used ADAM RICHTER Open Gap Eccentric Presses

Pressing force: 350t, stroke: 30-200mm, stroke adjustment: 130mm, stroke speed: 30/min, table dimensions: 1700x1250mm, including Roller Feeder Straightening Machine ALBA VhyRia 600S and uncoiler.

Stroke adjustment: 29-160mm, ram adjustment: 130mm, stroke speed: 48/min, connected load: 14kW.

Exhaust silencer type KRNS 45 DN 250 according to the reflection and absorption principle in vertical design Outer diameter: 600 mm x height 14000 mm Nominal entry distance DN 250 (Ø 273.0 mm), radial in height of 2500 mm (?) with flange and counter flange, Flange hole circuit according to EN 1092-1/02/PN10 Material flanges St 37 galvanized Flanging made of V4A, screws and seal Nominal outlet diameter DN 250 (Ø 273.0 mm), axially with pipe end made of stainless steel sheet V4A (W.Nr. 1.4571) static calculation basis DIN 4133, Wind load zone 3

Manufacturer: Adam Bodenabsetzer, Type: Aufrichter, Year: ca.1998, Control: keine, Corpus length max mm: 1200, Working hight mm: 950, Hydraulical: Motorisch, Belt width: 600/1300, Total power kW: ca.5, Year :ca.1998

Spindle press make RICHTER type HSP 25Machine -No: 510 built in 1953Max. Press force: 25 tTable size: 540 x 400 mmBear size: 420 x 200 mmSpindle diameter: 70 mmStroke: 180 mmExternal dimensions approx: 1200 x 1200 x 2000 mmused, despite the year of construction in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

pressure: 160 t dayligth: 600 mm stroke: 25 - 150 mm table surface area: 1500 x 900 mm ram surface: 1500 x 900 mm ram adjustment: 100 mm daylight between the columns: 1500 mm daylight between the side columns: 400 x 200 mm distance between columns: 1680 mm weight of the machine ca.: 15 t dimensions of the machine ca.: 2,7 x 1,8 x 4,4 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Single Stand - Eccentric Press PELS - RICHTER Type PEKR 125 Masch. No. 20684 Year of construction 1967 Compressive force 125 ton. Projection 430 mm Table size 1100 x 750 mm Ram surface 890 x 650 mm Table opening 400 mm Stroke adjustment 6 to 115 mm Ram adjustment 100 mm Installation height largest stroke above max. 450 mm Clamping pin bore 50 mm Stroke rate 60 strokes/min. Table height above corridor 900 mm Motor power 7.5 kW Mains connection 380 volts, 50 Hz - Overload protection by crushing plate in the plunger - Compressed air Clutch-brake combination DESCH- Plunge weight compensation cylinder - Manual ram position - Two-hand operation - Cam switchgear - Grease central lubrication Vögele - Stroke counter Space requirement L x W x H 2300 x 1450 x 3030 mm Weight approx. 10 ton. good condition; used

Single Stand - Eccentric Press PELS - RICHTER Type PEKR 125 Masch. No. 20684 Year of construction 1967 Compressive force 125 ton. Projection 430 mm Table size 1100 x 750 mm Ram surface 890 x 650 mm Table opening 400 mm Stroke adjustment 6 to 115 mm Ram adjustment 100 mm Installation height largest stroke above max. 450 mm Clamping pin bore 50 mm Stroke rate 60 strokes/min. Table height above corridor 900 mm Motor power 7.5 kW Mains connection 380 volts, 50 Hz - Overload protection by crushing plate in the plunger - Compressed air Clutch-brake combination DESCH- Plunge weight compensation cylinder - Manual ram position - Two-hand operation - Cam switchgear - Grease central lubrication Vögele - Stroke counter Space requirement L x W x H 2300 x 1450 x 3030 mm Weight approx. 10 ton. good condition; used

pressure: 65 t throat: 370 mm stroke: 29-151 mm no. of strokes: 50 Hub/min ram - range of adjustment: 80 mm table surface area: 1300x700 mm ram surface: 1000x600 mm hole in the table: ¦ 110 mm table height: 800 mm tool hole in ram: Ø 40 mm weight of the machine ca.: 6 t dimensions of the machine ca.: BxTxH 1700x2000x2800 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Pressure gauge, test pressure gauge, pressure gauge with Bourdon tube, pressure and temperature measurement technology, contact pressure gauge -Manufacturer: Richter, manometer pressure gauge with limit signal transmitter -Type: 0 to 6 bar -Limit signaller: Type M1 -Screw connection: see photos -Dimension: 170/135/H135 mm -Weight: 2.1 kg

pressure:160 t distance between columns:2050/1900 mm stroke:15 - 170 mm no. of strokes:15 - 40 /min distance table/ram, max. stroke up, adjustment up:690 mm table surface area:1600 x 800 mm side window:800 mm ram surface:1620 x 700 mm ram adjustment:140 mm power requirement:15,0 kW weight:24,0 t Dimensions (WxDxH):3,3 x 2,3 x 5,3 m height over floor:4,8 m height beneath floor:0,5 m clutch:pneumatic ram adjustment:motoric ram counterbalance:pneumatic

Force of pressure: 75 t projection: 300 mm table size: 620 x 800 mm Durchfalloch in the table: 225 x 325 mm table adjustment: 175 mm plunger surface: 180 x 475 mm slide adjustment: 80 mm stroke adjustment: 16-140 mm stroke rate: 90 / min drive motor: 380 V, 3 kW space: 1700 x 1200 x 2500 mm weight: 3300 kg

Force of pressure: 40 t projection: 250 mm table size: 440 x 530 mm Durchfalloch in the table: 170 Ø mm table adjustment: 220 mm plunger surface: 200 x 280 mm slide adjustment: 60 mm stroke adjustment: 8-80 mm stroke rate: 100 / min drive motor: 380 V, 2.5 kW space: 950 x 1450 x 2050 mm weight: 2400 kg

Force of pressure: 100 t projection: 350 mm table size: 690 x 840 mm Durchfalloch in the table: 160 mm table adjustment: slide area: 450 x 600 mm slide adjustment: 80 mm stroke adjustment: 8-100 mm stroke rate: 60 / min drive motor: 380 V, 5.5 kW space: 1850 x 1850 x 2650 mm weight: 6800 kg

Pressure: 65 tons -Stroke: 140 mm -Table size: 720 x 600 mm -Plunger surface: 500 x 300 mm -Tappet adjustment: 80 mm -Strokes: 20-40 per min. -. Weight: 6000 kg -Dimensions (L x W x H): height 3.1 m -Clamping hole ø 60 x 80 mm More info on request

very fast Eccentric press, make SCHULER , tested , electrically connected Type PDv 25/200 Masch.-No. 70/32.0610/9 Technical data: Power 25 to Number of strokes approx. 180 /min Extension 200 mm Impact stroke 8 - 80 mm Shock sift creation approx. 60 mm Table size approx. 570 x 410 mm Installation height approx. 310 mm (measured with mounted clamping plate) Width x Depth approx. 1.1 x 1.35 m plus control cabinet Height approx. 2.15 m Engine power 3 kW Weight estimated approx. 1.5 to

Nominal force 400 kN Stroke rate - 70/140 / min Motor 3/4 kW Exploitable stroke - at constant. Clutch brake temperature 50/45/min Capacity - material thickness 4-6.4 m - with single strokes, 2-3.2 mm - with continuous stroke Table 660 x 530 mm, table top 650 x 515 x 75 mm Stroke adjustment - 10-125 mm, Dimensions 1250 x 1600 x 2370 mm - High , Btto 4500 kg Reconditioned machine - warranty 9 months from delivery date

Raskin Master 50 ton Capacity: 50 ton Deph of throat: 240 mm Max adjustable stroke: 10 > 80 mm Distance between table -- ram: 360 mm Table area: 650 x 500 mm Electric motor (power): 5,5 HP Weight: 2350 kg

Plunger pressure 4 t Stroke rate 70 / min

Compressive force: 25 t Projection: 200 mm Table size: 450 x 600 mm Table adjustment: 240 mm Plunger adjustment: 70 mm Stroke adjustment: 4 - 80 mm Stroke rate: 150 rpm Drive motor: 380 V, 1.1 kW Space required: 1600 x 850 x 2000 mm Weight: approx. 1450 kg

Compressive force: 25 t Projection: 200 mm Table size: 450 x 600 mm Hole in the table: 100 x 210 mm Table adjustment: 240 mm Plunger adjustment: 70 mm Stroke adjustment: 4 - 80 mm Stroke rate: 150 rpm Drive motor: 380 V, 1.1 kW Space requirements: 1300 x 800 x 2000 mm Weight: approx. 1450 kg

Thomas 10 ton Capacity: 10 ton Deph of throat: 250 mm Table area: 285 x 240 mm

Key data: 75 t

Specifications: Capacity 75 tons Stroke rate 90 strokes Projection 300 mm Plunger stroke 16 - 140 mm Plunger adjustment 80 mm Table size approx. 800 x 600 mm Installation height max. approx. 400 mm

Bret PCK 160 ton Capacity: 160 ton Deph of throat: 405 mm Max adjustable stroke: 20 > 200 mm Workingspeed: 40 > 80 strokes/min Passage between uprights: 960 mm Max ram adjustment: 150 mm Electric motor (power): 22 kW Length : 2050 mm Depth : 2235 mm Hight: 4200 mm Weight: 18 ton

Specifications: Capacity 50 tons Stroke rates 115 rpm Projection 250 mm Plunger stroke 8 - 120 mm Plunger adjustment approx. 70 mm Table , WxD approx. 650 x 500 mm Diarrhoea och approx. 250 x 180 mm