Cnc tornalama makineleri

Lathe was bought fully reconditioned from a reseller in 1996 and has been used since 2010. Mechanically is in good conditions, NC is to be checked.

Description: Distance between points 1500 mm FAGOR display Spacing between points : 1500mm Turning diameter Ø on the bed : Ø 700 Turning diameter on carriage : Ø 600 Chuck diameter : Ø 400 Diameter of bar : Ø 82 Travels X=500 mm Z =2200 mm , Turning speed : 1250 RPM Main motor power : 25 HP No chip extractor , weight approx.: 2,700 kg, Approx. Onsite Dimension. (l x w x h): 2,700 x 1,500 x 1,360 mm

turning diameter: 430 mmturning length: 1000 mmcontrol: CNC turning diameter over bed slide: 277 mmspindle passage: 30 mmnumber of spindle speeds: 30 - 2800 U/minx-axis: 240 mmz-axis: 700 mmweight of the machine ca.: 3,0 tdimensions of the machine ca.: 2,5 x 1,9 x 1,9 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: 320 mmturning length: 400 mmcontrol: FANUC 21i-T swing diameter over face slide: 165 mmnumber of spindle speeds: 50-4500 weight of the machine ca.: 3 twww.marcels-maschinen.ch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Control: Sinumerik 840 Dsl Number of spindles: 1

Description: Control: Siemens Sinumerik 840 D Travel paths: Z-axis: 220 mm X-axis: 300 mm Rapid traverse speed: 15 m/min Main spindle: Spindle hole: 26 mm C-axis (spindle, resolution): 0.01° Spindle speed: 100 - 8000 rpm Spindle power: 7 kW Rear spindle: Max. speed: 6000 rpm Power: 6 kW Voltage: 50 Hz 3x 400 Volt Total power required: 10 kW Incl. documentationweight approx.: 2,600 kg, Approx. Onsite Dimension. (l x w x h): 2,700 x 1,900 x 2,100 mm

CNC Lathe Manufacturer: Benzinger Type: TNI-B8 Year of Make: 2000 Control: Siemens 840D Bar Passage: 42 mm Loading magazine: Irco 3m bar feeder Equipment: Main and sub-spindle 2 turrets Conveyor Accessories: Clamping Heads

CNC fine lathe Make: PetrolGer Type: TNL Control: Siemens 810T Built: 1991 Equipment and accessories: - Swivel loader system - Small conveyor belt - Charging-unloading gripper - Chip conveyors - Foot lever for clamping and relaxing the collet

Machine Details Stock-No. 1105-03782 Type of machine CNC Lathe - Inclined Bed Type Make BIGLIA Type B 121 S CNC Year of manufacture 1989 Type of control CNC Storage location FRANCE Country of origin other Delivery time at once Freight basis free loaded Technical details turning diameter 520 mm turning length 420 mm control fanuc ot Spindle Bore: 45 mm turning speed range - spindle 4900 rpm Rapid traverse 20/12 m/min tool taper VDI 30 tail stock MK 4 total power requirement 20 kW weight of the machine approx. 3.5 t dimensions of the machine approx. 2900x1800x1800 mm Additional information WITH FANUC OT CONTROL Tailstock 3 Jaw Chuck Chuck Chip Convoyer

BIGLIA Tower Type: B 301 B Year: 2001 Order: FANUC 18i-TB Series Max speed: 5000 RPM Spindle power: 11/15 Kw Weight: 3800kg

General Manufacturer: Biglia Type: B1200S Smart Turn 2 Year of Make: 2017 Control: Fanuc 31i-B5 Travel: X 520 mm Z 1,350 mm W 210° (+105°/-105°) Switch-on hours: 3,524 h Operating hours: 2,254 h Spindle Spindle speed: 4,000 rpm Bar Passage: 94 mm Tool Changer Tool holder: HSK63 DIN 69893 Number of stations: 40x Tool length: max. 295 mm Tool weight: max. 7 kg Dimensions and weight Dimensions: 6,377 x 2,237 x 2,646 mm Weight: approx. 9,200 kg Condition Condition: Used Functional: Tested and fully functional Other equipment and accessories included: Renishaw RMP60 stylus system Coolant gun Parts catcher Hollow spindle stop Rotating bezel ⌀ 12 – 152 mm 3-jaw chuck ⌀ 315 mm hydraulic

General Manufacturer: Biglia Type: B750Y Year of construction: 2024 Control: Fanuc i-HMI Travel: X 305 mm Y 140 mm (+80/-60) Z 860 mm Spindle Spindle speed: 3,500 rpm Spindle passage: 82 mm Turning diameter: 452 / 552 mm Turning length: 765 mm Circulation over bed: 680 mm Circulation over slide: 500 mm Revolver Number of stations: 16x Dimensions and weight Dimensions: 5,280 mm x 2,030 mm x 2,480 mm Weight: approx. 7,400 kg Condition Condition: Used Functional: Tested and fully functional Other equipment and accessories included: Electronic probe Losma Centrifugal Filter Coolant gun with separate pump Additional high-pressure coolant pump (25 bar) Oil trap Tool breakage and wear monitoring CSS function

turning diameter: 570 mmturning length: 1000 mmcontrol: Sinumerik 805 Siemensclamping length: ca 1200 mmgreates pass round over bed: 570 mmswing diameter over face slide: 365 mmturning speed range - main spindle: 3 - 2.500 min/-1power capacity - main spindel: 15 / 19 kWspindle bore: 62 mmspindle head: DIN 55027 No. 8diameter of quill: 80 mmtaper of center: MK 5 quill stroke: 190 mmtotal power requirement: 40 kVAweight of the machine ca.: 5,6 tLathe cycle controled- SIEMENS Sinumerik 805 / Simeodrive 611- 4-Jaw Chuck, Handwheel, Covering- Chip Tray & coolant- adjustable feet- approx 20 tool holders2021 Electrics/controls check by BoehringerThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Boehringer NG 200 2/2 CNC Lathe Year of manufacture 2004 from first ownership CE-Conformity Lable Control/Control Unit: Sinumerik 840D Conveyor Many various tool holders / tools PLC with Profibus peripherals - "DESINA" (Decentralized Installation System) Tool carrier at the top right and a tool carrier at the bottom right. 1 support on the upper right with 2 controlled axes - 1 support on the lower right with 2 controlled axes Turning length: 850 mm Circulation Ø over bed 600 mm Turning Ø with external tools 290 mm "Safety-integrated" A revolver (Sauter) is defective/in need of repair – can be repaired on request Tool carrier upper right with 12 cylindrical shank holders DIN69880-40x63 in radial design Tool carrier lower right with 12 cylindrical shank holders DIN69880-40x63 in radial design Main spindle direct drive Water-cooled motor spindle Ma ...

turning diameter: 290 mmturning length: 850 mmswing diameter: 600 mmcontrol: Siemens type: 840 D mmspindle passage: 103 mmturning speeds: 3000 U/minlive tooling: 3000 U/minrapid travel - grinding spindle: 25 m/mintotal power requirement: 65 kWweight of the machine ca.: 11 tdimensions of the machine ca.: mOffer price without toolsOptionally, the accessories can also be purchased: 106 steel holders for indoor and outdoor use.External machining, 20driven tools(including 10 x angle tools) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Universal CNC lathe BOEHRINGER NG 200 Manufacturer: BOEHRINGER Type [ type]: NG200 CNC double Control unit: Siemens 840D Year of construction[construction year]: 10/2001 Rotating diameter: 290 mm Turning length: 850 mm Control: SIEMENS 840 D Orbital diameter over bed: 600 mm Revolver 1 Revolver 2 Counter spindle Counter headstock Tailstock C-axis Powered tools Automatic machine doors – newly retrofitted Z-axis resolution: 40nm (2nm interpolated) Travel in Z: 740mm Rapid traverse speed in Z: 25 m/min Centering tip SK 30 X-axis resolution: 125nm (8nm interpolated) Travel in Z: 220mm Rapid traverse speed in Z: 25 m/min Distance between main and counter spindle: 1034mm Drive power: 30-72 kW Torque: 662 Nm Speed range max.: 4500 rpm Spindle head: Size 6/8 DIN 55026 Spindle diameter in the front. Bearing [spindle]: 120 mm Chuck diameter: 200-315mm Spindl ...

turning diameter: 500 mmcentre distance: 3000 mmSiemens control: Sinumerik The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

BOEHRINGER VDF DUS 1000 CNC lathe was built in 1993 in Germany. The machine, designed for machining workpieces with a maximum diameter of 1000 mm, delivers excellent turning results during even the most intensive challenges, thanks to its extremely stable design and reliable components. The spindle is driven by an stepless AC motor, which allows efficient turning in two different, optimally adapted speed ranges. All axes, on the other hand, have powerful servo drives, guaranteeing excellent dynamics and positioning accuracy throughout the machine’s lifetime. This is rounded off by an intuitive SIEMENS CNC control with many functions for easy operation and programming. The BOEHRINGER VDF 1000 DUS lathe weighs approximately 10100 kg. Technical specifications of BOEHRINGER VDF DUS 1000 metal lathe - turning diameter above the bed: 1000 mm - turning diameter over transverse slide: 710 ...

Description: The machine is equipped with: a three-jaw chuck , a tailstock , as well as available documentation serial number: 2012.1174-01, x-motion: 420 mm, z-motion: 1,000 mm, control: SIEMENS SINUMERIK 840, toolchanger positions: 8, number of controlled axes: 2, spindle bore: 45 mm, turning speed range: 3,000 rpm, total power requirement: 11 kW, weight approx.: 6,000 kg, Approx. Onsite Dimension. (l x w x h): 5,000 x 2,000 x 1,900 mm

Dear Ladies and Gentlemen, We currently have a used lathe for sale. 1 x Boehringer VDF 180 Cte lathe built in 2000 the machine is still in operation and can be visited.

Description: The machine is equipped with: a three-jaw chuck, diameter approx. 300 mm , a tailstock , as well as the tools located on the tool turret serial number: 1114.3515-24, x-motion: 370 mm, z-motion: 1,185 mm, control: PHILIPS B3T, toolchanger positions: 12, number of controlled axes: 2, spindle bore: 70 mm, turning speed range: 2,500 rpm, total power requirement: 32 kW, weight approx.: 7,000 kg, Approx. Onsite Dimension. (l x w x h): 5,500 x 2,400 x 2,400 mm

turning diameter: 140 mmturning length: 170 mmcontrol: Mitsubishi Meldas 635 spindle passage: 42 mm: 140 mmturning speed range - grinding spindle: 80 ~ 8.000 U/mindrive capacity - spindle motor: 11 / 7,5 kW: 0,001 °spindle bore: 55 mmA-Axis: turning speed range - spindle: 60 ~ 6.000 U/mindrive capacity - spindle motor: 3,7 / 2,2 kW: 42 mm: 2 posturret (x-stations): 12 : 2 x 12 pos: 45 ~ 4.500 min -1Turning Speed of the Rolls: 1 kWrapid traverse X-axis: I 24 m/minrapid traverse X-axis: II 18 m/minrapid traverse X-axis: III 20 m/minrapid traverse Z-axis: 24 m/mintotal power requirement: 14 kWweight of the machine ca.: 3,3 tdimensions of the machine ca.: 2,4 x 1,6 x 2,0 m- CNC control Mitsubishi Meldas 635LCC- Collet holder for main spindle- Pick-up spindle- Collet chuck holder for pick-up spindle- Pick-up spindle indexing- 2 12-position turrets with driven tools (VDI 20)- Warning light ( ...

CNC lathe BOLEY type BE 42 - Bi-spindle / twin-turret TECHNICAL SPECIFICATIONS: CN Type: MITSUBISHI Meldas 635LCC X1 axis stroke: 170 [mm] Z1 axis stroke: 200 [mm] X2 axis stroke: 110 [mm] Z2 axis stroke: 395 [mm] X3 axis stroke: 110 [mm] Z3 axis stroke: 170 [mm] Y-axis stroke: -/+ 40 [mm] Tool holder type: VDI 20 Spindle for clamping clamps: Size 48 DIN 6343 Spindle passage diameter: 42 [mm] Mini speed. Pin: 80 [rpm] Maximum speed. Pin: 8000 [rpm] C-axis indexing accuracy: 0.001 [°] Pin power: 7.5 [kW] Counter-spindle passage diameter: 42 [mm] Mini speed. Counter spindle: 60 [rpm] Maximum speed. Counter spindle: 6000 [rpm] C-axis indexing accuracy counter-spindle: 0.001 [°] Counter spindle power: 2.2 [kW] Maximum diameter. Machinable: 140 [mm] Number of positions - Upper turret: 12 Number of motorized positions - Upper turret: 12 Maximum speed. rotating to ...

automatic workpiece loader - max bar length: 720 mm - max dia: 65 mm Previously used on Mazak CNC lathe

two pieces of Budapesti EEN400 lathes In terms of price, our idea is 9,000.00€ per machine. Accessories would also be there, but this would still have to be checked carefully.

Inv. Num. : 6719 Type: MICROCUT SAB LT-52 Producer: Buffalo Created: 2019 Parameters: Control system: Siemens Maximum turning length: 460 mm Maximum turning diameter: 210 mm Maximum turning diameter over bed: 500 mm Maximum spindle speed: 5000 1/min Maximum turning diameter over support: 220 mm Maximum length of travel in the X-axis: 215 mm Maximum feed rate in the Z-axis: 520 mm Length: 3330 mm Width: 1821 mm Height: 1930 mm Weight: 3200 kg Equipment: Chuck Conveyor Top

- X: 1050 mm - Y: 920 mm - Z: 110 mm - table size: 1000 x 1000 mm - speed range: 18.000 rpm - taper fixture: SK 25 - tool changer: 6-station - max. workpiece dimension: Ø 65 mm, hight 65 mm - control: Bosch CC 120 - total power: 12 kW - weight of machine: 900 kg - space requirement (W x D x H): 1,7 x 1,9 x 2,0 m Details milling motor power 4 kW vacuum pump 25 m³ / h very good condition, immediately ready for use servo motors in the axes has run less than single-shift accessories 6 units with collets 14 collets vacuum pump suction with 4 m suction hose machine feet documentation tool presetting device with depth gauge PAV Vario

: 0583 mm: 1710 mm: : 0 mm: 82 mm: 436 mm: 2500 U/min : A1-8 DIN 55026 : 100 mm: 235 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: 324 mmturning length: 540 mmcontrol: Fanuc 21i-T total power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mCNC control Fanuc 21i-T3-jaw chuck12-fold turret (VDI40)tail stockchip conveyorcoolant deviceTechnische Daten: / technical detailsmax. Schwingdurchmesser / max. rotary diameter 530 mmmax. Drehdurchmesser / max. turning diameter 324 mmmax. Drehlänge / max. turning length 540 mmVerfahrweg X / travel X 245 mmVerfahrweg Z / travel Z 540 mmmax. Drehzahl / max. spindle speed 4500 UpM/rpmAnzahl der Revolverplätze / number of tool places in revolver 12 Gewicht/weight 4500 kgTechnische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich -Technical data, accessories and description of the machine are not binding.The data for this ad was created with ModulMWS - the software solution ...

turning diameter: 360 mmturning length: 400 mmcontrol: Acramatic 2100 total power requirement: kWweight of the machine ca.: 3000 kgdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

CITIZEN CINCOM A20 VIPL CNC lathe built in 2006 ensures the highest precision and efficiency in the production process. During machining, the specially designed bed with its rigid structure and high thermal stability effectively reduces the heat impact, resulting in increased machine life and reliability. All of this, combined with a modular design with a reduced number of parts, makes the CINCOM A20 VIPL CNC lathe ideal for various types of production. Workpieces with a maximum diameter of 20 mm and a length of 135 mm are machined in 7 axes by a powerful main spindle which is synchronised with an AC motor, forming an electrospindle. A bushing driven by a separate AC motor is also synchronised with the machine’s main spindle. The operator’s panel consists of an intuitive FANUC 32i CNC controller, a memory card slot and an electronic wheel located next to the monitor designed to ch ...

Description: CNC sliding headstock lathe Citizen L520 7 axes (X1/Z1/Y1/C1/X2/Z2/C2) Bar Ø max. 20 mm Turning length max. 205 mm Main spindle, max. speed 10,000 rpm, C-axis 0.001 degrees Counter spindle, max. speed 10,000 rpm, C-axis 0.001 degrees Tool holder for a total of 18 tools (linear tool holder, front attachment, rear machining) Parts conveyor belt Loading magazine FMB Turbo 3-26 The machine can be inspected by appointment.Turning length max.: 205 mm, control: Cincom Mitsubishi Meldas, number of controlled axes: 7, weight approx.: 1,750 kg, Approx. Onsite Dimension. (l x w x h): 2,550 x 1,450 x 1,850 mm

CMT Ursus/Emco Ø 500 x 1500 mm CNCSwing over bed: 500 mm Swing over cross-slide: 265 mm Distance centre tot centre: 1500 mm Max longitudinal travel Z-axis: 1500 mm Max cross travel X-axis: 240 mm Dia of spindle bore: 58 mm Power on the spindle: 7,5 kW Number of speeds: 15 > 1500 rpm Command: CMT Weight: 2 ton

Control Fanuc 32i-TB Rotary diameter. [mm] 460 Turning length [mm] 640 Main spindle: Motor spindle technology Speed (max.) 4,000 rpm Power (max.) 22 kW Torque (max.) 366 Nm Bar passage 65 mm Workpiece clamping 3-jaw chuck, SMW Autoblock 210 BB-T2 Sub-spindle: Motor spindle technology Speed (max.) 4,500 rpm Power (max.) 14 kW Torque (max.) 292 Nm Workpiece clamping 3-jaw chuck, SMW Autoblock 175 BB with Differential Compressive Stress Pneumatic Parts Ejector Travel in W 640 mm Rapid traverse in B 30 m/min Tool carrier (X/Y/Z): Technology Turret with 15 stations Tool holder BMT 55 Tool drive 12,000 rpm, 11.3 kW, 75 Nm Travel in X/Y/Z 310/120/640 mm Rapid traverse in X/Y/Z 30/15/30 m/min Equipment/accessories: Direct displacement measuring system (glass scales) in X/Y/Z Chip Management Chip Conveyor Coolant management IKZ pump with filter and high pressu ...

Technical characteristics: Year: 2012 NC Type: FANUC 31i - MODEL A Distance between mandrels: 639 [mm] Maximum diameter Machinable: 255 [mm] Permissible diameter above carriage: 270 [mm] Z1 axis stroke: 500 [mm] X1 axle stroke: 190 [mm] Y1 axis travel +/-: 40 [mm] Z2 axis stroke: 500 [mm] X2 axle stroke: 190 [mm] Y2 axis travel +/-: 40 [mm] X-axis fast feed speed: 16000 [mm/min] Z-axis fast feed speed: 20000 [mm/min] Y-axis fast feed speed: 12000 [mm/min] Acceleration of axis displacement: 1g Spindle Nose: ASA 8" A2 Maximum diameter in bar: 66 [mm] Spindle Bore: 77 [mm] Maximum speed Spindle: 4000 [rpm] Spindle power: 15 [kW] Spindle torque: 136 [Nm] Counter Spindle Nose: ASA 6" A2 Maximum diameter in sub-spindle bar: 52 [mm] Counter-spindle bore diameter: 61 [mm] Counter-spindle stroke: 635 [mm] Maximum speed Spindle: 5000 [RPM] Spindle power: 7.5 [kW] Sp ...

Inv. Num. : 7185 Type: Alpha 1350 XS Producer: Colchester Created: 2008 Parameters: Control system: Fanuc Alpha X Series Maximum turning length: 650 mm Max. turning diameter: 350 mm Maximum turning diameter over bed: 350 mm Spindle diameter: 42 mm Maximum spindle speed: 3500 1/min Length: 2400 mm Width: 1700 mm Height: 1500 mm Weight: 1800 kg Equipment: Owner

: 0460 mm: 1500 mm: : 230 mm: 78 mm: 400 mm: 2200 U/min : D1-8 DIN 55029 : 95 mm: 145 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 0 mm: 0 mm: 0330 mm: 1000 mm: : 167 mm: 40 mm: 3000 U/min : DIN 55029 D1-4 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 530 mm, 500 mm, 4000 1/min

Machine Details Stock-No. 1105-04005 Type of machine CNC Lathe Make COLCHESTER Type TORNADO 300 Year of manufacture 1995 Type of control CNC Storage location HAGUENAU FRANCE Country of origin Great Britain Delivery time immediately Freight basis EX WORK Price Technical details turning diameter 530 mm turning length 500 mm control FANUC OT total power requirement 22 kW weight of the machine approx. 3.3 t Additional information GOOD MACHINE CNC CONTROL FANUC OT Cuck Taikstock VDI 40 Turret 12 P Chip Convoyer echnical information Swing over bed 530 mm Swing over cross-slide 330 mm Distance centre tot centre 500 mm Max longitudinal travel Z-axis 20 m/min Max cross travel X-axis 10 m/min Spindle cone A2-8 Dia of spindle bore 90.5 mm Power on the spindle 22 kW Number of speeds 4000 rpm Command Fanuc Total power needed 53 kVa Length 3500 mm Wid ...

swing dia.: 440 mmmax. turning diameter: 220 mmturning length: 450 mmtravel -x axis: 200 mmcontrol: Fanuc 18i-TB max. helix angle: 60 °spindle bore: 64 mmtool taper: VDI 30 numbers of positions in the tool changer: 12 CNC Lathe | COLCHESTER - TORNADO T6MSequipped with counter spindle and chip conveyor.The machine is in a well-maintained condition.Please refer to further technical details in the attachement of the offer.- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -#Tags: T6 MS | T6-MS | T 6MS | T-6MS | T-6The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. swing diameter over bed: 510 mmmax. turning diameter: 260 mmMax. Turning length: 540 mmtravel -x axis: 240 mmcenter height over bed: 260 mmcontrol: FANUC 21i-TB spindle bore: 77,5 mmno. of tools in turret: 12 xtool taper: VDI 40 CNC Lathe | COLCHESTER - TORNADO T8The machine is in good condition.Please refer to further technical details in the attachement of the offer.A machine video will be shared on request.- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -#Tags: T 8 | T-8The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Control : D.Electron Z 32 Peak height 220 mm Tip width 1000 mm Turning over bed 440 mm Turning diameter via slide 245 mm Travel -Z Axis 750 mm Width of the lathe bed 320 mm Spindle holder CL 6" Spindle bore 62 mm Spindle speeds 0 - 2500 rpm. Rapid speed X/Z 7 m/min Pinien travel by hand 200 mm Pinole diameter 80 mm Pinole holder MK 4

Control : D.Electron Z 32 Peak height 260 mm Tip width 1500 mm Turning over bed 520 mm Turning diameter via slide 310 mm Travel -Z Axle 1250 mm Travel -X-axis 270 mm Width of the lathe bed 400 mm Spindle holder CL 8" Spindle bore 110 mm Spindle speeds 0 - 2000 rpm. Rapid speed X/Z 5 m/min Pinien travel by hand 220 mm Pinole diameter 80 mm Pinole holder MK 5 Total installed power 18 kW (Electronically reduced) Engine hours 1828 h

Control : Heidenhain Peak height 260 mm Tip width 1500 mm Turning over bed 520 mm Turning diameter via slide 310 mm Travel -Z Axle 1250 mm Travel -X-axis 270 mm Width of the lathe bed 400 mm Spindle holder CL 8" Spindle bore 110 mm Spindle speeds 0 - 2000 rpm. Rapid speed X/Z 5 m/min Pinien travel by hand 220 mm Pinole diameter 80 mm Pinole holder MK 5 Total installed power 18 kW (Electronically reduced) Engine hours 1828 h

Control : D.Electron Z 32 Peak height 220 mm Tip width 1000 mm Turning over bed 440 mm Turning diameter via slide 245 mm Travel -Z Axis 750 mm Width of the lathe bed 320 mm Spindle holder CL 6" Spindle bore 62 mm Spindle speeds 0 - 2500 rpm. Rapid speed X/Z 7 m/min Pinien travel by hand 200 mm Pinole diameter 80 mm Pinole holder MK 4

Peak height above bed 210 mm Tip distance 950 mm Permissible diameter on bed 420 mm Permissible diameter on slide 160 mm Head Spindle passage 62 mm Spindle nose ASA 6 - Type 2 Engine Power 10.7 kW Spindle bore 62 mm Speed 0 - 3500 rpm. CNC Control D. Electron Z32

CORTINI Tower – C-Axis Type: T120C/25 Year: 1998 Order: FANUC 21i-T Series

Key data: 350 mm, 1250 mm

CNC lathe Dainichi DAF 35 – F35/1250 - Built in 1994 - 1st hand and from your own use - Fully functional, energized, ready for demonstration - X-axis travel: 200 mm - Z-axis travel: 1320 mm - Turning diameter: 350 mm - Turning length: 1250 mm - Rapid traverse Z-axis mm/min 15000 - Spindle speeds: 25 – 2500 rpm - Spindle diameter 105 mm - Spindle motor power: 22 kW - Control: Fanuc 0TF - Chip conveyor Z-Type - Kitagawa 12" Hydr. 3-jaw chuck

Manufacturer: DMG Type CTX 510 Year of construction 2004 Control Heidenhain Machine weight approx. 7.5 t Tool holder VDI 40 x-travel 300 mm z-travel 1050 mm Speed range 3500 1/min Turning diameter 465 mm Turning length 1050 mm Chip conveyor: yes Tailstock KM5 Space requirement approx. 6.5 x 3.0 x 2.2 m Circulation diameter 680 mm Tool turrets - places 12 pl. Rod diameter 90 mm