steel, stainless steel, brass, Bronze, gold, silver and similar materials as well as wood, glass, ceramics, leather, fabric and organic materials. Software: Marking software - QuickMARK ™ easy-to-use professional laser English in standard version Highlight Characters - All keyboard text characters and symbols. Programmable characters height, width, spacing, linear Position, angle and circumferential position Highlight Font - Selectable highlight fonts; Windows TTF fonts and continuous line fonts, All content in the text can be adjusted flat or curved. Content of the automatic tagging - serial numbers, shift codes, content from barcode reader, real time and date. Simultaneously import and markup content from a text or Excel file. External Content Management - Importing and tagging content from a host on the net ...
used
Rod diameter 5-102 mm Rod length 1600 mm
used
proximity switch -Manufacturer: IPF Electronic -Product type: IV400720 -Number: 24x available -Price: per piece -Weight: 200 g
used
transformer -Type: IS -Art.Nr.: 700175 -Primary: 400 V -Secondary: 230 V 4.35 A. -Dimensions: 150/155/H130 mm -Weight: 12.6 kg
used
Circuit board for glass cutting table, glass cutting table, glass cutting machine -Manufacturer: INNOLAS -Type: ZSB circuit board Impala 6x -Weight: 0.1 kg
used
Used weighing and packaging machine used for packing granules by TÉCNICAS MECÁNICAS ILERDENSES SL. model ILERSAC LBSD. New 2013. TECHNICAL DATA: PRODUCT CHARACTERISTICS: - Product BLACK COAL IN PROSPECT. - Density 340 / 645.16 kg/m3 - Fluidised Yes - Granulometry 30 µm - Sack type PAPER - OPEN BAGS - Bag weight 12 kg - Dimensions of bag 740x500x160mm - Dimensions of CP1 pallet 1200x1000x150 - Maximum pallet height 1800 mm Maximum production of 90 bags/hour CONNECTIONS: - Electrical connection 380V III+N+T 50 Hz - Installed power 12 kW - Control voltage 24 V - Air pressure 6 bar - Air consumption 150 NL/min. - Aspiration 1900 m3/h - 21 m/s Main features: - Programming of reading stability conditions. - Programming of weighing cycle and autocorrection parameters. - Zero variation detection range. - Precision: 5000 homologated divisions. - 50 operating reci ...
We sell 1 x IBM zSeries BC12, 2828-H06/I02 In most cases, the entire item can only be handed in completely. More information on request. In most cases, advertised products can only be sold as a complete lot. More information on request. We look forward to receiving inquiries from Germany and internationally. We have many other refurbished/used hardware available from the areas of the systems mentioned here as well as from other systems of these manufacturers: IBM, DELL, HPE, ORACLE, NETAPP, QUANTUM, STK, FUJITSU, SGI, HDS, EMC, Supermicro, BULL, NEC, CRAY, 3Com, ADVA, Alcatel, Brocade, Cisco, Enterasys, Extreme Networks, Huawei, Marconi, Nortel, Qlogic, Avaya, ORACLE Tested, tested used hardware at a reasonable price from HASCON! The sale is only made to companies. We have available complete systems and components in refurbished conditions from all these manufacturers ...
used
Description IML molding plant consisting of: - Robbi robot 115 JS: mat. 10363 (on press) - Robbi robot 85 JS: mat. 10363 (finished parts palletizer) - Bank for loading labels - Conveyor belt for evacuation of finished parts
used
24 pieces drillholder for INDEX MS32 / MS42 tool holder 1 inch Please, contact us for getting more information and pictures on mail(at)tar-mc.com or www.tar-mc.com