We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
used
Key data: 250 mm, 500 mm
Circulation diameter over bed 500 mm Max. turning length 1,600 mm Connected load 5.5 kW Machine weight 4.4 t
used
Metal lathe make WMW Karl-Marx-Stadt type DLZ 355 x 1600Fabr. -No: 2410/60, built in 1960Technical specifications:Technical specifications:Turning length: 800 mmCircumferential diameter over bed: 355 mmCenter height: 180 mmSpindle bore: 35 mmTailstock tip taper: Morse 4Quill shift by hand: 140 mmTailstock shift of the upper part from the central position: 10 mmWorkpiece weight between the steadies: 630 kgbetween the tips: 400 kg18 spindle speeds: 18 - 2500 rpm16 feeds length: 0.071 - 1 mm / rev16 cross feeds: 0.036 - 0.5 mm / revmetric thread 16: 0.5 - 7 mmInch thread 28:60 - 4 turnsModule thread 1 0.25 - 3.5Main drive: 5.8 kWExternal dimensions: 2200 x 1060 x 1225 mm highWeight: 1900 kgWith- three-jaw chuck- Steel holderused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. ...
used
Tip height: 1250 mm Turning diameter: 2,500 mm over bed Centre distance: 4.000 mm Support motion: 750 mm longitudinal feeds 630 mm cross feeds Face plate: Ã? 1250 mm Spindle speed: 5.6-280 RPM. Spindle bore: 100 mm Workpiece weight: 10.000 kg Equipped with: -Floor plates 4.500 x 2.200 mm -Powered tailstock -Operating instructions Country of origin: Germany Engine power: 45 kW Machine weight: 18,000 kg Machine Lxwxh: 8,000 x 4,000 x 2,100 mm
used
Code 151295 Description Facinglathe with center Make WMW NILES Model DP 1 / S 2 Serial number 261 526 149 Year of make 1986 Max. centerheight over base plate 1250 mm Max. swing over base plate 2480 mm Max. swing in Gap 3100 mm Distance between centers 4000 mm Max. workpiece weight betw. centers 10.000 kgs Spindle bore 100 mm Movement slide ( max. ) 1000 ( + 750 ) mm crossslide 630 mm toolslide 200 mm 18 Speeds 5,6 – 280 rpm Motorpower 45 kW Total power 55 kVA Machine weight total ± 18000 kgs Accessoiries 4 chuck facingplate of Ø 1250 mm Condition Machine is in very good condition
used
I. Working capacity -Faceplate diameter 2000 mm -Workpiece max. diameter 2200 mm -Workpiece max. height: -under the cross rail 1850 mm -Workpiece max. weight 20 tons II. Movable cross rail : - Stroke on the column 1600 mm - Rapid moving speed 400 mm/min - Slow moving speed 10 mm/min III. Faceplate main drive in the turning mode. -Main drive motor power 60 kW -Faceplate speed range 250 rev/min IV. Working support: -Ram stroke (Z axis) 1500mm -Ram section 250x250 mm -Ram/taper ISO 50 -Tool magazine, tool number 16 (left tool magazine with milling tools and right tool magazine with turning tools or mixed) -Milling shaft drive motor power 37 kW -One tool holder max. Weight 30-70 Kg -Milling spindle speed 1 - 2000 rev/min V. Feeds -X, Z axes working feeds 1 – 6.000 mm -C – axis feeds (faceplate-milling mode) 0,001 + 2, 7 rev /min -Rapid feeds 10.000 mm/min ...
used
Facing lathe DP 800
used
Type DP 4000 Special facing lathe which has been converted to Siemens CNC for making internal conical threads!! Chuckdiameter: 3700 mm Siemens 840D Thread inserts are included, these are used to test if the thread has been correctly turned on the workpiece.
used
Circumferential diameter above bed ... 1250mm Top width ... 460mm workpiece weight ... 1600kg Face plate diameter ... 1000mm Main engine power... 18.5kW Machine weight ... 6500kg The machine is in good condition, possible to test under electricity.
used
Manufacturer: WMW Type: DLZ 630x2500 E IV Stock number: 0979 Year of construction: 1965 Turning length: 2500 mm Orbit diameter over bed: 630 mm Speed: 1455 rpm Voltage: 380 V Motor power: 10 kW Dimensions (LxWxH): 4800 x 1900 x 1750 mm Machine weight: 4.85 t
WMW Niles DLZ Ø 630 x 2000 mm Distance between centers: 2000 mm Swing over bed: 630 mm Swing over cross-slide: 400 mm Swing in gap: 720 mm Diametre of main spindle bore: 72 mm Power on main spindle: 19 kW Number of speeds: 28 > 1400 rpm Total power needed: 220V Weight: 4,8 ton
used
Face plate diameter: 1.250mm Center height above foundation slab: 1,250mm Weight: 19t Power: 55Kw Max. torque on the face plate: 31,500Nm Maximum workpiece mass between centres: 16,000 kg Speed range: 2.24 – 224 rpm
used
Parallel Lathe WMW NILES type DLZ 500 IV L 1000 Between points: 1000 mm Maxi Ø on bench: 500 mm Maxi Ø over saddle: 300 mm Spindle diameter: Ø 50 mm Spindle speed: from 28 to 1400 RPM 3-jaws chuck Ø 200 mm Threadings: Metric + Whitworth Tailstock CM4 Auto Feeds transverse + longitudinal + rapid Lubricant pump Voltage: 380 V Dimensions (L x W x H): 3000 x 1400 x 1500 mm Weight: approx 2,5 T
used
Key data: 5000 mm, 4000 mm, 22000 mm
Flat top lathe with plate frame (heavy duty lathe) - Machine was overhauled in Italy in 2014 and stored directly - new electrics (control cabinet, cabling) - Max. turning diameter over the bed carriage 4000 mm - Max. turning diameter 5000 mm - Max. turning length: 22000 mm - Face plates speed range 0.9 - 56 1/min - Face plate diameter 4420 mm - Main motor power 30 kW - Max. torque at face plate 61803 Nm - Max. workpiece weight between tips: 20 t - Max. workpiece weight flying: 12.5 t -two bed slides with 4500 mm swivel length - complete with panel panels - a roller trestle - a tailstock After the overhaul, the lathe was no longer put into operation, but stored directly. The machine is dismantled and stored dry in a hall near Hamburg. The machine can be viewed by appointment. The machine is loaded free of charge with an indoor cran ...
used
Key data: 1800 mm, 3000 mm
Center width: 3000 mm Rotation diameter: 1800 mm above bed / 2800 mm above floor Workpiece weight: 8,000 kg max. Jaw chuck: Ø 1800 mm Speed range: 1.8 - 180 rpm. Spindle passage: 220 mm 3-Axis Digital Readout: Easson ES-14 Equipped with: - Motorized tailstock - Various tooling -Operating instructions Country of origin: Germany Engine power: 34 kW Machine weight: 21.000 kg
used
Key data: 355 mm, 1600 mm, 355 mm
Manufacturer | Manufacturer: WMW Type | Type: DLZ 355 x 1600 Stock number | Stock Number: 1009 Turning Length | Turning length: 1600 mm Circumferential diameter over bed | Swing diameter over bed: 355 mm Spindle bore | Spindle bore: 35 mm Tip Height | Center height: 180 mm RPM | turning speed: 112 - 2500 rpm Engine Power | Drive power: 5.5 kW Weight Machine | Weight of machine: 2,2 t
used
diameter range 3-10 mm cutting length 2000 mm speed - meters/min 22-71
used
MAX DIAMETER 1500 MAX MODUL 15
used
Turning tool, special accessories WMW TGL 30-1201 ( TGL30-1201 ) Dimensions: 185 x 120 x 55 mm
used
Turning tool, special accessories WMW TGL 32680 ( TGL32680 ) shaft: Ø 20 mm Adapter: Ø 8, 10, 12 mm Dimensions: 185 x 120 x 55 mm
used
Thread cutting head with chaser jaws, thread cutting stock, Tapping machine, pipe thread cutter -Inch thread: 1/2 - 3/4 inch -Weight: 6 kg
used
max diam 250 , max modul 5
used
Thread cutting head, thread cutting chuck, thread chuck, tap chuck, milling tool, thread cutting apparatus -Manufacturer: WMW, self-opening thread cutting heads type A2 13 pieces -Size: M16 x 1.75 recording MK3 2 pieces -Size: M10 x 1.5 1 piece -Size: Ø 17 mm 10 pieces -Price/tax: complete -Transport dimensions: 400/250/H270 mm -Weight: 22 kg
used
Thread cutting chuck, thread chuck, tap chuck, milling tool, thread cutting apparatus -Manufacturer: WMW ABW, tapping chuck holder MK3 -Type: GB3 -Bore: Ø 24 mm -Dimensions: Ø 80 x 264 mm -Weight: 3.7 kg
used
Thread cutting chuck, thread chuck, tap chuck, milling tool, thread cutting apparatus -Manufacturer: WMW, tapping chuck holder MK2 -Type: A2 MK2 -Bore: Ø 13 mm -Dimensions: Ø 70 x 267 mm -Weight: 3.3 kg
used
Thread cutting chuck, thread chuck, tap chuck, milling tool, thread cutting apparatus -Manufacturer: WMW, tapping chuck holder MK2 -Type: A2 MK2 -Bore: Ø 12 mm -Dimensions: Ø 70 x 267 mm -Weight: 3.3 kg