bale presses used for sale

Manesty Drycota 900 23 Station Double Headed Tablet Press with Type D Tooling • This Double Headed Tablet Press is Mounted on a Common Chassis Plate and Driven via Line Shaft by a Common Drive • Twin Single Compression • Turrets Are Each Fitted With 23 Type D Stations • Upper Keyed Tooling • Removed Side Attached Operation Control Panel N°. of Stations: 23 Voltage: 400 VOLTS Frequency: 50 HERTZ Phase: 3

Machine cleaned by a specialist & functionally tested Properties: + Partial knife made of stainless steel + even division of the dough + excellent rounding of the dough pieces + ergonomic knife cleaning position (head can be swiveled to the side) + easy and quick adjustment of the effective chamber height STANDARD equipment: + 3 knitting plates included Technical data, according to manufacturer's specifications: Quantity: 30 pieces of dough Unit weight: 30 - 93 grams (depending on dough / product) Dough insert: 900 - 2,800 grams (depending on dough / product) Power: 0.55 kW Powers: 400V - 3Ph - 50Hz Fuse: 16A-CEE plug Dimensions: 63 x 59 x 134 cm (WxDxH) Working height: 81 cm Height with lever: 202 cm Net weight: 250 kg

Rotary tablet press SPT- TP500D with double-sided press; Brvyulnw 2 layered production; Touch screen, PLC Control Panel; HMI (Human Macshine Interface); SPT-TP 500D Number of stations (Max.) D=41 B=49 BB=59 1 Max tablet ejection (two-sided) T/h 270 000 360 000 420 000 Max tablet ejection 2 layer T/h 90 000 115 000 140 000 2 Max.Tab.Diameter Round mm 13 16 25 Form 14 19 25 3 Max tablet thickness mm 8.5 4 Max main pressing force t 10 6 Dimensions mm 1150 x 1550 x 1950

Machine Mechanics & electrics completely overhauled & repainted by an expert 6 months warranty Properties: + Stationary machine, very robust & stable construction + Machine is set in motion by switch-on lever, one-hand operation + with effective cut-off + Cleaning position to the rear with hand crank + even division of the dough, excellent rounding of the dough pieces + Partial knife / cutter head has been overhauled / recoated + Machine was completely disassembled, mechanically & electrically overhauled, repainted + Transmission parts run constantly in an oil bath + complete overhaul in our workshop, according to German quality standards + only high-quality original parts are installed + Machine was finally tested with dough by master baker Standard equipment: + incl. 3x knitting plate, new Special equipment, available at extra cost: + Chassis for Fortuna Automat ...

Roll press / dough dividing and warp knitting machine / Klievmaschine Machine Mechanics completely overhauled & repainted by the expert New installation of the entire electrical system, according to the latest standards 6 months warranty Properties: + Stationary machine, very robust & stable construction + Machine is set in motion by switch-on lever, one-hand operation + Cleaning position electric, to the rear, with switch + even division of the dough, excellent rounding of the dough pieces + equipped with active cut-off, for square dough pieces + Partial knife / cutter head has been overhauled / recoated + completely disassembled, mechanically overhauled, repainted + New installation of the entire electrical system, according to the latest standards + Transmission parts run constantly in an oil bath + complete overhaul in Babenhausen, according to German quality stand ...

Rotation tablet press SPT-TP 400 with high production capacity; Touch screen, PLC Control Panel; HMI (Human Macshine Interface); SPT-TP 400 Number of stations (Max.) D=30 B=36 BB=45 1 Max tablet ejection/hour T/h 125000 170 000 215 000 2 Max.Tab.Diameter Round mm 13 16 25 Mould mm 14 19 25 3 Max tablet thickness mm 8.5 4 Max main pressing force t 10 5 Max pre-press force t 2 Hqgonxsno 6 Dimensions mm 1000 x 1230 x 2000

ZM press Max ram adjustment: 400 mm Passage between uprights: 800 mm Max distance between table - ram: 500 mm

PONAR ŻYWIEC PHM 160 D hydraulic press manufactured in Poland in 1990 is used for machining metal and processing plastics (e.g. polofen or melamine) or rubber. The machine characterised by its high reliability, performs precise machining with a force of 160 tonnes in manual mode as well as in semi-automatic or automatic mode, thanks to its being equipped with time relays. The gantry press is also equipped with, among others, a hydraulic ejector with a force of 60 tonnes and two temperature controllers for the upper and lower parts of the heating plate. The offered machine was purchased from the university and has never worked during typical production. The total weight of the machine is 4000 kg. Technical parameters of the PONAR ŻYWIEC PHM 160 D press - maximum pressing force: 160 t (1600 kN) - ejector force: 60 t (600 kN) - working table surface (L x W): 800 x 800 mm - pressing ...

The small rotary tablet press SPT-TPL 200 (small scale production); Touch screen, PLC control platform; HMI system; Bczkcapdbh The machines comply with the requirements of the GMP guidelines and are CE certified; Number of stations (Max.) D=13 B=16 BB=19 1 Max tablet ejection/hour T/h 46 000 57 000 68 000 2 Max.Tab.Diameter Round mm 25 16 13 Shape mm 25 19 14 3 Max tablet thickness mm 8.5 4 Max main pressing force t 5 5 Max pre-press force t 1 6 Dimensions mm 600 x 1106 x 1705

used cabinet press Manufacturer: Maschinenfabrik Bermatingen GmbH & Co. Type: DIXI 30 S Year of construction: 2009 Serial No.: 109138 specifications: Pressing force: 30 t Filling opening: 1,200 x 670 mm (W x H) Height from the ground: approx. 940 mm Split egg filling opening: 1,070 x 260 mm Height from the ground: 1,310 mm Bale size: 1,200 x 800 x 800 - 1,100 mm Bale weight: up to 270 - 360 kg Drive power: 7.5 kW Cycle time: approx. 29 sec. Pressing time: approx. 14 sec. Binding: 4-fold - vertical with poly strap Machine dimensions: 1,600 x 1,300 x 3,170 mm (W x D x H) Machine weight: 2,180 kg Transport height: 2,240 mm (Subject to errors in the technical data)

Stainless steel pedestal for bread presses / dough-sharing machines suitable for all common bread presses massive construction resilient with 1 to easy lifting with the lift truck Stainless steel for optimal cleaning Dimensions: 735 x 640 x 170 mm, WxDxH Visit our large bakery machinery warehouse!

Press force: 300 t Stroke length: 200 mm Stroke speed: 20-60 1/min Shut height: 680 mm Ram adjustment: 200 mm Overall size: 2600x2000x4200 mm

used cabinet press Manufacturer: Maschinenfabrik Bermatingen GmbH & Co. Type: DIXI 30 S Year of construction: 2009 Serial No.: 109139 specifications: Pressing force: 30 t Filling opening: 1,200 x 670 mm (W x H) Height from the ground: approx. 940 mm Split egg filling opening: 1,070 x 260 mm Height from the ground: 1,310 mm Bale size: 1,200 x 800 x 800 - 1,100 mm Bale weight: up to 270 - 360 kg Drive power: 7.5 kW Cycle time: approx. 29 sec. Pressing time: approx. 14 sec. Binding: 4-fold - vertical with poly strap Machine dimensions: 1,600 x 1,300 x 3,170 mm (W x D x H) Machine weight: 2,180 kg Transport height: 2,240 mm (Subject to errors in the technical data)

(analogue of KB8344) Specification: Nominal force: 2500 ton Ram stroke: 190 mm Number of strokes in 1 minute: 20 Shut height: 800 mm Bolster plate-to-ram adjustable stroke: 15 Table size: 1250x1400 mm Weight 124.230T

Overall Size: 1400x1300x2300 mm Work space: 200x200x150 mm

Veneer press Leopida Format: 2300 x 1000 mm Plates with hot water heating L x W x H: 2300 x 1100 x 2000 mm Weight approx. 2000 kg Built in 1978 The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

I sell several machines, equipment here. spare parts, etc. for woodworking, Forklifts, work platforms as well as accessories and spare parts for forklifts and work platforms. Therefore, be sure to check out my other auctions Briquette press briquetting press chip press Pressing unit without control WEIMA TYPE: TH50 Briquette diameter approx. 50 mm Motor power hydraulics 5.5 KW They only bid on the briquette unit incl. hydraulic power unit. there is no control. I still have a control for briquette press with LOGO module. This can be purchased at an additional cost. The power unit could not be tested. Will be sold as it says here. ( See pictures ACTUAL - condition) Prior viewing is expressly desired, just leave phone no. by mail, then I will get back to you for a viewing appointment. Subject to prior sale, all information is subject to change. The ma ...

Baler Presto HPK 50 HS (HPK 750 H), year of manufacture 2013 Manafacture: Presto Type: HPK 50 HS (HPK 750 H) Year of construction: 2013 Hours: 3788 Propulsion: 30 KW Pressing force: 500 kN Filling opening: 1600 x 650 mm (LxW) Duct cross-section: 700 x 950 mm Filling volume, max. 1.06 m³ Cycle time: 20 s Binding: 4-fold Throughput capacity at 35 kg/cbm: 5.5 t/h 60 kg/cbm: 8.8 t/h 100 kg/cbm: 12.7 t/h Bale weight: up to 500 kg Machine dimensions: 8420 x 1900 x 2400 mm (LxWxH) Machine weight: approx. 12,000 kg Please note: All technical data refer to information provided by the manufacturer. We assume no liability for the information provided or any errors. The offer is subject to change, subject to prior sale and can be revoked at any time. Visits are possible by appointment. The sale against prepayment is ex works, without guarantee and guarantee.

Machine type: Eccentric press Manufacturer: GRÖTZINGER Model: 15 t Built: 1965 Condition: good Offer type: used machine Technical data: Pressure force: 15.0 t Extension: 120 mm Table: 460 x 255 mm Installation height: 250 mm Drive: 1.6 kW Remark: infinitely variable speed adjustment Weight: 750 kg The machine is in a good and ready-to-use condition and can be visited and demonstrated by us. We would be happy if our offer finds your interest.

• 120 tons total pressing force • Pressing area 3,000 x 1,350 mm • With patented, thermostable electric heating plates with automatic temperature control system • Connected load of the heating plates with economy circuit 10.6 kW • Connected load of the hydraulics 2.2 kW • in 6-cylinder version Ø 85 mm • Lockable main switch • Push-button control • Stop button • Safety ripcord, safety edge • Timer with automatic opening and acoustic signal • Stroke = opening 400 mm • Infinitely adjustable stroke limitation • 2-stage hydraulics with automatic pressure follow-up • Compact hydraulic power unit mounted maintenance-free in the oil tank • Teflon bronze guides in the cylinders • Hard chrome-plated steel pistons • Heavy rack and pinion compensation for synchronous table movement • fully open on four sides • Economy circuit installed as s ...

Dough part and actuator, Bread press Model: 4-30 NEW mature technology ... the original! Knife with simple cleaning position! Dough divider semi-automatic with 3 actuating plates Dough ring coated with easy click Sub range 40 to 120 grams/piece Division 30 in part Machine mobile DGUV V3 tested Connection 400V, 0.75 kW, 16A-CEE plug Dimensions: 600 x 700 x 1520/2200 mm, WxDxH NEW Machine with 2 years warranty

ERFURT PKZZ 315 double column press manufactured in 1984 in Germany is used for, among others, cutting, machining, bending and punching sheet metal and strip metal. Features such as the ability of extensive workpiece machining, a large work table and a 315-tonne operating slider make the crank press ideal for mass production of things such as washing machine parts, agricultural machinery or other types of vehicles. The ERFURT mechanical press is also distinguished by its high-quality welded steel construction, ensuring excellent stability during the production process. The machine uses a slider with a beam ejector, which is adjustable within a range of 400 mm via a motor reduction gear with overload protection. In order to increase the life of the tools and the quality of the parts produced, the 2500 mm long and 1400 mm wide work table has been equipped with hydropneumatic cushions.  ...

Baling press cardboard foil MF100 | 6 t pressing force The MF100 balers are ideal for pressing cardboard, paper, film, clothing and other materials. Volume reduction through compaction of up to 90%. The press is user-friendly with a large filling volume. The automatic bale ejector helps to remove the bales from the baler without any problems. Characteristics: Bale weight of up to 100kg Ideal for use with medium material volumes Fully automatic bale ejection Powerful cylinder for uniform material compaction Hold-down device to reduce material springback CE certified Made in Europe Specifications: Pressing force: 6 t Motor: 1.5 kW 13 Amp Power supply: 220-230 V (1 phase) Machine dimensions (H x W x D): 2371 x 1388 x 1046 mm Transport height: 1876 mm Machine weight: 632 kg Cycle time: 28 seconds Noise level: 65 decibels Bale: Ba ...

Overall size: 900x900x1800 mm Stroke length: 80 mm Weight: 702 kg The machine used for electric motor coal/carbon brush pressin

In the inlet - Baling press Strautmann, type BaleTainer, pressing force 60 t, year of construction 2014 Specifications: Manufacturer: Strautmann Umwelttechnik Type: BaleTainer Year of construction: 2014 Pressing force 60 t Total power 9.0 kW, 400 V Height filling opening 1370 mm Bale dimensions 1,100 x 1,100 x 800 mm (W x D x H), 3 discs Bale weight up to 400 kg (3 slices) Binding 4-fold vertically Machine dimensions with feed: 6,500 x 2,113 x 2,800 mm (L x W x H) Weight approx. 8,000 kg Materials: paper, cardboard, PET bottles, foil Please note: All technical data refer to information provided by the manufacturer. We assume no liability for the information provided or any errors. The offer is subject to change, subject to prior sale and can be revoked at any time. Visits are possible by appointment. The sale against prepayment is ex works, without  ...

spare parts - cook bolinders - Hydraulic cylinder PRESSING Hydraulic cylinder pressEN

Ortlinghaus coupling outer diameter 680 mm from stock as good as new

Veneer press - School press - Experimental press BÜRKLE U40 built 1979 Ges. Power: 6.25 kW Nominal operating current: 14.5 A Power per heating plate: 2,750 W Plate size: 120 x 80 cm Electric Aluminum Heating Plates max. temperature: 120° C Opening width: 40 cm 4 hydraulic cylinders each with a diameter of 70 mm Nominal surface pressure: 4 kp/cm² max. surface pressure at 75% surface design: 5.5 kp/cm² Operating pressure: 260 bar Circumferential safety ripcord (emergency stop) Automatic opening (automatic opening after the preset time has elapsed) Press frame in dismountable design Weight: 1,350 kg Machine dimensions (approx. dimensions): L 165 cm W 96 cm H 173 cm School machine - The machine comes from a school training center.

Crank press ZAMECH PKRR 400A built in 1974. Technical data : - pressure: 400 tons - clearance between stands: 1020 mm - ram stroke: 315 mm - number of strokes per minute: 20 - maximum distance of the slider from the table closed: 742.5 mm - slider adjustment: 250 mm - table dimensions: 1020 x 1050 mm - main engine power: 40 kW - main engine revolutions: 1500 1 / min. - weight of the press: 40 t

Key data: 63 t

EUROMET Y41-63T hydraulic press manufactured in 2007 is designed for machining metal sheets, sections and profiles. EUROMET Y41 63T hydraulic press has a monolithic structure resistant to any deformations, which, combined with the 63-ton press force, allows to achieve excellent precision and quality of machining both in medium and large series production. Technical parameters of EUROMET Y41-63T hydraulic press - maximum press force: 63 t - work table dimensions (L x W): 580 x 560 mm - piston rod speed (pressure): 10 mm/s - piston rod speed (return): 95 mm/s - piston rod speed (no load): 38 mm/s - piston rod stroke: 500 mm - maximum piston rod feed: 800 mm - power: 7.5 kW

Crank press HECKERT PKZ 400.1 built in 1980. Technical data : - maximum pressing force: 400 t - working path - lower position of the slider to the maximum pressing force: 21 mm - maximum drawing depth: 125 mm - pressing force using the maximum drawing depth: 160 Mp - idle speed of the slider: 18 min-1 - maximum number of switchings: 9 min-1 - ram stroke (min-max): 315 mm - slider adjustment: 200 mm - holding force of the drawing device at air pressure: 63 Mp, 5 kp / cm2 - force of the drawing device ejector at air pressure: 10 MP, 7 kp / cm2 - total weight: 38.5 t

a hydraulic single-stand drawing press Müller model CLZ.100.1.34, Y.O.M. 1994, good condition, with UVV, Siemens S7 screen control, throat gap 400 mm, installation height 800 mm, table surface 800 x 730 mm, stroke 600 mm, drawing cushion 40 to., drawing cushion stroke 200 mm.

No. 4105: 1 gebr. Hydraulic riypress Fabr. G + K, type SI 40/50, Bauj. 2000 Accessories: Table 500 x 400 mm Other: Pressure force max. 600 kN Impact stroke 150 mm Weight approx. 4500 kg

Vertical baler Strautmann PP 1207 Manufacturer: Strautmann Type: PP 1207 Year of construction: 2002 Pressing force: 58 t Total connected load: 4.5 kW Height filling opening: 1145 mm Filling opening: 600 x 1190 mm Press cycle: 37 sec. Bale size: max. 1180 x 700 x 800 mm Bale weight: up to 350 kg Dimensions: 1844 x 1067 x 2868 mm Weight: 2400 kg Materials: paper, cardboard, cardboard, foil, plastic, PET bottles, tin cans Please note: All technical data refer to information provided by the manufacturer. We assume no liability for the information provided or any errors. The offers are subject to change, subject to prior sale and can be revoked at any time. Visits are possible by appointment. The sale takes place from the location, without guarantee and guarantee. Our payment term is 100% prepayment.

Press capacity: max. 45 t Pull force: max. 45 t Counter force in pressing position: max. 17 t Stroke of the punch: 175 mm Filling height: max. 140 mm Deduction: max. 85 mm Compression distance: max. 55 mm Top pressing: max. 15 mm Stroke rate: 9 – 26 min.-1 Motor: 7,4 kW Approx: 3000x1200x1800 mm Net weight: about 5000 kg

Bookpress / twin plates / Hydraulic Splek Model IIB Year 1975 Size 280 x 440 mm Stack height 600 mm Pressure 3 tons Available Direct

Europress EP 6500 V5 H4, pressing force 120 t, year of construction 2009, drive power 75 kW, only 15,334 operating hours, overhauled Specifications: Manafacture: Europress Type 6500 V5 H4 Year of construction: 2009 Operating hours 15,334 hours, as of January Number of pressed bales 138,097 bales, as of January Pressing force main press 120 t Specific pressing force 142 kg/cm² Dimensions insertion chute 1,650 x 1,100 mm Filling volume 3 m³ Filling volume / pressing cycle 1.58 m³ Bale dimensions 730 x 1,100 Length variable Drive power 75 kW (1 x 30 kW + 1 x 45 kW, individually switchable) Total connected load 83 kW Current consumption 150 A Binding 5-fold vertical, 4-fold horizontal, fully automatic Bale weights 450 to 900 kg, depending on bale length and material Hydraulic oil tank volume 1,200 L PLC control (manuf., type) Siemens S7-200 Control Panel (Manufactur ...

SPK KB 2132 eccentric press was manufactured in the USSR in 1980. Operating with a force of 160 tonnes, the press of almost indestructible design offers the highest quality and precision during the most demanding workpiece machining. The machine’s equipment includes among others a pneumatic clutch, a large-area slider performing up to 71 strokes per minute, central lubrication and manual control. The total weight of the press is 13200 kg. Technical data of the SPK KB 2132 press - maximum press force: 160 t - work table dimensions (L x W): 1000 x 700 mm - maximum slider stroke: 160 mm - minimum slider stroke: 25 mm - slider dimensions (L x W): 580 x 460 mm - slider adjustment range: 120 mm - slider stroke rate: 71/min - intermediate plate thickness: 110 mm - distance between work table and slider (slider in lower position, largest stroke, connector unscrewed): 480 mm - bore ...

Table top height: 910 mm Table top size: 700 x 380 mm Max drilling depth: 145 mm Max long hole length: 240 mm Height adjustment distance 135 mm Engine power: 1.5 kW Voltage: 400 V / 50 Hz Speed: 3,000 rpm Net weight: approx. 200 kg Suction nozzle: 100 mm Dm Dowel drilling device: Pitch 16, 22, 25, 32 mm with precision grid roller Driving equipment: Yes Frame stop 90°: pluggable Two-jaw chuck: up to 20 mm clamping range Hand eccentric tensioner: 1 piece 1 Lever control: Yes Measuring clock in handwheel: Yes Miter stop: Yes, double angle adjustment stop from 22.5° to 75° infinitely adjustable

2886: 1 gebr. Difiting press 200 kN Fabr. REIS, type TUS 60 OK 20, Bauj. 1991 with hydr. Control Arb.-Ber.: Stroke approx. 700 mm, drive power: 7.5 kW Accessories: extendable table 670 x 570 mm, swing-out top plate 670 x 570 mm, Mounting height 740 mm Other: Passage between the columns 620 mm, Space requirement L/W/H 1870 x 1620 x 3000 mm, Weight approx. 3.5 tons. very good condition

automatic baler Manafacture: UNOTECH Type: UPAMAT 100 V 5 Year of construction: 2014 specifications: Cutting force: 1,000 / 315 KN / bar Specific pressing pressure: 12.12 kg/cm² Filling opening 2,000 x 1,020 mm Duct format: 750 x 1,100 mm (H x W) Bale weight: 500 - 800 kg (depending on material and bale length) Binding: 5-fold vertical Drive power: 1 x 75 kW Nominal current consumption: 175 A Connection fuse max. 200 A Pump: Internal gear pump Noise emission: 82 - 85 dB/A Machine weight: 32,000 kg Control: Siemens S7 - IM-151 Output: approx. 340 m²/hour under operating conditions Throughput: at 30 kg/m³ bulk density approx. 10.0 t/h at 50 kg/m³ bulk density approx. 16.0 t/h at 100 kg/m³ bulk density approx. 32.0 t/h Equipped with: Press box planked with HARDOX central lubrication point Large-digit display  ...

No. 3421: 1 gebr. Tool press Fabr. SCHÖN, type SH-PZ 250, Bauj. 1979 Arb.-Ber.: Pressure power 250 to mm, drive power: .22 kW Accessories: Table 500 x 500 Other: Single stroke 2-hand Single stroke foot switch automatic continuous running set up and tap

2 column hydraulic press #5232 Press force: 200 t upper stroke: 500 mm lower stroke: 200 mm overall dimension: 1800x2200x3700 mm Power: 10 PS Weight: 8.4 t

For sale is a functioning pellet production line including controls. The plant is suitable for pelletizing agricultural raw materials (straw/hay/alfalfa etc.) and has an output of 1000-1600 kg/hour depending on the material. The complete system has approx. 800 operating hours The production line is composed of: cjffolp2bh Byfo0wxd Bale breaker 37 KW + bale conveyor table 10m and Hammer mill 75 KW Zyklon + Rotary Valve + Buffer Tank Scheuch dust filter house with control system and a capacity of 20,000m3/h including discharge for big bags, 2 Koller ring matrices pellet mill 110 KW with aut. Central lubrication. In the associated conditioner, the moisture content of the material is automatically controlled by means of a dosing pump and mist nozzle as well as a microwave sensor from the Envea brand. Pellet cooler with level sensors and automatic emptying. Vibrating scr ...

Filter press plate filter ultrafiltration plate filter used Manufacturer: Rhone Poulenc Type: UFP 70 Max working pressure: 4.5 bar/64 psi Torque: 8 mxkg 6x24 plates approx. 2000 x 600 H 1700 mm Changes and errors in the technical data, Information and prices as well as intermediate sale reserved.

PressOne P1S-8 is a press-fit machine from Finland that is powered by a ball-circuit spindle with servo motor. This gives you the best of both worlds. Power, speed and accuracy. No oil means no leakage problems, no rush of oil changes and no filtration problems. Only pure power, accuracy and speed! Specifications: P1S-8 Main press technology: ball-circuit spindle with AC servo drive Maximum pressing force: 80 kN Repeatability of force adjustment: ± 1% Maximum opening/approach speed: 120 mm / s Pressing speed: max 10 mm / s Extension: 620 mm Stroke length: 210 mm Faster range: M2 - M10 Servo motor: 0.6 kW Control: P1S TC12 Touchscreen 12" Tool connection: Type Haeger, 4-fold lower rotary base The maximum approach speed requires the "Fast Approach Speed" option. Control features of the P1S TC12: - Programmable pressing force - Programmable lifting opening - Progra ...

Code: 0578 Brand: SORMEC 2000 - ITALY Model: 10000 - Norme CE Automatic cold press for panels, polyurethane foam, industrial shed doors, perimeter walls, foamed panels, insulation panels, laminates and various - CE standard Technical data: Working dimensions mm 10000 x 1500 Workpiece passage mm 2000 Opening mm 1000 Height of roller table mm 500 Motorised roller conveyor for workpiece feed with possibility of forward/backward movement N° 18 pistons diameter mm 70 N° 2 hydraulic power unit Pistons opening/closing choiceor Pressing timer Safety protection nets Power Kw 10,3 Compressed air 7 bar Overall dimensions: mm 10500 x 2300 x 3300 h Weight kg 19000

Plate press Filter press Chamber filter press Industrial wastewater technology -used- Manufacturer: FAZZINI Type: F500 Operating pressure 15 bar Plate size 500 x 500 mm 20 plates with hydraulic unit 1.5 kW and piston pump 0.75 kW Dimensions: approx. 2400 x 750 x 1600 mm All items are checked for function before delivery, if technically possible !

PressOne P1S-10 is a press-fit machine from Finland that is powered by a ball-circuit spindle with servo motor. This gives you the best of both worlds. Power, speed and accuracy. No oil means no leakage problems, no rush of oil changes and no filtration problems. Only pure power, accuracy and speed! Specifications: P1S-10 Main press technology: ball-circuit spindle with AC servo drive Maximum pressing force: 100 kN Repeatability of force adjustment: ± 1% Maximum opening/approach speed: 120 mm / s Pressing speed: max 10 mm / s Extension: 620 mm Stroke length: 210 mm Faster range: M2 - M10 Servo motor: 0.6 kW Control: P1S TC12 Touchscreen 12" Tool connection: Type Haeger, 4-fold lower rotary base The maximum approach speed requires the "Fast Approach Speed" option. Control features of the P1S TC12: - Programmable pressing force - Programmable lifting opening - P ...

N° 0214: 1 gebr. Hydraulic quick-stroke two-stand press Fabr. SMG, Type DS 63, Bauj. 1984 with pressing force 630 kN, retraction force 51 kN Arb.-Ber.: Table area 660 x 460 mm, drive power: 15 kW Accessories: The press was upgraded to UVV 11.064 VBG 7n5.2 in 1991. Other: Light width between the stands 680 mm, max. distance between table top and pestle 385 mm, ejector force 15 kN largest pestle stroke 150 mm.