We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
Working width 1000 mm Still in operation: Yes Available: immediately
used
roller cutter, overhauled, working width: 110 cm, roller diameter, 100 cm, pneumatic winding shafts 70/76/150 mm, hydraulic lifting/lifting device, side edge control, dancer roller, load control with control brake, surface needle, Siemes S5 Still in operation: Yes Available: immediately
working width 1000 mm Still in operation: Yes Available: sofort
used
Slitter rewinder, reconditioned, working width, 110 cm, winding diameter: 100 cm, pneumatic winding shafts 70/76/150 mm, hydraulic lifing in and out mechanism, Web guide unit, tension control unit with adjustable brake, overall perforation, Siemens S5 Still in operation: Yes Available: sofort
Qty. 1 Second-hand aluminium foil rolling mill plant Mfc.: Robertson, Kampf, Schmutz, Nishimura, Waldrich-Siegen, Otto-Junker Built: 1962 – 1989 Foil width: 850 mm Entry thickness: 0.4 mm Exit: 2 x 7 microns Scope of supply: Roughing Foil rolling mill: 4-Hi Intermediate foil mill 4-Hi Finishing foil mill 4-Hi Slitters – Qty. 4 Roll grinders – Qty. 2 Annealing furnaces – Qty. 4 Charging car INDIVIDUAL ITEMS CAN BE SOLD!!
Qty. 1 Second-hand slitting line Mfc.: Kampf Built: 2001 Re-Installed in 2016 under power – no production! Material Processed: Al. Alloys 1145, 1100, 3003, 7072 and 8111 Temper: 0 Thru H19 Strip Width: 635 - 1753 mm (25" - 69") Thickness: 0.05 - 0.381 mm (0.002" - 0.015") Slitting Width: 15.8 mm - 1169 mm (0.6" - 46") Max. 40 Cuts Plus Edge Trim According to Kampf, this Line will run Can Lid Stock: 0.93 mm (0.037") and "O Temper" Dead Soft Aluminum at 2.06 mm (0.081") with Knife Modifications. Line Speed Max: 800 m/min. (2600 Ft/min.) depending on material type, thickness, etc.
used
Slitter rewinder for foil, paper, foiling and laminates. 7 my -200 my Max. material width = 1250 mm Speed max. mech = 350 m/min, Rewinder max. = 600 mm Min. working width = 25 mm, sleeve 76 mm, Max. working width = 1250 mm, sleeve 76 mm,, Unwinder (shaftless) diameter max. = 1000 mm Sleeve = 70-76/ 150 -152 mm, Cutting system = paper cutting, Side edge control , 16 knives included,
used
2 Coilhaken 1 x 9 t 1 x 1 t
used
Unwinding reel / decoiler â?¢ Bandwidth / strip width max. 1,500 mm â?¢ Tape thickness / strip thickness (430 N/mm2) 0.5-2.0 mm â?¢ Coil outer diameter / coil outer - 1,300 mm â?¢ Coil inner diameter / coil inside - 470-520 mm â?¢ Coil weight / coil weight 10,000 kg â?¢ Side shift / side shift . . . . . . . . . . . . . . . . .
new
Cut-to length slitting machine SM-1250х8 Cut-to-length slitting machine is used for longitudinal cutting of the metal sheets with maximum thickness 1mm, aluminum composite panels, paper, polycarbonate thanks to special cutting knives that are fixed on rolls of the slitting machine. This cut-to-length slitting machine lets you to cut the material into eight strips. The diameter of the rolls is 56 mm There are four types of the sheet metal cut-to-length machines we make: The manual cut-to-length slitting machine (cutting for 2 strips) The electric cut-to-length slitting machine (cutting for 3-4 strips) The electric cut-to-length slitting machine (cutting for 6-10 strips) The electric cut-to-length slitting machine (cutting for 12-20 strips) The operator of cut-to-length slitting machine can easily change the width of the strips and their numbers. There are special scr ...
used
60″ x .135″ x 20,000Lb Cincinnati – Forte Loop Slitting Line Material Width: 12″ – 60″ , Thickness: .010″ – .135″, Weight: 20,000Lb, Coil ID: 16″ – 24″, Coil OD: 72″, Speed: 600 fpm, Direction: Left to Right. Entry Turnstile, Entry L-Type Coil Car, Mandrel Uncoiler with Hold-Down Roll, Powered Peeler, Driven Pinch Rolls, PVC Applicator, Entry Shear, Two Slitting Heads, Injection Design, 5″ & 7″ Arbor Diameter, 75HP DC Motor, Two (2) Hydraulic Scrap Winders, Pit Cross Over Table, Drag Board & Rotary Tension Stand, Recoiler with Over-Arm Separator & Push-Off, 150HP DC Motor, Exit L-Type Coil Car & Turnstile. Electrics, Hydraulics, Controls, Tooling, Spare Parts
used
12″ x .125″ x 4000Lb Bliss Slitting Line Make: Bliss Material Width: .075” – 12” Material Thickness: .008” – .125” Weight Capacity: 4,000Lb Coil ID: 16” – 20” Coil OD: 72”
used
18″ x .070″ x 6,000Lb Morvay Slitting Line Material Width: 18″, Weight Capacity: 6,000Lb, Material Thickness: .008″-.070″, Coil ID: 20″, Direction: Left to Right. Mandrel Uncoiler with Disc Brake, Powered Mandrel Expansion, Powered Hold-Down Roll, Driven Entry Pinch Rolls, Slitting Head with Adjustable Arbors, Knives & Tooling, Recoiler with Hydraulic Push-Off, Powered Over-Arm Separator, 50HP Motor, Exit 2-Arm Turnstile
used
60″ x .135″ x 40,000Lbs Yoder Slitting Line Material Width: 12″ – 60″ Material Thickness: .010″ – .135″ Weight Capacity: 40,000Lbs Coil ID: 20″-24″ Coil OD: 72″ Pull Through Design Entry Coil Car Mandrel Uncoiler with Hold-Down Roll Hydraulic Peeler Driven Pinch Rolls Slitting Head with Gear Box and AC Feed-Up Motor Single Scrap Winder Recoiler with Over-Arm Separator DC Motor Drive Exit Turnstile Electrics, Hydraulics, Controls
used
72″ x .187″ x 50000Lb Paxson Loop Slitting Line Make: Paxson Material Width: 12″ – 72″ (Uncoiler 60″) Material Width: .010″ – .187″ Coil Weight: 50,000Lb Coil ID: 20″ – 24″ Coil OD: 72″ Speed: 500 /1000 fpm Direction: Right to Left Material Strength: 40,000 yield / 50,000 psi shear Material: CR, HR, Galvanized Entry Transfer Cart Entry Coil Car Mandrel Uncoiler Powered Hold-Down Roll Powered Expansion Sliding Base Hydraulic Peeling Table Driven Pinch Rolls
used
Universal Slitting Line 72″ x .187″ x 20,000Lb Material Width: 12″ – 72″ Material Thickness: .015″ – .187″ Coil Weight: 20,000Lb Coil ID: 20″ Coil OD: 72″ Direction: Left to Right Entry Floor Standing Coil Car L-Type Design Hydraulic Lift & Traverse Mandrel Uncoiler Powered Hold-Down Roll Hydraulic Expansion Air Cooling Brake Sliding Base Hydraulic Peeling Table Slitting Head Arbor Diameter: 7″ Powered Arbor Adjustment 100HP DC Motor Knives & Tooling Recoiler Powered Push-Off Hydraulic Over-Arm Separator Hydraulic Expansion 100HP DC Motor Exit 2-Arm Turnstile Arm Width: 72″ Powered Rotation Complete Slitter with Electrics, Hydraulics, Controls, Tooling
used
Paxson Loop Slitting Line 72″ x 0.375″ x 50,000Lb (A3754) Make: Paxson Material Width: 12″ – 72″ Weight Capacity: 50,000Lb Thickness: .050″ – .375″ Coil ID: 20″ – 30″ Coil OD: 72″ Line Speed: 850 feet per minute Direction: Right to Left Entry L-Type Coil Car Floor Standing Design Hydraulic Lift & Traverse Self Contained Hydraulics Mandrel Uncoiler Powered Hold-Down Roll Hydraulic Expansion Water Cooled Brake Feed-Up Motor Sliding Base Hydraulic Peeling Table Driven Pinch Rolls Adjustable Edge Guides 4-Roll Coil Breaker Mechanical Entry Crop Shear Two (2) Slitting Heads Arbor Diameter: 9″ and 12″ Crane Removable Type Adjustable Arbors 150HP DC Motor Drive Multi Speed Gear Lots of Knives and Tooling Two Pro-Eco Scrap Winders Max Thickness: .500″ 25HP Motor for Each Unit Powered Open / Close Pit Cross Over Table Drag Bo ...
used
Bandwidth.............................. 870 mm Band thickness................ 0.2-3.0 mm Coil weight................ 10 to. Coil ID Unwinder................... 400/508/750 mm Coil ADBewinder.................. 1,500 mm Cutting performance................. 110 N/mm2 Velocity.................... 120 m/min.
used
Cut-to-length line Auxmet strip line Unwinding reel for max 4to coil weight Bandwidth 50-1000mm Material thickness 0.5-3mm at 600N/mm2 Line speed 60m/min Number of stripes 1-11 Reel reel up to 4to coil weight with foiling unit without knife with retrofitted photoelectric sensors The offer is aimed exclusively at traders within the meaning of §14 BGB
used
Stock number: 3778 CUTTING LINE Manufacturer: MORGAN , Type: 1330 x 0.7 - 3.2 mm Specifications: Size scissors length 1330 mm Size sheet thickness 0.7 - 3.2 mm - Roller feed 2 pc dia. 100 rools Composed of: - Straightening machine 5 pc. dia 100 Reels - Drain reel 5 ton dia. 530-610 mm tone - Scissors Morgan 1500 x 3.2 mm Accessories: Coil trolley 5 ton Length: 6500 mm, Height: , Width: 33.00 mm, Weight:
used
Slitting line Pro-Eco 72″ x .250″ x 74,000Lb (A3774) Slitting line Pro-Eco 72″ x .250″ x 74,000Lb (A3774) is perfect solution for longitudinal cutting of coil metal into strips. This line can work with very big coils up to 74,000 Lb weight and 0.25 inches maximum metal thickness. Line is strong enough to make cutting speed 200 – 600 fpm depends on metal thickness and width you work with Slitting line Pro-Eco 72″ x .250″ x 74,000Lb (A3774) Manufacturer: PRO ECO Material: CRS, HRS, HPP & O Material Width: 12″ – 72″ Material Thickness: .060″ – .250″ Coil Weight: 74,000Lb Coil ID: 20″ – 30″ / 20″ – 24″ Coil OD: 72″ Line Speed: 200 – 600 fpm Direction: L-R Three (3) Coil Storage Ramp Coil Car Powered Lift & Traverse Double Cone Uncoiler Sliding Base Dual Water Cooled Brake Feed-Up Motor Powered ...
used
CINCINNATI ACW6 slitting line is used in the processing of thin steel sheets with a maximum thickness of 4 mm. The process consists in gradually unrolling the sheet coils towards cutting rollers with special roller knives with a thickness of 5 to 30 mm, and then passing the sheet between the rollers for precise slitting. After the slitting process, the sheet is wound onto coils ready for further processing. The ACW6 slitting line guarantees the highest product quality while making optimum use of the raw material. The CINCINNATI coil slitting line consists of: – sheet decoiler – sheet metal winder – roller knives (thickness 5 mm, 10 mm, 12 mm, 20 mm, 25 mm, 30 mm) – ejector spacers (width 10 mm, 12 mm, 20 mm, 25 mm, 30 mm) – slitting aggregate unit – brake Technical specifications of the CINCINNATI ACW6 slitting line - maximum sheet thickness: 4 mm - minimum shee ...
used
Bandwidth................. 500 mm Strip thickness.................. 0.3-2.5mm Coil weight................. 5,000 kg Velocity......... 70 - 120 m/min. Coil I Diameter...... 508 mm Coil A diameter..... 1,500 mm
used
Slitting line Fimi 1500×2.5mm x15t (A3783) Manufacture FIMI ITALY Year 1990 Strip width Min. 200 mm Max. 1500 mm Strip thickness 0.3 – 2.5 mm Coil weight Max. 15 t Coil- Max. 1500 mm Speed Max. 80 m/min Working direction Right Left The line consists of: Decoiler Mandrel Cone-Ø 480 – 610 mm Drive / braking Hydraulic motor Lifting table Hydraulic Coil opener / pinch roll unit Telescopic table Hydraulic No. of pinch rolls 2 Pinch roll-Ø 400 mm Driving motor 25 kw Slitting head No. of heads 2 Shafts diameter 120 mm Main drive D.C. motor Driving power 92 kW Scrap baller Minimum scrap width 5 mm Maximum number of slits 17 Slits up to 1.0 mm 5 Slits at 2.5 mm Brakes Pneumatic Press up and dow Re coiler Capacity 15 t Diameter 508 mm Driving power 120 kw Term style 4 arms x 15 ton