We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
NOTE additionally a new shaft Description Force , 4000 TN Slide stroke, mm 400 Number of continuous slide stroke, stroke / min 50 Closed height of stamping space mm 1000 Adjusting the table mm 15 Distance between columns in light,mm 1660 Drive power, kW 185 Table dimensions in plan mm: - From left to right in 1620 - Front-to-back in 1570 Dimensions in mm: - in the plan 6100 x 4710 - Height above floor level 6820 - Press height 8680 Weight, t 377
Nominal force: 6300 ton Number of continuous strokes per minute: 40 Ram stroke: 460 mm Distance between ram and table (table is in upper position): 1150 mm Table adjustment: 15 mm Distance between press columns: 1950 mm Ram dimensions: -front to back: 1680 mm; -left to right: 1680 mm Table dimensions: -front to back: 1950 mm; -left to right: 1920 mm Mechanical upper ejector: -max stroke: 100 mm; -number of positions: 1 -steps of stroke adjustment: 25-30-75 mm -force: 30 ton Pneumatic lower ejector: -max stroke: 300 mm -stepless stroke adjustment: 15-300 mm -number of positions: 3; -force: 65 ton Side windows dimensions: -width: 1100 mm ...
Effort 2000t moving matrix 280 mm landing pad 570 mm landing slider after closing the matrices 390 mm Number of moves of the ram, stroke / min 25 Electric motor power 160 kW Dimensions, mm: LWH = 856053604850, the level above the floor is 3200. Weight of the car without electricity: 239.8 tons. Weight of the bed: Front part: 82 tons. Rear part: 55t. Weight 270 ton
Hot forging press Kurimoto C2F-16 Year: 2002 Capacity: 1600 ton Stroke: 200 mm Stroke per minute: 60 Die height: 707 mm Bolster area: 1265x890 mm Adapter area: 930x1065 mm Main motor: 75kW, 480V ...
Stamping pressure : 40 kN Stamping area : 150 x 210 mm Stamping die holding plate : with dove-tail guiding Stroke of plunger : 28 mm Daylight (adjustment of height) : 0-180 mm Throat (middle of stamping plate to bow) : 190 mm Foil feeding system : motor-driven, 1-fold running from the left to the right side with foil re-winding device Working table : sliding automatically in and out with table lock pneumatic, 400 mm x 450 mm PLC : Siemens S 7-1500 with TP 700 color Safety device : in CE-execution with safety light curtains in front Color of the machine : light grey RAL 7035 Voltage: 3 x 400 VAC (L1/L2/L3/N/PE), 50 Hz. Pneumatic access : oil and water free compressed air, ...
Fully automatic hot stamping press Oropress Mechanical eccentric press with lift table Lift table as pneumatic sliding table 250 x 250 mm Fully automatic sequence, optionally triggered with foot switch for single stroke Heated press punch 120 x 200 mm up to 250 °C Safety grille Film Feed Unit Built in 1986
Hot riveting installation consists out of: - 1 = orange riveting clamp mounted on a green chassis + induction heater with 2 positions - 2 = mobile induction heater with 3 positions - 3 = mobile induction heater with 2 positions - 4 = mobile induction heater with 3 positions - 5 = separate green riveting clamp - 6 = blue riveting clamp mounted on a green jib crane + induction heater with 2 positions - 7 = tooling dies
Hot Water Boiler Plant Schmid 2400 kWth with moving step-grate This Schmid boiler contains a durable, electronically controlled, water cooled moving grate which is designed to burn from wood pellets to wood chips and waste wood. The plant was installed in year 2012 and it has been running with wood pellets till December 2022. It is complete, good condition plant with concrete element building, two large pellet silos and a hot water accumulator tank for heat load balancing. These items will be optionally available for those who are interested in them. It has load controlled primary and secondary air combustion fans as well as speed-controlled exhaust gas fan which ensures high efficiency ...
General SKU231U210 LocationBarneveld MakePlasmec TypeTRM 200 No.14604897 Year of construction1997 Pressure Working pressure8 Bar Main Features MaterialStainless steel Volume200 Ltr. Motor36 KW Specified Features - Hot mixer Hot/Cold mixercheck Capacity200 Ltr. Vessel sizesDia: 700x580 mm With jacketcheck With motor18-36 kW 400 Volt Pneumatic operated outletcheck(as is) Outletdia. 240 mm MaterialStainless steel Information With switchgearcheck (as is) Total height1,2 m Weight810 kg CEcheck Floorspace2x0,9 mHot mixersPlasmecPlastic machinery > Hot mixersBrand > Plasmec What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared ...
General SKU041F169 LocationBarneveld Pressure Working pressure1 Bar Main Features MaterialStainless steel Volume630 Ltr. Motor145 KW Specified Features - Hot mixer MaterialStainless steel 1.4571 (316Ti) Hot/Cold mixerPxx compounder (1x) CapacityN-TSHK 630 High Speed mixer = 630 Ltr Vessel sizesdia. 935x950mm With jacketcheck Max. temperature220 Degr. C. With motor115,0/145,0 KW, 380 Volt Pneumatic operated outletdia. 250mm Cold mixertype HCC-2000 High Capacity Cooling System Capacity2000 Ltr Vessel sizesdia. 1000x2000mm With jacketMixing shaft can be cooled With motor37,0 KW, 380/660 Volt With lump breaker(2x) Motor4,4/5,5 KW, 380 Volt (1420/2860 Rpm) Information M ...