Fridge and freezer Capacity: 340/82 L Voltage: AC 230/240V Frequency: 50Hz Ampere: 2.5/2.4 A Power Consumption: 350/365W heating: 159W Refrigerant: R-134a: R-407D Load: 80: 113g, Weight (kg): 126, Dimensions (mm): 810x610 H1820, Elec: 230/240V 50Hz 2.5/2.4A, Volume (L): 340/82 ...

• more information

Manafacture: SANYO Type: MDFU-442 Capacity: 426 l Refrigerator compartment dimensions: 800 x 900 x 1800 mm Refrigerant: R-134a Weight: 240 kg  ...

• more information

PLC, PC, control, position controller, Hitachi Seiki, HC400 -The PC comes: from a Hitachi Seiki HC400 machining center -Manufacturer: Sanyo Denki -PC type: APC-9-203-1 -Dimensions: 300/150/H160 mm -Weight: 3.6 kg ...

• more information

Product number: 2837 Type: MLS-3020 Serial number: 4Z0185 Chamber: Ø 300 x 670 mm, 48 litres Sterilization temperature: 105 - 121 °C Pressure gauge range: 0 - 0.3 MPa Power: 230VAC, 50Hz, 2kW Dimensions: 440 x 550 x 1050 mm Weight: 69 kg  ...

• more information

Standing seam metal roof machine F3 Standing seam metal roof machine F3 with length measuring device was designed by our company to produce standing seam roofing panels for the installation of roofs and facades of various buildings and structures. Sheet metal blanks are passed through the forming rolls of the machine to get the desired shape of the standing seam panel. This method of production allows you to produce panels with a speed of about 10 meters per minute and fit any roofing companies. The machine is equipped with an easy width adjustment system, so it takes just a few minutes to readjust it from rolling one width to another. The F3 machine can work with panels from 200 to  ...

Te Coop: Vega sensor circuit signal conditioning instrument gate 636ex PTB ex-96.D. 2068  ...

• more information

Manufacturer: Paul Troester Maschinenfabrik/Hannover Year of construction: 1978, machine was in operation until the end of 2015 Screw diameter: 150 mm Length: 16 D (approx. 2,400 mm) Screw speed: 2.5-25 / 4 - 40 U/Min. Centre height of the extruder: 1,100 mm Type of gearbox 3 TH 990 K / 2s, 2 speeds. Gear ratio: = i1 16.5: 1 i2 = 26.4: 1 Maximum gearbox output torque: 45,000 nm Maximum permissible injection pressure: 350 bar without limitation through the extrusion head. The extruder will be overhauled and designed/changed according to customer's specification. Below pictures 1-4 show an extruder overhauled by us.

Used rubber extruder make Troester, type GSV 60/k-12-18D-m.S., Execution as desired, with or without vacuum Built in 1991, machine was in operation until the beginning of 2010 Feed roller Kpl. new drive with flat gear motor Screw speed max. 62 rpm. Engine power 22 kW Control with PLC and temperature control new on request Extruder similar to attached photos.

Machine number: 3728-87 Grinding length 2000 mm (Roll grinding machine)  ...

• more information

screw ø:: 90 mm screw length:: 20D screw speedl:: 0 - 60 U/min Condition: NEW, Specification: Rubber vacuum extruder - with warranty - Screw diameter: 90 mm - Screw length: L = 20 D (approx. 1,800 mm conveying length) - Screw speed: 0 - 60 rpm - Centre height of extruder: approx. 1,125 mm incl. base frame - Max. permissible injection pressure: 500 bar - with feed roller - Extruder water-tempered - Extruder base frame as welded construction, to accommodate the extruder with drive motor, the temperature control, the vacuum pump - Funnel piece with intermediate flange: two tempering zones approx. 4D = 480 mm - Vacuum cylinder: three  ...