used CPM pelletizing presses

Freshly Revised Koller to CPM Press 3022 or 7022 , Fshbone, 2 new bearings, new sleeve, new intermediate ring, filled with grease. rest used. Koller are no longer needed due to machine changes. 3 pieces Available

Collier sleeves Fishbone CPM 16-2.5

Collier sleeve Fishbone CPM 22-2.5 for pellet press

Freshly revised Koller to CPM Press 3022 or 7022 Punched, 2 new bearings, new sleeve, new intermediate ring, filled with grease. rest used. Koller are no longer needed due to machine changes. 3 pieces Available

For sale complete plant for wood pellet production, made from CPM, capacity 6t/h. A most of the maschines from line are produced in between 2008-2010.y., except presses for making pellets (its bit older then rest of the line, but completly renewed before restarting. Line is consisting from: 1.Chain conveyer for logs transport. 2.Lift with angle platform for dosing material. 3.Entrance belt transporter with magnetic section for detection of iron. 4.Grinder (hammer mill) BRUKS 500kW 5.Verticaly basket transporter for chip wood. 6.Horisontal belt transporter for chip wood with three side ejectors into depoos (separated with type of the wood) 7.Hidraulic floor platform for dosing wood chips (three pcs.) with all instalation and system of hidraulic pistons. 8.Horisontal belt transporter for transportation material on drying. 9.Repler transporter for driving wood chips into fire plac ...

Complete pellet line for biomass or animal feed. CPM 3020-4 with 132 kW motor Including CPM Conditioner, CPM press and Geeelen cooler with fan and cyclone. Positive direct gear drive 132 kW, provides a 98% energy transfer Rounded cast gear case with internal ribbing for quieter operation Segmented die clamps for quicker die changes Metal-to-metal seals between components Modular gearbox design for production flexibility Replaceable quill flange Stainless steel pellet chamber Single motor 132 kW for greater efficiency Very good condition.

Used SHREDDIES production line Manufacturer: CPM WOLVERINE PROCTOR Ltd. Model: 5-station SHREDDIES production line Year: 2016 Description: A five-line production line for multilayer flakes from crushed grains. Finished product capacity: 700 kg / h Line speed: 54m / min. Finished product density: 200> 220 g / l Overall dimensions and setting of the machine: length x width x height: approx. 10929 x 1600 x 4685 Design diameter of the grinding roller: 203 mm Design working width of the chopping roller: 210 mm Rotational speed of the grooved roll: 20-85 m / min. Design number of positions: five (four working, one spare) Design width of cutting station conveyor: 230 mm Nominal design width of the edge trim: 12 mm per edge, total 24 mm Design product size: approx. 25 x 25 mm Technical data: Dimensions (length X width X height): Power supply: 400 V, 3 phases, 50 Hz Control v ...

Jetzone furnace Manufacturer: CPM WOLVERINE PROCTOR Ltd. Model: SND 1.5 x 202 Year: 2016 Productivity: 450 kg / h Dimensions: 8136 x 3581 x 4376 Heating medium: natural gas Description: A high-speed dryer consisting of two main elements: a fitting equipped with heating and distribution elements, and a production conveyor.

2 pcs clamping jaws 22" / Die Clamp Segment Assy 22" for pellet mills CPM 7722-2 and CPM 3022-2 Plus Transportation

Assembled Knife Holder for CPM 7930 Model 30-4 Knives included

Water flow rate 30-150l/h Flow meter with manual control valve Solenoid valve for water and compressed air. Pressure regulators for water and air Special nozzle for injecting water and air Mounted on a plate

* General * SKU303P611 * LocationBarneveld * MakeCPM Wolverine Proctor (UK) * TypeVariable circulation lab dryer * No.L 09091 * Year of construction2009 * Main Features * MaterialStainless steel * Volume900 Ltr. * Max.temp.250 °C * Specified Features - Drying oven * Drying ovenvariable circulation laboratory dryer * Max. temperature250 degr.C * Number of compartments:1 * Capacity900 Ltr * Internal width800mm * Internal depth1030mm * Internal height1100mm * Steam heatingcheck * Number of doors:2 * With air circulationcheck * With fan(2x) * Motorcirculation fan 2,0 KW, Motor exhaust fan 3,0 KW * With air humidificationcheck * With trays(4x) 762x508x102 28% perforated * MaterialStainless steel * Information * With switchgearcheck * Weight2000 KG * CEcheck * Floorspace2,8x2,2 M * Extra Specificationsheat exchanger : Heap Dawson Limited, Serial 6744, PS 10 bar, max 250 degr.C. Drying ovensC ...

Pellet mill / press CPM 7900 aftre renovation Dia inch : 30 - 762 mm Die width : 8 - 210 mm Die surface 5025 cm² KW : 250 KW Machine type : 7900 Buildyear : 1984 Width rollers : 215 mm Dia rollers : 350 mm 1 set rollers Oil cooling Twin mixer 2 x 15 KW / Die Hosting system New inlet in stainless steel

Graf Kollerhülsen Geriffelt to CPM Pelletpress

Graf Koller sleeves punched for CPM 16-2.5 Pelletier press

Koller sleeves Geriffelt for CPM 22-2.5

Koller sleeves punched for CPM 22-2.5

L 22 Kw POWER 330 Kg/h (material-dependent/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSING SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for the wood chip raw material - Pellet mill with main motor 22 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system for controlling the clogging of the matrice Moisture monitoring - Cooling and dedusting system for the pellets produced via a screw

l 90 kw POWER 1350 kg/h (depending on material/full load) Active process and computer-controlled Koller PP 500 is a pellet line consisting of the following machines: - DOSAGE SYSTEM with an automatic PLC control of the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for wood chip raw material - Pellet mill with main motor 90 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system to control the blockage of the Matritze Humidity monitoring - Cooling and dedusting system for the pellets produced via a screw

This press from Collin at Plastima Used Machinery in machine storage. The machine is from 2001 and is in good condition. – Brand: Collin Pilot & Lab Solutions – Model: P200P – Construction year: 2001 – Plate Size: 200 x 200 Mm – Max. pressing force: 196 kN

Stock - No.: 2166 1 used, in 2019 partly overhauled and tested film/foil/regrind pelletizing extrusion line EREMA type RGA 50 T equipped with: 1. cutter / densifier unit, new motor with 18,5 kW tangential ( T ) cutter - Ø 550 mm 2. Extruder single-screw Ø 50 mm – 20 LD motor 18,5 kW – NEW Frequency Converter 3. screen pack changer sieve- Ø90 mm with hydraulic unit-new 4. watering-granulation unit HG, pelletizer drive 0,75 kW 5. pellet drying vibrating dewatering unit GS 1000/200 6. control board ( new converter ) The line is ready for operation, date shortly in our workhsop Wuppertal-Germany. More regranulation-pelletizing lines ex stock available, ask for our actual machine-list or visit us

We can offer you all types of Wafios nail machines from S25 - N90

We can offer you all types of Wafios nail machines from S25 - N90

Stock number: UG5830 Used chamber filter press by FILTRI DIEMME model GIGANTE 1500. Frame type 1500 mm x 1500 mm /90. Press has 85 pp plates with bottom feeding inlet. Filtration surface about 321 m2. Press is equipped with control panel, Willet sludge pump designed for work on pressure 10 bar, polymer dosing system, cake washing system, photocell safety system. Plates designed for work on pressure up to 15 bar. Closing pressure 385 bar. Dimensions: length 10 m x width 2 m x height 2 m. Reported output up to 30 m3 of sludge per hour.

with rotary tower for sieve-edge presses (except EBP350) For cleaning and grinding fruit. The pre-washing system is an absolute must for the hygienic processing of fruit. Thanks to the built-in ratz mill with interchangeable sieves, you get the ideal mash consistency for the respective pressing method. Technical data: Rated power up to 6 000 kg/h Power: Elevator 2.2 (3.0) kW (PS) Mill 5.5 (7.5) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical protection 16 A Dimensions: Length 1 750 mm Width 870 mm Height 2 700 mm Delivery or insertion height 800 mm Weight 420 / 450 kg Material 1.4301 / AISI 304 Connections: Connection for cleaning 1/2" inside Connection for washing container 2" outside Height mash ejection 1 730 mm / with transition 1 510 mm can be used for core fruit Scope of delivery 7, 9 and 12 mm cutting sieve