Alt kategori
(3. kategori seviyesi)
Üretici:
(kategori: 106)
pressure:50 tdistance between columns:1750 mmstroke:500 mmDistance table/ram, max. stroke up, adjustment up:800 mmtable surface area:1700 x 750 mmtable height over floor:800 mmside window:650 x 750 mmram surface:1700 x 750 mmpower requirement:11,0 kWweight:11,0 tDimensions (WxDxH):2,1 x 1,15 x 3,4 mGerman Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 foundation pit:not necessary
pressure:015 tthroat:200 mmstroke:4 - 70 mmno. of strokes:140 /mindistance table/ram, max. stroke up, adjustment up:310 mmtable surface area:430 x 395 mmhole in the table:165 x 160 mmtable height over floor:560 - 735 mmtable adjustable:175 mmram surface:160 x 130 mmram adjustment:80 mmpower requirement:1,2 kWweight:0,9 tDimensions (WxDxH):1,0 x 1,25 x 1,8 mclutch:Drehkeil overload protection in ram:mechanical
pressure:030 tstroke:8 - 40 mmno. of strokes:100 - 600 /mindistance between columns:325 mmdistance table/ram, max. stroke up, adjustment up:250 mmtable surface area:540 x 300 / 325 x 395 mmhole in the table:315 x 110 mmtable height over floor:1000 mmcolumn travel -side:290 mmram surface:250 mmmaterial width of feeder:120 mmmaterial thickness of feeder:3,0 mmfeed length:60 mmpower requirement:5,5 kWweight:2,6 tDimensions (WxDxH):1,5 x 1,2 x 2,2 mclutch:pneumatic roll feed:mechanical, Bruderer BBV 120/60
pressure:100 tthroat:350 mmstroke:6 - 100 mmno. of strokes:60 /mindistance table/ram, max. stroke up, adjustment up:400 mmtable surface area:850 x 700 mmhole in the table:470 x 150 mmtable height over floor:855 mmram surface:450 x 300 mmram adjustment:80 mmpower requirement:7,5 kWweight:5,0 tdimensions (WxDxH):1,5 x 2,3 x 2,6 mGerman Safety: permitted for manual loading:UVV 11.062 - VBG 7n5.1 clutch:pneumatic overload protection in ram:mechanical
pressure:500 tdistance between columns:2240 mmstroke:1180 mmdistance table/ram, max. stroke up, adjustment up:1800 mmtable surface area:2050 x 1800 mmpressure of drawing cushion in table:250 tstroke of drawing cushion in table:380 mmdrawing cushion surface in table:1800 x 1200 mmpressure of drawing cushion in ram:122 tstroke of drawing cushion in ram:200 mmdrawing cushion area in ram:1800 x 1200 mmram surface:2215 x 1800 mmtable height over floor:500 mmspeed down:400 mm/sspeed up:10 - 400 mm/sworking speed:10 - 100 mm/sdepth of the foundation:3,0 mpower requirement:122 + 75 + 64,5 kWweight:110,0 tDimensions (WxDxH):3,6 x 2,2 x 8,5 mheight over floor:6,8 mGerman Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 drawing cushion in table and ram:hydraulic
pressure: 160 tchamfer lenght: 4100 mmdistance between columns: 3600 mmcolumn arm: 400 mmram stroke speed: 200 mm/secwork speed: 10.0 mm/minreturn speed: 165 mm/secwork stroke: ca. 350 mmdayligth: ca. 660 mmoil volume: 450 ltr.table height: 830 / 950 mmtable width: 75.0 / 60.0 mmvoltage: 400 Volttotal power requirement: 18.5 kWweight: 13440 kgrange L-W-H: 5150 x 2050 x 3150 mm current new price approx. 90.000 euros special price on request------------------------------------------------------ULTIMA PLUS electro-hydraulic press brake with: increased installation height .. approx. 660 mm increased cylinder stroke .. approx. 350 mm------------------------------------------------------ in checked condition - machine video -https://www.youtube.com/watch?v=chgCaXLnpa8Equipment:- CNC electro-hydraulic die/press brake- CYBELEC CNC control DNC 880 S swiveling control panel, front right 2D graphic ...
pressure: 170 tchamfer lenght: 3170 mmdistance between columns: 2700 mmcolumn arm: 420 mmdayligth: 620 mmstroke: 350 mmajustment speed: 160 mm/secworking feed: 10.0 mm/secreturn speed: 100 mm/secoil volume: 280 L0: 300 barcontrolled axis: 7 AnzahlNumber of working hours: ca. 51.500 htotal power requirement: 16.5 KWweight of the machine ca.: 12700 kgrange L-W-H: 4550 x 2650 x 3150 mm LONG STROKE special version Excellent condition () Original price approx. 200.000 Euro Special price on request----------------------------------------------LONG STROKE electro-hydraulic press brake featuring: Increased daylight opening (installation height) = 620 mm Increased cylinder stroke = 350 mm----------------------------------------------Equipment:- Electro-hydraulic CNC press brake- AMADA CNC control AMNC - 7 axes (X1+X2, Y1+Y2, R, Z1+Z2) Swiveling control unit - front left Touchscreen control panel ...
Operating voltage: 380 VFrequency: 50 HzConnection: 1.1 kWSpeed: 2795 rpmPress force: 6 tincl. small hand press and suitable toolReference: Lebendigig - Lot 15 Auction-ID: A7-49882-207
Press force: 35 tTable dimensions: 600 x 500 mmReference: Steinbach & Holler - Lot 334 Auction-ID: A7-49882-130
As good as new machine Operating hours in motion: 29.5 Hour meter: 2244 Strokes: 159328 incl. interchangeable decoiling device, strip straightener and Scrap ejection. Mains voltage: 3LNPE/400V/50Hz Control: Beckhoff/PNOZ multi Electrical wiring diagram: E$-M02070 Pre-fuse: 160 A Nominal power: 37 KW Nominal force: 2000 KN Working capacity: 16000 J Stroke rate in continuous stroke: 30-150 min-1 Max. stroke rate in single stroke: 30 min-1 Max. clutch cycles in single stroke: 20 per min Runtime: 0.158 s Min. safety distance: 317 mm Clutch pressure: 5.0 bar System pressure: 6.0 bar Stroke length: 20-220 mm Max. plunger adjustment: 150 mm Usual stopping point of the ram: OU Table dimensions: 1800x1100 Plunger dimension, max. tool dimension (WxD): 1800x1100 mm Max. weight tool top: 1700 kg Mass without additional equipment: 29000 kg Auction-ID: A1-49750-1
Max. operating pressure 350 bar, 4x additional sideshift connections Auction-ID: A7-49604-22
Current consumption: 4.0 AFrequency: 50/60 HzPower supply: 230 V, 1~ (single-phase) Auction-ID: A7-49604-31
Electric Powered Hydraulic Pump Reservoir 20 liters Hydraulic components from Holmatro Auction-ID: A1-47360-285
pressure: 400 tchamfer lenght: 4050 mmdistance between columns: 3550 mmcontrol: CYBELEC ModEva 10 S total power requirement: 47 kWweight of the machine ca.: 30.400 kgdimensions of the machine ca.: 6000x3000x3450 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Nominal force: 1000 kNHydraulic pressure maximum: 250 barConnected load: 21 kVAMains connection: 400 V, 50 HzDimensions (L × W × H) Length: approx. 2.0 to 3.0 m, width: approx. 1.5 to 2.5 m, height: approx. 3.0 to 4.0 m Auction-ID: A7-49604-17
Max plate thickness: 2.5mm. Max working width: 1020mm. In working order. Auction-ID: A3-46156-6141
General Description High-speed mechanical stamping press manufactured by JELŠINGRAD under licence from Hermann Raster KG, Germany, model BPA-75. Heavy-duty press designed for high-volume progressive-die stamping, punching and blanking from coil. Technical Details Manufacturer: JELŠINGRAD Model: BPA-75 Year: 1985 Serial number: 8510917 Nominal pressing force: 750 kN / 75 t Stroke rate: Infinitely variable 120–600 strokes/min Ram stroke: 10 / 50 mm Ram adjustment: 80 mm Maximum daylight: 400 mm Table: 1,250 × 750 mm Distance between uprights: 730 × 620 mm Maximum strip width: 300 mm Strip feed height: 100–130 mm Feed length per stroke: 5–15 mm Motor power: 15 kW Power supply: 3 × 380 V, 50 Hz Air clutch and brake Compatible with pneumatic strip feeding equipment Electrical cabinet and controls included Condition Used, in good working condition. The machine is currently install ...
Lot of bending tools, incl. metal shelf, different sizes and lengths for more details see photos Auction-ID: A7-49942-1059
Hand Pesse (Schmidt) + Screw Feeder NJR-23 (OHTAKE) and Accessories , Dimensions: 250x80x70 , 130x80x50 , 280x130x140 , for more details see photos of the nameplates Auction-ID: A7-49942-1101
Type: 11V-04-2006 , Dimension: 250x200x550, see photos for more details Auction-ID: A7-49942-1103
Tools press brake belonging to lot 2. Cart edging tools not included Auction-ID: A1-48649-3
pressure: 56.0 tchamfer lenght: 1400 mmdistance between columns: 1300 mmthroat: 220 mmstroke: 200 mmdayligth: 485 mmwork speed: 8.0 - 10.0 m/minreturn speed: 35.0 mm/secControl: CNC Boschert back stop - adjustable: 0 - 370 mmwork height max.: 915 mmCylinders :: 2 Stückvoltage: 3x 400 Vconnected load: 8.0 kVAweight: 3700 kg very good / well-maintained condition () with lots of bending tools- in checked conditions - machine video -https://www.youtube.com/watch?v=NrpZs6Ar0VoEquipment:- NC electro-hydraulic press brake- BOSCHERT NC control unit, front- NC electro-motorized back stop (X axis) with 2x manually adjustable stop fingers (R+Z axis)- AMADA PROMECAM (SYSTEM A) upper tool holder- AMADA PROMECAM (SYSTEM A) lower tool holder- Handwheel with analog display for adjusting the bending angle- lots of insert tools, including tool cabinet- 1x working cylinder = double-acting cylinder- upper ...
Dimensions: 330x250x600, instructions available, see photos for more details Auction-ID: A7-49942-1104
400 € 
