Kenar yapıştırma makineleri

Description: Min Panel Width 80 mm Max Panel Thickness 60 mm Thickness Min 10 mm Panel Feeding Speed ​​9-14 m / min 380 V 50 Hz Motor Power 8 Kw Noise 84.8 DbApprox. Onsite Dimension. (l x w x h): 1,400 x 1,100 x 1,200 mm, weight approx.: 800 kg

Description: • Edgebander • Serial number 2697 • Edge thickness in roll from 0.40 mm up to 3 mm • Worpiece thickness from 8 mm up to 40 mm • Feed motor 0.37 KW • Edge feeder, edge magazine for one edge coil • Gluing unit with pot for granulated hot melt adhesive • Pressure group with (1+2) rollers • End trimming unit • Fine trimming unit, 2 x motor 0.36 KW-12000 rpm, tiltingApprox. Onsite Dimension. (l x w x h): 2,800 x 980 x 1,450 mm, weight approx.: 700 kg

Description: -Edge height: 13 - 50 mm -Max. solid wood cross-section: 15x45 mm -Min panel length: 140 mm -Min panel width (with 150 mm length): 85 mm -Min panel width (with length 250 mm): 50 mm -Three-phase line -Voltage: 380 V -A max: 22 -Frequency: 50 Hz -Max inverter frequency: 200 Hz -Control voltage: 110 V -Motor power: 15 Kw - 53 A - 11 Nl/cycleedge thickness: 0.5 - 15 mm, workpiece thickness: 10 - 45 mm, workpiece overhang: 25 mm, feed: 10 - 20 m/min, Approx. Onsite Dimension. (l x w x h): 6,300 x 1,450 x 1,450 mm, weight approx.: 2,550 kg

Description: Position: 1 SubFamily: Edgebander BATCH 1 Brand: BIESSE Model: STREAM B1 10.5 MDS Type of edging Thin edge Thick edge Gluing System EVA Hotmelt  ,  ,  ,  ,  ,  ,  ,  ,  ,  ,  ,  ,  ,  ,  ,  ,  ,  , Premilling Unit , Corner Rounding Unit Grooving Unit , Maximum panel thickness 60 mm Max. panel height 60 mm Min. panel length 150 mm Min. panel width 65 mm Min. edge thickness 0.3 mm Max. forward feed speed 25 m/min Pressure with rubber belt Panel support guides , with positioning by NC , Infeed panel alignment system , MDS No. Panel Sizing / Milling units Unit : pre-milling unit automatic timed intervention Edge coil magazine , no. positions 12 glue pot for EVA hot melt glue , premelter for EVA hot melt glue , no. pressure roller 4 with positioning by NC , No. Edge Process ...

Technical details: - Premilling Unit - Corner Rounding Unit - Maximum panel thickness: 65 mm - Operating Units: 9

Description: - Edge banding machine - Serial number 37082 - Total installed power 32 KW - Edge thickness in strips up to 20 mm - Edge thickness in the roll from 0.30 mm to 3 mm - Workpiece thickness from 10 mm up to 60 mm - Adjustable feed speed from 10 m/min up to 24 m/min - Feed motor 5.50 KW - Motorized height adjustment - CNI control - Joint cutting unit, 2 x motor - Edge feeder for strips and roll, edge magazine for one edge roll - NORDSON MC 12 gluing unit for PUR adhesive - Pressure unit with (1+6) rollers - Snipping unit, 2 x motor - Rough trimming unit, 2 x motor (upper motor missing) - Fine trimming unit, 2 x motor 0.65 KW-12000 rpm - Profile trimming unit, 2 x motor - Profile scraper unit - Trimming unit swivels from 0° to 90°, motor 3 KW-3000 rpm - Flat scraping unit - Edge buffing unit, 2 x motor - Hot air blower unitApprox. Onsite Dimension. (l x w x h): 10,700 x 1,250 x  ...

Description: Max. panel height 60 mm Max. edge thickness 3 mm Pressure with rubber belt NO. PANEL SIZING / MILLING UNITS Unit : pre-milling unit Constructor model : RT20 motor power : 2 KW r.p.m. : 9000 RPM Edge coil magazine no. positions 6 Gluing system yes glue pot for EVA hot melt glue premelter for EVA hot melt glue no. pressure roller 3 No. Edge Processing Units 5 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming Constructor model : IT90 no. motors : 2 motor power : 0.35 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 2 Processing Unit : top and bottom rough trimming Constructor model : RS10 no. motors : 2 motor power : 0.75 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 3 Processing Unit : fine trimming to trim and round Constructor model : RF10 no. motors : 2 motor power : 0.35 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 4 Processing Unit : edge scraping Constr ...

Description: Max. panel height 60 mm Max. edge thickness 3 mm Max. forward feed speed 24 m/min Top pressure , NO. PANEL SIZING / MILLING UNITS , Unit : pre-milling unit Constructor model : RT20 automatic timed intervention : , motor power : 2 KW r.p.m. : 9000 RPM Edge coil magazine , no. positions 6 glue pot for EVA hot melt glue , premelter for EVA hot melt glue , Roller set to press the edge , NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming Constructor model : IT90 no. motors : 2 motor power : 0.35 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 2 Processing Unit : top and bottom rough trimming Constructor model : RS10 no. motors : 2 motor power : 0.75 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 3 Processing Unit : fine trimming to trim and round Constructor model : RF10 no. motors : 2 motor power : 0.37 KW r.p.m. : 12000 RPM NO. EDGE PROCESSI ...

Description: serial number: 36789 Technical specifications: total installed power 33 kW, 63A, 50Hz panel length - min 150 mm - max 3200 mm panel width - min 120 mm - max 3200 mm panel height -min 10 mm - max 60 mm edge thickness in the roll from 0.30 mm to 3 mm workpiece thickness from 10 mm up to 60 mm edgebanding strip height - min 15 mm - max 65 mm working line height 950 mm panel projection from drive belt 50mm adjustable feed speed from 10 m/min up to 24 m/min motorized height adjustment CNI control, display replaced with a flat screen anti adhesive spraying device joint cutting unit, 2 x motor 5kW, 12.000 rot/min edge feeder for roll, edge magazine for two edge rolls gluing unit for EVA adhesive, granulated 2 gluing units: 1 unit that apply the glue on the panel edge and 1 unit wich apply glue on the edge, for softforming applications. These units must change depending on the des ...

Description: Max. board thickness 15 mm, max. solid wood height 50 mm, min. panel length 150 mm, min. workpiece width 50 mm, max. feeding speed 20 m/min, total power 10 KW, Glueing unit complete with edge press rollers End cutting unit Trimmer unit Edge trimming unit Edge scraper unit Brush unitApprox. Onsite Dimension. (l x w x h): 4,500 x 1,200 x 1,450 mm, weight approx.: 1,200 kg

EDGE BANDING machine BIMATIC B 220 IR-S second hand machine for edging veneer, PVC, Abs , wood volt. 220 ( 3 phases ) . by applying a 9 kW electric transformer the machine operates at 380 volts. composed by : 1. glue pot 2. edge cutting shear 3. end trimming unit 4. trimming unit / tilting chamfering unit technical details : edge thickness min. / max. mm. 0,4 / 10 panel height mm. 60

BRANDT KDF 660 Profiline single-sided edge banding with joint milling, pre-milling, fine milling, 2-fold corner copying, radius drawing blade, flat-drawing blade and babble units Type: KDF 660 Profiline Specifications: BRANDT KDF 660 Profiline with joints and corner rounds Preheating of the tool stucco IR preheating Edge thickness 0,4 - 15mm Banding height max. 66 mm, with program high adjustment Caps from the roll at 3mm thickness max 45mm height or 0.8 65mm Plate thickness max. 8-60 mm for corner copying max 40mm Control PC20+ link control (loss of contact), with modem for remote service/maintenance 1. Joint unit program Adjustment of the infeed line 2. Bandkapmesser 3a. Radiant heater High-strength bonding by workpiece preheating 3b. Spray anti-adhesive 3c. Quickmelt Glue Mel Mel Application Unit with Quick Change 3d. Leimangabe by means of glue rol ...

Description: Max. panel height 50 mm Min. panel width 70 mm Min. edge thickness 0.4 mm Max. edge thickness 3 mm Max. forward feed speed 10 m/min Pressure with idle wheels Panel support guides NO. PANEL SIZING / MILLING UNITS Unit : pre-milling unit Edge coil magazine Gluing system glue pot for EVA hot melt glue Roller set to press the edge no. pressure roller 3 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming no. motors : 2 motor power : 0.18 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 2 Processing Unit : fine trimming to trim and round no. motors : 2 motor power : 0.27 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 3 Processing Unit : Corner rounding NO. EDGE PROCESSING UNITS 4 Processing Unit : edge scraping NO. EDGE PROCESSING UNITS 5 Processing Unit : glue scraping Control system PLC Safety standard CE markApprox. Onsite Dimension. (l x w x h): 1 x 1 x 1 mm, weight app ...

Key data: 3 mm, 50 mm, 4150 mm

I am selling a fully equipped edge banding machine BRANDT Ambition 1220, built in 2010: Configuration: Manually adjustable entrance stop Manually adjustable joint milling Edge Banding EVA Glue Manually adjustable material pressure zone Pneumatically adjustable cross-cut saws Radius milling top + bottom manually adjustable Round unit 1 motor manually adjustable Radius scraper R2 pneumatically shut-off Control panel Working height adjustable by servo motor Material height 8-50mm Edge material thickness 0.4-3mm Feed speed 10m/min. Overall length including feed plate 4150mm Total weight 1320kg Very good condition, fully functional!

Edge banding machine with joint/form milling machines Brandt Highflex 1220 FC YOC 2015 Workpiece thickness 8 - 60 mm Edge thickness 0.4 - 3.0 mm Feed speed 10 m/min Joining Milling – DIA Tools Gluing unit Contact heating shoe Pressure zone Pneumatic Package Cross-cut unit Flush milling unit Profile drawing blade unit Schwabbelaggregat Electronics control Machine length 4200 mm Machine dimensions W x H 1300 x 2180 mm Weight 1400 kg

Description: Type of edging Thin edge Thick edge Solid wood Gluing System EVA Hotmelt Premilling Unit yes Corner Rounding Unit yes Max feed speed 14 m/min Maximum panel thickness 60 mm Operating Units 8 nr Min. panel height 8 mm Max. panel height 60 mm Min. panel width 70 mm Min. edge thickness 0.3 mm Max. edge thickness 3 mm Max. forward feed speed 14 m/min Top pressure yes Pressure with idle wheels Panel support guides yes with positioning by NC yes No. Panel Sizing / Milling units 1 NO. PANEL SIZING / MILLING UNITS 1 Unit : pre-milling unit automatic timed intervention : yes motor power : 2.2 KW Lamps to preheat the side of the panel yes Edge coil magazine yes no. positions 1 Gluing system yes glue pot for EVA hot melt glue yes premelter for EVA hot melt glue yes Roller set to press the edge yes no. pressure roller 3 with positioning by NC yes No. Edge Processing Units 6 NO. EDGE PROC ...

Description: Max. panel height 55 mm Min. edge thickness 0.4 mm Max. edge thickness 12 mm Max. forward feed speed 13 m/min Pressure with idle wheels NO. PANEL SIZING / MILLING UNITS Unit : pre-milling unit automatic timed intervention motor power : 2.2 KW Edge coil magazine glue pot for EVA hot melt glue premelter for EVA hot melt glue Roller set to press the edge no. pressure roller 4 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming no. motors : 2 automatic timed intervention motor power : 0.35 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 2 Processing Unit : fine trimming to trim and round no. motors : 2 motor power : 0.55 KW r.p.m. : 11300 RPM NO. EDGE PROCESSING UNITS 3 Processing Unit : Corner rounding no. motors : 2 motor power : 0.4 KW NO. EDGE PROCESSING UNITS 4 Processing Unit : glue scraping NO. EDGE PROCESSING UNITS 5 Processing Unit : buffing no. motors : 2 motor  ...

Edge glue Brandt Type: KD 86 Built: 1993 Edge thickness up to 12 mm Glueing of roll up to 3 mm with pneumatic cross-cut station Glued part with Quickmelt pre-melting tank Heavy pressure zone with one driven and three reprint rollers Saw cutting station for the front and rear overstanding Milling station flush / chamfer Second milling station radius milling R 3 mm Corner copying with pass Radius drawing blade R 3 mm Chip catching box Schwabbelstation Pneumatic package for post-processing agregates Extendable support for large parts Control panel at eye level Space requirement approx. 6100 mm

One-sided edge gluing machine in right version for hot melt adhesive gluing. equipment: - Glued part for hot melt adhesive granules - Autom. Edge magazine with roller plate - Pre-cap scissors - Pressure zone with hooded pressure roller and 2 trailing rollers - centrally adjustable upper pressure - Cap unit 2 x 0.27 kW - Büdig milling unit 2 x 0.35 kW - Drawing blade unit for PVC edges (chamfers/rounds of pre-milled PVC edges) - Swib ledunit 2 x 0.18 kW specifications: Edge thickness 0.4 - 5 mm Roller separation max. 3 x 30 mm (PVC) or 0.8 x 60 mm Workpiece thickness 10 - 50 mm Workpiece width min. 70 mm Workpiece length min. 160 mm Feed 11 m/min. Electric400 Volt - 3 Ph. - 50 Hz Connection value approx. 5 kW Pneumatic connection 6 bar Total length 4000 mm Weight approx. 1050 kg

Edge banding machine Brandt Optimat KDF 1600 GC YOC 2009 Edge thickness 0.4 - 12 mm Plate thickness 8 - 60 mm Feed 12 m/min Inlet ruler adjustable Pneumatic package Automation package Quickmelt Premelting Unit Joining milling unit 2 x 2.2 kW Cross-cut unit chamfer / Straight 2 x 0.35 kW Milling unit 2 x 0.55 kW Mould milling unit 2 x 0.35 kW (2 units) Drawing blade unit with quick-change heads Surface drawing blade for glue joint Schwabbelaggregat 2 x 0,18 kW Electronics control Connection value 11.5 kW Machine length approx. 6600 mm Weight 2900 kg

Description: Type of edging Thin edge Thick edge Gluing System EVA Hotmelt Premilling Unit yes Corner Rounding Unit yes Max feed speed 11 m/min Maximum panel thickness 50 mm Operating Units 8 nr Min. panel height 8 mm Max. panel height 50 mm Min. edge thickness 0.4 mm Max. edge thickness 3 mm Max. forward feed speed 11 m/min Top pressure yes Panel support guides yes No. Panel Sizing / Milling units 1 NO. PANEL SIZING / MILLING UNITS 1 Unit : pre-milling unit automatic timed intervention : yes motor power : 2.2 KW Edge coil magazine yes no. positions 1 Gluing system yes glue pot for EVA hot melt glue yes Roller set to press the edge yes no. pressure roller 3 No. Edge Processing Units 5 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming no. motors : 2 motor power : 0.18 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 2 Processing Unit : top and bottom rough trimming no. motors : 2  ...

Description: Type of edging Thin edge Thick edge Solid wood Gluing System EVA Hotmelt Corner Rounding Unit yes Max feed speed 11 m/min Maximum panel thickness 55 mm Operating Units 7 nr Min. panel height 8 mm Max. panel height 50 mm Min. edge thickness 0.4 mm Max. edge thickness 8 mm Max. forward feed speed 11 m/min Top pressure yes Pressure with idle wheels Panel support guides yes No. Panel Sizing / Milling units 1 NO. PANEL SIZING / MILLING UNITS 1 Unit : pre-milling unit automatic timed intervention : yes motor power : 2.2 KW Edge coil magazine yes no. positions 1 Gluing system yes glue pot for EVA hot melt glue yes Roller set to press the edge yes No. Edge Processing Units 5 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming Constructor model : HL 6130 no. motors : 2 motor power : 0.18 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 2 Processing Unit : fine trimming to trim  ...

Description: Brand: Brandt Type: KDF 210 Year of construction: 2014 Machine number: 0-261- 20-7902 Control: Easy Control 10+ Speed-controlled track control with optical start-stop indication sensors Control screen: LCD, 4 lines of text, ergonomically integrated on the input side on the hood Configuration: Chain conveyor transport Central lubrication Upper pressure/ guidance: via central adjustment with 2 rows of rollers positioned offset to each other Joint cutters: (2x) 0.75 kW, 200 Hz Diamond-tipped tool, manual positioning (Siko counters), max. 3 mm overhang and max. 40 mm workpiece thickness Glue unit: A3 glue unit for hot-melt and possibility for PU glue application Glue output roller under workpiece in following or counterflow mode Heavy-duty cutter Pressure zone: Pneumatically driven 1st pressure roller, 2nd roller running freely ensures good compaction Hacksaws: (2x) 0.18 kW,  ...

Description: Machine-nr.: 0-261-26-5028 Control: EC 10+ Speed-controlled control with optical start-stop indicator sensors Operating switch: ergonomic LCD switch mounted on the head Border thickness: 0.3 mm / max. 8.0 mm Band cutting device: 0.4 - 3.0 mm (Max. 3.0x30 mm / 1.0x55 mm) Band width edges: max. (1x) 55 mm / (3x) 45 mm Workpiece thickness: 8 - 50 mm . Workpiece width: min. 60 mm Workpiece overhang: min. 38 mm Performance: 11 m/min Workpiece pre-heating Roll magazine: Max. ø800 mm Cut-off shear: 3 mm Glue aggregate1: Hot melt granule Glue pot under glue output roller Gluing roller in travel or - in counterflow Glue aggregate 2: Airteq Hot-Air glue aggregate Pressure zone: Pneumatically driven (1st pressure roller, 2nd roller running freely ensures good compaction) Air supply units: (2x) 2.2 kW, 200 Hz Includes mounted DIA cutters Gluing unit: workpiece preheating Pressure zone ...

Description: BRANDT KDF 660 Profiline with joint cutter and corner rounder PU glue (and hot melt glue) Workpiece preheating: IR preheating Edge material: 0.4 - 15.0 mm Max. width of edgebanding: max. 66 mm (at 1 mm band thickness) Edging material on the roll: Max. 6 mm to 45 mm, max.0.8 to 65 mm Workpiece thickness: Max. 8-60 mm Control: PC20+ Streckensteuerung with modem for teleservice 1. Joint milling 2. Chopping knife 3a. Pre-activation with IR heating 3b. Anti adhesive spray device 3c. Pre-melter, for quick change of adhesive 3d. Glue aggregate with glue application roller in follow-on or counterflow 3e. Program-controlled pressure zone 4. Capsaws - adjustable 0° - 15° 5a. Coarse milling (Bündig milling) -radial Milling units with 2-point adjustment, flat, phase radius up to 12 mm edge thickness 5b. Fine milling, with program-controlled adjustment for thickness, plane, phase or r ...

I am selling a fully equipped edge banding machine BRANDT ProfiLine KDF 790, built in 2006: Configuration: Input stop can be adjusted by menu Manually adjustable joint milling Edge banding with preheating tank Material pressure zone can be adjusted by servo motor Pneumatically adjustable cross-cut saws Heavy milling at the top + at the bottom manually adjustable Radius milling top + bottom servo motor adjustable Groove saw unit at the bottom Round unit 2-motor servo motor adjustable Radius scraper blade R2 pneumatically adjustable / second set R1 included Scraper blade surface Polishing brushes Separator injection at the front Clean injection at the rear Working height adjustable by servo motor Material height 6-60mm Edge material thickness 0.4-12mm Feed speed up to 20m/min. Overall length including feed plate 7860mm Mileage status 1,650,000 meters glued. Incl ...

Description: Type of edging Thin edge Thick edge Solid wood Gluing System EVA Hotmelt Max feed speed 9 m/min Maximum panel thickness 50 mm Operating Units 4 nr Min. panel height 8 mm Max. panel height 50 mm Min. edge thickness 0.4 mm Max. edge thickness 3 mm Max. forward feed speed 9 m/min Top pressure yes Pressure with idle wheels Panel support guides yes Edge coil magazine yes no. positions 1 Gluing system yes glue pot for EVA hot melt glue yes Roller set to press the edge yes no. pressure roller 3 No. Edge Processing Units 3 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming no. motors : 2 motor power : 0.18 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 2 Processing Unit : fine trimming to trim and round no. motors : 2 motor power : 0.27 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 3 Processing Unit : glue scraping Safety standard CE mark yes Total installed power 3.5 KWA ...

Edge gluing machine Brandt Type: KTD 14 Built: 1996 Edge gluing machine with direct glue indication for gluing Edge materials on straight workpieces. Processing units: Install Glue indication Roller separation Flush milling Caps Workpiece thickness 10 - 40 mm Edge material thickness 0.4 - 1.2 mm Workpiece width min. approx. 50 mm Workpiece length min. approx. 260 mm Feed 6 m/min. Operating voltage 400 V+/- 10% - 3 Ph - 50 Hz Heating capacity 1.2 kW Connection value 3.04 kW Electrical connection cable length approx. 4.5 m Compressed air connection 7 bar Operating pressure 6 bar Weight: approx. 150 kg Space requirement: approx. 1800 x 1600 mm

Key data: 8 mm, 50 mm, 5860 mm

I am selling a fully equipped edge banding machine BRANDT Optimat KDF 550 C, built in 2006: Configuration: Manually adjustable entrance stop Manually adjustable joint milling Edge banding EVA Material pressure zone can be adjusted by servo motor Pneumatically adjustable cross-cut saws Radius milling top + bottom manually adjustable Round unit 2 motor manually adjustable Radius scraper R2 pneumatically shut-off Scraper blade surface Polishing brushes Control panel Power Control PC20+ Working height adjustable by servo motor Material height 8 - 50mm Edge material thickness 0.4 - 8.0mm Feed speed 11m/min. Assembly length including feed plate 5860mm Total weight 2660kg Very good condition, fully functional!

Description: Workpiece and edge parameters Workpiece width min: For workpiece thickness 8-22 mm | 70 mm For workpiece thickness 23-40mm | 120 mm For workpiece thickness 41-60mm , 150 mm depending on the workpiece length Workpiece protrusion | 38 mm Workpiece thickness | 8 - 60 mm Max. edge height = workpiece height, + 6 mm Edge material roll / 0.4 - 3 mm Edge cross-section max. For PVC | 135 mm For veneer | 100 mm Max. roll diameter , 830 mm Edge material strip , 0.4 - 15 mm (or 12 mm) (When using the VKNR 4845 exchange trimming unit, the max. edge thickness is 12 mm!) Max. edge cross-section For strips ' 600 mm If no radius is specified, R=2 mm is retracted and delivered serial number: 0-261-20-5413, workpiece thickness: 8 - 60 mm, feed: 8 - 18 m/min, joint trimming unit: 2 x 2,2 kW, gluing unit: A12, snipping unit: 2 x 0,35 kW, rough trimming unit: 2 x 0,55 kW, profile trimming  ...

Single-sided edge banding machine Brandt type OPTIMAT KDF 650 C edition Specifications: • Feed rate (m/min.): 8 - 18 • Feed max. with form milling machine (m/min.): 14 • Working height (mm): 950 • Pneumatic connection (bar): min. 6 • Overall length (mm): 6,060 Workpiece and edge parameters: • Workpiece width min. at workpiece thickness 8 - 22 mm: 70 mm (depending on workpiece length) • Workpiece width min. for workpiece thickness 23 - 40 mm: 120 mm (depending on workpiece length) • Workpiece width min. at workpiece thickness 41 - 60 mm: 150 mm (depending on workpiece length) • Workpiece protrusion (mm): 38 • Workpiece thickness (mm): 8 - 60 • Edge height max. = workpiece height (mm): + 6 • Edge Material Roll (mm): 0.4 - 3 • Max. edge cross-section for PVC: 135 mm² • Max. edge cross-section for veneer: 100 mm² • Roll diameter max. ( ...

Equipment: - Quick-change gluing part for hot melt adhesive - Autom. Edge magazine with roll plate - Pressure zone with pneum. pressurized pressure roller and 2 free-running repressure rollers - Power Control PC 20+ control - Inlet ruler adjustable - Joining milling unit 2 x 2.2 kW - pneum. Adjustment caps, drawing blade, program adjustment side button rollers and pneum. 2-point adjustment vertical probe rollers - Cross-cut unit 2 x 0.18 kW - Milling unit 2 x 0.55 kW - Mould milling unit 1 x 0.35 kW - Drawing blade unit for PVC edges - Surface drawing blade glue joint - Cleaning agent specification workpiece - Schwabbelaggregat Specifications Edge thickness 0.4 - 8 mm Roller cutting max. 3 x 45 mm or 0.8 x 65 mm Workpiece thickness 8 - 60 mm Feed max. approx. 11 m/min. Electrics 400 V - 3 Ph. - 50 Hz Connection value approx. 10.5 kW Pneumatic connection 6 bar To ...

Equipment: - Quickmelt gluing part for hot melt adhesive - Automatic edge magazine for rolls and fixed lengths - Heavy pressure zone with driven, pneumatically applied main pressure roller and 2 free-running repressure rollers. (adjustable by program) - motor-adjustable upper pressure. - Control panel on the machine inlet. - Electronic control power control PC 20+ - Feed variable 8-14 m/min - PU overpressure rollers - Inlet ruler adjustable by program - Joining milling unit 2 x 2.2 kW - Bevel cross-cut unit/straight 2 x 0.18 kW - Milling unit 2x0.55 kW (adjustable by program) with multiple roller pressing - Mould milling unit top+bottom, 2 x 0.35 kW - Drawing blade with quick-change heads and additional device for pointed workpieces - Glue joint drawing blade - Schwabbelaggregat - Automation package for 1-milling machines, consisting of: 3175 - Pneumatic Adjustment Caps ...

Equipment: - Quick-change Quickmelt gluing part for hot melt adhesive. - Automatic edge magazine with roll plate and autom. Edge feeder - extended inlet ruler, adjustable - heavy pressure zone (with pgroamm adjustment) with a driven main pressure roller, as well as 3 repressure rollers - Motor-adjustable upper pressure. - Control panel on the machine inlet. - Electronic control PC 16 - Modem for remote service and remote maintenance - Noise protection cladding - autom. Chain track central lubrication - Interface for return (electronic) DAHR01/02/15 Aggregate assembly - Release agent specification workpiece - Joining milling unit 2 x 2.2 kW - Cross-cut unit 2 x 0.35 kW, pneum. Adjustment chamfer/straight - Milling unit 0-25 degrees, 2 x 0.55 kW counter-rotation, to flush milling machine, pneum adjustable pneum. 2-point adjustment Vertical probe rollers - Milling unit ...

Equipment: - Machine stand throughout - Fixed stop side right - Paint finish Grey RDS 240 80 05 - Inlet ruler motorically adjustable, extended by 300 mm - Inlet lock pneumatically controlled - automatic edge feeder - Upper pressure: belt upper pressure - Height adjustment motorized - Position display and input centrally via the controller - Transport chain with rubber support, 80 mm wide - automatic central lubrication for the transport chain - Workpiece support in scissor design, approx. 1000 mm extendable - Noise protection equipment - Hood interior lighting 3 lamps - Control Power Control PC20+ Aggregate technology: - Joining milling unit 2 x 2.2 kW 200 Hz (60 mm joining milling cutter set) - Gluing unit A15 (workpiece preheating, QA34 application unit, infrared adhesive activation, magazine for rolls and fixed lengths, pressure zone with motorized adjustment, driv ...

for bill of exchange order unit

Brand 1110F - KDF110 Optimat Brand: Brandt Type: KDF 110 Year of construction: 2015 M-No.: 0-261-20-5386 Control: Easy Control 10+ Non-contact route control Feed controlled with start-stop optic-indicative sensors Screen: LCD, 420 letters, 4 program memories Configuration: Chain conveyor feed: Standard equipment with central lubrication for the transport chain. Top pressure rollers/product guidance: Zentra control, 2 roller conveyors positioned opposite each other Joint milling unit: 2 x 0.75 KW 200 HZ Including joint milling set in DIA design, with manual positioning via Siko counter, max. 3 mm removal and max. 40 mm workpiece thickness Gluing unit: A3 gluing part for hot melt glue and possibility for PU application, magazine, pressure zone with electro-pneumatic 2 point positioning via central control Pressure zone: 1st roller driven and 2 rollers running freely fo ...

Brand 1210F - KDF210 Optimat Brand: Brandt Type: KDF 210 -1210F Year of construction: 2014 Control: Easy Control 10+ Non-contact route control Feed controlled with start-stop optic-indicative sensors Screen: LCD, 420 letters, 4 program memories Configuration: Chain conveyor feed: Standard equipment with central lubrication for the transport chain. Top pressure rollers/product guidance: Zentra control, 2 roller conveyors positioned opposite each other Joint milling unit: 2 x 0.75 KW 200 HZ Including joint milling set in DIA design, with manual positioning via Siko counter, max. 3 mm removal and max. 40 mm workpiece thickness Gluing unit A3 gluing part for hot melt glue and possibility for PU application, magazine, pressure zone with electro-pneumatic 2 point positioning via central control Pressure zone: 1st roller driven and 2 rollers running freely for good and con ...

Description: COMPOSITION: Anti-adhesive group Grinding group Infrared lamp Glue tank group Pneumatic shear, pressure rollers, edge feeding system Trimming group Edge trimming group Edge scraping group Brush group TECHNICAL DATA Panel height 8 - 45 mm Edge thickness 0.4 - 3 mm (coil) / 0.4 - 5 mm (strips) Minimum panel width 95 mm Minimum panel length (edge side) 210 mm Panel feeding ,speed 7 m/min Infeed grinding motors (each) 200 Hz - 12,000 rpm - 0.75 kW Glue tank resistors 1490 W - 6 cartridges Trimming blade rotation speed 9,000 rpm Trimming motor 50 Hz - 0.18 kW Trimming motors (each) 200 Hz - 12,000 rpm - 0.22 kW Milling tools ,with WIDIA combined knives (radius/chamfer) Ø 75 mm Z4 - shaft ,Ø 16 mm (r=2 - 3 mm) Total installed power approx. 5 kW Approx. Onsite Dimension. (l x w x h): 2,450 x 800 x 1,450 mm, weight approx.: 450 kg

Cehisa EP-7 Edge Lijmer Brand: Cihesa Model: EP-7 Product gegevens: Edge thickness: 0.4 - 3.0mm (massief 5.0 mm) Banding height 10 - 60 mm Roll ø750 mm Panel thickness max. 8-60 mm Min. workpiece length: 120 mm Min. workpiece width: 75 mm Machine data: Control: Relay control 1. Tape capping 2. Gluing part 3. Cross-cut saw with HF motor 4. Flush milling - radius milling unit Feed: 10 m/min. Tool support radius mm Suction: MM Afzuig capaciteit: m³/hour Compressed air: 6 - 7 bar Dimensions LxWxH 2.9 1.2 1.5 mm (incl. plate 1.8 m) weight: 750 KG Electricity: 5,1 KW

I sell a new edge banding machine Cormak EBM300, year of construction 2022: LCD touchscreen display for setting the machine parameters and aggregates ON/OFF connection. Top feed belt 6 m/min. Element height 10 - 50 mm Edge thickness 0.4 - 3 mm  edge banding,  Sawing the final cut Radius R2 Milling Polishing brushes Total weight 400kg Length 2,30m (including edge plate 2,60m)! Feed zone only 1.30m long, convenient for the smallest workshop, or as an additional machine for edge banding the small work stucco quantities. New machine including warranty ratios, possible to try ! Full documentation and CE included. Available the same.

Hot air moulded part edge banding machine, pre-coated edges, Roller separation, stencil preference, second blower for edge heating.

The plant description will follow in the coming days

Description: Serial n°: 200.07.006.15 maximum adhesive thickness in 10 mm maximum panel thickness 60 mm maximum thickness of rolled material 3 mm minimum piece length 140 mm minimum workpiece width 70 mm maximum feed rate 12 m/min electric height adjustment pre-heating zone granular gluing system glue container below the food chain changeable glue tank suitable for PUR glue spraying system straightening unit End cutting unit 2 motors flush/radial/bevelling stations 1 Edge copying unit 1 motor scraping unit Edge scraper, Flat scraper polishing unit strip magazine synchronised aggregate NC axis(es) machine model from left to right machine length in 5.140 mm FORMAT 4 E-MOTION control Loading cost to be definedserial number: 200.07.006.15, edge thickness: 10 mm, workpiece thickness: 60 mm, feed: 12 m/min, control: FORMAT 4 E-MOTION, total power approx: 11 kW, Approx. Onsite Dimension. (l x  ...

Equipment/technical data: - Support plate for rolls - Gluing part with glue basin and pressure zone - Impact scissors - Cross-cut saw unit - Flush and radius milling unit - Pulling blade unit - Polishing unit with spraying unit - Hair dryer unit - Machine operation via touch screen - Workpiece width min. 60 mm - Workpiece length min. 140 mm - Workpiece thickness 10 - 55 mm - Roll material from 0.4 - 3 mm thickness - Strip material up to 8 mm thick - manual upper pressure adjustment by hand crank - Dimensions: 4,163 x 750 x 1,480 mm - Suction connection Ø 2 x 120 mm - electr. Connection: 400V; 50Hz; 12kW; 40.5A Technical data subject to actual equipment

Equipment/technical data: - e-Motion control with 21" smartouch instead of 10" tempora F 800 Ser - Upper pressure beam motor-controlled, adjustable workpiece height 8-60 mm - Chain feed 12 m/min, 1.5 kW, Minimum workpiece length 140 mm - Turntable edge magazine for roll edge material 0.4 - 3 mm and strip magazine for 12 pieces 10 mm edges - Edge feeding for roll and strip material - pneum. Controlled gluing unit, Teflon-coated, for 1.5 kg EVA granules, with synchronized glue roll and quick-change system. (for PUR adhesive processing, taking into account the Adhesive processing guidelines) - Pneumatically operation-controlled pressure unit e-motion (one driven, two conical contact rollers) tempora 60.12/2: 0-12mm - Impact shears for roll material - Cross-cut saw with 2 motors - Joining milling unit 2 x 1.5 kW - Upper and lower combination milling unit, 0.75 kW each, flush a ...

The workpiece return transport consists of an air cushion table with pneumatic tilting movement, complete with pusher, return conveyor with motorised belt and a not-driven roller conveyor. The panel comes out of the edge banding machine onto the air cushion table which tilts over and drops it, with the aid of the pusher, onto the return belt, situated at a lower level. The air cushion table has transfer belts to takeover the parts from the edge banding machine. Dimensions of air cushion table 1.200 x 2.400 mm Belt width 1.300 mm Installed power 3 kW workpiece return transport is deliverable for basic edge banding machine length 3.500 up to 12.500 mm

SPECIFICATIONS: Workpiece thickness max mm: 60 Edge material thickness mm: min 0.5 - max 3.0 Minimum radius border min mm: 20 Solid wood max mm: 8 Cutting scissors CW: 2.5

Approx. Onsite Dimension. (l x w x h): 3,100 x 900 x 1,650 mm, weight approx.: 1,000 kg

Description: serial number: 201011RX000004 machine type: monolateral, left side total installed power 21,8 KW, 59A, 50Hz panel length - min 120 mm panel width - min 60 mm panel height -min 10 mm - max 60 mm edge thickness in the roll from 0.4 mm to 3 mm edge thickness for strip: 3-16mm min length for strips: 180mm minimum distance between 2 panels: 800mm edge banding strip height - min 12 mm - max 63 mm adjustable feed speed from 10 m/min up to 20 m/min motorized height adjustment CN control, anti adhesive spraying device edge feeder for roll, edge magazine for two edge rolls gluing unit for EVA adhesive, granulated pressure unit for straight edges snipping unit, 2 x motor 0,5kw, 12.000 rpm rough trimming unit, 2 x motor 1,1 kw, 12.000 rpm fine trimming unit, 2 x motor 0.37 KW-12.000 rpm corner rounding unit, 2 x motor, 12.000 rot/min profile scraper unit  , serial number: 201011RX0 ...