We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
Arburg 320M 750-90 Year of construction: 1996 Injection unit: Screw diameter: 25 mm Injection weight: 26 g Injection pressure: 2500 bar Dosing volume: 31 ccm Clamping unit: Clamping force: 75 t Tie bar spacing: 320x320 mm Size of clamping plates: 490x490 mm Ejector: hydraulic Clamping unit: hydraulic Control: MULTRONICA Additional equipment: Air valve x 1 It is possible to set the injection unit vertically It is possible to change the screw diameter for fi 20, 30, 35 mm Metrics: Weight: 2360 kg Length/Width/Height: 4.24x1.90x2.05 m Drive: Pumps/motor: 15 kW Heating capacity: 4.6 kW Total power: 19.6 kW All offered machines are started by our service tec ...
Connected load: 37kW. ...
Connected load: 40kVA. ...
Heating output: 5.5kW, connected load: 16.5kW, weight: 2.61t. ...
Arburg 320M 850-210-210 / 2K machine Year of construction: 1992 Injection unit: Screw diameter: 25 mm Spray weight: 62 g Injection pressure: 2950 bar Dosing volume: 73 ccm Clamping unit: Clamping force: 85 t Tie bar spacing: 320x320 mm Size of clamping plates: 490x490 mm Ejector: hydraulic Clamping unit: hydraulic Control: MULTRONICA Additional equipment: Euromap 12 Robot Interface Air Valve x 7 Hydraulic core pull x 2 Injection unit hardened - Bimetal Screw diameter in vertical injection unit: fi 25 mm Metrics: Weight: 3010 kg Length/width/height: 0x0x0 m Drive: Pumps/motor: 22 kW Heating capacity: 8 kW Total power: 30 kW All offered machines are st ...
Clamp force: 750kN, heating output: 11kW, weight: 3t. ...
Description: serial number 137300 Closing force 750 KN Size of mould platens 490 mm x 490 mm Distance between tie bars 320 mm x 320 mm Mould opening stroke: 375 mm Mould height min.: 250 mm Max daylight: 625 mm Hydraulic ejector - stroke: 150 mm Ejector force forward/backward: kN Screw diameter: 40 mm Ls/D ratio: 15 Injection pressure 1150 bar Stroke volume: 188 ccm Shot weight, PS: 158 g Injection rate: 201ccm/s Injection stroke: 150 mm Nozzle pressure: 72,3 kN Nominal capacity of pump motor: 15 kW Installed heating capacity: 5,56 kW Adjustable barrel heating zones: 3 + 1 Dry cycle time: 2 sec Reservoir capacity: 220 ltr. Operating voltage 420 V, 50 Hz Heating 5,56 k ...
Arburg Injection Moulding Machine Type: 520 C 2000-675 Control: Selogica Built: 1999 Closing unit Clamping force t: 220 Opening path mm: 900 Holm size mm: 520 x 520 Installation height min/max mm: 250 Plate size: 715 x 715 Spraying unit Screw diameter mm: 60 Spray weight gr: 427 Spray volume cm3: 508 Spray pressure bar: 1400 Dimensions and weights Dimensions LxWxH m: 5.6 x 1.7 x 2.2 Machine Weight Kg: 7050 Other - Clamping force increased to 220 KN - resistant plastification unit - 2x core pull - Robotinterface Euromap12
ARBURG injection moulding machine Type: 420 V 800-150-150 2Component, with turntable controller: SELOGICA year: 1998 Clamping unit Clamping force t Gap between 80 mm: 500 Holm dimension mm: 420 x 420 min/max height mm: 250 Plate size: 545 x 545 Injection unit Screw diameter mm: 25/25 Injection weight gr: 49/49 Injection volume cm m³: 54/54 Spray pressure bar: 2500 Dimensions and weights Dimensions Lxwxh m: 4.7 x 1.7 x 2.1 machine weight kg: 5000 Miscellaneous 2 Component with turntable (with turntable)
Manufacturer/manufacturer: Arburg Typ/type: 420 C 1300-350 Year/year: 2008 Control/controller: Selogica Clamping force/clamping force: to 130 Holmabstand/Dist.Betw.Tiebars: 420 x 420 mm WZ height/mould hight: min 250 mm Opening/opening stroke: 500 mm Plate distance of max/Max open daylight: 750 mm Auger/screw size: 45 mm Stroke volume/shot volume: 230 ccm spec. Spritzdr / injection pressure: 1670 bar General / General engine power: 22 kW Heating/heating power: 8 kW Dimensions/dimensions: 4.3 m x 1.6 m x 1.8 m Weight/weight: 4300 kg