We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
used
Troester.200mm H/F strainer M/C Number 7175-71 L/D 6.5/1 Roller Feed 350mm. Hinged strainer head with hydraulic clamp. 125KW AC v/s motor. On single bedplate. With controls.
used
Manufacturer: Paul Troester Maschinenfabrik/Hannover Year of construction: 1978, machine was in operation until the end of 2015 Screw diameter: 150 mm Length: 16 D (approx. 2,400 mm) Screw speed: 2.5-25 / 4 - 40 U/Min. Centre height of the extruder: 1,100 mm Type of gearbox 3 TH 990 K / 2s, 2 speeds. Gear ratio: = i1 16.5: 1 i2 = 26.4: 1 Maximum gearbox output torque: 45,000 nm Maximum permissible injection pressure: 350 bar without limitation through the extrusion head. The extruder will be overhauled and designed/changed according to customer's specification. Below pictures 1-4 show an extruder overhauled by us.
used
available Troester Triplex Extruder Top machine QSM 90x 16D Middle machine 200W x 6D Below machine QSM 150 x 16D Head MW500 Description attached!
used
Profile extruder, GE 90 x 16 D vacuum, make Troester, cold lined
used
Key data: 120 mm, 22
Output: approx. 255 - 450 kg/h (manufacturer's information from brochures; depending on material and profile; DEGUMA assumes no liability for actual, product-specific output) Straight head on hinged flange, fastening via screws; NEW SEVA motor, new control system
Key data: 120 mm, 18 , 45 1/min
Screw with vacuum zone, output approx. 255 - 400 kg/h, straight head
used
Key data: 90 mm, 16
available Triplex Extruder- Cold Feed with head and feeder. Description attached!
used
Used rubber extruder make Troester, type GSV 60/k-12-18D-m.S., Execution as desired, with or without vacuum Built in 1991, machine was in operation until the beginning of 2010 Feed roller Kpl. new drive with flat gear motor Screw speed max. 62 rpm. Engine power 22 kW Control with PLC and temperature control new on request Extruder similar to attached photos.
used
Used Troester rubber extruder type GSV 60/k-12-18 D with feed roll can be modified/overhauled according to customer\s specification, with or without vacuum, year of construction: 1991 machine was in operation until end of 2010. including feed roll, new drive with flat-gear motor screw speed: maximum 62 rpm motor power: 22 kW PLC control and TCU can be renewed, if requested.
used
We would like to sell Extruder Bandera T150 and Troester with included feeding line, cooling line and cutting sector. This machine was used for production of Neolite Rubber Sheets. More information upon request!
used
Roller diameter: 550mm, roller width: 1500mm, connected load: 75kW, without documentation, accessories or spare parts, an inspection is possible, the machine was used to process silicones with colors, fillers and other additives.
used
roll surface width: 450 mm roll diam. toproll: 203 mm roll diam. bottom roll: 203 mm output: 8,8 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
screw ø:: für Extruder 90 mm screw length:: -- screw speedl:: -- U/min drive power:: 13,6 kW Condition: little used, as good as new Specification: gear pump ZP 75/50 for extruder size 90 - SEW helical gear units: R 97 - Siemens direct current motor: 1 GG5 118 - Drive power: 13.6 kW, 57 A - curved tooth coupling - With clamp for the head connection, - Clamping flange for extruder and head connection, - Base plate with linear guide rails, - Tooth shaft diameter: 75 mm - tooth width: 50 mm - helical gearing, hardened steel bearings, right-hand drive - without control The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Key data: 550 mm, 1500 mm
Mixing mill Troester 550 x 1500 mm Bush bearings Motor: 90 kW Friction : 1:1,20 Manual NIP adjustment Stock blender
used
Key data: 1800 mm, 700 mm, 700 mm
available Textile Calendar Complete Line - 2 x let-off, Splicing press, Accumulator, Tension unit, Heting Drums, Calender with thickness measuring, Cooling Drums, Thickness meas. (final product), Accumulator, 2 x Wind-up More details in the attachment!
used
Nakata Zoki Kobe, Japan (Troester design) Duplex Extruder Unit Dual 150mm dia PIN Type Extruders, Year of manufacture: 1990, with Roller Feed, and duplex Die. L/D ratio 16:1 Number of Pins: 10 Rows x 8 Pieces, Spare Pins included. Screw Speed 45 r.p.m. Motors 185kw D.C. variable speed, 415 volt, 3ph, 50hz. Full Books and Drawings available. Thyristor Drives included. Starter and Control Panel for Lower Extruder only. Die usable Width 18\\, In good condition.
new
We´re offereing successfully since many years twin-screw compounding extruders >> NEW segmented screws and cylinders, LD ratio due to your request Side-feeders, vacuum ports and accessories Please contact us for further information
used
Key data: 100 , 140
Stock No.2452 1 used, partially overhauled and functionally tested pelletizing line Throughput up to 500 kg/h depending on the material, consisting of: Tamping unit Kreyenborg SW 100, drive 7.5 kW Extruder BKG single screw Ø 100 mm – 35 LD, Drive 132 kW – AC frequency controlled Screw speed up to 143 rpm.-1 screw depth 14 mm Heating capacity approx. 35 kW installed 1x athm. Degassing zone Screen-pack-changer Double piston Kreyenborg K-SWE 160 RS back-flush self-cleaning with screen surface 244 cm² BKG underwater pelletizer AH 300, complete with: Start-up valve incl. Hydraulic station Granulator with drive 4 kW Water pump 2.2 kW By-pass system, water tank with heating 9 kW installed and heat exchanger BKG granulate centrifuge TWE 300 with drive 3 kW pellet classifier table Control board and Siemens material feed conveying, big-bag filling station ...
used
PE 300 plastic recycling and regranulation line was built in China in 2011 by Zhangjiagang Wuhe Machinery Co. LTD. The extruder for plastics used in the processing and manufacturing of various types of materials can produce up to 300 kg of parts in one hour of operation. The complete PE and PP plastic extrusion line includes a compactor, screw, cylinder, conveying system, heating system and temperature control panel. Material production begins by heating the plastic to a maximum temperature of 300°C in the 11 heating zones of the PE 300 granulating line, controlled by thermoregulators. The extruder then presses the material further through a 100 mm diameter screw located in a cylinder with abrasion and rust protection. At the end of the process, the machine head moulds the plastic to give it the right properties and shape. The PE 300 extruder is equipped with thermoregulators with ...
used
Used twin-screw, parallel, counter-rotating extruder by Amut model BA92 NOMAX. New 2011. Output: 270 - 370 kg/h Hours of operation: 53638 h Other details: - Diameter of augers 92 mm - L/D ratio 28:1 - Drive power 60 kW (400V, 50 Hz, 3 ph) AC - Two sets of screws -for ABS processing -for PVC processing - Number of cylinder heating zones 7 - Number of cylinder cooling zones (air) 4 - Number of heating zones for head and adaptor 5 + 1 - Built-in pressure and temperature measurement system for plastic mass - Thermal oil unit for thermostating the worms for PVC - Drive power of vacuum degassing pump 11 kW - Drive power of screw feeder 1.5 kW - Without control (subassemblies available according to the list)
used
1 x Buss PR200? Ko-Kneader, supplied fully refurbished by Buss in 1995, G130 gearbox, 11 L/D ratio, with 340kW dc motor and controls. Including oil heater and TCU 2t/hr output. Spare screw and barrel segments.
used
Barwell C3 Preformer Extruder 2500 psi Output 600kg/hour Ram type Extruder Extruder size 250mm With Rotary Cutter 8 fixed speeds Year 1980
used
Screw diameter: 59mm, screw rotational speed: 25-250/min, with complete documentation, control cabinet, screen changer, side dosing unit, granulator and additional accessories.
1 x Berstorff GmbH 250mm strainer extruder, Year of manufacture: 1988, L/D ratio 7:1, power roller feed (300mm wide), with 120kW, 1800rpm DC variable speed motor mounted on top of gearbox (belt drive), with tube head and knife at top for sheet extrusion. Complete with control panel etc and in very good condition.
used
According to the description below