cutters used for sale

Category New machines Subcategory Mechanical Treatment of Meat Type New Bowl choppers Warranty 12 months Height 1350 Width 2290 mm Length 1300 mm Weight 1800 kg Voltage Electrical: 400V 50Hz 3N Installed Power 39.9 kw Main material Stainlees Steel

With the three-head roller saw, plastic-coated films can be sawn from wide roll to customer roll. With the system, film rolls can be sawn on 3" and 6" cardboard or plastic sleeves. The first cutting head is firmly positioned and defined as a master. The other two cutting heads are positioned to the master on the desired cutting width. A maximum of 2 benefits are possible. Sawing operations can be sawn dry, or wet by a wetting device of the saw blade. • Mesh type: Saw Material: Foil • Cutting system: circular saw s600 mm ( 3 saw cuts ) Saw cutting width: 6mm • Space usage: 7m x 4m Dimensions machine: 4.20m x 2m (height closed 2.15m, open 3,50m Sleeve width max.: 2700mm Cut width max.: 2620mm Cutting width min.: 500mm • Rolls max. : 550mm • Rolls min. : 200mm Sleeve diameter: 76mm/152mm

see photos

LINEAR MILLING MACHINE PADE UNIZE 6 number of aggregates 6 2 milling 2 x 7.5 kw engines 2 universal: milling or grinding 6.6/8 kw two-speed engines 2 grinding 3.7 kw engines included tool

Freezer cutter Rühle GFR 450 in a very good used and functional condition. Completely made of stainless steel, guillotine technology, cutting material temperature down to -20°C, capacity up to 3,000 kg / h. Holding device for 200 l cutter trolley. Throughput width 61 cm, throughput height 33 cm. Dimensions W/D/H 80/230/140 cm. Connection values 400 volts, 7.2 kW, 12.3 A. Workshop tested, immediately ready for use. More on request.

Control Board A1

- Flat steel shear cuts flat up to 100 x 18 mm - Knife length approx. 250 mm - Profile steel scissors cut angles 90° to 100 x 10 mm 45° to 70 x 8 mm - Bar steel shear cuts round steel 90° to 36 mm Square steel 90° to 30 mm - Notching device sheets up to 8 mm - Hole punch - Pressure capacity approx. 50 t - Projection 350 mm - punched in steel up to 20 mm Ø in 15 mm - Drive 400 V / 3 kW - Space requirement approx. W 1100 x H 1700 x D 2300 mm - Weight approx. 1900 kg

Diameter: 0 mm Width: 0 mm Bore: mm Tangential head for gear hobber RS 2 - also available: Tangential head for gear hobber RS 00 ! The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

- technically efficient, ready to work – after full service - 6 spindles - automatic - variable angle lower spindles - spindle top 90 degrees

Diameter: 360 mm Width: 120 mm Bore: nicht schwenkbar mm milling head: The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Description: with traces of storage DP 7 20° KHSS-E Approx. Onsite Dimension. (l x w x h): 0 x 0 x 0 mm, weight approx.: 0 kg

SPECIFICATIONS: Single chain Vertical machining Table enviable Equipped for the processing of doors.

Guillotine Ideal Model 4810A Year 1989 Cutting length 475 mm Details Manual adjustable clamp Electric cutting Manual backgauge adjustment Ruler read/out 2 new knives, 1 used single phase, 240 volts

Type: W/ARW 2200/12 Flying Splice Comm. 2011-001.1 Working width: 2200 mm Finished roll weight max. 2000 kg Finished roll diameter max. 2x 1200 mm Finished roll width min. 800 mm; max. 2200 mm Material Paper/ Foils 75 μm – 1000 μm Machine speed max. 1500 m/min Depending on the type of material and material thickness achievable Web tension: max. 1000 N Finished roll sleeves: inside 152.4 mm outside 162.4 mm - Type of cardboard sleeve, plastic - Sleeve tolerance according to DIN 6748 or 55470 Unwinding: Type ARW 2200/12 Unwinding: axisless 2 x 1200 mm; sleeve holder 6" L.W. (other dimensions with additional accessories possible) Sleeve holder: 6" L.W. (other dimensions with additional accessories possible) Pulleys: DM approx. 150 mm Brake: Generator brake with energy recirculation, control via ultrasonic sensor Path control: Edge control E&L with ultrasonic sens ...

Microcut/ continuous cutter, colloid mill. High-performance machine for use in continuously operating process lines. Product - Mounting funnel: capacity 30 liters completely in V2A Nirosta stainless steel, 3 different perforated discs - inserts and 5 sets - knife blades

for frozen meat blocks

Very high quality cone cutter from Makita 55013 Ready to use Beam height up to 400 mm Range up to 240 mm Cone racks 0 to 130 mm Cone length maximum 340 mm Motor power 2.2 Kw lateral adjustment range 45/20 mm Dimensions 100cm x 64cm 110 (length-width-height) Weight approx.120 Kg For head houses the workpiece is clamped schraeg

REF-1681 SACCARDO ARTURO CHOP CUTTER Completely made of stainless steel. Manufacturer: SACCARDO ARTURO Model: TITANIO 2. Max. cutting length: 1.070mm. Max. cutting section: 210x240mm. Cuts per minute: 90-180 Cutting thickness: 5-60mm Weight: 330 kg. Year: 2008 3kW Dimensions of the machine: 2,367mm x 832mm; h: 1,496mm

– Capacity 50 tons – Hydraulic – 4 stations – Foot control – Electric backgauge - Emergency stop Ebhzaoz – With 10 stamps (8, 10, 12, 14, 16, 18, 20, 22, 24, 26 mm) – Peddinghaus punching recording – Documentation – 400 V

Vibrator PROFILINE RLA-H.7S, max. format 1220 x 1640 mm with spread roller and pneumatic push-out to the rear, Auto. Rear table assembly with plier transport system AM 1220x1640 mm High-speed cutter SCHNEIDER SENATOR 185 SC-Video Cutting width max. 1850 mm Stacker ABS 145-7B , max. format: 1220 x 1640, max. stack height 1450 mm Footprint approx. 8 x 8 m

Chain milling machine VEB Type KFM Motor power 2.2 kW Table tiltable 30° -0°- 30°, height adjustable, adjustable to left-right Pressure from the front Sword 50 x 150 for chain 12 – 17 mm Dimensions 1100 mm x 1000 mm x H 1620 mm Weight with pallet 511 kg

Groove milling machine make BUSCH type NF 1Machine -No: 1/494 built in 1963Projection: 200 mmSpindle length: 250 mmTable size: 250 x 610 mm4 spindle speeds: 380-1500 rpm.Drive power: 9.8 kWExternal dimensions: 1050 x 900 x 1800 mmused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Type: Microcutter Brundeler Holeplate diameter 175 mm Capacity: up to 2500kg/h Hopper capacity: 150 liter Machine dimensions in сm: Length: 170 Width: 80 Height: 105 Power: 37 kW Delivery time: 20 working days after payment

SPECIFICATIONS: Engine power HP: 3 Vertical leadership support Replacement tools available

Manufacturer: Schneider-Senator Model: E-Line 78 year: 2009 Available: 01.May 2022 Location: germany Price: on request

1 HOZA (Germany) pinking machine type ZEN 80 (Zigzag cutting), knife width 820 mm, working width up to 800 mm, new serrated knife with 6 mm serration gauge, machine equipped with precise hand lever feed mechanism, feed mechanism settable for 2 measures between 0-320 mm, with security light guards, 3 x 380 V, 50 Hz

1 MARGASA textile waste cutting machine type CMT 600 rotary cutter, year 1996, working width 600 mm, cutting blade width 610 mm, feeding conveyor 250 cm long, exit conveyor 190 cm long, supplied with blade sharpening table and spare blade

Equipped with: Digital computer program with TFT color screen Security photocells Central table with air Side tables with air - Perfecta BSH 3 pile lift ( 2011) - Baumann vibrating table with air removal roller - Unloader Perfecta BA 3N ( 2011)

-Massive construction, stainless steel beams and posts; -Dimensions: W=720 mm., L= 1250 mm., H= 1470 mm.; -Power: 4 kW, 400V, 50Hz; -Adjustable legs; -The machine is an analogue of the Magurit Fromat 042 guillotine; -Complete hydraulic system of the Hydac company. -Electrical part of Telemechanics; -Knives from Germany; -Reinforced design of the knives; The blades are as follows: two upper horizontal, one lower horizontal and three vertical. -Loading the blocks: the blocks of frozen meat are placed in a chute equipped with a pneumatic cylinder that lifts it for easier loading. -After cutting, the products are unloaded directly into 200 liter carts. -With a lifting device for the moulds -Complete with vertical dicing knives -Capacity: 2000 ÷ 2500 kg. / h. Loading the blocks:The blocks of frozen meat are placed in a chute equipped with a pneu ...

Guillotine for slicing frozen meat with a capacity of 8000 kg. per hour It can cut molds of frozen meat with a temperature of -15°C to -3°C without defrosting the product during processing. The processed product is unloaded directly into Laska type carts. Technical parameters: Models IB – 4 IB – 8 Productivity- kg / hour up to 4000 up to 8000 Capacity kW 15 15 Max. weight of pieces gr. 200 450 Min. block temperature: -18 °C -15 °C Block dimensions mm. 600 / 400 /200 Machine dimensions: length 1400 width 1130 height 1680 Weight of the machine kg. 720

Fezer chain milling machine Motor power 1.5 kW With door support Weight approx. 150 kg

REF-2278 TREIF PUMA-CE AUTOMATIC CHOP CUTTER Automatic chop/cutlet cutter by TREIF Model: PUMA-CE Type: 1930 Year: 1995 220/380V. 3-phase. 50Hz Overall dimensions: length 2,600mm, width 900mm, hauteur 1,400mm

3 trimmers horauf SN140, automatic , in very good condition, year 99

Stock # U2397-4 Used stainless steel micro cutter/emulsifier by Haarslev A/S (DK) model HF 175. Machine is designed for emulsifing a product, paste type. Can run on meat, chicken, pork etc. Output depends on product and can reach 3-4 tons per hour. Feeding inlet into milling chamber has diameter 105 mm. Machine has stainless steel shaft driven directly by el motor 55 kW, 2950 rpm, 380 V, 50 hz. On the shaft there are mounted two sets of six blade knives and screens. First screen has diameter of holes 1.2 mm. Second screen has holes with diameter 0.8 mm. Knives and screens are designed in non-corrosive steel. Body of milling chamber designed in stainless steel. Discharge via outlet with diameter 65 mm. Machine has local control panel and is mounted on four legs. Includes technical documentation. Last time used in food industry.

1 KAPPA pinking machine type 105 S knife width 1040 mm, serration gauge 4 mm machine equipped with precise hand lever feed mechanism, with laser cut indicator, motor power 3 kW, 3 x 380 V, 50 Hz, Machine with setting for 2 pattern dimensions (normally supplied with 1 only), machine delivered with 2 new cutting boards (one to be used and one as spare), with installed cutting knife plus spare cutting knife Machine in pristine condition. It was bought for a project and was never really used. Delivered secured on it's wooden crate

The machine is adapted to crush frozen meat blocks to a temperature of -20 degrees Manufacturer: Magurit Model: 545 Height: 1800 mm Width: 1100 mm Length: 2590 mm Electric power supply: 400V 50Hz 3N Power: 5.5kW Efficiency: 5t

year 1994,Digital program,Air table ,Light guards,Side tables with air,2 knifes in complete working conditions. Available immediately

Digital program 999 positions Air table, In production Free of damages

SOITAAB CNC plasma cutting with 2 generators Year = 1998 Plant size: center distance = 6000 mm. Useful length 24 thousand mm. Implant length = 26 thousand mm. Speed allowed with double motorization 20 thousand mm./ min. Operating speed up to 5000/6000 mm./min Numerical control = OSAI 10/310 TFT with 10.4 "color monitor Plasma generators No. 2. - Hyperterm HT 2000 System in operation, complete with bench and NOVA VIT fume extractor complete with star valve, direct discharge of cutting dust in standard big bags.

Product number: 2462B Type: KB428 Serial number: C722 Block size: max 530 x 530 mm Power: 3 x 380V, 50Hz, 22kW Dimensions:950 x 1450 x 1900 mm 1 speed on cutting drum Product bottom exit in 200 litre tote bins

REF-1059 CHOP CUTTER CRM NEXUS 220 Manufacturer: CRM (COSTRUZIONI-REVISIONI-MECCANICHE) Model: Nexus 220 Year: 2003 Entirely built in stainless steel Power: 4kW 220/380V, 50Hz. Three-phase Inner dimensions: - Max. piece length: 900mm - Max. piece height: 260mm - Max. piece width: 220mm Outside dimensions: Length 2,130mm, width 800mm, height 1,200mm

- German production - DTR, CE - year of manufacture 2010 - high efficiency up to 200 elements / min - 28 km / 8h TECHNICAL PARAMETERS: Wood parameters - width 60 - 225 mm - thickness 18 - 48 mm - length 300 - 2000 mm - pressing length 8100 - 16400 mm - power consumption 150 kW - air consumption 3100 Nl/min - suction capacity 14845 m3/h - two milling stations - undercutters - connecting to the line and zyzgka - loading with a conveyor with spacers - package width 600 mm - split ironing length Dimensions of the folding machine - length 42000 mm - width 6000 mm - height 2100 mm

Control: Fidia C20 with handwheel Areas of work X-axis: approx. 5,000 mm Y-axis: approx. 2,700 mm Z-axis: approx. 1,250 mm Clamping table Length x width x height: approx. 5,600 x 2,740 x 520 mm (cast iron) Table load: max. 15,000 kg T-slots and distance: 10 x 22H8 / 255 mm Milling spindle Spindle power: 8 kW Spindle speed: 6,000 rpm Tool holder: 78/8 flange Tool tensioning: manual with union nut Drives Linear axes Caiquw7evf Feed speed X-, Y-, Z-axis: up to 20 m/min Axle acceleration X-, Y-, Z-axis: up to 1.5 m/s2 Connection data Connected load: approx. 28 KW Fuse: 63 A Dimensions, weights Machine space requirement: approx. 8,000 x 5,000 x 4,500 mm Total weight: 25,000 kg Condition of the machine Fully functional condition, regular maintenance by machine manufacturer. Machine already dismantled and stored. At call!

Control: Fidia C20 with handwheel Areas of work X-axis: approx. 5,000 mm Y-axis: approx. 2,700 mm Z-axis: approx. 1,250 mm Clamping table Length x width x height: approx. 5,600 x 2,740 x 520 mm (cast iron) Table load: max. 15,000 kg T-slots and distance: 10 x 22H8 / 255 mm Milling spindle Spindle power: 8 kW Spindle speed: 6,000 rpm Tool holder: 78/8 flange Tool tensioning: manual with union nut Drives Linear axes Caiquw7evf Feed speed X-, Y-, Z-axis: up to 20 m/min Axle acceleration X-, Y-, Z-axis: up to 1.5 m/s2 Connection data Connected load: approx. 28 KW Fuse: 63 A Dimensions, weights Machine space requirement: approx. 8,000 x 5,000 x 4,500 mm Total weight: 25,000 kg Condition of the machine Fully functional condition, regular maintenance by machine manufacturer. Machine already dismantled and stored. At call!

Stephan MCV10 Microcut, continuous cutter, colloid mill, koial mill, emulsifier Voltage: 400V Speed: 2850rpm Stainless steel funnel Machine heavily soiled and with rust deposits on the housing without nameplate very loud run, because bearing damage, therefore sale as spare parts donor or hobbyist object Video about test run available

WUPA PS 4.1 year 1973 - 2003 refurbished size 800 – 1,120 mm Min. size 360 – 500 mm Min. grip 14 mm weights 100 – 1,000 g/m2 Thickness max. 3 mm pressure 240 t Speed max. 4,000 sheets/h Stripping

Profile steel shears

Cutting machine EBA 550 Year of construction 2007

Machine type: Profile steel shears with punching Manufacturer: PEDDINGHAUS Model: 5-fold combined profile steel shears with punching Condition: very good Offer type: used machine Specifications: Achievement: round = Ø 20 mm, flat = 80 x 12 mm Angle steel = 50 x 50 x 6 mm T-steel = 50 x 6 mm Drive type: by hand Note: two machines on a stable, mobile substructure Weight: 200 kg The machine is in a very good and immediately ready condition and can be visited and demonstrated by us. We would be pleased if you are interested in our offer. Errors, changes and prior sale reserved.

SECOND-HAND MILLING MACHINE FOR CORNER SEATS COMEC MOD. FAS2 - S/N 951106 -Volt. 380/50