used DIEFFENBACHER Hydraulic Open Gap Presses

Capazitat 300 Tone Table size 1,500 x 1,500 mm Stosselv creation 500 - 1,000 mm Piston x 400 mm Delete. Table - Stossel Minimum: 500 mm Maximum: 1,500 mm Machine height 4,000 mm Bottom of the floor 1,000 mm Top of the floor 3,000 mm Machine Weight 18.600 kg

Pressing force: 3200kN, stroke: 700mm, table dimensions: 2500x1300mm, weight: 63t, with documentation.

pressure: 320 t throat: 800 mm stroke: 630 mm distance between table / ram: max. 1000 mm ram head dimension: 710 x 600 mm table-size: 800 x 1200 mm work height max.: 1015 mm quantity of oil: 1100 l Number of working hours: 7663 h weight of the machine ca.: 15 t dimensions: ca. 1600 x 2200 x 4800 mm dimensions of switch cabinet: ca. 1200 x 400 x 1800 mm Tested for function. During the test run it is noticed that the press ram not 100% leak-proof. In addition, the cable for manual operation was mended several times. Upper cover is missing, since this was dismantled by the customer due to crane use. Operating instructions and electrical plans available. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 2000 /1000* t distance between columns: 2650 mm stroke: 500 mm column travel -side: 500 x 1000 mm diameter of piston: 710 mm number of pistons: 2 distance between table / ram: 1000 mm operating pressure: 130 / 230 bar dayligth: 800 mm table length: 2500 mm table width: 1600 mm table height: 250 mm draw back pressure: 500 kN number of T-slots: 8 turning speeds: 1500 U/min rapid speed: 120 - 140 mm/min closing speed: max. 120 - 140 mm/sec. hydraulical ram locking: return of plunger by small single cylinders: 100 - 110 mm/sec cutting sound absorber: 300 t die cushion capacity: 200 t die cushion stroke: 250 mm speed of die cushion: 100 mm/sec voltage: 380 V frequency: 50 Hz quantity of oil: 2000 l total power requirement: 93 kW weight of the machine ca.: 90 t dimensions of the machine ca.: 5000 x 2500 x 7200 mm transport measurements: ca. 6500 x 3750 x 2190 mm 1991 assembly of a d ...

pressure:1000 t distance between columns:3030 mm stroke:350 mm Distance table/ram, max. stroke up, adjustment up:1400 mm table surface area:3000 x 2000 mm table height over floor:430 mm side window:1450 x 1400 mm ram surface:3000 x 2000 mm speed down:300 mm/s speed up:340 mm/s working speed:18 - 44 mm/s return capacity:120 t oil volume:4400 l width with platform:4950 mm power capacity:2 x 90,0 + 10,0 kW weight:87,0 t Dimensions (WxDxH):4,35 x 3,65 x 7,55 m height over floor:6,05 m height beneath floor:1,5 m German Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2

pressure:500 t distance between columns:1910 mm stroke:500 mm Distance table/ram, max. stroke up, adjustment up:700 mm table surfache without cutting impact cushions:1910 x 1360 mm table surfache with cutting impact cushions:1600 x 1360 mm table height over floor:800 mm ram surface:1600 x 1270 mm Side window:600 mm speed down:400 mm/s speed up:330 mm/s working speed:10 - 28 mm/s oil volume:1200 l power requirement:60,0 kW weight:40,0 t Dimensions (WxDxH):3,6 x 2,5 x 5,0 m height over floor:4,5 m German Safety: permitted for manual loading:UVV 11.062 - VBG 7n5.1 cutting impact cushioning:hydraulic ram interlocking:hydraulic

Technical data: -maximum pressing force 40 t -maximum piston stroke 500 mm -Hoisting speed 0-40 mm / s -Return 0-200 m / min -Mounting height 750 mm -Projection up to mid slide 360 mm -Slide clamping surface 440 x 360 mm -Slide clamping pins 40 mm -Table size 630 x 500 mm -Table hole / breakthrough 200 mm -Table height above floor 710 mm -Oil quantity approx. 300 ltr -Drive 400 V / 4 kW -Space requirement approx. B H 1200 x 2800 X 1600 mm -Weight approx. 2500 kg

a hydraulic single-stand drawing press Müller model CLZ.100.1.34, Y.O.M. 1994, good condition, with UVV, Siemens S7 screen control, throat gap 400 mm, installation height 800 mm, table surface 800 x 730 mm, stroke 600 mm, drawing cushion 40 to., drawing cushion stroke 200 mm.

No. 4877: 1 gebr. Single-stand hydraulic press Fabr. EITEL, Type T 6.3, Bauj. 1973

Pressing force: 8 t Table surface: 450x260 mm Stroke: 250 mm Projection: 175 mm Lifting speed: 3.9 m/min Retraction force: 4,000 kg Engine: 4 hp Weight approx. 1 t

Pressing force 1000 kN Table size 750 x 560 mm, diarrhoea opening 100 mm Installation height 800 mm, stroke 500 mm Projection 360 mm Bear size 530x400 mm, 2 T-slots Ram speed: down 200 mm/sec, up 400 mm/sec Connection load approx. 21 kW Incl. Feeder WE16 for 160 mm bandwidth Coil tray and straightening unit Fabr. OFFICE; Type CA200/R40-7, YOC 1994 Reel, loop control Two-hand operation Manuals

YOM: 5.1987 / 2003 - the press was generally renovated by the manufacturer Schuler, along with the replacement of electrics, cables and controls for Siemens Condition: Very good Technical details: Pressing force: 5000 kN, 500 tone Table dimensions: 1500 x 1400 mm Distance from Clamping surface to ram: 1250 mm Distance from the clamping table to the hold-down device min.405 mm, max.605 mm Clamping surface thickness: 335 mm Number of flutes, dimensions: H12 DIN 650, 36 mm Ram size Stroke:: 500 mm Hold-down size Stroke: 200 mm Press height / weight: 5800 mm / 45 tone

Two-hand and foot operation Pressing force: 1000 kN Projection: 380 mm Stroke: 650 mm Distance table/plunger, gr. stroke top, verst. above: 950 mm Ejector with end position damping on both sides Ejector travel: 150 mm Ejector force: 160 kN Pressure piece hardened: Ø 98 mm Table surface: 720 x 630 mm Total weight: 7,400 kg

Hydraulic precision press Make: JOSSI (CH) Type: HP-5-N Pressing force: max. 5 to (50 kN) Operating pressure: max. 200 bar Installation height: max. approx. 120 mm. Projection: approx. 105 mm. Piston stroke: max. approx. 90 mm. Mounting hole in the piston: 14 mm. Table mount, height adjustable. Incl. 2 hand controls and/or foot release with switch and rollable base. Unfortunately, the table top is missing. Weight: approx. 350 kg, dimensions WxDxH: approx. 85 x 55 x 190 cm. Good used and ready for use. The machine can be viewed and demonstrated under power.

Inv. číslo: 4465 Type: PL-140 LC Výrobce: OMC Vyrobeno: 2014 Parametry: Příkon: 75 kW

Offer 23321 Technical data approx.: - Max. pressure capacity 10 T - Operating pressure min. – max. 15 - 180 bar - Projection 180 mm - Max. installation height 340 mm - Stroke 70 mm - Tool holder 25 mm - Table dimensions W 350 x D 280 mm - Table bore / passage 90 mm - E.- Footswitch - Drive 400 V / 3 kW - Space requirement approx. W 450 x H 1000 x D 800 mm - Space requirement base frame approx. W 450 x H 820 x D 800 mm - Weight approx. 500 kg

Inv. Num. : 4464 Type: PL-F UP Producer: OMC Created: 2014 Parameters: Compressive force: 105 t Under table length: 3500 mm Under-table width: 1300 mm Total power requirement: 3 kW Machine height: 1940 mm Machine length: 4000 mm Machine width: 1600 mm Machine weight: 4 t

Specifications: Press force adjustable 10 – 100 kN Projection 210 mm Table size W x D approx. 500 x 400 mm Installation height with/without clamping plate 300 mm Stroke 100 mm

Key data: 10 t, 300 mm, 510 mm

Table 470x460 , installation height 605

Key data: 10 t, 300 mm, 300 mm

more info on request

Stroke: 300, table 450x370, 1300kg

Key data: 1 t, 110 mm

Hydraulic fine press, MATRA, , up to 1000kg, table: 260x200mm, projection 110, Foot or manual release, without UVV Fully functional, energized to visit

Force of pressure: 75 t projection: 300 mm table size: 620 x 800 mm Durchfalloch in the table: 225 x 325 mm table adjustment: 175 mm plunger surface: 180 x 475 mm slide adjustment: 80 mm stroke adjustment: 16-140 mm stroke rate: 90 / min drive motor: 380 V, 3 kW space: 1700 x 1200 x 2500 mm weight: 3300 kg

Force of pressure: 40 t projection: 250 mm table size: 440 x 530 mm Durchfalloch in the table: 170 Ø mm table adjustment: 220 mm plunger surface: 200 x 280 mm slide adjustment: 60 mm stroke adjustment: 8-80 mm stroke rate: 100 / min drive motor: 380 V, 2.5 kW space: 950 x 1450 x 2050 mm weight: 2400 kg

Force of pressure: 100 t projection: 350 mm table size: 690 x 840 mm Durchfalloch in the table: 160 mm table adjustment: slide area: 450 x 600 mm slide adjustment: 80 mm stroke adjustment: 8-100 mm stroke rate: 60 / min drive motor: 380 V, 5.5 kW space: 1850 x 1850 x 2650 mm weight: 6800 kg