Prensas de inyección de caucho

clamping force: 350 kNinjection volume: 59 cm³screw diameter: 25 mmplaten size: 400 x 400 mmCondition: used,Specification: injection moulding machine for rubber - used International size: 350-90 clamping unit:- clamping force: 350 kN- clamping platen size: 400 x 400 mm- Clear distance between tie bars: 270 x 270 mm- Mould installation height min.: 225 mm- Distance between clamping platens: max. 550 mm- Opening stroke max.: 325 mm- Ejector stroke: 125 mmInjection unit:- Screw diameter: 25 mm x 20D- Injection volume max.: 49 cm³- Injection part weight: 59 g/hp- Max. injection pressure: 1,860 bar- Screw circumferential speed: 37 m/min- Cylinder heating: 4x 900 W- Nozzle heating:  ...

clamping force: 1.300 kNinjection volume: 230 cm³screw diameter: 45 mmplaten size: 685 x 685 mmCondition: used,Specification: injection moulding machine for TPE - usedincluding Koch dosing unitclamping unit:- clamping force: 1.300 kN- heating platen size: 685 x 685 mm- Clear distance between tie bars: 470 x 470 mm- Mould installation height min.: 250 mm- Distance between platens max.: 900 mm- Opening stroke max.: 650 mm- Ejector stroke: 225 mmInjection unit:- Screw diameter: 45 mm x 18D- Injection volume max.: 230 cm³- Injection part weight: 210 g/hp- Max. injection pressure: 1,670 bar- Screw circumferential speed: 75 m/min- Cylinder heating: 4x 2,200 W- Nozzle heating: 600 W- Connection value: 3x 400 V, 50 Hz- Electrica ...

clamping force: 350 kNinjection volume: 58,5 cm³screw diameter: 28 mmplaten size: 260 x 254 mmCondition: used,Specification: injection moulding machine for TPE - usedclamping unit:- clamping unit: vertical- clamping force: 350 kN- opening stroke max.: 300 mm- platen distance max.: 500 mm- Mould installation height min.: 200 mm- Clear width between tie bars: 260 x 254 mm- Ejector stroke max.: 80 mm- Clamping unit: VV- Lift of protective bonnet: 500 mmInjection unit:- Screw diameter: 28 mm- Screw L/D ratio: 18.6- Screw stroke max.: 95 mm- Injection volume max.: 58.5 cm³- Injection pressure: 1577 bar- Plasticising flow: 8.6 g/s- Injection flow: 85.5 g/s- Connected load: 3x 400 V, 50 Hz- Max. heating power: 5.8 kW- Drive power: 7,4 kW- Total power:  ...

clamping force: 11000 kNinjection volume: 12500 cm³screw diameter: -- mmplaten size: -- mmCondition: used,Specification: injection moulding machine for rubber - used, in very good condition machine was serviced annually by manufacturerclamping unit:- Euromap (size): 11000-25600- clamping force: 11.000 kN- size of heating platens L/W/H: -- x -- x mmInjection unit:- Injection volume max.: 12,500 cm³- Injection pressure: 2050 bar- Dosing force: 118 kN- Control: Siemens S7- Connected load: 3x 400 V, 50 Hz, N- Total current: 276 A- Back-up fuse: 300 A- Pump drive: 277 bar- Driving power: 45 kW- Weight approx.: 43.8 tOperating hours approx.: 33,130 hoursThe data for this ad was created with ModulMWS - t ...

clamping force: 2700 kNinjection volume: 3300 cm³screw diameter: -- mmplaten size: 780 x 670 mmCondition: used,Specification: vertical injection moulding machine for rubber NR, EPDM, SBR, NBR, CR, etc. - used, in very good condition 6 months in useclamping unit:- Euromap (size): 2700-7200- Clamping force: 2,700 kN- Heating platen size L/W/H: 780 x 670 mm- Distance between upper and lower platen: 970 mm- Stroke min.: 420 mm- Stroke: 550 mmInjection unit:- Injection volume max.: 3,300 cm³- Injection pressure: 2,180 bar- Nozzle contact force: 80 kN- Connected load: 3x 400 V, 50 Hz, N- Back-up fuse: 125 A- Pump drive: 265 bar- Drive power: 22 kW- Pump speed: 66 rpm-  ...

clamping force: 2700 kNinjection volume: 3300 cm³screw diameter: -- mmplaten size: 780 x 670 mmCondition: used,Specification: vertical injection moulding machine for rubber NR, EPDM, SBR, NBR, CR, etc. - used, in very good condition almost unused!clamping unit:- Euromap (size): 2700-7200- Clamping force: 2,700 kN- Heating platen size L/W/H: 780 x 670 mm- Distance between upper and lower platen: 970 mm- Stroke min.: 420 mm- Stroke: 550 mmInjection unit:- Injection volume max.: 3,300 cm³- Injection pressure: 2,180 bar- Nozzle contact force: 80 kN- Connected load: 3x 400 V, 50 Hz, N- Back-up fuse: 125 A- Pump drive: 265 bar- Drive power: 22 kW- Pump speed: 66 rpm- C ...

Máquina de moldeo por inyección de caucho DESMA de 400 toneladas -Modelo: SIGMA 4000

clamping force: 250 kNinjection volume: 49 cm³screw diameter: 25 mmplaten size: 300 x 300 mmCondition: used,specification: C-frame injection moulding machine - usedclamping unit:- clamping force: 250 kN- heating platen size: 300 x 300 mm- clamping/opening stroke: 330 mm- Closing direction: from below- Lateral ejector: yes- Ejector stroke/force: 115 mm / 12 kNInjection unit:- Injection volume max.: 49 cm³- Screw diameter: 25 mm- Screw length: 16- Screw speed max.: 250 rpm- Injection: from above- Voltage: 3x 400 V, 50 Hz, N, PE- Connected load: 55 kW/92 A- Weight approx.: 3,500 kgVarious accessories are also available:- Injection unit (25 screw)- 2 heating plates- Funnel and various small partsThe data for this ad was created with ModulMWS - ...

clamping force: 450 kNinjection volume: 135 cm³screw diameter: 35 mmplaten size: 600 x 400 mmCondition: used,Specification: C-frame injection moulding machine for TPE - usedclamping unit:- clamping force: 450 kN- heating platen size: 600 x 400 mm- sliding table: yes- Clamping direction: from below- Ejector / lifter: Up + LoInjection unit:- Injection volume max.: 135 cm³- Screw diameter: 35 mm- Connected load: 3x 400 V, 50 Hz- Weight approx.: 5,500 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping force: 450 kNinjection volume: 99 cm³screw diameter: 30 mmplaten size: 860 x 320 mmclosing stroke: 406 mmCondition: used,Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083Clamping unit:- Clamping force: 450 kN- Opening travel: 406 mm- Heating plate size: 860 x 320 mm- Mould height min.: 264 mm- Max. plate spacing: 464 mm- Ejector stroke: 20 mm- Ejector force: 20 kNInjection unit:- Screw diameter: 30 mm- Screw length L/D: 16- Dosing stroke: 140 mm- Stroke volume max.: 99 cm³- Max. spray weight: 114 g- Screw speed: 20 - 300 rpm- Injection flow: 106 cm³/s- Injection flow increased: 71 cm³/s- Special injection pressure: 1451 bar- Spec. injection pressure increased: 2205 bar- Nozzle path: ...

clamping force: 450 kNinjection volume: 99 cm³screw diameter: 30 mmplaten size: 860 x 320 mmclosing stroke: 406 mmCondition: used,Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083Clamping unit:- Clamping force: 450 kN- Opening travel: 406 mm- Heating plate size: 860 x 320 mm- Mould height min.: 264 mm- Max. plate spacing: 464 mm- Ejector stroke: 20 mm- Ejector force: 20 kNInjection unit:- Screw diameter: 30 mm- Screw length L/D: 17- Dosing stroke: 140 mm- Stroke volume max.: 99 cm³- Max. spray weight: 114 g- Screw speed: 20 - 300 rpm- Injection flow: 106 cm³/s- Injection flow increased: 71 cm³/s- Special injection pressure: 1450 bar- Spec. injection pressure increased: 2210 bar- Nozzle path: ...

clamping force: 800 kNinjection volume: 78 cm³screw diameter: 25 mmplaten size: 570 x 552 mmCondition: used,Specification: injection moulding machine for LSR - used Nr. 13EN08clamping unit:- clamping force: 800 kN- size of heating platen: 570 x 552 mm- Between tie bars horizontally: 405 mm- Between tie bars vertically: 345 mm- Opening stroke: 310 mm- Ejector force: 25.4 kN- Ejector stroke: 100 mm- Mould installation height max.: 530 mm- Mould installation height min.: 250 mm- Bar diameter: 60 mm- Control: CC 90-A0Injection unit:- Injection volume max.: 78 cm³- Injection weight max.: 90 g- Screw diameter: 25 mm- Metering stroke: 160 mm- Screw speed max.: 20 - 400 rpm- Injection flow: 87 g/sec- Injection flow (increased): 64 g/sec- Sp ...

clamping force: 800 kNinjection volume: 154 cm³screw diameter: 35 mmplaten size: 570 x 552 mmCondition: used,Specification: injection moulding machine for LSR - used Nr. 13EN12 clamping unit:- clamping force: 800 kN- size of heating platen: 570 x 552 mm- Between tie bars horizontally: 405 mm- Between tie bars vertically: 345 mm- Opening stroke: 310 mm- Ejector force: 25.4 kN- Ejector stroke: 100 mm- Mould installation height max.: 530 mm- Mould installation height min.: 250 mm- Bar diameter: 60 mmInjection unit:- Injection volume max.: 154 cm³- Injection weight max.: 156 g- Screw diameter: 35 mm- Metering stroke: 160 mm- Screw speed max.: 20 - 320 rpm- Delivery flow: 35 g/sec- Injection flow: 148 g/sec- Injection flow ...

Máquina de inyección HUSKY Tipo H400 400 toneladas Presión hidráulica 180 BAR max Peso 18.143 kg Marcado CE Año: 2003

Prensa de inyección Klockner Desma 100ton Modelo: D968.100.Z0 Tamaño de la placa: 400 mm de profundidad x 500 mm de ancho Volumen de carrera 350cm3 Fuerza de sujeción 1000kN Presión de inyección 2380 bar Voltaje 3x 400 50Hz Año 1998

LWB Steinl Moldeo por inyección / Prensa de vulcanización Modelo: VCE-B Fuerza de sujeción 2500kN Volumen de inyección 1000 cm3 Aire comprimido 6 bar 75 kW Aceite hidráulico 40/45 cst Tamaño del patrón 760 x 630mm Pantalla táctil LWB Flex Qty 1 Tool Kemp modelo TT-188 (año 2019) canal caliente. Peso 12850 kgs

LWB Steinl Máquina de moldeo por inyección Modelo VCE-T-TPE-EPDM Capacidad de 100 toneladas Control de pantalla táctil ECO

LWB Steinl Moldeo por inyección / Prensa de vulcanización Modelo: VCEFE Fuerza de sujeción 2500kN Volumen de inyección 1000 cm3 Aire comprimido 6 bar 76 kW Aceite hidráulico 46/40 cst Tamaño del patrón 760 x 630mm Pantalla táctil LWB Flex Cantidad 2 Tool Kemp modelo TT-188 Año 2013 Peso 13500 kgs

LWB Steinl Moldeo por inyección / Prensa de vulcanización Modelo: VCEFE-B Fuerza de sujeción 2500kN Volumen de inyección 1000 cm3 Aire comprimido 6 bar 76 kW Aceite hidráulico 46/40 cst Tamaño del patrón 760 x 630mm Pantalla táctil LWB Flex Cantidad 2 Tool Kemp modelo TT-188 Peso 13500 kgs

Máquina de moldeo por inyección Maplan Modelo: MTF400/80C 80 toneladas Distancia de seguridad 162mm Tiempo de ejecución 81ms Seguimiento 5mm Tamaño del patrón 510mm x 410mm Control de pantalla táctil

Key data: 1500 kN, 750 cm³

Paneles 510x400 mm Fuerza de cierre 150 t Volumen máximo inyectado 750 cm³ Ancho libre 440 mm

Rep B46 Máquina de moldeo por inyección Tamaño de las placas 430x430mm Unidad de inyección de volumen corto 670cm3 Presión de inyección 1690 bar Fuerza de inyección 331kN

clamping force: 1.013 kNinjection volume: 400 cm³screw diameter: 25 mmplaten size: 335 x 400 mmCondition: used,Specification: injection moulding machine for rubber - usedclamping unit:- clamping unit: vertical- clamping force: 1.013 kN- size of heating platen: 335 x 400 mm (standard) core turning unit Injection unit:- screw diameter: 25 mm- Barrel diameter: 51 mm- Injection volume max.: 400 cm³- Injection pressure: 1,500 bar- Connection value: 3x 400 V, 50 Hz 42A fuse protection (incl. periphery)- Electrical power: 29,1 kVA- Control: G8 Control- Hydraulics: 250 bar (tank 200 litres)- Further connections: Cooling water inlet/outletDimensions L/W/H approx.: 2,300 x 3,400 x 2,250 mmWeigh ...

Prensa de inyección Yizumi Modelo: YL2-V280L Fuerza de cierre 2800 kN Volumen: 2000cc Molde de carrera abierta 500mm Altura mínima del molde 100 mm Tamaño de la platina calefactada 670 mm x 780 mm Placa calefactora luz diurna 600mm Presión de inyección 1970 bar Volumen teórico de inyección 2000cm3 Potencia de la bomba de aceite 11kW Presión del sistema 230 bar Potencia total 37kW Fuente de alimentación: 415V, 50Hz, 3P+N+PE Bomba variable Rexroth + servomotor Inovance: Año 2021 Marcado CE