Pierce Control Automation RUR 2500 P working range: 2.1 m x 6.1 m control: Burny 10 LCD Completely welded portal construction without screwed connections o linear guide in the transverse axis o AC servomotors (12 000 mm/min.) o Digital synchronization on the laeng axis o CNC control system BURNY 10 LCD Plus with touch screen o membrane keyboard o flyingmounted cutting buttons o Automatic initial adjustment of the plasma torch o voltage monitoring of the plasma torch height o 1 torch parking lot outside the cutting area o circuit breaker at the end of all axes 1 x Plasma Kjellberg 160i with manual gas console cutting up to 25mm qualifying cut Optional autogencan Comple ...

The CNC-controlled autogen/plasma cutting machine RUR 2500GP is a completely welded portal construction without screwed connections with linear guides in the transverse axis and digital synchronization in the laeng axis. The HPR260XD plasma system is suitable for use in sheet thicknesses up to 64 mm. The system delivers a high-quality cutting quality, high productivity and reliance with low operating costs. Equipment: ? CNC control system Pierce-19 with 19 touchscreen ? Energy chains with cables and loops ? A motorized plasma torch with automatic initial setting and burner ? Pneumatic anti-collision system ? Plasma cutting unit HPR260XD for cutting structural steel up to a material th ...

The CNC-controlled autogen/plasma cutting machine RUR 2500GP is a completely welded portal construction sizing without screwed connections with linear guides in the transverse axis and digital synchronization in the laeng axis. The HiFocus 280i plasma system is suitable for use in the sheet thickness range of 0.5 - 50 (70) mm. As a soft switch inverter, HiFocus 280i offers a fully electronic power source for the power range up to 280 A. The system provides the best cutting results in the field of laser-like cuts and offers a higher service life of the wear parts. Equipment: ? CNC control system Pierce-19 touchscreen ? Energy chains with cables and loops ? A motorized plasma torch with a ...

 ...

• more information

Pierce control automation RUR 2500 P Work area: 2.1 m x 6.1 m Control: Burny 10 LCD Fully welded Portal construction without bolted connections o LM Guide in the transverse axis o AC servo-motors (12 000 mm / min.) o Digital synchronization on the longitudinal axis o CNC control system BURNY 10 LCD Plus with touch screen o Membrane keyboard o 'Flying' bearing inserts o Automatic initial setting of the plasma torch o Voltage monitoring of plasma torch height o 1 burner parking outside the cutting area o Circuit breaker at the end of all axes 1 x plasma Kjellberg 160i with manual gas console Cut quality cutting up to 25 mm Optional autogen retrofittable Completely Facto ...

; ready to use  ...

• more information

; now ready  ...

• more information

The CNC-controlled plasma cutting machine RUR 2500P is a completely welded portal construction without screwed connections with linear guides in the transverse axis and digital synchronization in the laeng axis. The HiFocus 161 i plasma system from Kjellberg with Contour Cut is suitable for use in the sheet thickness range of 0.5 - 40 (50) mm. As a soft switch inverter, HiFocus 161 i offers a fully electronic power source for the power range up to 160 A. The system is the multi-talent of plasma cutting technology for marking and cutting construction blades, alloyed steels, aluminium and all electrically conductive materials. (see Pdf ) Equipment: ? CNC control system Pierce 19 with touchs ...

Inv. Num. : 6623 Type: RUR Control Automati Producer: Pierce Created: 2006 Parameters: Control system: BURNY 10 LCD Working table length: 6000 mm Working table width: 1600 mm Plasma source: KJELLBERG HiFocus 130 Equipment: Flow Control Fine Focus Labeling device LeibInger JET 2 SE

Machine in good technical condition. The machine was only tested and then never used again. Source: Kjellberg HiFocus 130 Plus. ...

• more information