used DUNKES Hydraulic Open Gap Presses

Two-hand and foot operation Pressing force: 1000 kN Projection: 380 mm Stroke: 650 mm Distance table/plunger, gr. stroke top, verst. above: 950 mm Ejector with end position damping on both sides Ejector travel: 150 mm Ejector force: 160 kN Pressure piece hardened: Ø 98 mm Table surface: 720 x 630 mm Total weight: 7,400 kg

Key data: 10 t, 300 mm, 510 mm

Table 470x460 , installation height 605

Hydr. High-speed single-column press Fabr. DUNKES type HZS 40Machine -No: H 77-581, built in 1981Press force: 40 tOperating pressure: 270 barStroke: 150 mmInstallation height: 400 mmOutreach: 280 mmRapid traverse: 400 mm / sec.Rapid traverse to: 400 mm / sec.Pressing under full load: 14 mm / sec.Table height: 820 mmTable surface: 600 x 515 mmDiarrhea hole in the table: 100 mm Drm.Drive power: 7.5 kWWeight: 3.1 tOil filling: 230 lExternal dimensions: 850 x 1200 x 2390 mmWith- Cutting impact damping- Safety 2-hand control- self-holding with rapid traverse shutdown- Electric return stroke limitation- Setup tip circuit- Fully automatic workflow- Emergency stop switch- stepless force preselection- graduated Adj. mech. depth stop- Switching in the lower stroke rangexa0xa0xa0 Lift and time changeoverxa0xa0xa0 Lift and pressure changeover- separate hydraulics for drawing cushionsused, in good co ...

Pressing force 160kN,pull cushion force 63kN,stoesselstroke 300 mm, pull-cushion stroke 150 mm, recessed height 500 mm, table 630x400,Stoessel 300x250,pull cushion flap 350x270,

Capacity: 0 t Table length: 0 mm Table width: 0 mm Stroke: 0 mm CNC Brand: 0 CNC Model: 0 Operating hours: 6044 Technical data Pressure: 40 to Pressure: 400 kN Pressure: 260 bar Total stroke: 300 mm Execution: 4 columns Table surface: Length: 650 mm Width: 650 mm Min. stroke: 33 mm/s Max. stroke: 120 mm/s up: 450 mm/s Oil quantity: 300 l Voltage 50 Hz 3x: 380 Volt Motor power: 15 kW Machine´s weight about: 5200 kg Overall dimensions machine: Length: 1750 mm Width: 1200 mm Height: 3500 mm Various accessories: Security/savety device Ziehkissen pneumatisch: number (steps): 2 Force du cylindre: 30 kN Total stroke: 100 mm

Technical data: -maximum pressing force 40 t -maximum piston stroke 218 mm -Height 410 mm -Projection up to mid slide 280 / 370 mm -Table size 650 x 520 mm -Plunger surface 500 x 400 mm -Stö�elboaufnahme DIN 810 50 mm -Work speed max.bis 226kN 39 mm / s -Min. working speed 21 mm / s -Eilabsenkgeschwindigkeit 428 mm / s -Rear hub speed min. / max. 100 / 420 mm / s -Table height above floor 820 mm -Oil quantity approx. 400 ltr -Drive 400 V / 15 kW -Space requirement approx. B 1400 x H 3200 X 2200 mm -Weight approx. 7000 kg -with: - hydr. PIN voltage -Control CNC 50 - separate control panel

Pressing force: 160 kN Impact stroke: 100 mm Mounting height: 350 mm Hole in the table: 100 mm Pushhole bore: 32 mm Stand passage: 650 mm Table size: 630 x 400 mm Hydraulic pressure: 280 bar electr. Connection: 380 V, 5.5 kW Space requirement: 1550 x 1050 x 2400 mm Weight approx.: 3 t

Capacity: 0 t Stroke: 0 mm Distance column/center (Throat): 0 mm CNC Brand: 0 CNC Model: 0 Technical data Pressure: 1000 (12 Atü) kg Execution: 1 support Table surface: Length: 120 mm Width: 110 mm Max. distance from table to slide: 110 mm Depth of throat: 65 mm Machine´s weight about: 20 kg Overall dimensions machine: Length: 400 mm Width: 150 mm Height: 600 mm Various accessories: Micrometer stop

Technical data Pressure: 1000 (12 Atü) kg Execution: 1 support Table surface: Length: 120 mm Width: 110 mm Max. distance from table to slide: 110 mm Depth of throat: 65 mm Machine´s weight about: 20 kg Overall dimensions machine: Length: 400 mm Width: 150 mm Height: 600 mm Various accessories: Micrometer stop

Conductive force: 63 t Projection: 280 mm Table size: 500 x 600 mm Installation height: without straightening bridge 600 mm stroke: 160 mm Tappet speed upwards: 117 mm/s m/min Rotary speed downwards: 42 mm/s m/min Space requirement: 1600 x 700 x 2400 mm Weight: 3900 kg

pressure: 10 t throat: 0 mm stroke: 400 mm total power requirement: 7,5 kW weight of the machine ca.: 6500 t dimensions of the machine ca.: m D U N K E S (Germany) CNC Controlled Hydraulic Double Column Press Model HD 10 Year 1993 ________________________________________________________ Pressure 10 tons Ram stroke 400 mm Mounting height 600 mm Table size 400 x 300 mm Table height above floor 820 mm Ram area 400 x 300 mm Ram bore 40 mm Quickspeed, downwards, max. 70 mm/s Working speed, downwards, using max. pressure 40 mm/s Working speed, min. 5 mm/s Working speed adjustable from 5 - 70 mm/s Return stroke speed, min./max. 20 / 175 mm/s Drive 7.5 kW Total electrical load, approx. 12 kW - 380 V - 50 Hz Weigh ...

pressure: 25 t throat: 250 mm stroke: 100 mm total power requirement: 7,5 kW weight of the machine ca.: 3200 kg dimensions of the machine ca.: 1000 x 1700 x 2600 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure:2,5 t

pressure: 63 t stroke: 650 mm throat: 380 mm table surface area: 650 x 1000 mm ram surface: 650 x 1000 mm dayligth: 850 mm die cushion stroke: 220 mm die cushion area: 500 x 520 mm die cushion capacity: 25 t ram stroke speed - under load: Vorlauf 400 mm/sec ram stroke speed: Rücklauf 330 mm/sec drawing speed: Auf 220 mm/sec drawing speed: Ab 300 mm/sec working height (floor - top of table): 1050 mm total power requirement: 18,5 kW weight of the machine ca.: 6 t dimensions of the machine ca.: 1,2 x 2,2 x 3,6 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 100 t throat: 380 mm stroke: 400 mm power capacity: 22 kW dayligth: 600 mm ram surface: 600x500 mm table surface area: 720x600 mm weight of the machine ca.: 9 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 63 t distance between columns: 650 mm stroke: 200 mm total power requirement: 30 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 125 t distance between columns: 1050 mm stroke: 250 mm total power requirement: 40 kW weight of the machine ca.: 8,5 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 75 t throat: 280 mm stroke: 303 mm total power requirement: 15 kW weight of the machine ca.: 7000 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Single Stand - Hydraulic Press DUNKES Type HZT 2,5 Masch. Nr. H94-2558 Year of construction 1994 Compressive force 2,5 ton. Projection 180 mm Table surface 420 x 300 mm Diarrhoea opening in the table 60 x 185 mm Ram surface 40 mm Pine bore 20 mm Ram stroke 160 mm Installation height max. 250 mm rapid traverse Down 65 mm /sec. Rapid traverse upwards 160 mm/sec. Working speed 8.3 mm/sec. Table height above corridor 950 mm Hydraulic operating pressure 135 bar Tank capacity hydraulics approx. 100 litres Drive power 1.5 kW Mains connection 400 Volt, 50 Hz - Pressure and displacement cut-off - 2-hand operation on the machine - Stroke counter - UVV 11.064 VGB 7.n.5.2 (for manual insertion work) - 32047 read operating hours Space requirement L x W x H 1100 x 980 x 1950 mm Weight 700 kg very good condition; used

Description: Control conventional / Option: new (Siemens S7-1500F) Stroke: 650 mm Installation height (top stroke): 950 mm Table surface: 800 x 700 mm Drop-through opening in the table: 200 mm Table height above floor: 920 mm Plunger surface: 630 x 600 mm Speed down: 65 mm / s Speed up: 375 mm / s Working speed: 17 mm / s Oil volume 350 Max. pressing force: 100 to, throat: 380 mm, table surface area l x w : 800 x 700 mm, total power requirement: 18,5 kW, weight approx.: 9,000 kg, Approx. Onsite Dimension. (l x w x h): 1,500 x 2,500 x 4,000 mm

pressure:160 t throat:370 mm stroke:150 mm total power requirement:45 kW weight of the machine ca.:22 t dimensions of the machine ca.:2,75 x 1,85 x x 4,80 m rules for accident prevention:Vorhanden work table::1500 x 700 mm Documents:vorhanden

pressure:200 t distance between columns:1650 mm stroke:600 mm distance table/ram, max. stroke up, adjustment up:1200 mm table surface area:1600 x 1250 mm die cushion capacity:80 t die cushion stroke:300 mm die cushion area:1300 x 900 mm table height over floor:800 mm ram surface:1600 x 1250 mm oil volume:ca. 2000 l power capacity:43,0 kW weight:25,0 t Dimensions (WxDxH):2,9 x 2,3 x 5,8 m height beneath floor:0,85 m German Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 § 20

pressure:100 t throat:380 mm stroke:650 mm distance table/ram, max. stroke up, adjustment up:950 mm table surface area:800 x 700 mm hole in the table:200 mm table height over floor:920 mm ram surface:630 x 600 mm speed down:65 mm/s speed up:375 mm/s working speed:17 mm/s oil volume:350 l power requirement:18,5 kW weight:9,0 t Dimensions (WxDxH):1,5 x 2,5 x 4,0 m German Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 §20

pressure:160 t distance between columns:880 mm stroke:150 mm distance table/ram, max. stroke up, adjustment up:400 mm table surface area:830 x 1000 mm hole in the table:265 x 365 mm table height over floor:850 mm side window:610 mm ram surface:860 x 1000 mm power requirement:55,0 kW weight:14,7 t Dimensions (WxDxH):2,2 x 2,0 x 4,3 m German Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 § 20 depth stop:motoric adjustable table:motoric foundation pit:not necessary

pressure:160 t throat:370 mm stroke:150 mm distance table/ram, max. stroke up, adjustment up:500 mm table surface area:1000 x 700 mm hole in the table:100 mm table height over floor:820 mm ram surface:600 x 520 mm speed down:350 mm/s speed up:350 mm/s working speed:12 - 36 mm/s oil volume:1100 l power requirement:27,0 kW weight:16,5 t dimensions (WxDxH):1,8 x 2,7 x 3,95 m German Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 depth stop:motoric adjustable