used DEMAG 50

2 x Demag Systec 420 / 820 - 2300 , year of construction / year 2006 , 31,000 h operating hours /running hours. Machines with few operating hours and very good condition / Machines with low runninghours and in good condition. - Screw diameter / Screwdiameter x 80 mm , shot volume / shot volume: 1.583 cm3 Extra Equipment / Extar Equipment : - Enlarged ejector plate lt Euromap / Enlarged ejectionplate according to Euromap. - 2 x air valves on movable clamping plate / 2 x pneumatic valves on movable platen. - 2 x air valves on fixed clamping plate / 2 xPneumatikvalves on fixed platen. - 2 x circuits for hydraulic core pull / 2 x circuits for hydraulic corepull. - 2 x connections for core pull to movable clamping plate / 2 x Connections for corepull on fixed plate.

E-chain hoist, electric hoist, crane DEMAG type DKUN5-500-K-V1F4 Fabr. SKU: 61077868 Year of construction: 1999 Payload 1000 kg Hook travel 6.5 meters Hood lifting speed 10 m/min. Fine lifting speed 1.6 m/min. 2 load trains = 1000 kg mains connection 400 volts, 50 Hz. - Electric chassis DEMAG, type EU/RU 22 DK, 13/6 PF 12/4- Chassis for double T-beams, carrier width 120 to 280 mm - 2 travel speeds 4.6 m/min and 14 m/min - Cable length of the operating bottle 4.5 meters Weight 130 kg good condition; used

Key data: 500 kN

Demag Ergotech Compact 500-200 / Machine in very good technical condition Year of construction: 1997 Injection unit: Screw diameter: 30 mm Spray weight: 94 g Injection pressure: 1990 bar Dosing volume: 106 ccm Clamping unit : Clamping force: 50 t Tie bar spacing: 355x355 mm Size of clamping plates: 520x520 mm Ejector: hydraulic Clamping unit: hydraulic Control: NC4 Additional equipment: Hydraulic core pull x 1 Injection unit hardened - Bimetal Original Demag tool crane: chain, electrically controlled, 2 lifting speeds Metrics: Weight: 3100 kg Length/Width/Height: 3.60x1.40x1.80 m Drive: Pumps/motor: 15 kW Heating capacity: 7.5 kW Total power: 22.5 kW All offered machines are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected machine or to participate in live technical te ...

Key data: 500 kN

Demag Ergotech Compact 500-120 / machine in very good technical condition Year of construction: 1993 Injection unit: Screw diameter: 25 mm Spray weight: 54 g Spray pressure: 2000 bar Dosing volume: 61.3 ccm Clamping unit : Clamping force: 50 t Tie bar spacing: 355x355 mm Size of clamping plates: 520x520 mm Ejector: hydraulic Clamping unit: hydraulic Control: NC4 Additional equipment: Air valve x 1 Hydraulic Core Pull x 2 Injection unit hardened - Bimetal Original Demag tool crane: chain, electrically controlled, 2 lifting speeds Metrics: Weight: 3100 kg Length/Width/Height: 3.60x1.40x1.80 m Drive: Pumps/motor: 15 kW Heating capacity: 5.1 kW Total power: 20.1 kW All offered machines are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected machine or to participate in live  ...

Demag hose pouring machine type: Ergotech 500-200 systems control: NC 4 construction year: In 1999 Schliesseinheit Schliesskraft t: 50 opening ways mm: 400 cross-beam measure mm: 355 installation heights min / max. mm: 210 record size: 520 x 520 hose unity snail diameter mm: 30 hose weights gr: 94 hose volumes cm?: 106 hose pressure cash: In 1995 mass and weights dimensions LxBxH m: 3.6 x 1.4 x 1.8 machine weight kg: 2900 other 1 x nuclear trains

Column-Mounted Crane DEMAG Capacity 500 kg Arm travel 3400 mm Manual arm rotation Column height 3000 mm Column base diameter 700 mm - with base discs (see photo) Electric hoist I beam dimensions: 220 x 100 mm (see photo) Total weight approx 2 T MACHINE IN OUR STOCK IN FRANCE.

Ref. no.: 17518 Producer: DEMAG Year of construction: 1998 Clamping unit Clamping force: 50 ton Opening stroke: 400 mm Distance between tie bars: 320 x 320 mm Mould height min.: 210 mm Mould height max.: 610 mm Platen size (h x v): 540 x 530 mm Injection unit Screw diameter: 22 mm Injection volume: 42 cm³ Shot weight: 37 g Injection pressure: 2591 bar Measurements and weight Dimensions: 3,6 x 1,5 x 1,8 m Machine weight: 3100 kg

Ref. no.: 17706 Producer: DEMAG Year of construction: 2006 Clamping unit Clamping force: 100 ton Opening stroke: 500 mm Distance between tie bars: 400 x 420 mm Mould height min.: 200 mm Mould height max.: 800 mm Platen size (h x v): 600 x 600 mm Injection unit Screw diameter: 35 mm Injection volume: 168 cm³ Shot weight: 149 g Injection pressure: 2400 bar Measurements and weight Dimensions: 5,2 x 1,6 x 2,1 m Machine weight: 5700 kg Robot Producer: Wittmann Type: W602 Year: 2006

Injection moulding machine Demag Ergotech 5000-5200 Parameters: Production year: 2001 Control: NC10 Injection unit: .../5200 Screw diameter: 95 mm Specific injection pressure: 1550 bar Injection volume: 2835 ccm Injection weight: 2550 g Tool closure system: 5000/... Clamping force: 500 t Tool plate dimensions: 1300 x 1200 mm Distance between columns: 900 x 800 mm Tool height: 400...880 mm Opening distance: 810 mm Maximum plate distance: 1690 mm Ejector stroke: 230 mm General data: Dimensions (m) LxWxH: 9,40 x 2,30 x 2,50 m Instrumentation: 6 x pneumatic cascade 2 x Hydraulic Core

Inv. Num. : 6281 Type: 500-200 Producer: DEMAG Produced: 1998 Parameters: Clamping force: 500 kN Equipment: Robot system

Ref. no.: 18197 Hersteller: DEMAG Year of construction: 2005 Clamping unit Clamping force: 150 ton Opening stroke: 450 mm Distance between tie bars: 560 x 460 mm Mould height min.: 230 mm Mould height max.: 460 mm Platen size (h x v): 690 x 660 mm Injection unit Screw diameter: 45 mm Injection volume: 323 cm³ Shot weight: 29ß g Injection pressure: 1973 bar Measurements and weight Dimensions: 4,95 x 1,50 x 2,3 m Machine weight: 7500 kg Robot Producer: Witmann Type: W621 Year: 2004

Offer 22424 Technical data ca : - E. chain hoist make DEMAG DKUN - Operation via corridor remote switch - Load capacity 500 kg - Swivel radius 270 ° - Lifting speeds approx. 1.0 / 4.0 m/min - Hackenweg approx. 3000 mm - Projection approx. 5100 mm - Hook height approx. 2500 mm - lower edge boom approx. 2750 mm - Total height approx. 3550 mm - Column dimensions approx. 320 x 420 mm - Footplate approx. 700 x 700 mm - Drive 400 V - Total weight approx. 600 kg

Key data: 500 kN

Demag Ergotech Viva 500-270 Year of construction: 2003 Injection unit: Screw diameter: 30 mm Injection weight: 95 g Spray pressure: 2573 bar Dosing volume: 106.5 ccm Clamping unit: Clamping force: 50 t Tie bar spacing: 355x355 mm Size of clamping plates: 540x540 mm Ejector: hydraulic Clamping unit: hydraulic Control: NC4 Additional equipment: Euromap 12 Robot Interface Air valve x 2 Hydraulic core pull x 2 pairs Built-in printer for printing reports Metrics: Weight: 2500 kg Length/Width/Height: 3.65x1.15x1.95 m Drive: Pumps/motor: 18.5 kW Heating capacity: 7.5 kW Total power: 26 kW All offered machines are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected machine or to participate in live technical tests at our company in Łódź. Price: On request

SUMITOMO-DEMAG IntElect 210/580 Clamping force : 210 Tons Screw diameter : 35.0 mm Tie bar spacing (H) : 580.0 mm Tie bar spacing (V) : 580.0 mm Shot volume : 178.0 cm³ Shot weight : 158.0 g Pressure on material : 2800 bar Platen length : 880.0 mm Platen width : 850.0 mm Opening of the press : 1265.0 mm Mould size : 690 Length x width x height : 6260.0 mm × 1555.0 mm × 2071.0 mm Weight : 9800.0 kg Worked hours : 26615 hours Hours under power : 32244 hours State excellent At local norms : yes Status : under power max inj stroke -185 mm Operating hours – CPU-32143 ,Drives -26215 ,Heating -26500 Total cycle -16686388 Clamping Force 2100 KN Injection unit 500 Screw diameter 35 mm 400 V / 50 HZ Manufacture year –October 2010 Net Weight-9800 kg Injection and Clamp Drives renewed in 2015 The machine is in excellent cond ...

Molding machine of Mag Type: Ergotech, 150/500-840 concept control: NC 4 year of construction: 2001 Clamping unit Clamping force t Gap 150 mm: 500 Holm dimension mm: 500 x 500 min/max height mm: 275 / 585 Plate size: 1085 x 1185 injection unit Screw diameter mm: 50 Injection weight gr: 402 Injection volume cm m³: 442 Spray pressure bar: 1946 Dimensions and weights Dimensions Lxwxh m: 5.2 x 1.6 x 2.1 machine weight kg: 7,800

Fully functional machine in good condition. Screw diameter 45,0 mm Tie bar spacing (H) 500,0 mm Tie bar spacing (V) 500,0 mm Shot weight 291,0 g Pressure on material 1910,0 bar

arm length: 4500 mm total column height: 4200 mm weight max. in kg: 500 kg bottom edge arm: 3200 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

arm length: 4000 mm weight max. in kg: 500 kg swivelling range: 180 Grad total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m with wall bracket The techn. Data are manufacturer or operator information and are therefore not binding for us. We reserve the right to prior sale, only our terms and conditions apply. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

arm length: 4000 mm weight max. in kg: 500 kg swivelling range: . Grad total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m 44 with wall bracket The techn. Data are manufacturer or operator information and are therefore not binding for us. We reserve the right to prior sale, only our terms and conditions apply. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

arm length: 4000 mm total column height: 4200 mm weight max. in kg: 500 kg bottom edge arm: 3200 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

16 meter vertical lift capacity! Kind of: overhead travelling crane Capacity: 10 ton Span: 5000 mm Drop: 16 meter!!! Numbre of riggers : double girder

Key data: 5000 , 2550 , 95

Year of construction: 2001 Clamping force: 5,000 KN with 6-axis Fanuc robot M16i , Year of construction 2001 incl. conveyor belt and safety fence Equipment: Screw: diameter 95 mm Injection weight: 2,550 gr./hp Ejector stroke: 230 mm Tie bar spacing: 900 x 800 mm Installation height min. – max.: 400 – 880 mm Max. distance between plates: 1,690 mm Opening travel max.: 810 mm Max. tool weight: 6,700 KG 6-fold cascade pneumatic 2 core pulls Robot interface Injection pressure max. 1,550 bar Control NC10

Year of construction: 2001 Clamping force: 5,000 KN with 6-axis Fanuc robot M16i , Year of construction 2001 incl. conveyor belt and safety fence Equipment: Screw: diameter 95 mm Injection weight: 2,550 gr./hp Ejector stroke: 230 mm Tie bar spacing: 900 x 800 mm Installation height min. – max.: 400 – 880 mm Max. distance between plates: 1,690 mm Opening travel max.: 810 mm Max. tool weight: 6,700 KG 6-fold cascade pneumatic 2 core pulls Robot interface Injection pressure max. 1,550 bar Control NC10

Hydraulic pressure: 210bar, weight: 3.1t.

Screw diameter: 95mm, distance between the bars: 900x800mm, max. opening path: 810mm, max. tool weight: 6.7t, operational pressure: 190bar, weight: 24t, with Industrial Robot FANUC M-16iL.