Table length: 0 mm Table width: 0 mm Longitudinal X: 0 mm Cross Y: 0 mm Vertical Z: 0 mm Positions ATC: 0   Positions APC: 0   GOLDEN SUN - CNC 251 R CNC Dividing unit 4e Axis MACH - ID 6341 Make: GOLDEN SUN Type: CNC 251 R YOP: 1997 incl. tailstock incl. 3 chuck 190 mm centre height 180 mm equiped for MITSUBIHI engines Horizontal    Yes Vertical         Yes Diameter       250 mm Tailstock       Yes Mk indexing        360.000 ° Centre height        180 mm Control system      Mitsubishi servo engines ( MAZAK, FADAL) Dimen ...

As good as new arm down machine with 2 needles, needle spacing 6.4 mm  ...

• more information

White onion peeling machine. The machine consists of three modules: a hopper from which the onion is transferred by a conveyor belt to the sorter. At the sorter there are two workers who sort the onions on both sides, put the usable ones in the holders and throw the damaged or spoiled onions onto the middle conveyor belt ordering them to evaporate. The onions suitable for further processing are conveyed in the incision holder by specially designed knives and then fall onto the rotating rollers. After turning the onion several times, a high-pressure air stream blows away the corresponding layers of the onion down to the white layer. The onion then falls on the sorting table, where it is pi ...

Golden roaster 15kg Automatic manufactured in 2019 with less than 10 tons roasted. Including green coffee lift with scale and destoner All parameters are electronically adjustable on the monitor: - burner power - drum rotation speed - air flow - cooling power - cooling arm rotation speed - green coffee lift airflow - destoner airflow Recipes can be saved and reproduced automatically with the HMI Compatibility with Artisan and Cropster softwares Low consumption premix burner compatible with natural gas and LPG Single phase 220V 50-60Hz electricity Good quality components (Italian motors and gearbox, Beijer HMI and variable frequency drive, Combhex burner, Schnei ...

Qty. 2 Second-hand pickling lines Mfc.: Sundwig Built: 1968 Tank of clean HCl: 50 m³ Tank for dirty HCl: 50 m³ Strip width: 1525 mm Qty. 3 Tanks interconnected one for each bath 310 m³ Qty. 3 Baths HCl 152.5 m Double bath pre-washing water Bath for final water washing Heater Chimney for taking out the acid vapors Acid pumps Auxiliary pumps Leveling machine Mfc.: AEG-EMG Built: Oiling machine Mfc.: Sundwig Built: Coiler Mfc.: Sundwig Built:

Qty. 1 Second-hand cold rolling mill Mfc.: SUNDWIG/MINO Type: 4-HI Built: 1980 Revamped: 2016 Rolled material: Carbon steel SAE1006, S235-S550, C45-C75, IF Strip width max.: 600 mm Thickness: in 6.0 mm out 0.25 – 5.0 mm Speed max.: 500 m/min Coil size: ID 508 mm OD 2000 mm Back-up roll dia.: 590 mm - 625 mm Work roll dia.: 190 mm - 240 mm Motors stands: DC, EAA converters (installed 2004), Rolling force: 500 Tons Coolant Emulsion Filtration by magnetic system Controls PLC system: SIEMENS Scada: Simplicity Thickness control: Entry stand hydraulic equipped with Automatic Gap Control (AGC) Thickness control: Exit stand Utilities: Electrical voltage: ...

The SteriWasher is an innovative new robust, high-performance, validateable part washing system designed for use in pharmaceuticals, biotechnology, food, beverages, healthcare and other critical areas. The washroom is accessible via a robust wing door and is made of 316 stainless steel. It is hygienically constructed. By using a combination of specially developed spraying technologies with variable performance, the washing machine offers energy-rich washing along with an energy-saving rinse, which is selected by a simple recipe selection. Description The SteriWasher ™ parts washers use existing and new technologies to provide an environmentally friendly washing system with low water and ...

This rotary valve was used, was only used for spare parts storage for a foreign project and was therefore never in use. The rotary conveyor thus has no operating hours and is in a new condition. The rotary valve, with square inlet, is suitable for the controlled supply and dosing of powdered and granulated bulk materials from silos, funnels, pneumatic conveyor systems, filter systems and cyclones. Name: Rotary valve Manufacturer: Sunds MDF Type: LAF-200 Year of construction: 2010 Material: Normal steel Drive motor: 11 kW Dimensions: L 3400 x W 2200 x H 2370 mm Empty weight: approx. 4500 kg Speed: 1475 / 22 Condition: Used Tech. Documentation: No Note: Inlet L: 1980 mm x W: ...

Honing diameter maximum: 0 mm Honing diameter minimum: 0 mm Stroke length: 0 mm Number of honing heads: 0   CNC Brand: 0 CNC Model: 0 Technical data Min. diameter: 1.5 mm Max. diameter: 165 mm Max. honing length: 406 mm Spindle speeds: number (steps): 12 from: 200 rpm up to: 2500 rpm Stroke speed: number (steps): 5 from: 80 s/min up to: 310 s/min Voltage 50 Hz 3x: 380 Volt Spindle motor: 0.73 kW Machine´s weight about: 450 kg Overall dimensions machine: Length: 1500 mm Width: 1300 mm Height: 1600 mm Various accessories: Coolant system Automatic workpiece honing unit

Honing diameter maximum: 0 mm Honing diameter minimum: 0 mm Stroke length: 0 mm Number of honing heads: 0   CNC Brand: 0 CNC Model: 0 Technical data Min. diameter: 1.5 mm Max. diameter: 165 mm Max. honing length: 406 mm Spindle speeds: number (steps): 12 from: 200 rpm up to: 2500 rpm Total stroke: 80 - 310 mm Stroke speed: number (steps): 5 from: 80 s/min up to: 310 s/min Voltage 50 Hz 3x: 380 Volt Spindle motor: 0.73 kW Machine´s weight about: 530 kg Overall dimensions machine: Length: 1830 mm Width: 1250 mm Height: 1700 mm Automatic workpiece honing unit