Schröder MHSU 1500/4,0 - Motorized guillotine shears - Motorized backgauge 750 mm - Hold-down device with hard rubber strip to protect polished sheet metal - Extended extendable support table - All-steel knife 2-flute - Punctures at a distance of 10 mm parallel to the lower knife over the entire course of the table - Selector switch for single and continuous stroke - Rear compartment protection according to CE via 3-beam light barrier and side protective grille -Foot switch - Year of construction 2013 Specification - Effective length: 1530 mm - Capacitance (Rm 400 N/mm²): 4.0 mm - Cutting angle: 2.7° - Stroke rate: 34 rpm - Drive power: 4.0 kW - Nominal power: 5.0 kVA  ...

sheet width: 1530 mm plate thickness: 2,00 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 0,840 t dimensions of the machine ca.: 1,90 x 1,30 x 1,20 m - manual back gauge 500mm - Hold-down device with hard rubber strip - Sheet metal holding device mechanically controlled to the rear including sheet metal slide - Rear area protection via light barrier The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Offer 23476 Specifications: - Max. working width 1020 mm - max. material thickness 3.0 mm - Cutting angle 2.7° - electr. Footswitch - Single stroke – continuous stroke can be pre-selected - Manual backgauge up to 500 mm - Front pull-out sheet metal support - Drive 400 V / 2.5 kW - Space requirement approx. W 1450 x H 1200 x D 1400 mm - Weight approx. 900 kg

sheet width: max. 1500 mm plate thickness: 2,5 mm serial number: 150393 weight: 1300 kg : The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.  ...

• more information

Type HSS 1500 x 6 mm Specifications: Cutting length 1540 mm Sheet thickness in St 6 mm Projection 250 mm Back gauge up to 750 mm  ...

• more information

sheet width: 3020 mm plate thickness: 2,0 mm distance between columns: 3000 mm Control: POS 500 NC stroke: 250 mm : max. 135 ° adjustment: UW 80 mm back stop - adjustable: 1000 mm work height max.: 975 mm total power requirement: 6,0 kW weight of the machine ca.: 3,35 t dimensions of the machine ca.: 4185 x 1650 x 1425 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Pickle injector / steaker, make Schröder, type NT 350, year 2001, with plastic link belt, width 600 mm ...

• more information

This APV Gaulin MC45 homogeniser is a 3-cylinder machine which is designed for 11.600 liter per hour with a maximum pressure of 320 bar. The homogensier is equipped with 2-stages with poppet valve cylinder. Manometer on the stages. Piston diameter: 54 mm. Motor: 100 kW - 380 V - 180 Amp - 50 Hz - 1475 rpm. Oil pumping system inside the machine. Stainless steel cladded., General application:, High pressure homogenizers are used to break up the fat globules contained in the milk under high pressure and thus distribute them evenly in the milk. The fat droplets are crushed by forcing the milk through fine nozzles under high pressure. This process prevents a layer of cream from forming on the mil ...

This APV Schröder Gaulin MC45 homogeniser is a 3-cylinder machine which is designed for 12.000 liter per hour with a maximum pressure of 280 bar. The homogensier is equipped with 2-stages with poppet valve cylinder. Electric pressure transmitter (IFM) on the stages. Overpressure valve on the block. Piston diameter: 60 mm. Motor: 110 kW - 380 V - 201 Amp - 50 Hz - 1482 rpm. Forced cooling on the motor for running at low capacity. Oil pumping system inside the machine. Stainless steel cladded., Additional features:, Excluding:, - Feetplates, General application:, High pressure homogenizers are used to break up the fat globules contained in the milk under high pressure and thus distribute them ...

Schroeder-Combinator / scraped surface heat exchanger technical details: capacity/ flow rate: 20-100 ltr/h against 12 bar engine power: 3,5 KW dimensions: length x with x higth : 170 x 43 x 85 cm weight ca.: 150 kg with this device you can go with: hight viscosity and lumpy food for heating, cooling, mixing and pumping