NOTE additionally a new shaft Description Force , 4000 TN Slide stroke, mm 400 Number of continuous slide stroke, stroke / min 50 Closed height of stamping space mm 1000 Adjusting the table mm 15 Distance between columns in light,mm 1660 Drive power, kW 185 Table dimensions in plan mm: - From left to right in 1620 - Front-to-back in 1570 Dimensions in mm: - in the plan 6100 x 4710 - Height above floor level 6820 - Press height 8680 Weight, t 377

Nominal force: 6300 ton Number of continuous strokes per minute: 40 Ram stroke: 460 mm Distance between ram and table (table is in upper position): 1150 mm Table adjustment: 15 mm Distance between press columns: 1950 mm Ram dimensions: -front to back: 1680 mm; -left to right: 1680 mm Table dimensions: -front to back: 1950 mm; -left to right: 1920 mm Mechanical upper ejector: -max stroke: 100 mm; -number of positions: 1 -steps of stroke adjustment: 25-30-75 mm -force: 30 ton Pneumatic lower ejector: -max stroke: 300 mm -stepless stroke adjustment: 15-300 mm -number of positions: 3; -force: 65 ton Side windows dimensions: -width: 1100 mm ...

Effort 2000t moving matrix 280 mm landing pad 570 mm landing slider after closing the matrices 390 mm Number of moves of the ram, stroke / min 25 Electric motor power 160 kW Dimensions, mm: LWH = 856053604850, the level above the floor is 3200. Weight of the car without electricity: 239.8 tons. Weight of the bed: Front part: 82 tons. Rear part: 55t. Weight 270 ton

an older and used good cold rolling mill for the production of ribbed structural steel wire  ...

• more information

REVAMPED: 1990, WIDTH: 700-1400 MM, THICKNESS: 100 MICRONS - EXIT: 2 x 5 MICRONS 1500 M/MIN.,  ...

• more information

Qty. 1 Second-hand foil rolling mill plant Mfc.: World Co. (Japan) Type: 6-Hi – Non reversing mill Built: 2002 Application: Copper foil Width: 400 – 700 mm Coil weight: Max. 5 Ton Thickness Entry: 100 – 200 microns Exit: 5 – 100 microns Speed: 0-400/800 m/min. Thickness X-Ray unit AGC system Variable Crown Control Hydraulic servo equipment Main motor power: 200 kW DC Slitter line Mfc.: IHI Width: 150-700 mm Thickness 5 – 50 microns Degreasing line Mfc.: World Co. Strip width: 700 mm Thickness: 10-50 µm Treatment line Mfc.: Kawasaki Built: 2005 Width: 700 mm Thickness: 10-50 µm

Qty.1 Second-hand Aluminium cold rolling mill Mfc.: SPIDEM Type: 4-Hi Non Reversing Built: 1964 Installed: 2017 (new mechanical & hydraulic, PLC – ABB, AGC) Stopped: 2020 Strip width: 1700 mm Thickness Entry: 11 mm Exit: 0.2 mm Rolling speed: 450 m/sec. with edge trimming: 300 m/sec. Mill force: 1500 T WR Length: 1830 mm Dia.: 465 / 500 mm Back-up rolls Length: 1830 mm Dia.: 1100/1200 mm De-coiler Max. counter traction force: 5500 kgP Reduction ratio: 1:5.53 Revolution: 72.3 – 199 RPM Speed: 136.5 – 375 m/min. Coiler (2 x 400-1100 RPM) Max. traction force: 15000 kgP Reduction ratio: 1:4.41 (470 m/min.) Speed: 9.9 – 200 m/min.

STRIP WIDTH: 750 MM, ENTRY THICKNESS: 0.5 MM, EXIT: 2 x 0.007 MM,  ...

• more information

Qty. 1 Second-hand 3 stands 4-Hi Tandem cold rolling mill line Mfc.: Demag Type: 4-Hi Built: 1968 Material to be rolled: low carbon steel Strip width: 600 †1500 mm Thickness Entry: 2.5 mm Exit: 0.2 mm Entry: Coil ID: 510 mm OD: 1800 mm Weight: 15 MT Exit: Coil ID: 510 mm OD: 1800 mm Weight: 15 MT Work roll: dia. 380 mm x 1650 mm Roller bearings Back-up rolls: dia. 1150 mm x 1650 mm Oil film bearings Housing: Closed top, cast steel construction Housing post: 762 x 552 mm Rolling speed: 240 m/min.

Fliss bohrer and thread rolling NC machine. Machine was rebuilded in 2019, complete Hardwere, and pneumatic components, and part from electric. Machine can be used for serial tube production, can be aded Robot for manipulating. Machine will be able to connect with a handling robot for fast delivery and high productiion.