Sac levha makası

Working length: 3,100 mm Cutting capacity: 6 mm Backgauge range: 1,000 mm Equipped with: - Sheet metal holding device at the back - 3 sheet metal support arms - Foot pedal Country of origin: France Motor power: 7.5 kW Machine LxWxH: 3,800 x 2,100 x 1,860 mm Machine weight: 6.000 kg

Description with exact angle system cutting width 50cm

Cutting length : 4100mm, Max. sheet thickness 10mm,

System: Oscillating cut Cutting thickness max: 12 mm Cutting length max: 3,000 mm Knives: 1 set new, 1 set used Machine weight 14.000 kg Machine dimensions LxWxH: 4.040x2.850x2.450 mm

Working length: 3,050 mm Cutting capacity: 6 mm steel 4 mm stainless steel Backgauge range: 1,000 mm Cutting angle adjustment: 0.5 - 2.5 degrees Equipped with: - 4x sheet metal support arms - Foot pedal - Sheet metal holding device at the back - Safety light curtain at the back Country of origin: Italy Motor power: 7.5 kW Machine LxWxH: 3,500 x 2,200 x 1,700 mm Machine weight: 6.600 kg

sheet width: 1275 mmplate thickness: 3 mmstrokes per minute until: 35 cutting angle: 2,0 °table height over floor: 870 mmthickness at Niro-steel: 2 mmtotal power requirement: 3 kWweight of the machine ca.: 875 kgrange L-W-H: 1,7 x 1,68 x 1,1 mElectric 380 Volt: Back stop with manual adjustment: Shadow line lighting: Foot switch: Piece counter: Squaring arm: Support arms: The guillotine shears type SMP is a well-dimensioned machine withall-welded gate guides. The drive takes place with a standard geared brake motor via a chain connection to the main axis. The knives are of the highest quality. The optimal cutting angle ensures together with the rubber-coated sheet metal holder, perfect cuts.Bearings and guides are maintenance-free and lubrication-free.Standard equipment: • Back gauge 635 with mm scale. •Cutting line lighting. • Section counter. • Table extensions 600 mm.  ...

sheet width: 170 mmplate thickness: 0 mmnumber of rolls: 0 weight of the machine ca.: 0,1 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Machine type: Sheet metal scissors (lid scissors) Manufacturer: MÜLLER & KURTH Condition: very good Offer type: used machine Specifications: Power: 1100 x 1.0 mm Drive type: by hand Remark: Parallel stop, Hold Weight: 300 kg The machine is in a very good and immediately ready for use condition and can be visited and demonstrated with us. We would be pleased if our offer finds your interest. Errors, changes and prior sale excepted.

Combined CNC – controlled press brake / sheet metal shears Super compact machine with a very small footprint. Maximum cutting length 3,020 mm Nominal cutting capacity 6 mm sheet steel/ST 40 Cutting angle 1°30" 17 pieces of sheet metal hold-down, Ø hold-down plate 50 mm NC – controlled back gauge for guillotine shear station - adjustment range 750 mm Table height 750 mm. Maximum bending length between the side stands: 3,440 mm (column passage 3,550 mm) Maximum pressing force 1,000 kN Working height bending only 1,230 mm Lifting range bending station 170 mm Maximum installation height of the bending station is 250 mm (press beam surface in the lowest position), the backgauge adjustment range for the bending station is 750 mm. Dimensions including operating pendulum 4.25 m x 1.82 m x H 2.8 m Footprint 3.85 x 1.82 m Drive power 10 kW Weight 9,000 kg Equipment: ...

NC - controlled mechanical sheet metal panel scissors in backdrop cutting design, maximum cutting length 1,050 mm, maximum cutting capacity 4 mm steel sheet/ST40, cutting angle 1.5°, NC - controlled rear stop with 1,000 mm travel range - automatic removal of the stop rail at sections lower than 1,000 mm - optionally available with a foldable sheet support at the rear stop or a conveyor belt with upliftrs, drive power 5 kW, weight approx. 2,500 kg

Description heavy automatic hydraulic plate shears / guillotine shears up to 50mm with cycle feed Working width approx. 155cm Thickness max. 50mm

Plate shears Cutting capacity 1 mm Cutting width 1.10 m Foot operation, the cross step is missing.