cap mould used for sale

Single-station machine for articles up to 5 ltr. Extruder 80/24D, double head 160 mm center to center. Trim cutting in the machine. 460V 60 Hz Good condition

gebr. Table milling machine MARTIN T27 Fix (rigid milling machine – not swivelling!) Year 2008 Operating hours: 493 h (see last picture) Motor power: 7.5 / 9.5 kW (amplified motor power) Rated current: 24 A Speeds: 3rd / 4th / 5th / 6th / 8,000 / 10,000 rpm Max. diameter milling tool: 250 mm Max. diameter of slitting tool: 350 mm electr. Height adjustment (stroke: 150 mm) Touch screen control (program memory: 100 / tool memory: 500) Table size: 125.5 x 90 cm Milling spindle: 30 + 40 mm MARTIN Cast Stop Jaws Engine brake Spindle blocking: pneumatic Central lubrication Suction nozzle: 2 x 120 mm Dimensions: 295 cm x 140 cm x 186 cm (L x W x H) Weight: approx. 1,300 kg Extras: Electrically adjustable table opening (infinitely variable) Electrical positioning of the milling fence (mechanical infeed jaw) Swivel device for milling fence Centrex Protection (Aigner) ...

This belling machine from Thyssen Nothelfer is a very complete line. The line is disassembled and has a throughput of up to 10m pipe length. – Brand: Thyssen Nothelfer – Year built: 1996 – Max. tube Ø: 500mm

Superset NT 31 with 14 axis control and 1000 programs Feed rollers in front of the dressing spindle Position 1 - Dressing spindle Position 2 - Right spindle with 2 axis ( up / down ) Position 3 - Left Spindle Horizontal Top with 3 Axis (Up/Down and Diameter Setup) Position 4 - First Horizontal Spindle with 2 Axis (On/Off and Diameter Setup) Up/Down Coupled with Position 5 Position 5 - Second Lockers Horizontal Top with 3 Axis ( Up/Down and Diameter - Setup ) Position 6 - Second Spindle Horizontal Bottom with 2 Axis ( Up / Down ) Motors 6 x 7.5 KW Feed Continuously variable from 6 to 36 rpm with 4 KW Feed roller before and after position 2 Vertical Right with axis control ( on / off ) Planer heads 5 pieces on position 1-2-3-4-5 type. TERSA

3 sets of blowing moulds for KHS SIG Blomax 8: 1 complete set for 330 ml blowing moulds (8 pieces) 1 complete set for 1000 ml blowing moulds (8 pieces) 1 complete set for 1500 ml blowing moulds (8 pieces) Type of the blowing machine Blowing machine KHS / SIG type: BLOMAX 8 III year of manufacturing: 2004 capacity: max. 13.000 bph neck finish: PCO 28 - 1881

Weibert WJ-F10 Swivel spindle milling machine Milling machine: swivel 90°-45° Milling U/min 1400/3500/6000 and 8000 Sliding table 1150mm (Optional 1600mm) Engine power: 400V 3 KW (4.0 hp) WY-600100 Options at extra cost: Telescope 900mm WJ-600108 Eccentric tensioner Milling motor 4 KW (5.5HP), S1 100% Milling motor 5.5 KW (7.5 HP)S1, WJ-600102 Milling spindle 40,50 or 60mm, Integral safety rails 500mm, WJ-500111 Right and left-hand milling machine, WJ-600106 Table extension right/left, WJ-600107 Feed

HM501, 3-fold head stitch 70. New Beckhoff PLC (Retrofit 2021)

HS451, YOC 1993, Retrofit 2021 Available with 1-fold/2-fold head/3-fold, bottle test Optionally with E-extruder

Used blow moulding machine made by KRONES model Contiform S18. New 2004. It has 18 blow moulding stations. The maximum blow moulding speed is 24,000 bottles per hour for the 2.0 l format and 28,000 bottles per hour for the 1.5 l format. In February 2024, the machine was upgraded to support the PCO 2622 thread. The blow moulding machine has an integrated control system with visualisation in Polish, English and German. A complete set of documentation is included with the blow moulding machine. The blow moulding machine includes: an automatic glycol cooler, an automatic preform feeder, an automatic preform basket tipper and a bottle ejector mounted on an air transport conveyor.

Substructure painted Automatic machine with chain drive width: 450 mm Band height: adjustable Spray nozzles: 3 pcs. With pressure control Technically repaired

Used blow moulding machine made by SIPA model SFR24. New 2007. It has 24 blow stations. The maximum blow speed is 38,000 bottles per hour for the 1.75 l format and 41,000 bottles per hour for the 1.5 l, 1.25 l, 1.0 l and 0.7 l formats. The device has an air recovery system and linear optical control for testing the quality of preforms. Supported thread type: PCO 1881. The blow moulding machine has an integrated control system with visualisation in Polish, English and Italian. A complete set of documentation is included with the blow moulding machine. The blow moulding machine includes: an automatic air-cooled chiller for supplying the machine with cooling water, an automatic preform feeder, an automatic preform basket tipper and a bottle ejector mounted on an air conveyor.

TECHNICAL DATA: Vertical milling machine Tool shank diameter mm: 35 Dimensions of the work table mm: 2400 extendable in width 4 speeds, self-braking Installed capacity KW: 5,5

Output (caps/min): 1500

Code: 0234 Brand: SPANEVELLO - ITALY Model: SC 17 Automatic 7-spindle moulding machine for window frames, frames, profiles, joinery, carpentry, wooden packaging and various Technical data: Sturdy structure with electro-welded steel base Working width 170 mm Working height 120 mm Variable feed speed 5/25 mt/min Automatic lifting of upper beam Composition: 1° spindle: Surface planer - Motor Hp 4 2° spindle: Right vertical spindle moulder - Motor Hp 4 3° spindle: Left vertical spindle moulder - Motor Hp 4 4° spindle: Right vertical spindle moulder - Motor Hp 4 5° spindle: Thickness planer - Motor Hp 7,5 6° spindle: Right vertical spindle moulder - Motor Hp 4 7° Universal spindle 180° - Motor Hp 8,5 Diameter of shafts of working heads mm 40 Shaft rotations of working heads 6000 rpm Power of feed motor Hp 2 Suction inlet diameter 150 mm Overall  ...

Brand: Martin Type: Table milling machine with heavy tenon table Spindle: ø30 mm Motor: 4 KW

Key data: 4200 mm, 1090 , 70

Screw diameter: 70 mm Injection weight in polystyrene: 1090 g Clamping force: 4200 kN Screw diameter: 70 mm Stroke volume: 1212 cm³ Injection weight in polystyrene: 1090 g/hp Injection pressure: 1,877 bar Clamping force: 420 t Lights Tie bar spacing H x V: 810 x 710 mm Tool installation height - min.: 380 mm Opening distance: 710 mm Microprocessor control: NC4 Screen text: German Operating instructions: German FHK interface for robots: Euromap 67 Core pull: 2 x Without material hopper / Without water battery: -/- Pump drive power: 45 kW Total connected load: 82.4 kW Total weight: 20,000 kg Total size: 7.9 x 2.3 x 2.5 m Payment terms: 100 % before taking over the machine, net only

Key data: 3500 mm, 810 , 60

Screw diameter: 60 mm Injection weight in polystyrene: 810 g Clamping force: 3500 kN Screw diameter: 60 mm Stroke volume: 891 cm³ Injection weight in polystyrene: 810 g/hp Injection pressure: 2,420 bar Clamping force: 350 t Lights Tie bar spacing H x V: 720 x 720 mm Tool installation height - min.: 350 mm Opening distance: 730 mm Microprocessor control: NC5 Screen text: German Operating instructions: German FHK interface for robots: Euromap 67 Core pull: 2 x Without material hopper / Without water battery: -/- Pump drive power: 55 kW Total connected load: 78.1 kW Total weight: 17,300 kg Total size: 7.4 x 2.0 x 2.4 m Payment terms: 100 % before taking over the machine, net only

Brand: Martin Type: T25 M-No.: V172604 Year of construction: 1990 Motor power: 5/6 kW Swivel milling spindle: -5° - +45° Milling mandrel : 30 mm Height adjustment milling spindle: 150 mm Speeds: 3000/4500/6000/9000 rpm Cone of the milling spindle: MK5 Table size: Table extension 2,500 mm and table distribution (= extendable support) Automatic milling spindle start-up/bremzing via rotary knob Control panel: eye level with digital reading Spindle height -5° - +45° electromotive angle adjustment with digital readout Inclination -5° - +45° 150 mm Electromotive heights Adjustment with digital readout Feed: five-pole. Socket with operation via central control

Key data: 2500 mm, 521 , 55

Screw diameter: 55 mm Injection weight in polystyrene: 521 g Clamping force: 2500 kN Screw diameter: 55 mm Stroke volume: 570 cm³ Injection weight in polystyrene: 521 g/hp Injection pressure: 2,470 bar Clamping force: 250 t Lights Tie bar spacing H x V: 630 x 630 mm Tool installation height - min.: 300 mm Opening distance: 550 mm Microprocessor control: Selogica direct Screen text: German Instruction manual: German FHK interface for robots: Euromap 67 Core pull: 1 x Without material hopper / Without water battery: -/- all-electric injection moulding machine Total weight: 14,500 kg Total size: 6.7 x 2.1 x 2.3 m Payment terms: 100 % before taking over the machine, net only

SPECIFICATIONS: Table size: 2200x450 mm (extendable) Installed power: 5 Kw EQUIPMENT: Drive on 3 rollers Accessories

Key data: 3200 mm, 287 , 50

Screw diameter: 50 mm Injection weight in polystyrene: 287 g Clamping force: 3200 kN Screw diameter: 35 or 50 mm Stroke volume: 141 /314 cm³ Injection weight in polystyrene: 154 / 287 g/hp Injection pressure: 2,500/1280 bar Clamping force: 320 t Lights Tie bar spacing H x V: 720 x 720 mm Tool installation height - min.: 300 mm Opening distance: 600 mm Microprocessor control: Selogica direct Screen text: german Instruction manual: german FHK interface for robots: Euromap 67 Core pull: 2 x Without material hopper / Without water battery: -/- all-electric injection moulding machine Total weight: 14,500 kg Total size: 6.5 x 2.1 x 2.2 m Payment terms: 100 % before taking over the machine, net only

Type 1B/1K-M length of workpiece. 5000 mm workpiece width. 300 mm Quontity of mortising: 180 mm working height 1/Max 20mm Number of motors 2/380 V 50Hz Air pressure 6 bar Made in Italy 2007y Transport dimensions 4200x2000x2400mm Weight 2000 kg Price 7500 Eur (EXW Jonava, Lithuania)

SPECIFICATIONS: Working table: 1100 x 900 mm Spindle: Ø 40 mm Manual adjustment Engine brake Installed power 5.6 kW Additional: Various tools

Two-station machine for stacking canisters up to 10 ltr. Year of construction 2000. With PWDS and SFDR. Clamping force 200 kN. With aftercooling stations and needle bubbles. Also included is the conveyor belt for canisters. Good condition

SPECIFICATIONS: Working table: 1050 x 970 mm Sliding table Spindle: Ø 35 mm Manual adjustment Engine brake Installed power 5.60 kW Inclusive: Various tools

SCM Spindle Moulder Model T150 with Tilting Shaft - spindle moulder shaft inclination -10 / +45 degrees - spindle moulder shaft diameter 35mm - max tool diameter with profile guide 250mm - maximum tool diameter that can be retracted under the table 320mm - "Fast" sector table for optimizing the support of the piece under the tool, adjustable from the outside, as an alternative to the table rings Machine with: Flat "LL" version with 2 profile extensions - length 2500mm, complete with adjustable front support bar for large pieces, and with emergency button Guide and spindle moulder shaft with electronic programming Complete with: - Hanging control panel - total excludability of the guide from the plane - 3-axis microprocessor electronic programmer for automatic programming of the different Positions : spindle moulder height Spindle moulder tilt Positioning gui ...

WEINIG moulder model UNIMAT 17N with 8 shafts: -useful working measures 170x120mm -gimbal towing and pneumatic pressure -variable feed speed -top feed wheel before the 1st shaft -tandem feed groups in front of the 2nd and 4th shaft -2000mm long entrance plane -with SACOT automatic loader -manual lubrication pump of the table Tree layout: 1-under 2-right 3-left 4-right 5-above 6-under 7-above 8-Universal

Serial number: X42252 Machine type: Injection Moulding Machine Clamp unit: 400T (Tonnage Group G0 400T–450T) Injection unit: 5600 Injection Specifications: - Screw Ø: 97 mm - Screw type: GP mixing for G - Intensification ratio: 9.42 - Max. shot weight (PS): 253 g - Injection capacity (cm³): 3394 - Injection rate: 550.4 cm³/s - Max. screw stroke: 450.2 mm - Max. hydraulic injection pressure: 170 bar - Specific injection pressure: 1600 bar Clamping Unit: - Tie bar spacing: 750 mm × 750 mm (H × V) - Mould height: 300 – 885 mm - Max. platen distance: 1605 mm - Location ring Ø: 175 mm - Location screw (MX): M20 - Core pulling: 2 sets Power Requirements: - Voltage: 400 V - Drive power: 124.3 kW - Heating wattage: 44 kW - Total power: 168.3 kW - Current requirement: [Not specified] Robot: ATM ES2000 Max. water heater temperature: 95 °C Machi ...

SPECIFICATIONS: Swiveling spindle milling machine Table size mm: 1200 x 820 vertical spindle stroke length mm: 180 I Spindle diameter mm: 50 II Spindle diameter mm: 30 Powerlock Spindle speed: 10,000 rpm. Motor power KW: 7,5 Complete with: -Control panel - 4-roller feed with variable adjustment

Serial number: X41520 Machine type: Injection Moulding Machine Clamp unit: 400T (Tonnage Group G0 400T–450T) Injection unit: 2500 Injection Specifications: - Screw Ø: 84 mm - Screw type: GP for GF - Intensification ratio: 9.7 - Max. shot weight (PS): 2018 g - Injection capacity (cm³): 2106 - Injection rate: 415.4 cm³/s - Max. screw stroke: 380.2 mm - Max. hydraulic injection pressure: 165 bar - Specific injection pressure: 1601 bar Clamping Unit: - Tie bar spacing: 865 mm × 865 mm (H × V) - Mould height: 500 – 1050 mm - Max. platen distance: 1770 mm - Location ring Ø: 160 mm - Location screw (MX): M20 - Core pulling: 2 sets Power Requirements: - Voltage: 380–400 V - Drive power: 166.4 kW - Heating wattage: 44 kW - Total power: 210.4 kW - Current requirement: 380 A Robot: ATM ES2000 Max. water heater temperature: 95 °C Machine dimens ...

Universal machine for elongating wheat doughs, mixed wheat and rye doughs (30% and 70% rye), rye doughs without a rolling table. Technical data: Weight range: 200-2000 gr Machine capacity: up to 2500 pcs/hour at 1000 gr Rounding length: 560 mm Dimensions (L x W x H): 5520x1100x1500 mm Weight, net: 880 kg Connection value: 1.5 KW Advantages: Gentle elongation due to the correct choice of the length of the elongation path, 3-stage dough processing: rolling, rolling, shaping, Low dough fatigue, Modern design, Quick and easy maintenance of the machine, stainless steel housing, Feeding hopper with adjustable opening.

Brand: Paoloni Type: T140 Motor power: 5 KW Milling mandrel : 30 mm Height adjustment milling spindle: 140 mm Speeds: 3000-4500-6000-9000 Spindle height adjustment: Handwheel adjustment with analog display Feed: HolzHerr 3 roll Option: Aigner integral stop

HOFMANN swivel spindle milling machine TFS 1200 Year of manufacture: 2004 S/N 127-01323 Manufacturer: Hofmann Bad Windsheim from a training company very good condition electric height and swivel adjustment manual height and swivel adjustment for fine adjustment analogue display for height adjustment, height adjustment 125mm Table size 1200 x 820mm and table extension 200 x 820mm Swivel range -5° to + 45 Spindle speed 3000/4000/5000/6000/8000/10000 rpm. Milling spindle D=30mm milling mandrel MK5 Engine 4.7 Kw / 6.3 hp Suction nozzle D=120 mm Side roller table with eccentric hold-down device and adjustable angle stop Height adjustable with handwheel CE mark Weight 1300 kg

Code: 0339 Brand: WEINIG Model: PROFIMAT 23/E - CE Standard Automatic 5-spindle moulding machine for the production of frames, furniture parts, windows, doors, moldings, broom handles, wooden toys, and various - CE Standard Features: Heavy-duty base made of solid cast iron Chainless cardan feed: precise, robust, and durable Special feed roller teeth that reduce the depth of entry into the wood Compact feed system Pneumatic pressure on the feed rollers DIGISET WEINIG for left and upper spindles: tool adjustment is performed directly via dual digital displays Technical data: Min/max working width 20/230 mm Max working height mm 120 Feed speed variator 5–24 mt/min Shaft diameter mm 40 Shaft speed rpm 6000 Feed roller diameter 140 mm Pre-planing table length 2000 mm Soundproofing and full protective coating Motorized vertical feed adjustment Side roller pressur ...

Weibert WJ-F10 Table milling machine new • New version: WJ-F10-1150 • Milling machine: swivel 90°-45° • Milling machine rpm 1400/3500/6000 and 8000 min. • Sliding table 1150mm (optional 1600mm) • Motor power: 400V 3 KW (4.0 HP) • WJ-600100 • Options at extra cost: • Telescope 900mm • Eccentric clamp • Milling motor 4 KW (5.5HP), S1 100% • Milling motor 5.5 KW (7.5 HP)S1 • Milling spindle 30mm • Eccentric clamp • Integral safety rails 500mm • Clockwise and counterclockwise rotation • Table extension right/left

SPECIFICATIONS: Pre-spindle machine inlet: 2000 mm Working width: 210 mm Working height: max. 120 mm Cardan shaft drive Drive shaft power: 2.2 kW I. Spindle: Bottom (4 kW) II. Spindle: Right (3 kW) III. Spindle: Left (4 kW) IV. Spindle: Right (5.5 kW) V. Spindle: Above (5.5 kW) VI. Spindle: Above (5.5 kW) VII. Spindle: Bottom (4 kW) With tools

Injection Unit Screw Diameter: Ø 50 Injection Volume: approx. 490 cm³ Injection Pressure: up to 1,800 bar Injection Rate: approx. 350 cm³/s Plasticizing Capacity: approx. 50 g/s (PS) Nozzle Contact Force: 65 kN Clamping Unit Clamping Force: 2,600 kN (260 t) Clamping System: ENGEL Victory tie-bar-less design Platen Size (H × V): approx. 1,000 × 950 mm Mould Opening Stroke: 600 mm Max. Daylight Opening: approx. 950 mm Min. Mould Height: 350 mm Ejector Stroke: 150 mm Ejector Force (fwd / back): 50 / 30 kN Drive & Control Drive Type: Hydraulic Hydraulic System Pressure: up to 160 bar Pump Motor Power: 22 kW Total Installed Power: approx. 30 kW Power Supply: 400 V / 50 Hz / 3-phase Control System: ENGEL CC300 touchscreen control Equipment / Features Clamping Concept: Tie-bar-less design for improved mould accessibility and com ...

Injection Unit Engine not working Screw Diameter: 65 Ø Injection Volume: approx. 1,025 cm³ Injection Pressure: up to 1,800 bar Injection Rate: approx. 450 cm³/s Plasticizing Capacity: approx. 80 g/s (PS) Nozzle Contact Force: 100 kN Clamping Unit Clamping Force: 5,000 kN (500 t) Clamping System: ENGEL Duo two-platen design Platen Size (H × V): approx. 1,300 × 1,200 mm Mould Opening Stroke: 800 mm Max. Daylight Opening: approx. 1,400 mm Min. Mould Height: 400 mm Ejector Stroke: 200 mm Ejector Force (fwd / back): 90 / 60 kN Drive & Control Drive Type: Servo-hydraulic (ecodrive inside) Hydraulic System Pressure: up to 160 bar Pump Motor Power: 37 kW Total Installed Power: approx. 55 kW Power Supply: 400 V / 50 Hz / 3-phase Control System: ENGEL CC300 touchscreen control Equipment / Features Clamping System: Two-platen desig ...

- Handwheel adjustment of spindle height/angle - Spindle angle displayed via viewing window, swivel range -4 to + 45° - Right-left rotation - double-sided table extension to 2,000 mm - Engine power 5 kW - Speed 3,000 / 4,500 / 6,000 / 9,000 / 12,000 rpm (manually adjustable) - Suction nozzle Ø 2 x 120 mm - Emergency stop switch) - Power: 380 V, 50 Hz, 3~, 10.8 A - with 4-roller feeder

Injection Unit Screw Diameter: Ø 70 Injection Volume: approx. 1,540 cm³ Injection Pressure: up to 1,800 bar Injection Rate: approx. 500 cm³/s Plasticizing Capacity: approx. 95 g/s (PS) Nozzle Contact Force: 120 kN Clamping Unit Clamping Force: 6,500 kN (650 t) Clamping System: ENGEL Duo two-platen design Platen Size (H × V): approx. 1,600 × 1,500 mm Mould Opening Stroke: 900 mm Max. Daylight Opening: approx. 1,600 mm Min. Mould Height: 450 mm Ejector Stroke: 250 mm Ejector Force (fwd / back): 110 / 70 kN Drive & Control Drive Type: Servo-hydraulic (ecodrive inside) Hydraulic System Pressure: up to 160 bar Pump Motor Power: 45 kW Total Installed Power: approx. 65 kW Power Supply: 400 V / 50 Hz / 3-phase Control System: ENGEL CC300 touchscreen control Equipment / Features Clamping System: Two-platen design for compact footp ...

SPECIFICATIONS: Planer: 2500 mm Machinable width: max. 210 mm Working height: max. 150 mm Cardan shaft drive Drive shaft power: 5.5 kW Spindle configuration: I. Spindle: Bottom (4 kW) II. Spindle: Right (4 kW) III. Spindle: Left (5.5 kW) IV. Spindle: Right (4 kW) V. Spindle: Top (4 kW) VI. Spindle: Bottom (4 kW) VII. Spindle: Universal spindle (5.5 kW) With tools.

Injection Unit Screw Diameter: Ø 55 Injection Volume: approx. 517 cm³ Injection Pressure: up to 2,000 bar Injection Rate: approx. 220 cm³/s Plasticizing Capacity: approx. 35 g/s (PS) Screw L/D Ratio: 22:1 Nozzle Contact Force: 60 kN Clamping Unit Clamping Force: 2,300 kN (230 t) Clamping System: Zhafir Zeres all-electric toggle system Platen Size (H × V): approx. 850 × 800 mm Mould Opening Stroke: 470 mm Max. Daylight Opening: approx. 940 mm Min. Mould Height: 220 mm Ejector Stroke: 150 mm Ejector Force (fwd / back): 50 / 30 kN Drive & Control Drive Type: All-electric servo drive Installed Power: 47 kW Full Load Current: 79 A Short Circuit Current: 25 kA Power Supply: 400 V / 50 Hz / 3-phase Control System: Zhafir SIGMATEK HMI touchscreen control Equipment / Features Drive Concept: Fully electric servo system for high p ...

Pastry forming machine, Fabr. Janssen, Type FM 126

Injection Unit Screw Diameter: Ø 50 Injection Volume: approx. 392 cm³ Injection Pressure: up to 2,100 bar Injection Rate: approx. 200 cm³/s Plasticizing Capacity: approx. 30 g/s (PS) Screw L/D Ratio: 22:1 Nozzle Contact Force: 50 kN Clamping Unit Clamping Force: 1,900 kN (190 t) Clamping System: Zhafir Zeres all-electric with servo-hydraulic auxiliaries Platen Size (H × V): approx. 770 × 720 mm Mould Opening Stroke: 450 mm Max. Daylight Opening: approx. 900 mm Min. Mould Height: 200 mm Ejector Stroke: 150 mm Ejector Force (fwd / back): 40 / 30 kN Drive & Control Drive Type: Hybrid electric / servo-hydraulic (Zeres series) Connected Load: 45 kW Full Load Current: 76 A Short Circuit Current: 25 kA Power Supply: 400 V / 50 Hz / 3-phase Control System: SIGMATEK CNC-based control with Zhafir HMI touchscreen Equipment / Features Dr ...

Injection Unit Screw Diameter: Ø 65 Injection Volume: approx. 1,075 cm³ Injection Pressure: up to 1,750 bar Injection Rate: approx. 400 cm³/s Plasticizing Capacity: approx. 85 g/s (PS) Nozzle Contact Force: 110 kN Clamping Unit Clamping Force: 5,500 kN (550 t) Clamping System: ENGEL Duo two-platen design Platen Size (H × V): approx. 1,350 × 1,300 mm Mould Opening Stroke: 850 mm Max. Daylight Opening: approx. 1,450 mm Min. Mould Height: 400 mm Ejector Stroke: 220 mm Ejector Force (fwd / back): 95 / 65 kN Drive & Control Drive Type: Hydraulic (pre-ecodrive generation) Hydraulic System Pressure: up to 160 bar Pump Motor Power: 45 kW Total Installed Power: approx. 65 kW Power Supply: 400 V / 50 Hz / 3-phase Control System: ENGEL EC88 digital control panel Equipment / Features Clamping System: Robust two-platen design for hi ...

Vacuum coating system with UV dryer/hardener Manufacturer: Giardina Year of construction: 1998 Paint shop Model: MCD/5 UV Dryer Model: SPC/12

Single-station machine for items up to 10 ltr. Extruder 6+0/20D. Single head, capped separator. Waste die-cutter. At call

Manufacturer | manufacturer: Hesta Machine Type | machine type: HM 501 Stations | stations: Single Station | Single station Year of construction | Built: 1993 Location | location: UES Clamping force | Clamping force: 40 kN Control Type | control system: Original Hesta Extruder | Extruder: 50/22D Extrusion Head | Extrusion Head: 2-fold head 100mm | Double head 100mm Mold dimensions mm | mold dimensions mm (A length / length x B Breite / width x C Tief/depth): Bottle Volume Max. | bottle volume max.: 2 L Screen Language | monitor language: German / English | German / English Delivery Time | Delivery time: 1 - 3 weeks | 1 - 3 weeks