Üretici:
(kategori: 107)
kesme boyutları maksimum: 600 x 1000 mm plaka kalınlığı: maksimum 3 mm kesme açısı: 1,5 yan stop elektrik ayarlanabilir: 0 - 1010 mm arka stop elektrikli ayarlanabilir: 0 - 610 mmno. stroklar: 60 Hub/minimum toplam güç gereksinimi: makinenin 14 kW ağırlığı ca.: 8,7 tboyut makine L x B x H: 2,5 x 2,18 x 2,3 mAksesuarlar: raylar üzerinde sac metal istifleme cihazıBu reklamın verileri, LogoTech oHG'nin yazılım çözümü olan ModulMWS ile oluşturulmuştur.
sheet width: 3140 mmplate thickness: 6.5 mm STthickness at Niro-steel: 4.0 mm VAbending angle max.: 0 - 135 °daylight opening: 100 mmback stop - adjustable: max. 800 mmControl: M 15 S total power requirement: 7.5 kWweight of the machine ca.: 6350 kgdimensions of the machine ca.: 4350 x 2250 x 1900 mm current new price approx. 60.000 euros special price on requestDescription :- robust folding machine- high precision for wide bending processes- increased rigidity in design- hydraulic drive- with rack and pinion for better control and accuracy- compared to normal hydraulic systems Easy adjustment of material thickness Adjustable hydraulic pressure to adjust the thickness of the material This prevents damage to the surface of the materials- Smallest return bend 25 mmEquipment:- Program control M 15 S with LED display for bending angle adjustment- Manual backgauge 0 - 800 mm- Manual lower be ...
sheet width: 1350 mmplate thickness: 4.0 mmthickness at Niro-steel: 2.0 mmno. of strokes: max. 35 Hub/mincutting angle: 2.0 Gradtable height: 945 mmdistance between columns: 1361 mmControl: CIDAN / SIEMENS engine output: 5.5 kWweight of the machine ca.: 1400 kgrange L-W-H: 2200 x 2000 x 1550 mmFeatures:- robust / motorized swing cut guillotine shears- unbreakable and torsion-free welded steel construction- compact and clear machine construction- NC electro-motorized backgauge, with digital display Target / actual value stop value input stepless adjustment over the entire travel range- 1x hold-down bar- 1x material side stop- recessed grips in the front support table- Manual cutting gap adjustment from the front- Rear sheet holding device for thin sheets- 1x freely movable foot switch- Operating instructions (PDF)The data for this ad was created with ModulMWS - the software solution of Lo ...
New V8, 5x 515mm 1x 550mm divided, wila shot Auction-ID: A1-43823-233
Y1, Y2, X1, X2, R1, R2, Z1, Z2, Crowning, hydraulic top and bottom tool clamping, tool changer/shutting crush function, 2x bending aid, double foot pedal, oil cooler Includes many top and bottom tools Auction-ID: A1-43823-237
: neu : 2024 : 9722 : prompt, Zwischenverkauf v : Türkei : 16600 €: 318.72 €: 1 : 2050 mm: 3 mm: 130 mm: 3,5 m/min: 2.2 kW: 3200 mm: 750 mm: 1000 mm: 1500 kg3 rollsasymmetric rolls - prebending2 rolls driven by brakemotorHARDENED ROLLSmanual Back Rollforward tiltable upper rollforward and reverse revsconical bending by tilt of backrollmovable control panelusers manual in GERMANOPTIONS:(time of delivery with options approx. 8 weeks)Motorised Back Roll (Power Rear Roll) Digital Read-OutThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 12 - 14 Wochen ab Auf : Türkei : 98600 €: 1863.54 €: 3100 mm: 16 mm: 16 mm: 13 mm: 16 mm: 14 mm: 12 mm: 300 mm: 300 mm: 240 mm: 50 mm: 1140 mm: 18.5 kW: 5310 mm: 1660 mm: 1140 mm: 11100 kg4 rollsfully hydraulic drive of upper and lower roll (from 30 mm bending capacity all four rolls) by planetary gear boxhydr. side rolls positioning with electronical synchronisationhydr. lower roll feed with mechanical synchronisationadjustable pinching pressurevariable rolling speedhardened rollsconical bending devicehydraulic drop-end bearingmoveable control paneloverload protectionuser manual in GERMAN or ENGLISHaccording to CE rulesOPTIONAL:NC controlupper and lateral supportsIMPORTANT ISSUES AT CONICAL BENDING:the max. sheet metal thickness isequivalent to 50 % of nominal capacityThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: gebraucht : 1968 : 9581 : 3200 €: 1 : 1050 mm: 2 mm: 150 1/min: 500 mm: 1500 mm: 1700 mm: 1100 mm: 800 kgman. back gauge with hand wheel and scaleuser manual in GERMANdidn&apos,t according to CE rulesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 12 Wochen ab Auftrags : Türkei : 19100 €: 366.72 €: 4000 kg: 1300 mm: 450 - 550 mm: 600 mm: 50 mm: 80 mmmotorized drivemechanical adjustable coil mandrel with 4 jawsspeed control for decoiling speed aswell as acceleration- and deceleration timesphotoelectric proximity ensor SICK for sag controlAlternative:Variant with pneumatic pressure arm (CMC P3 4000 600 M D1300) € 21.800,--The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 12 Wochen ab Auftrags : Türkei : 20000 €: 318.72 €: 16600 €: 1270 mm: 5 mm: 5 mm: 4 mm: 5 mm: 4 mm: 4 mm: 3 mm: 130 mm: 130 mm: 130 mm: 5 m/min: 3020 mm: 1150 mm: 1110 mm: 2150 kgmotorized roller driveupper and lower roller drivenhydraulic side roll feed3 digital displayshydraulic folding bearingshardened rollersconical bending deviceuser manual in GERMAN or ENGLISHOPTIONAL EQUIPMENT:overhead craneside supportsNC controlvariable speedThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 2 - 4 Wochen ab Auftr : Niederlande : 4955 €: 3/4 26,9 mm, 1 33,7 mm, mm: 5 mm: 3 mm: 87 kgThe motor driven AL 1-2E can be used to notch pipes with an external diameter of 26.9 mm (3/4",), 33.7 mm (1",), 42.4 mm (1 1/4",), 48.3 mm (1 1/2",) and 60.3 mm (2",).Do you often have to notch pipes? If so, the motor-driven AL1-2E equipped with a 2.2 kW electric motor is the ideal solution!The motor forms one unit with the special eccentric shaft that drives the notching tool. The motor is also equipped with an on/off switch with a zero voltage protection and guard.All the benefits in a nutshell: high productivity, low investments, simple and rapid operation, a number of diameters are readily available, ideal for double corner joints.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3355 mmplate thickness: 63,5 mmroll diameter: 686 mmvoltage: 400 Vtotal power requirement: 150 HPweight of the machine ca.: 95 tdimensions of the machine ca.: 62 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : 2024 : 9738 : prompt, Zwischenverkauf v : Türkei : 20300 €: 389.76 €: 1 : 1530 mm: 6 mm: 6 mm: 4 mm: 150 mm: 4 kW: 3100 mm: 1120 mm: 1020 mm: 2100 kg3 rollsAsymmetrical rolls arrangement - with pre-bending2 driven rollsMotorized adjustment of lateral and clamping rollDigital read-out for lateral and clamping rollSwiveling top roll to the frontForward/reverse runHardened rollsMoveable control panelUser manual in GERMAN and ENGLISH(sample photo)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2520 mmplate thickness: 2.50 mm STthickness at Niro-steel: 1.50 mmupper clamping bar adjustment: 160 mmadjustment speed: 100 mm/secAdjustment folding beam: 80.0 mmBending speed: ca. 120 Grad/seccompressed air: 6.0 barwork height max.: 869 mmcontrol: POS 2000 voltage: 400 Vtotal power requirement: 7.2 kWweight: 3430 kg Current new price ~ 100.000 euros From a maintenance workshop With very good equipment ()Equipment:- CNC electric motor-driven universal swivel bending machine High-precision mechanics with modern control technology For individual and series production Robust high-speed machine with high axis speeds Torsion-free welded construction - Rotatable upper beam / as automatic tool change system With 2x tool stations (sharp and goose foot bending rail) Reduces set-up and idle times Eliminates time-consuming tool changes and adjustments- SCHRÖDER CNC control model POS ...
: 1 Bu reklamın verileri, LogoTech oHG'nin yazılım çözümü olan ModulMWS ile oluşturulmuştur.
punching force max.: 50 tthroat: 510 mmstroke: 32 mmstroke - stepless adjustable: 10 - 32 mmno. of strokes: 35 bei 10 mm Hub/minWorking height: 1070 mmdaylight: 350 mmtable width: 255 mmdimensions: ca. 1080 x 650 x 1680 mmmaterial layer: 630 X 535 weight: ca. 1400 kgScraper, height-adjustable and removable, with interchangeable plateHydraulic low-pressure finder for foot switch operationTwo-stage foot switch and electrical controlsIntegrated hydraulic unitWith punching saddle for dies no. 3 and 4, up to Ø 39.5 mmQuick-change device for punches 3 and 6 up to Ø 39.5 mmPeddinghaus blue serieswith material support table no. 513, dimensions 630 x 535 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 4000 mmplate thickness: 30 / 35 mmpre-bending: 30 mmdiameter of upper rolls: 570 mmside roll diameter: 450 mmdiameter of lower rolls: 540 mmbending speed: 4 m/minmin. bending diameter: 650 mmtotal power requirement: 60 kWweight of the machine ca.: 52 todimensions of the machine ca.: - mThe machine was overhauled in 2022Equipment:- Hydraulic 4-roller round bending machine- Roll material: 61 MnCrMo 43- Driven rolls: 2 Top-and bottom roll-- Drive: over 2 hydro motors direct flanged-- Adjustment speed bottom roll: 0-200 mm/min-- Adjustment speed side rolls: 0-700 mm/min- Speed compensation between top-and bottom roll: automatic- Operation of the tilting bearing: hydraulic- Tilting of the top roll: hydraulic- Bearing block: hydraulic- Indicator device of roll position: digitalThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width - max.: 5-150 mmsheet width - max.: 5-150 mmcoil weight: 2,0 tcoil weight: 2,0 tBelt thickness: 0,2-1,5 mmBelt thickness: 0,2-1,5 mmband speed: 0-20 m/minband speed: 0-20 m/mindriving torque: 290 Nmdriving torque: 290 Nmtable-size: 1500 mmtable-size: 1500 mmControl: Siemens-Leicht Control: Siemens-Leicht range L-W-H: 2.000 x 1.500 x 1.900 mmtotal power requirement: 0,75 kWtotal power requirement: 0,75 kWweight of the machine ca.: 0,6 tweight of the machine ca.: 0,6 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2050 mmplate thickness: 4,5 mmpre-bending: 4,0 mmmin. dia.: 210 mmroll diameter: 140 mmweight of the machine ca.: 1530 kgdimensions of the machine ca.: 3220x1200x900 mmStandard features:- Central rollers via electric motor, planetary reduction gear andGear drive driven- Swivel top roller- Main engine with brake device- Conical bending device- Mobile controller and foot pedal- CE mark / Declaration of ConformityAdditional equipment:- motorized rear roller adjustment- Digital display for back roller- induction hardened rollsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Malzeme genişliği: 0400 mmcoil ağırlık: 1,50 malzeme kalınlığı: mmnomb. düzleştirme ruloları: 9 diametr. rulo civarı: 30 mm genleşme aralığı yaklaş.: 460 - 530 mm dış bobin - diametr. yaklaşık 1500 mmToplam güç gereksinimi: Makinenin kW ağırlığı ca.: makinenin boyutları ca.: mBu reklam için veri, LogoTech oHG'nin yazılım çözümü olan ModulMWS ile oluşturulmuştur.
: neu : 2024 : 9729 : prompt, Zwischenverkauf v : Türkei : 28450 €: 488.96 €: 1 : 25600 €: 1550 mm: 7 mm: 7 mm: 4.5 mm: 4.5 mm: 3.5 mm: 150 mm: 150 mm: 130 mm: 1,5 / 6 m/min: 4 kW: 3750 mm: 960 mm: 1100 mm: 2500 kg4 rollsTop rolll driven by hydromotor and planetary gearbox, bottom roll driven by gear and cardan systemPinch roll and latereal rolls move with hydraulic cylindersDigital read-out for lower and side rolls positionHardened rollsConical bending deviceHydraulic load relieving of upper rollHydraulic drop-end bearing2 working speedsProtectionagainst overloadMoveable control paneAccording to CE rulesOPTIONAL EQUIPMENT:(time of deliver with options approx. 10 weeks)Infinitely adustable speed of rollsHydraulic side supportHydraulic top supportNC controlIMPORTANT ISSUES AT CONICAL BENDING:The max. sheet metal thickness isequivalent to 50 % of nominal capacityThe cone length can ...
: : : toplam güç gereksinimi: makinenin kW ağırlığı ca.: makinenin boyutları ca.: mBu reklamın verisi, LogoTech oHG'nin yazılım çözümü olan ModulMWS ile oluşturulmuştur.
working width: 1500 mmworkpiece width - max.: 0,5 - 50 mmdimensions: 3300 x 1500 x 1800 mmfeed stepless: 0-4 m/mintotal power requirement: 20,4 kWweight of the machine ca.: 2800 kgThe SBM-L G1S2 grinding and deburring machines were developed for double-sided deburring and edge rounding of workpieces in a single operation. LISSMAC machines are used for deburring sheet metal and processing sheet metal parts, laser parts, and stamped parts.The L series is equipped with three units on the top and bottom . Workpieces made of stainless steel, steel, aluminum or non-ferrous metal can be processed on the top, bottom or both sides. Processing sheet metal on both sides and rounding edges in a single operation saves up to 60% in time. It is also possible to easily connect automation solutions or integrate the machine into production lines. The machine design ensures ergonomic working and a pleasant ...
sheet width: 3050 mmplate thickness: 6 mmrear stop: 1000 mmcutting angle: 0,5 - 3 °down holder: 18 Stkno. of strokes: 9-17 Hub/mintotal power requirement: 7,5 kWdimensions of the machine ca.: 3800 x 2000 x 1600 mmweight: 4500 kgEquipment:- electric backgauge- electric cutting angle adjustment- manual cutting gap adjustment- SP 9 control unit- Safety guard behind the machine incl. light barrier- front finger guard- 1x side stop- operating instructionsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3050 mmplate thickness: 12 mmrear stop: 1000 mmcutting angle: 0,5 - 3,0 °down holder: 18 Stkno. of strokes: 7 - 14 Hub/minoil volume: 350 ltotal power requirement: 22,5 kWdimensions of the machine ca.: 4200 x 2000 x 2250 mmweight: 8500 kgEquipment:- Haco SP 8 control unit- electro-hydraulic guillotine shears - guided by a guide rail- electric backgauge- electric cutting gap adjustment- electric cutting angle adjustment- 1x side stop- front finger guard- rear safety device ( light barrier )- emergency stop device- 1x freely movable foot switch- operating instructionsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3060 mmplate thickness: 6.0 mmthickness at Niro-steel: 4.0 mmdistance between columns: 3100 mmdown holder: 16 Stückno. of strokes: max. 10 - 15 Hub/minoil volume: 160 ltr.cutting angle: 1.6 °back stop - adjustable: 6.0 - 750 mmControl: ELGO P9521 total power requirement: 18.5 kWweight: 6300 kgrange L-W-H: 3900 x 2300 x 1630 mmFeatures:- Robust electro-hydraulic swing beam shear- ELGO digital display model P9521, for electric backgauge Backgauge travel X = 750 mm Backgauge-free ball screw drive Travel speed 100 mm/s- 1x stable side stop With T-slot, flip-stop, and millimeter scale- 2x stable front support arms- Electric cutting length limiter Cutting length limiter to increase the stroke rate/min.- Manual cutting gap adjustment Centrally operated on the right side stand- Front support plates- Front finger/interference guard- Inching operation with push buttons on the left c ...
working width: 1000 mmworkpiece width - max.: 0,5 - 50 mmsandingbelt width: -- mmweight of the machine ca.: 2,5 tWith the SBM-L 1000 G1S2, which works in the dry process, in alternating operationSteel, stainless steel and aluminum can be machined. She deburrs and roundsthe edges on the outer and inner contours of punched, laser, fine plasma orwater jet cut workpieces with a thickness of up to 50 mmon both sides in just one operation. Two sanding units, 1 each on the top and bottom, remove spatterand slight burrs on outside and inside edges of sheet metal. A total of four sanding belts, 2 each on the top and bottomUnderside, process the sheets on both sides at the same time. hereAll edges are softened or rounded, depending on the tool settings. Machining on both sides saves time-consuming turning of the workpieces andedit twice. All pairs of aggregates can be switched on/off separately de ...
10 € 
