Fabbricante:
(Categoria: 307)
roll diameter: 700 mmroll length: 2200 mmrolls drilled: Kernbohrung Nip adjustment: hyraulisch 0total power requirement: 160 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
screw ø:: 120 mmscrew length:: 17D screw speedl:: 42 U/mindrive power:: 138 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
diametro rotolo: 250 mm lunghezza rotolo: 500 mmrotoli forati: Kernbohrung nip regolazione: mechanisch drive potenza:: kW
machine measurements: 3.000 mmmachine weight: -- kgpower capacity: 90 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll diameter: 350 mmroll length: 700 mmrolls drilled: peripher Nip adjustment: hydraulisch 0total power requirement: 2x 15 kWCondition: new, with CE mark,Specification: Two Roll Mill 350 x 700 mm - new- cylinder diameter: 350 mm- cylinder length: 700 mm- cylinder boring: peripherally drilled- cylinder bearings: with grease lubrication- 2 cylindera chromed- nip admustment: hydraulically- new hydraulic unit- tipper guiding plates of nylon-polyethylen-material- stainless steel tray- bi-directional bars- AC brake motors: 2 pcs, each 15 kW, 400 V, 50 Hz- bevel gearboxes of transmission: 2 pcs- painting: with RAL colours acc. to customer’s specification- complete machine protection with stainless steel carters- new electric cabinet- new electrical system- new machine on-board system- new control panel Touchpanel 7- PLC system: 1 piece, brand S ...
chamber volume: 80 literuseable volume: -- literfriction: -- motor drive power: 390 kWCondition: used - overhauled - with warrantySpecification: Internal mixer used- Capacity: about 80 lts- Rotors model: tangential type with 3 wings- Command gearbox: semi-unidrive type- Max speed rotors: about 60 rpm- Closing system: drop-door type- Hydraulic unit for drop-door system- Pneumatic hopper for loading material- DC engine: 390 kW - 1500 rpm - 440 V- New electric cabinet with driving system for variable speed of rotors- N.1 new electric panel- New on board electric system on the machine- Safety devices in according to standard rules- Manual of use and maintenance in English language and CE marking- Reconditioned and guaranteed machine in according to standard rules- Warranty: 1 yearThe data for this ad was created with ModulMWS - the software solution ...
cross-section width:: -- mmcross-section heigth:: -- mmfeed:: -- mmspeed of feed:: 0,4 - 20 m/minThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cross-section width:: 85 mmcross-section heigth:: 25 - 40 mmfeed:: 1 - 999,999,9 mmspeed of feed:: 60 m/mincuts max.:: 100 - 120 Schnitte/mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
screw ø:: für Extruder 90 mmscrew length:: -- screw speedl:: -- U/mindrive power:: 13,6 kWCondition: little used, as good as newSpecification: gear pump ZP 75/50 for extruder size 90- SEW helical gear units: R 97- Siemens direct current motor: 1 GG5 118- Drive power: 13.6 kW, 57 A- curved tooth coupling- With clamp for the head connection,- Clamping flange for extruder and head connection,- Base plate with linear guide rails,- Tooth shaft diameter: 75 mm- tooth width: 50 mm- helical gearing, hardened steel bearings, right-hand drive- without controlThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll diameter: 400 mmroll length: 1100 mmrolls drilled: Kernbohrung Nip adjustment: hydraulisch total power requirement: 2x 30 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cross-section width:: 5 Schläuche 3-5 mmcross-section heigth:: 3 - 20 mmfeed:: 1,5 - 50 mmCondition: used, very good condition only approx. 1 year in productionSpecification: circular knife cutting machine for slices and rings- small cutting machine with high-speed rotating circular knife- feed and knife movement, pneumatic- Tube or strand diameter min.: 3 mm- Tube or strand diameter min.: 20 mm- Feed (ring or strand length): 1.5 - 50 mm- Output depending on material max.: 60 strokes/min- Optionally, the following can be cut 5 tubes or strands: diameter 3 mm to 5 mm 4 tubes or strands: diameter 5 mm to 7 mm 3 hoses or strands: diameter 7 mm to 12 mm 2 hoses or strands: diameter 12 mm to 15 mm 1 hose or string: diameter 15 mm to 20 mm- Power requir ...
clamping force: 450 kNinjection volume: 135 cm³screw diameter: 35 mmplaten size: 600 x 400 mmCondition: used,Specification: C-frame injection moulding machine for TPE - usedclamping unit:- clamping force: 450 kN- heating platen size: 600 x 400 mm- sliding table: yes- Clamping direction: from below- Ejector / lifter: Up + LoInjection unit:- Injection volume max.: 135 cm³- Screw diameter: 35 mm- Connected load: 3x 400 V, 50 Hz- Weight approx.: 5,500 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Press force max.:: 1.000 kNheating plates:: 500 x 500 mmelectrically heated:: °Cheating power:: kWpiston stroke:: ca. 500 mmno. of stages:: The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
0: 200 °CTorque: - 0Dimensions (HxWxD): 680 x 1320 x 760 mmweight: 177 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll surface width: 450 mmroll diam. toproll: 203 mmroll diam. bottom roll: 203 mmoutput: 8,8 kwThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll diameter: 400 mmroll length: 1000 mmrolls drilled: peripher Nip adjustment: hydraulisch total power requirement: 2x 30 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Farrel Twin Screw / Rollerdie Estrusore completo disponibile con motore e inverter Descrizione allegata!
disponibile Troester Triplex Extruder Macchina superiore QSM 90x 16D Macchina centrale 200W x 6D Sotto macchina QSM 150 x 16D Testa MW500 Descrizione allegata!
Key data: 70
Estrusore in gomma a vite singola con rullo di alimentazione e degassamento in viti 70mm e una lunghezza di processo di 22.D - con vite di entagling a due velocità a temperatura controllata - Cilindro di degassamento con dispositivo per degassamento statico e/o sottovuoto del materiale - una pompa a blocchi per vuoto - due unità di controllo della temperatura dell'acqua con capacità di riscaldamento di 9 kW ciascuna, - una macchina Siemens SPS S7 con pannello di controllo Siemens KTP1200 HMI - un alimentatore a rulli di alimentazione azionato direttamente per strisce grezze in gomma, un sistema di irrigidimento imbuto-materiale con Monitoraggio delle strisce - corpo di base temperabile per porta utensili e v.m
Calender da laboratorio 4-Roll Inch invertitoLinch Descrizione allegata!
Berstorff Rotocure AUMA 20-S Dia a tamburo: 2000mm Larghezza del tamburo: 2600mm Cintura d'acciaio Sandvic Descrizione allegata!
Nastro mesh per AUMA / Rotocure nuovo e inutilizzato Lunghezza: 14100mm Larghezza: 2250mm
Scala di pesatura Carbon Black 400l Descrizione allegata!
Macchina per il test dei pneumatici - Bilanciamento statico per pneumatici passeggeri. in condizioni di lavoro! Dimensioni del pneumatico da 15inch a 20inch Certificato Ce Lay-Out disponibile - sarà inviato su richiesta! Maggiori dettagli vedi la descrizione allegata!
con 15 carte - Rack S5 187U con 10 schede di estensione. Ambito di fornitura mostrato nell'immagine.
MEB Maschinenhandel GmbH
