We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
usato
clamping force: 350 kNinjection volume: 59 cm³screw diameter: 25 mmplaten size: 400 x 400 mmCondition: used,Specification: injection moulding machine for rubber - used International size: 350-90 clamping unit:- clamping force: 350 kN- clamping platen size: 400 x 400 mm- Clear distance between tie bars: 270 x 270 mm- Mould installation height min.: 225 mm- Distance between clamping platens: max. 550 mm- Opening stroke max.: 325 mm- Ejector stroke: 125 mmInjection unit:- Screw diameter: 25 mm x 20D- Injection volume max.: 49 cm³- Injection part weight: 59 g/hp- Max. injection pressure: 1,860 bar- Screw circumferential speed: 37 m/min- Cylinder heating: 4x 900 W- Nozzle heating: ...
usato
clamping force: 1.300 kNinjection volume: 230 cm³screw diameter: 45 mmplaten size: 685 x 685 mmCondition: used,Specification: injection moulding machine for TPE - usedincluding Koch dosing unitclamping unit:- clamping force: 1.300 kN- heating platen size: 685 x 685 mm- Clear distance between tie bars: 470 x 470 mm- Mould installation height min.: 250 mm- Distance between platens max.: 900 mm- Opening stroke max.: 650 mm- Ejector stroke: 225 mmInjection unit:- Screw diameter: 45 mm x 18D- Injection volume max.: 230 cm³- Injection part weight: 210 g/hp- Max. injection pressure: 1,670 bar- Screw circumferential speed: 75 m/min- Cylinder heating: 4x 2,200 W- Nozzle heating: 600 W- Connection value: 3x 400 V, 50 Hz- Electrica ...
usato
clamping force: 350 kNinjection volume: 58,5 cm³screw diameter: 28 mmplaten size: 260 x 254 mmCondition: used,Specification: injection moulding machine for TPE - usedclamping unit:- clamping unit: vertical- clamping force: 350 kN- opening stroke max.: 300 mm- platen distance max.: 500 mm- Mould installation height min.: 200 mm- Clear width between tie bars: 260 x 254 mm- Ejector stroke max.: 80 mm- Clamping unit: VV- Lift of protective bonnet: 500 mmInjection unit:- Screw diameter: 28 mm- Screw L/D ratio: 18.6- Screw stroke max.: 95 mm- Injection volume max.: 58.5 cm³- Injection pressure: 1577 bar- Plasticising flow: 8.6 g/s- Injection flow: 85.5 g/s- Connected load: 3x 400 V, 50 Hz- Max. heating power: 5.8 kW- Drive power: 7,4 kW- Total power: ...
usato
clamping force: 11000 kNinjection volume: 12500 cm³screw diameter: -- mmplaten size: -- mmCondition: used,Specification: injection moulding machine for rubber - used, in very good condition machine was serviced annually by manufacturerclamping unit:- Euromap (size): 11000-25600- clamping force: 11.000 kN- size of heating platens L/W/H: -- x -- x mmInjection unit:- Injection volume max.: 12,500 cm³- Injection pressure: 2050 bar- Dosing force: 118 kN- Control: Siemens S7- Connected load: 3x 400 V, 50 Hz, N- Total current: 276 A- Back-up fuse: 300 A- Pump drive: 277 bar- Driving power: 45 kW- Weight approx.: 43.8 tOperating hours approx.: 33,130 hoursThe data for this ad was created with ModulMWS - t ...
usato
clamping force: 2700 kNinjection volume: 3300 cm³screw diameter: -- mmplaten size: 780 x 670 mmCondition: used,Specification: vertical injection moulding machine for rubber NR, EPDM, SBR, NBR, CR, etc. - used, in very good condition 6 months in useclamping unit:- Euromap (size): 2700-7200- Clamping force: 2,700 kN- Heating platen size L/W/H: 780 x 670 mm- Distance between upper and lower platen: 970 mm- Stroke min.: 420 mm- Stroke: 550 mmInjection unit:- Injection volume max.: 3,300 cm³- Injection pressure: 2,180 bar- Nozzle contact force: 80 kN- Connected load: 3x 400 V, 50 Hz, N- Back-up fuse: 125 A- Pump drive: 265 bar- Drive power: 22 kW- Pump speed: 66 rpm- ...
usato
clamping force: 2700 kNinjection volume: 3300 cm³screw diameter: -- mmplaten size: 780 x 670 mmCondition: used,Specification: vertical injection moulding machine for rubber NR, EPDM, SBR, NBR, CR, etc. - used, in very good condition almost unused!clamping unit:- Euromap (size): 2700-7200- Clamping force: 2,700 kN- Heating platen size L/W/H: 780 x 670 mm- Distance between upper and lower platen: 970 mm- Stroke min.: 420 mm- Stroke: 550 mmInjection unit:- Injection volume max.: 3,300 cm³- Injection pressure: 2,180 bar- Nozzle contact force: 80 kN- Connected load: 3x 400 V, 50 Hz, N- Back-up fuse: 125 A- Pump drive: 265 bar- Drive power: 22 kW- Pump speed: 66 rpm- C ...
usato
Pressa a iniezione di gomma DESMA da 400 tonnellate -Modello : SIGMA 4000
usato
clamping force: 250 kNinjection volume: 49 cm³screw diameter: 25 mmplaten size: 300 x 300 mmCondition: used,specification: C-frame injection moulding machine - usedclamping unit:- clamping force: 250 kN- heating platen size: 300 x 300 mm- clamping/opening stroke: 330 mm- Closing direction: from below- Lateral ejector: yes- Ejector stroke/force: 115 mm / 12 kNInjection unit:- Injection volume max.: 49 cm³- Screw diameter: 25 mm- Screw length: 16- Screw speed max.: 250 rpm- Injection: from above- Voltage: 3x 400 V, 50 Hz, N, PE- Connected load: 55 kW/92 A- Weight approx.: 3,500 kgVarious accessories are also available:- Injection unit (25 screw)- 2 heating plates- Funnel and various small partsThe data for this ad was created with ModulMWS - ...
usato
clamping force: 450 kNinjection volume: 135 cm³screw diameter: 35 mmplaten size: 600 x 400 mmCondition: used,Specification: C-frame injection moulding machine for TPE - usedclamping unit:- clamping force: 450 kN- heating platen size: 600 x 400 mm- sliding table: yes- Clamping direction: from below- Ejector / lifter: Up + LoInjection unit:- Injection volume max.: 135 cm³- Screw diameter: 35 mm- Connected load: 3x 400 V, 50 Hz- Weight approx.: 5,500 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
usato
clamping force: 450 kNinjection volume: 99 cm³screw diameter: 30 mmplaten size: 860 x 320 mmclosing stroke: 406 mmCondition: used,Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083Clamping unit:- Clamping force: 450 kN- Opening travel: 406 mm- Heating plate size: 860 x 320 mm- Mould height min.: 264 mm- Max. plate spacing: 464 mm- Ejector stroke: 20 mm- Ejector force: 20 kNInjection unit:- Screw diameter: 30 mm- Screw length L/D: 16- Dosing stroke: 140 mm- Stroke volume max.: 99 cm³- Max. spray weight: 114 g- Screw speed: 20 - 300 rpm- Injection flow: 106 cm³/s- Injection flow increased: 71 cm³/s- Special injection pressure: 1451 bar- Spec. injection pressure increased: 2205 bar- Nozzle path: ...
usato
clamping force: 450 kNinjection volume: 99 cm³screw diameter: 30 mmplaten size: 860 x 320 mmclosing stroke: 406 mmCondition: used,Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083Clamping unit:- Clamping force: 450 kN- Opening travel: 406 mm- Heating plate size: 860 x 320 mm- Mould height min.: 264 mm- Max. plate spacing: 464 mm- Ejector stroke: 20 mm- Ejector force: 20 kNInjection unit:- Screw diameter: 30 mm- Screw length L/D: 17- Dosing stroke: 140 mm- Stroke volume max.: 99 cm³- Max. spray weight: 114 g- Screw speed: 20 - 300 rpm- Injection flow: 106 cm³/s- Injection flow increased: 71 cm³/s- Special injection pressure: 1450 bar- Spec. injection pressure increased: 2210 bar- Nozzle path: ...
usato
clamping force: 800 kNinjection volume: 78 cm³screw diameter: 25 mmplaten size: 570 x 552 mmCondition: used,Specification: injection moulding machine for LSR - used Nr. 13EN08clamping unit:- clamping force: 800 kN- size of heating platen: 570 x 552 mm- Between tie bars horizontally: 405 mm- Between tie bars vertically: 345 mm- Opening stroke: 310 mm- Ejector force: 25.4 kN- Ejector stroke: 100 mm- Mould installation height max.: 530 mm- Mould installation height min.: 250 mm- Bar diameter: 60 mm- Control: CC 90-A0Injection unit:- Injection volume max.: 78 cm³- Injection weight max.: 90 g- Screw diameter: 25 mm- Metering stroke: 160 mm- Screw speed max.: 20 - 400 rpm- Injection flow: 87 g/sec- Injection flow (increased): 64 g/sec- Sp ...
usato
clamping force: 800 kNinjection volume: 154 cm³screw diameter: 35 mmplaten size: 570 x 552 mmCondition: used,Specification: injection moulding machine for LSR - used Nr. 13EN12 clamping unit:- clamping force: 800 kN- size of heating platen: 570 x 552 mm- Between tie bars horizontally: 405 mm- Between tie bars vertically: 345 mm- Opening stroke: 310 mm- Ejector force: 25.4 kN- Ejector stroke: 100 mm- Mould installation height max.: 530 mm- Mould installation height min.: 250 mm- Bar diameter: 60 mmInjection unit:- Injection volume max.: 154 cm³- Injection weight max.: 156 g- Screw diameter: 35 mm- Metering stroke: 160 mm- Screw speed max.: 20 - 320 rpm- Delivery flow: 35 g/sec- Injection flow: 148 g/sec- Injection flow ...
usato
Macchina ad iniezione HUSKY Tipo H400 400 tonnellate Pressione idraulica 180 BAR max Peso 18.143 kg Marchio CE Anno: 2003
usato
Pressa ad iniezione Klockner Desma 100ton Modello:D968.100.Z0 Dimensioni piastra: 400mm di profondità x 500mm di larghezza Volume corsa 350cm3 Forza di chiusura 1000kN Pressione di iniezione 2380 bar Tensione 3x 400 50Hz Anno 1998
usato
LWB Steinl Pressa per stampaggio a iniezione / vulcanizzazione Modello: VCE-B Forza di chiusura 2500kN Volume di iniezione 1000 cm3 Aria compressa 6 bar 75 kW Olio idraulico 40/45 cst Dimensioni modello 760 x 630mm Touch screen LWB Flex Qtà 1 Tool Kemp modello TT-188 (anno 2019) canale caldo. Peso 12850 kg
usato
Macchina per stampaggio a iniezione LWB Steinl Modello VCE-T-TPE-EPDM Capacità 100 ton Controllo touch screen ECO
usato
LWB Steinl Pressa per stampaggio a iniezione / vulcanizzazione Modello: VCEFE Forza di chiusura 2500kN Volume di iniezione 1000 cm3 Aria compressa 6 bar 76 kW Olio idraulico 46/40 cst Dimensioni modello 760 x 630mm Touch screen LWB Flex Qty 2 Strumento Kemp modello TT-188 Anno 2013 Peso 13500 kg
usato
LWB Steinl Pressa per stampaggio a iniezione / vulcanizzazione Modello: VCEFE-B Forza di chiusura 2500kN Volume di iniezione 1000 cm3 Aria compressa 6 bar 76 kW Olio idraulico 46/40 cst Dimensioni modello 760 x 630mm Touch screen LWB Flex Qty 2 Strumento Kemp modello TT-188 Peso 13500 kg
usato
Pressa ad iniezione Maplan Modello: MTF400/80C 80 Tonnellata Distanza di sicurezza 162mm Tempo di rodaggio 81ms Follow-up 5mm Dimensioni del modello 510mm x 410mm Controllo touch screen
usato
Key data: 1500 kN, 750 cm³
Pannelli 510x400 mm Forza di chiusura 150 t volume massimo iniettato 750 cm³ larghezza libera 440 mm
usato
Macchina per stampaggio a iniezione Rep B46 Dimensioni delle piastre 430x430mm Unità di iniezione volume corto 670cm3 Pressione di iniezione 1690 bar Forza di iniezione 331kN
usato
clamping force: 1.013 kNinjection volume: 400 cm³screw diameter: 25 mmplaten size: 335 x 400 mmCondition: used,Specification: injection moulding machine for rubber - usedclamping unit:- clamping unit: vertical- clamping force: 1.013 kN- size of heating platen: 335 x 400 mm (standard) core turning unit Injection unit:- screw diameter: 25 mm- Barrel diameter: 51 mm- Injection volume max.: 400 cm³- Injection pressure: 1,500 bar- Connection value: 3x 400 V, 50 Hz 42A fuse protection (incl. periphery)- Electrical power: 29,1 kVA- Control: G8 Control- Hydraulics: 250 bar (tank 200 litres)- Further connections: Cooling water inlet/outletDimensions L/W/H approx.: 2,300 x 3,400 x 2,250 mmWeigh ...
usato
Pressa ad iniezione Yizumi Modello: YL2-V280L Forza di chiusura 2800 kN Volume: 2000cc Stampo corsa aperta 500mm Altezza minima dello stampo 100 mm Dimensioni piano riscaldato 670 mm x 780 mm Piastra riscaldante luce diurna 600 mm Pressione di iniezione 1970 bar Volume teorico dell'iniezione 2000cm3 Potenza pompa olio 11kW Pressione di sistema 230 bar Potenza totale 37kW Alimentazione: 415V, 50Hz, 3P+N+PE Pompa variabile Rexroth + servomotore Inovance: Anno 2021 Marchio CE