We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
Trumpf Trulaser 5030 6kw CO2 Machine in constant use 2006 ...
The offer includes only the resonator. It is also possible to inspect the machine. The device is dismantled in very good condition. The offer includes manufacturers documentation in German. ...
-reliably high load capacity across the entire beam length thanks to homogeneous web material -secured component load capacity, as all of the straps are machine stress graded and load-tested -consistent product characteristics owing to high dimensional stability -multiple savings compared to squared timber due to improved load capacity combined with lower weight -Certification EN 13377 -Produced in Austria from Doka Industrie The length of the H20 smart beam varies from 2,45m until 5,90m. Costs: 5,00 EUR/rm For more information or an appointment, you can contact me at any time. Phone: + 43 664 1296830 or Email:office@berger-international.at
Qty. 1 Second-hand H-Beam production line Mfc.: Production Line: B&K Welding Machines: THERMATOOL Saw Cutting: LINCOLN Driving Part: Seoho Electric Drive: PAKER PLC: MITSUBISHI Leveller: FLATTENER Press cutter & DDS: Samyang Run-out Table: Wuchang Production range: No. Class Width (mm) Thickness (mm) Length(M) 1 Web 53 ~ 450 2.3 ~ 12.0 6.0 ~ 18.0 2 Flange 50 ~ 300 3.0 ~ 12.0 Capacity: 60,000 MT/annum Equipment total weight: approx.139 MT First installation: 10/1973 Type: Welding H-Beam Facility Welding Type: Electric Resistance Welding Cutting type: Cut-Off Saw, Presscutter Line Speed: Max. 37 m/min.
Profile bending roll used equipment hydraulic model AR200 year 2008 make MG Italy Capacity bending chart photo in enclosed -Technical data: Output shafts size 200 mm -Machine complete with set of rollers adjustable for the various shape of profiles. -Traction tool hydraulic operated for the HEB-beam - IPE - UNP bending the hard side. -Lateral correctors left and right side hydraulic operated in 3 direction. -Included additional set of rolls for pipe 6" inches -Machine with 3 rolls driven system with individual hydraulic motor and axial gear-unit on each shaft. -The 3 shafts working on bearings, heavy duty type with sealed lubrication. -Centralized control panel movable on ...
With this rotator, the workpiece can be fixed and rotated in the correct position without a crane. By using the traditional positioning can be replaced. Occupational safety and treatment are optimized and cycle times are reduced. In the best case, the time requirement can be reduced by up to 20%! Includes wired remote control and foot pedal. The device has a master-slave function, which allows several driven units to be synchronized with each other. This can be important if later the capacity should be increased. When not in use, you can simply put the device in the corner and save space. The device is easy to transport to external workstations.
ERMAKSAN LASERMAK 6000 6X2 laser cutter was produced in 2014. Technical parameters: – laser source: 6000 W CO2-laser GE Fanuc C6000i-Model C – RF-excitation: 2 MHz – power stability: ± 2% (power monitor) – laser wave length: 10.6 μM – beam mode: Fanuc Low Order Mode – laser shutter: mechanical safety shutter – laser gas composition: CO2 / He / N2 – gas consumption by laser: 20 l / h – cooling water flow rate: 250 l / min – maximum cutting capacity: mild steel 25 mm (during tests the maximum achieved: 30 mm), stainless steel 15 mm, aluminum 12 mm - machine activation time: 22899 h - working time: 10122 h - cutting time: 8429 h – total energy requiremen ...
table length: 6000 mm table width: 4300 mm burner heads: 1 Control: Omnicom 160iLB table height: 700 mm work speed: max. 20.000 mm/min positioning accuracy: 60.000 mm/min weight of the machine ca.: ca. 8 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ...
weight: ca. 300 kg current intensivity: 20 A connection voltage: 230 Volt The data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ...
LINX-SL501-CO2-Laser Engraving machine equipped with fume extraction unit. Machine in perfect working condition. LINX SL 501 is one of the fastest Laser marking machines ever, it makes 90 marks per minute and its developed for the line productions for marking glass, papers, plastic and other non metal parts, As well metal, but just taking coloured skin out.