Fabbricante:
(Categoria: 209)
Cippatrice per legno Macchina silenziosa a bassa velocità con cassetto pressa WL12/30 Dimensioni tramoggia 1200x1200 Diametro dell'albero 368 mm 58 lame di taglio su due file Filtro da 15/20 mm Motore principale 30kW Peso circa 3200 kg
Impianto di smistamento della lunghezza Impianto di smistamento del legname segato MAYRHOFER 5-Scatole Lunghezza totale: circa 22 metri Corrente: 1. Scatola: 1 metro 2° box: 1,5 metri 3. Scatola: 2 metri 4. Scatola: 2,5 metri 5. Scatola: 3 metri buone condizioni - perfettamente funzionante - può ancora essere visualizzato durante il funzionamento Località: Austria, vicino a Graz
Diametro massimo 485mm Lunghezza minima 1500mm, Lunghezza massima 5500mm Potenza dell'azionamento dal disco del rotore 315kw Separatore di fase di alimentazione, nastro di alimentazione, metal detector Rimozione Bruks 2x viti 1x 600x6.500mm e 1x 800x9.500mm Lunghezza trucioli di legno 25mm Armadi Anno di costruzione/messa in servizio 2004 Ore di lavoro circa 12500 ore Capacità 80-100 Qm3/h
Spaccalegna idraulico, funzionale Dettagli su richiesta
Cancello completo Esterer SS45 era generalueberholt Passaggio 450 mm 340 upm 500 Hub con appeso completo, saegen blaetters e Modelli con sollevamento a rullo idraulico con cuneo potenza di azionamento 30 kW con unità idraulica con armadietto di controllo completo
Alimentatore Roundwood a 4 filate con il depositante M'hringer Dimensioni: Copertura in legno rotondo lunga 6,00 metri, larga 6,00 metri Inserire 6,00 metri di lunghezza, 1,50 metri di larghezza il sistema è a 4 fili edter con motori elettrici e unità idraulica
Specifiche Ruwac WS 2220 M: Potenza di aspirazione: 2.400 watt Potenza dell'aria: 290 m3/h Tensione: 230 volt Vuoto: 210 mbar Filtro tasca: 1.2 o 2.6 m2 Volume del contenitore: 35 litri Filtro antipolvere residua: 3,2 m2 Livello di pressione sonora: 67 dB(A) Connessione di aspirazione: 50mm
COMPLETE HIGHSPEED SAWMILL LINE (capacità 80 000 fm):__________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ___________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ _______ ______________________________________________________________________ ______________________________________________________Sistema ...
Vendo essiccatore ad ombrello in Bisonte, produzione 5 t/h, con termostufa da 6mW con alimentazione automatica e fllor mobile autopulente. Con tutte le attrezzature necessarie, ciclone, camino e ventilatori. Prezzo 110.000,00 EUR IVA esclusa. +38765812388 Neven
In vendita trituratore rinnovato realizzato da HOMBACK con 250kw. Utilizzato per triturare il legno in truciolato a lunga conservazione.
Drum crusher with hydraulic pusherKnife drum width: 800 mmMouth 800 x 1200 mmMotor: 18,5 kWextraction connection diameter 200 mm
Max working width: 1300mmMax working thickness: 140mmMax. machining width: 1300mmMotorized feed rollers2 brushing units
Workpiece thickness: 8 - 50 mmEdge thickness: Coil edges 0.4 - 3 mmFeed speed 10 m/minEquipment:manual height adjustment.Joint milling unit, 2 motors Panel edge heatingGluing area Pressure zone 1 driven and 2 non-driven rollersEnd trims, 2 x 0,8 kW motors, straight and chamfer 15°Top and bottom trimmingProfile scraping unit for PVC edgingGlue scrapers
Panel thickness: 8 - 50 mmThickness of the edges: 0,4- 3 mmFeed speed 8 - 11 m / minPU pressure rollersEquipment:Squaring unit, 2 motors 2,2 kWPanel edge heatingEdge magazine for coil and stripsHot melt application with rollerAirtec AT4510 unitThe Airtec aggregate is positioned so you can use Airtec or the standard glue potMotorized side pressure unitEnd trims, 2 motors, pneumatic positioning straight and with chamfertrimming unit above / belowContour trimming unitProfile scraping unitGlue scraping unitPolishing unitDetergent spray systemcentral lubrication
Fixed side at the leftFeedspeed 18 - 25 m/minWorking width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mmPanel overhang 30mmPanel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations)Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mmCoil diameter 830 mmEquipment:Sprayers release agentSquaring device with 2 motors each 3 kWEdge heatingEdge magazine for 2 coils, guillotine for edges up to 3 mmGlueing part A20 with quickmelt applicationLateral pressure zone K, 1 driven and 6 after pressing rollersEnd trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kWContour trimming, 2 exchange unitsProfile scraping PN10Flat scrapers FA11Sprayers cleaning agentBuffingAutomation package straight/chamfer:-Automatic adjustment infeed fence-Automatic setting of pressure rollers-Pneumatic setting of end trims-Pneumatic setting of rough trims-Automatic setting of chamfer/ra ...
Single sided edge bander with hot melt, fixed side at the right, pre-milling unitEdge thickness: 0,4 to 12 mmWorkpiece thickness: 8 - 60 mmFeedspeed 8-20 m/min (limited to 10 m/min using the contour trimming)Workpiece transport by chain, top pressures with rubber rollersSound enclosure over all trimming motorsEquipment:Adjustable fencePre-milling with 2 shapers, each 2,2 kWCoil and strip magazine Hot melt unit, Quickmelt type Pressure zone with1 driven and 2 non-driven pneum. Loaded rollersEnd trims, 2 x 0,35 kW motors, straight and chamfer 15°Top/bottom trimming, motors 2 x 0,35 kWRadius trimmmingContour trimming unit, leading and following edge, 2 x 0,35 kWRadius scraping unitGlue scrapersBuffing unitControlls PC 20+
Workpiece thickness: 8 - 90 mm, electronically adjustableFeed rate: 18-32 m/min frequency controlledEdge thickness: 0.3 - 3 mm for roll edges, strips up to 20 mmEquipment:Inlet guide automatically adjustable via the control, extension 500 mmJoint milling unit: 2 x 3.0 KWworkpiece preheatingGluing unit A34edging magazine for rollPressure zone with 1 driven, 6 non-driven rollers, automatic adjustment from the controlCutting unit WK14, straight, 2 motors 0.8 kWPre-milling unit: 2 x 1.5 KW, pneumatic adjustmentForm milling unit FF 12 automatic, 2 motors 0.4 kWradius/phase milling unit FF12 automatic 4 motors 0.4 KWuniversal milling aggregate controlled UF11, 4 kWProfile scrapers PN20Glue scrapersNozzles for detergent and anti-stickPolishing unitControl: Power Control PC22
Fixed side at the leftFeedspeed 18 - 25 m/minWorking width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mmPanel overhang 30mmPanel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations)Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mmCoil diameter 830 mmEquipment:Sprayers release agentSquaring device with 2 motors each 3 kWEdge heatingEdge magazine for 2 coils, guillotine for edges up to 3 mmGlueing part A20 with quickmelt applicationLateral pressure zone K, 1 driven and 6 after pressing rollersEnd trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kWContour trimming, 2 exchange unitsProfile scraping PN10Flat scrapers FA11Sprayers cleaning agentBuffingAutomation package straight/chamfer:-Automatic adjustment infeed fence-Automatic setting of pressure rollers-Pneumatic setting of end trims-Pneumatic setting of rough trims-Automatic setting of chamfer/ra ...
Fixed side at the leftPanel thickness min/max: 16/45 mmMin. panel width: 150 mmLateral panel support for panel width up to 900 mmMin/max. panel length: 700 / 3100 mmMax. laminate overhang: 110 mmMax. laminate thickness: 0,8 mmRadius min/max: 6 / 22 mm (depends the laminate)Feedspeed max. 18 m/minTop pressure by beltEquipment:Infeed fence, adjustable, defines the panel overhang2 x trimming unit 0,4 kW, HSK 25 toolholder1 x PVAc glue application5 x glue nozzle, adjustable1 x hot air blower3 x IR heating on top (55 cm length), 3 x bottom (90 cm length)Postforming zone 1,8 m. lengthVarious pre-installed profiling sets 1 x top trimmer 0,4 kW
Machining center in vertical design with automatic returnWorkpiece dimensions:Length: 200 to 3050 mmWidth: 50 to 1250 mmThickness: 8 to 80 mmweight max 60 kgPerformance- 2x vertical drilling unit separately controllable with variable speed. right left V10/32mm. 2.3 kW. Drill length 70 mm, D= max 35 mm- 2x horizontal drilling unit, 6 spindles in X direction, variable speed. right left can be controlled separately. Drill length 70 mm, D= max 20 mm- 2x horizontal drilling unit, 2 spindles in Y direction, variable speed. right left can be controlled separately. Drill length 70 mm, D= max 20 mm- Grooving saw unit X-Y can be swiveled 0°/90° saw diameter 125 mm, rpm 1500-7500 frequency controlled- Dowel insertion station for automatic insertion of dowels on the two transverse workpiece edges 1x left side / 1x right side glue pump, vibrating guide for dowels 8 x 35/40 mm- plausib ...
4-axis machining centerworking area: X Y Z : 3060 x 1080 x 155 mmMovement speed X 100 m/min, Y 100 m/min, Z 30 m/min14 vertical spindles4 horizontal spindles in X direction2 horizontal spindles in Y directionGrooving saw 0° - 90°toolchanger 7 positionstoolchanger 10 positionsRouter 7,5 kW, ISO 30 , 1000 - 24000 r/min, c-axislock milling aggregate available in option
Gantry-type, 3-axis CNC machining centreWorking area (type 2132): approx. 3300 x 2100 mmVacuum table with multiple switchable zonesInput: AES lifting table for automatic sheet loadingOutput: conveyor belt with label printer (labels are printed and applied manually)Main spindle: HSD ES929, HSK-F63 mount, 7.5 kW (9 kW), speed up to 24,000 rpm, 800 Hz, 380 VMain spindle overhauled in 2023Drilling unit with 16 spindles: 6 vertical spindles in X, 4 vertical spindles in Y, 2 double horizontal spindles in X, 1 double horizontal spindle in YSlotting sawTool changer with 12 positionsVacuum: Becker vacuum pumps, system approx. 500 m³/hControl: OSAI control system with AES ProcessController, operation via console with touchscreen and keyboardOperating hours: approx. 2,100 h (machine life), main spindle overhauled at approx. 1,360 h
Working area: X 5005 x Y 1520 mm x Z 200 mmMain spindle travel: X 5910 mm, Y 1815 mm, Z 655 mm.Travel speed: X 80 m/min, Y 80 m/min, Z 25 m/min8 workpiece consoles with automatically positioning vacuum cupsEquipment:Drilling unit with 19 spindles, 7 vertical spindles in X, 6 vertical spindles in Y, 2 double horizontal spindles in X, 1 double horizontal spindle in Y Slotting sawMilling motor 12 kW, 1000–24,000 rpm, HSK-F 63 mounting, liquid-cooled, 5-axis controlledTool changer with 22 positions Vacuum pumps with 2 x 100 m³/h capacityPC controlMasterwork software Integrated waste conveyor
Bridge type Capacity for all units: 3300 x 1100 mm(alternating: 2 x 1025 x 1100 mm)Capacity for routing with tooldiameter 25 mm: 1550 mmWorkpiece thickness up to 300 mm (stroke Z-axis 600 mm)Speed in X and Y: 60 m/min, Z: 25 m/min, Vector: 85 m/min6 Support rails with LED positioning indicationVacuum: 100/140 m3/hControlls: Powercontrol PC85Waste/chip removal belt in machine baseMachine pneumatically prepared to take pneumatic clamps, 3 pcs clamps includedDrilling unit V9/H4, 13 spindles, motor 2,2 kWMain spindle DRIVE5C+, 5-axis, 10 kW, HSKF63 taper, speed 1000 to 24000 r/min, tooldiameter up to 180 mm for routing, 350 mm for cutting14-fold rotary toolchanger and pick-up place for a sawbladeWoodwop software
Working field: axis x: 3200 mm, axis y: 944 mm, axis z: 110mmMax programmable speed: axis x: 100 m/min, axis y: 75 m/min, axis z: 15 m/minDrill holder: diameter 10 mmSpindle speeds: 4000 rpmGrooving saw: diameter 120 mmDrill spindles: 24 horizontal spindles in X,10 vertical spindles in X lineWorking pressure air pressure: 6 barInstalled power: max 25 kWCapacity of vacuum tools: 40 m³/hCNC:screen: monochromatic 9”Floppy disk unit
Working area: X 5200 x Y 1260 mmHeading of main spindle: X 5709 mm, Y 1650 mm8 workpiece consolesEquipment:Drilling unit with 18 spindles, 12 vertical spîndles, 6 horizontal spindles (4 in direction X , 2 in direction Y )Grooving sawMilling motor 11 kW, 20000 rpm max, HSK-F 63 take-up, liquid-cooled, 5-axis controlledTool changer with 16 positionsLaterally positioned changer with 8 positions PC control
Working field: axis x: 2310 mm, axis y: 628 mm, axis z: 90mmMax programmable speed: axis x: 100 m/min, axis y: 75 m/min, axis z: 15 m/minDrill chuck: diameter 10 mmSpindle speeds: 4000 rpmGrooving saw: diameter 120 mmDrill spindles: 4 horizontal spindles in X,12vertical spindles in X lineWorking air pressure: 6 barMax consumption of compressed air: 0,75 NL/cycleInstalled power: max 7.5 kWCapacity of vacuum tools: 40 m³/hCNC:screen: monochromatic 9”Floppy disk unitPLC for control of the machine cycle
X=3700mm Y=1440mm, Z=150mmMoving speed: X: 80 m/min, Y: 80 m/min, Z: 20 m/min8 supports with vacuum cups, pneumatic clamping8 fences at the rear8 fences in front2 left fences and 2 right fences6 rails for panel loading with pneumatic liftingPositioning the vacuum cups using a laser1 connection for templatesVacuum pump with flow rate 100 m3/hConfiguration V25,H8X/6Y, N1 X-Y 90°, F1-HSK63-15KW,F1-HSK63-9KW, C axis, W14 rearMain motor 15 kW, 1250-24000 rpm, air-cooled, 360° C-axis, C-axis interpolation axis, HSK 63 mountingC axis extension for flex-5 aggregateMain motor 9 kW, 1250-24000 rpm, air cooled, HSK 63 mountingTool changer operating in X direction with 14 positions, rear mounted2 x 4 vertical X drilling pins, 2 x 3 vertical Y drilling pins14 horizontal drilling spindles90° groove saw X-Y directionPC 85 power control software with:Woodwop: workshop-oriented programming systemImpor ...
