Fabbricante:
(Categoria: 307)
Key data: 660 mm, 2100 mm
4 nn. Mulini Buzuluk 84" disponibili! Rulli forati, cuscinetti a rulli, regolazione elettrica del nip, trasmissione Bullgear 2 x guida a sinistra 2 x Guida a destra Descrizione allegata!
estrusore sottovuoto con alimentazione a freddo Troester 90 mm x 18 D, con rullo di alimentazione, azionamento 46 kW, velocità della torta da 10 a 60 giri/min, 5 TCU,
estrusore a freddo - 60 mm x 18 D vuoto, con rullo di alimentazione, azionamento 22 KW, velocità della vite da 10 a 60 giri/min, con pompa ad ingranaggi, 5 TCU,
disponibile è un impianto completo con attrezzature per produrre molle pneumatiche! Calandra a 3 rulli con linea e Twin Mill da 84" Taglierina in sbieco Diverse macchine edili diverse presse idrauliche di polimerizzazione macchina per prova 3 linee di assemblaggio Avvolgitore ...
Key data: 2000 mm, 1300 mm
disponibile Berstorff Bias Cutter Angolo 0-50 gradi con giunzione manuale 90 gradi con giunzione automatica Certificato CE Descrizione allegata!
Estrusore a freddo degli anni '90, GE 90 x 16 D Vac, marca Troester, con tubo flessibile / testina di spruzzo profilata grande, azionamento 52 KW Siemens AC, 4 TCU Siengle
clamping force: 4.000 kNinjection volume: 4.000 cm³screw diameter: -- mmplaten size: 800 x 710 mmCondition: used,Specification: Rubber Injection Molding Machine - second-handclamping unit:- Clamping force: 4000 kN- heating platen size: 800 x 710 mm- ejection device: 2-layerInjection unit:- Injection volume max.: 4,000 cm³- Original screw 1005.10.008 B/cThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
clamping force: 350 kNinjection volume: 58,5 cm³screw diameter: 28 mmplaten size: 260 x 254 mmCondition: used,Specification: injection moulding machine for TPE - usedclamping unit:- clamping unit: vertical- clamping force: 350 kN- opening stroke max.: 300 mm- platen distance max.: 500 mm- Mould installation height min.: 200 mm- Clear width between tie bars: 260 x 254 mm- Ejector stroke max.: 80 mm- Clamping unit: VV- Lift of protective bonnet: 500 mmInjection unit:- Screw diameter: 28 mm- Screw L/D ratio: 18.6- Screw stroke max.: 95 mm- Injection volume max.: 58.5 cm³- Injection pressure: 1577 bar- Plasticising flow: 8.6 g/s- Injection flow: 85.5 g/s- Connected load: 3x 400 V, 50 Hz- Max. heating power: 5.8 kW- Drive power: 7,4 kW- Total power: ...
clamping force: 4.000 kNinjection volume: 2.700 cm³screw diameter: -- mmplaten size: -- mmCondition: used,Specification: Rubber Injection Molding Machine - second-handclamping unit:- Clamping force: 4000 kN- ejection device: 2-layer- Brush system: 2-layerInjection unit:- Injection volume max.: 2,700 cm³Two identical systems are available.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll diameter: 400 mmroll length: 1000 mmrolls drilled: Kernbohrung Nip adjustment: hydraulisch total power requirement: 45 kWCondition: used, overhauledSpecification: Rolling mill 400 x 1000 mm - second-hand monobloc model, motor under the rollers- roller diameter: 400 mm- roll length: 1000 mm- Rolls: with core bore, with central chamber for water cooling- Fixed friction between the rollers- Rollers mounted on bronze bushes with circulating oil lubrication via pump,- equipped with new Johnson-Fluiten slewing rings, for connection to the water circuit- Gap adjustment: hydraulic, NEW- Hydraulic unit: NEW- Manually tiltable steel guide plates with mechanical safety lock with mechanical safety interlock- Stainless steel roller container for holding the mixture- bi-directional safety bell ...
roll diameter: 660/700 mmroll length: 2100/1800 mmrolls drilled: Kernbohrung nip adjustment: motorisch drive power:: -- kWCondition: usedSpecification: 4-Roll L-Calender - Line - second-hand 4-roll Buzuluk L-calender 700x1800 Mixing mill Buzuluk 660x2100Complete 4-roll L-calender line.The line was used for the production of transparent PVC.However, the basic machines can also be used for rubber.The most important machines in the line:Pos. 8: Liquid mixer make Trusionma hot and coldPos. 10: KO Kneader make BUSSItem 12: Buzuluk 660x2100 mixing roller millItem 14: 4-roll L-calender make Buzuluk 700x1800Items 15-19: Tempering and basin equipment behind the calender Roller conveyorItem 20: Layer thickness profile measuring deviceItem 23: Rewinding deviceThe system was used for transparent soft PVC.Machines are still installed.The data for this ad wa ...
machine measurements: 2.100 x 2.200 x 2.100 mmmachine weight: 2.000 kgpower capacity: 36 kWCondition: usedSpecification: cleaning and degreasing system FIRBIMATIC LOGICA 200V closed cleaning system for the cleaning of of metallic components with highly stabilised perchloroethylene - second-hand- Closed cleaning system for the cleaning of metallic components components with highly stabilised perchloroethylene.- PER-based cleaning and degreasing system Possible cleaning cycles: 1. pre-cleaning (spraying) 2. main cleaning (spray and flood cleaning) 3. rinsing (hosing down) 4. vapour degreasing 5. vacuum drying- All cleaning cycles are freely programmable.- Filling volumes: Tank 1: 170 litres Tank 2: 80 litres- Type of solvent: Perchloroethylene- Total connected load of motors: 9.65 kW- Installed e ...
diametro del provino: - mmlunghezza del provino: - mmpotenza totale richiesta: - kWpeso della macchina ca.: - tdimensioni della macchina ca.: - mCampioni volumetrici - taglierina / punzone per campioni
disponibile Armonizzatrice per rettifica di PCR_Tyres sbilanciati Descrizione allegata! Certificato CE
Press force max.:: 3000 kNheating plates:: 600 x 630 mmelectrically heated:: °Cheating power:: kWpiston stroke:: 420 mmno. of stages:: 1 Condition: Used, reconditionedSpecification: Press 600 x 630 mm, second-hand- clamping force: 300 tonnes (3,000 kN)- closing: from bottom to top- Heating platens: 2 electric platens, with new heating rods- Heating platen dimensions approx.: 600 x 630 mm- Distance between the heating platens approx.: 420 mm- New electric valves- AC machine output oil pump: 5.5 kW- New control cabinet with Siemens 7’ touch panel- PLC control system make Siemens S7-1200- New cabling- Frequency inverter made by Schneider- Light barriers in the front area,Overhauled in accordance with CE standard safety regulationsOperating instructions and maintenance instructions in GermanWarranty: 1 yearThe data for this ad was created with ModulMWS - the sof ...
clamping force: 400 kNinjection volume: 125 cm³screw diameter: -- mmplaten size: 600 x 400 mmCondition: used,Specification: C-frame injection moulding machine for TPV - second-handclamping unit:- Clamping unit: vertical- Tonnage: 40 t- clamping force: 400 kN- Heating platen size: 600 x 400 mmInjection unit:- Injection volume max.: 125 cm³- Connected load: 3x 400 V, 50 Hz 90A fuse protectionApprox. dimensions: 1,550 x 1,050 x 3,120 mmWeight approx.: 2,250 kgTwo identical systems are available.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
clamping force: 400 kNinjection volume: 125 cm³screw diameter: -- mmplaten size: 550 x 400 mmCondition: used,Specification: C-frame injection moulding machine for TPV - second-hand, Modell TTV-C40-125 C40P01Bclamping unit:- Clamping unit: vertical- Tonnage: 40 t- clamping force: 400 kN- Heating platen size: 550 x 400 mmInjection unit:- Injection volume max.: 125 cm³- Connected load: 3x 400 V, 50 Hz 90A fuse protectionApprox. dimensions: 1,550 x 1,050 x 3,120 mmWeight approx.: 3,200 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Press force max.:: 1600 kNheating plates:: 400 x 400 mmelectrically heated:: -- °Cheating power:: 9,92 kWpiston stroke:: 400 mmno. of stages:: 1 Condition: Used,Specification: Press 400 x 400 mm, second-hand steel frame construction- Clamping force: 160 tonnes- pressure force: 1600 kN- Operating pressure: 300 bar- Closing: from bottom to top- Heating platens: 2 electric platens- Heating power: 4.96 kW/platen- Heating platen dimensions: 400 x 400 mm- Specific pressing pressure: 1000 N/cm²- Distance between the heating platens: 500 mm- Piston stroke: 400 mm- Piston diameter: 260 mm- AC motor power: 7.5 kW- Pneumatic protective cover in the front area,- lifting device- Sliding table- Approx. dimensions: 1,760 x 1,150 mm- System height approx.: 2,470 mm- Weight appro ...
clamping force: 200 kNinjection volume: 80 cm³screw diameter: -- mmplaten size: 350 x 300 mmCondition: used,Specification: C-frame injection moulding machine for TPV - second-handclamping unit:- Clamping unit: vertical- Tonnage: 20 t- clamping force: 200 kN- Heating platen size: 350 x 300 mmInjection unit:- Injection volume max.: 80 cm³- Connected load: 3x 400 V, 50 Hz- Pump output: 11 kW- Total output: 44 kWDimensions L/W/H approx.: 2,000 x 1,500 x 2,500 mmSpace requirement approx: 3 m²Weight approx.: 2.500 kgThere is also an identical system as a spare parts dispenser as an optionfor an extra charge. The control panel is missing here.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
clamping force: 400 kNinjection volume: 125 cm³screw diameter: -- mmplaten size: 300 x 300 mmCondition: used,Specification: C-frame injection moulding machine for TPV - second-handclamping unit:- Clamping unit: vertical- Tonnage: 40 t- clamping force: 400 kN- Heating platen size: 300 x 300 mmInjection unit:- Injection volume max.: 125 cm³- Connected load: 3x 400 V, 50 Hz 76A fuse protection (incl. peripherals)- Pump output: 7.5 kW, 14.9 A- Total output: 28 kWDimensions L/W/H approx.: 2,000 x 1,500 x 2,500 mmWeight approx.: 2,250 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
clamping force: 200 kNinjection volume: 80 cm³screw diameter: -- mmplaten size: 350 x 300 mmCondition: used,Specification: C-frame injection moulding machine for TPV - second-handclamping unit:- Clamping unit: vertical- Tonnage: 20 t- clamping force: 200 kN- Heating platen size: 350 x 300 mmInjection unit:- Injection volume max.: 80 cm³- Connected load: 3x 400 V, 50 Hz- Pump output: 11 kW- Total output: 44 kWDimensions L/W/H approx.: 2,000 x 1,500 x 2,500 mmSpace requirement approx: 5 m²Weight approx.: 3.200 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
speed of feed:: 50 m/minfeed:: 5 - 99.999,9 mmcuts max.:: 70 - 80 Schnitte/mcross-section width:: 40 mmcross-section heigth:: 40 mmCondition: NEW,Specification: Hose and corrugated pipe cutting machine electric cutting machine - Cutting unit: Window cut with cutting bushes - Material diameter approx.: 4 - 40 mm - Transport by two drive belts - Max. distance between the belts: 45 mm - Belt adjustment via motor, adjustment via control panel - Belt adjustment via the centre - with a maximum speed of approx.: 50 m/min - Electrical contact pressure of the drive belts - Electronic length measurement from 5 - 99,999.9 mm Digital display - Step change: 0.1 mm - Cutting via electric motor - Quantity selectable: 1 to 99,999 ...
Convertitore-estrusore a freddo da 120 mm, GE 120 SC, marca Berstorff, capacità di produzione fino a 1.000 kg /h come estrusore di potenza con testa di spruzzatura a nastro, ricostruzione completa meccanicamente ed elettricamente nel 2024
clamping force: 2700 kNinjection volume: 3300 cm³screw diameter: -- mmplaten size: 780 x 670 mmCondition: used,Specification: vertical injection moulding machine for rubber NR, EPDM, SBR, NBR, CR, etc. - used, in very good condition 6 months in useclamping unit:- Euromap (size): 2700-7200- Clamping force: 2,700 kN- Heating platen size L/W/H: 780 x 670 mm- Distance between upper and lower platen: 970 mm- Stroke min.: 420 mm- Stroke: 550 mmInjection unit:- Injection volume max.: 3,300 cm³- Injection pressure: 2,180 bar- Nozzle contact force: 80 kN- Connected load: 3x 400 V, 50 Hz, N- Back-up fuse: 125 A- Pump drive: 265 bar- Drive power: 22 kW- Pump speed: 66 rpm- ...
clamping force: 2700 kNinjection volume: 3300 cm³screw diameter: -- mmplaten size: 780 x 670 mmCondition: used,Specification: vertical injection moulding machine for rubber NR, EPDM, SBR, NBR, CR, etc. - used, in very good condition almost unused!clamping unit:- Euromap (size): 2700-7200- Clamping force: 2,700 kN- Heating platen size L/W/H: 780 x 670 mm- Distance between upper and lower platen: 970 mm- Stroke min.: 420 mm- Stroke: 550 mmInjection unit:- Injection volume max.: 3,300 cm³- Injection pressure: 2,180 bar- Nozzle contact force: 80 kN- Connected load: 3x 400 V, 50 Hz, N- Back-up fuse: 125 A- Pump drive: 265 bar- Drive power: 22 kW- Pump speed: 66 rpm- C ...
Key data: 400 mm, 900 mm
disponibile 35" Fresa su Baseframe Maggiori dettagli nella descrizione allegata!
cross-section width:: Schläuche max. 11 mmcross-section heigth:: 11 mmfeed:: 0,5 - 100.000 mmCondition: used, very good conditionSpecification: universal cutting machine with roller drive for hoses - small cutting machine for hoses- feed unit: roller drive- microcontroller control: 80537- cutting unit: pneumatic- Type of cut: Blade cut- Industrial blade: for PVC hoses- Max. hose diameter: 11 mm- Maintenance unit: yes- Max. feed speed: 1 - 50 m/min - Cutting capacity max.: 450 cuts/min depending on the cutting length- Cutting force approx.: 500 N at 6 bar- Cutting length: 0.5 - 100,000 mm- Resolution/step change: 0.5 mm- Operating voltage: 230V, 50-60 Hz- Compressed air: 5 - 6 bar- Air consumption per stroke approx.: 0. ...
Press force max.:: 1.000 kNheating plates:: 480 x 520 mmelectrically heated:: °Cpiston stroke:: ca. 500 mmno. of stages:: 1 Condition: Used, overhauledSpecification: 4-column vulcanising press 480 x 520 mm, used- closing force: 100 t- closing: from top to bottom- heating plates: 2 electric plates- New heating platens- Dimensions of heating plates: 480 x 520 mm- Distance between heating platens approx.: 500 mm- AC motor: 5,5 kW- New electric valves- New control cabinet with Siemens 7 touch panel- SPS system Siemens S7-1200- Frequency converter make Schneider- New cabling- Light curtains in the front operating areaOverhauled according to CE standard safety regulationsOperating and maintenance instructions in GermanWarranty: 1 yearThe data for this ad was created with ModulMWS - the ...
cross-section width:: 800 mmcross-section heigth:: 15 mmfeed:: ab ca. 5 mmspeed of feed:: m/mincuts max.:: Schnitte/mcondition: used, overhauledSpecification: Panel cutting machine - overhauled with CE- Section width max.approx.: 800 mm- Section height max.: 15 mm, depending on the hardness of the rubber sheets- Cutting length from approx.: 5 mm (depending on material)- cutting force approx.: 10 tons - Connected load approx.: 1.8 kW- Painting: green- Operating voltage: 3 x 400V, 50Hz, N, PE- Dimensions approx.: 1,200 x 1,450 x 1,950 mm - Safety devices according to current standards,- New on-board system machine,- New control cabinet with PLC system Siemens S7-1200,- CE marking,- Instructions for use and maintenance in English or German language ...
cross-section width:: 40 (45) mmcross-section heigth:: 25 mmfeed:: 1 - 999.999,9 mmspeed of feed:: 1 - 60 m/mincuts max.:: 100 Schnitte/mCondition: used,Specification: circular knife cutting machine - second-hand for cutting rings, discs and profiles- diameter max.: 45 mm- 3 hoses or strands: 6 - 20 mm- 2 hoses or strands: 20 - 30 mm- 1 hose or string: 30 - 45 mm- cross section width max.: 40 mm- cross-section height max.: 25 mm- feed speed: 1 - 60 m/min, infinitely variable- Cutting capacity max.: 100 cuts/min depending on material and cutting length- Cutting length: 1 - 999.999,9 mm- Step jump: 0.1 mm- Feed by servo drive- Cutting by servo drive- Pulsed feed- Connected load approx.: 5 kW- Operating voltage: 3 x 400V, 50Hz, PE- Weight approx.: ...
Pelmar Engineering Germany GmbH
