Fabricante:
(Categoria: 106)
: neu : ca. 4 Monate ab Auftragse : Italien : 103500 €: 1956.15 €: 150 to: 500 mm: 1250x1000 mm: 600 mm: 23 mm/s: 4 mm/s: 5.5 kW: 1520 mm: 1270 mm: 2500 mm4-pillar guideram guide roundtable and ram with T-slots2 hand operationSiemens PLCmanometerusers manual Light barrier € on RequestSiemens touchscreen-control, 50 programsstoreable, for programming: • Upstroke and downstroke quota• Break time in the bottom• time of Decompression• setting pressure of work• Pieces counter• prestop in upstroke and downstroke• setting for movement in manual and in automatic• management of alarms and anomalies € on Request Working hour counter € on Request Stroke counter € on Request Decompression valve € on Request Oil cooler with decompreission valve € on Request Pressur switch € on RequestThe data for this ad was created with ModulMWS - the software solution of LogoTech o ...
pressure:035 tthroat:225 mmstroke:8 - 100 mmno. of strokes:110 /mindistance table/ram, max. stroke up, adjustment up:400 mmtable surface area:580 x 460 mmhole in the table:250 x 150 mmtable height over floor:700 mmtable adjustable:230 mmram surface:355 x 120 mmram adjustment:70 mmpower requirement:2,2 kWweight:1,5 tdimensions (WxDxH):1,0 x 1,5 x 2,05 mclutch:rolling key overload protection in ram:mechanical
pressure:160 tthroat:370 mmstroke:150 mmdistance table/ram, max. stroke up, adjustment up:500 mmtable surface area:1000 x 700 mmhole in the table:100 mmtable height over floor:820 mmram surface:600 x 520 mmspeed down:350 mm/sspeed up:350 mm/sworking speed:12 - 36 mm/soil volume:1100 lpower requirement:27,0 kWweight:16,5 tdimensions (WxDxH):1,8 x 2,7 x 3,95 mGerman Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 depth stop:motoric adjustable
material width:450 mmmaterial thickness:0,5 - 1,0 mmno. of straightening rolls:6 straightening roll diameter:53 mmnumber of draw-in rolls:2 diameter of draw-in rolls:96 mmpower requirement:1,0 kWweight:0,65 tdimensions (WxDxH):1,0 x 1,0 x 1,55 m
pressure:100 tthroat:450 mmstroke:170 mmdistance table/ram, max. stroke up, adjustment up:450 mmtable surface area:3220 x 800 mmtable height over floor:850 mmram surface:3220 x 800 mmspeed down:50 mm/sspeed up:150 mm/sworking speed:7 mm/soil volume:600 lpower requirement:20,0 kWweight:16,0 tdimensions (WxDxH):3,7 x 2,5 x 2,6 m
pressure:080 tthroat:360 mmstroke:8 - 112 mmno. of strokes:78 /mindistance table/ram, max. stroke up, adjustment up:467 mmtable surface area:900 x 650 mmhole in the table:250 mmtable height over floor:800 mmpassage to the back:330 mmram surface:650 x 400 mmram adjustment:80 mmpower requirement:11,0 kWdimensions (WxDxH):1,2 x 2,2 x 2,9 mGerman Safety: permitted for manual loading:UVV 11.062 - VBG 7n5.1 overload protection in ram:mechanisch
: neu : ca. 8 Wochen ab Auftragse : Italien : 143100 €: 2704.59 €: 160 to: 6 mm: 1200 mm: 650 mm: 200 mm: 16 - 160 mm: 35 - 55 1/min: 740x420 mm: 8 : 100 mm: 330 mm: 690 mm: 15 kW: 1410 mm: 2220 mm: 3544 mm: 16000 kgtouch screen controlsemi automatic stroke adjustmentdie space adjustment with mechanical display decimal resolutionadjustable motor speedoverload protectorautomatic cams resetdouble bolster plateoil circular lubricationdynamic brakesafety light guard KeyenceAutomation and control of press parameters by PLC, alarms and informations displayd on human machine interface touch screen.Standard monitoring:- press speed view and adjustment- programmable piece counter and maintenance piece counter- die space adjustment with brake motor- Semi automatic or automatic stroke adjustment- die safety control- alarms view- overload protectorThe data for this ad was created with ModulMWS - ...
pressure:160 tstroke:160 fix mmno. of strokes:30 - 120 /mindistance between columns:1190 mmdistance table/ram, max. stroke up, adjustment up:735 mmtable surface area:1200 x 1000 mmhole in the table:500 x 300 mmtable height over floor:900 mmside window:600 mmram surface:1000 x 800 mmram adjustment:125 mmmaterial width of feeder:550 mmmaterial thickness of feeder:0 - 6,0 mmfeed length:350 mmmaterial cross-cut:1100 mm²Feed speed:50 m/minpower requirement:45,0 kWweight:25,0 tdimensions (WxDxH):2,3 x 2,1 x 4,7 minfinitely variable drive:PIV overload protection in ram:hydraulic ram adjustment:motoric ram counterbalance:pneumatic pincer feed:mechanisch, RS 350/550 SL 90
: neu : ca. 10 Wochen ab Auftrags : Türkei : 112800 €: 2131.92 €: 220 to: 3050 mm: Y1 / Y2 / X und R Achse : 265 mm: 2600 mm: 410 mm: 530 mm: hydraulisch : 200 mm/s: 12 mm/s: 180 mm/s: 650 mm: 500 mm/s: 250 mm: 900 mm: 104 mm: 11 kW: 4250 mm: 1770 mm: 2900 mm: 12250 kg1 SERVO MOTOR AND PUMP PER CYLINDERStandard accessories:4 axes (Y1, Y2,X andR)CNC control SKY 22- intuitive touch-screen control (simple drawing of the bending outline with your finger) 21,5 in full HD- with 2D and 3D working screen- direct programming of the bending angle- user friendly programming in dialogue form optionally in 2D or 3D mode- 2D and 3D simulation of the bending sequence- automatic tool selection in 3D mode- automatic calculation of the blank sheet size- bending order calculation- graphic product and tool memory- correction possibility- USB and Ethernet interfaces for import, backup and programm trans ...
pressure:315 tdistance between columns:1620 mmstroke:600 mmdistance table/ram, max. stroke up, adjustment up:1000 mmtable surface area:1600 x 1100 mmpressure of drawing cushion in ram:20 tstroke of drawing cushion in ram:100 mmdrawing cushion area in ram:300 x 300 mmside window:600 x 1100 mmtable height over floor:750 mmram surface:1600 x 1100 mmoil volume:1500 lpower requirement:110,0 kWweight:35,0 tdimensions (WxDxH):4,65 x 2,61 x 5,5 mheight over floor:5,05 mheight beneath floor:0,45 mGerman Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 drawing cushion in ram:hydraulic ram interlocking:pneumatic cutting impact cushioning:hydraulic
pressure:60 tdistance between columns:650 mmstroke:220 mmdistance table/ram, max. stroke up, adjustment up:410 mmtable surface area:600 x 525 mmpressure of drawing cushion in table:5 tstroke of drawing cushion in table:80 mmtable height over floor:900 mmside window:200 mmram surface:560 x 490 mmdimensions (WxDxH):1,9 x 1,3 x 2,7 mGerman Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 light guard:Sick FGS 600 drawing cushion in table:hydraulic foundation pit:not necessary
pressure:60 tdistance between columns:650 mmstroke:220 mmdistance table/ram, max. stroke up, adjustment up:410 mmtable surface area:600 x 525 mmhole in the table:110 mmtable height over floor:900 mmside window:200 mmram surface:560 x 490 mmpower requirement:15,0 kWdimensions (WxDxH):1,9 x 1,3 x 2,7 mfoundation pit:not necessary
: neu : ca. 10 Wochen ab Auftrags : Türkei : 88113 €: 1665.34 €: 220 to: 3050 mm: Y1 / Y2 / X Achse : 265 mm: 2600 mm: 450 mm: 530 mm: hydraulisch : 140 mm/s: 10 mm/s: 140 mm/s: 500 mm/s: 350 mm/s: 250 mm: 900 mm: 104 mm: 250 l: 22 kW: 4250 mm: 1770 mm: 3000 mm: 12600 kgStandard accessories:3 axes (Y1, Y2,X)CNC control DT-15- 2D grafic display 15",- intuitive touch-screen control (simple drawing of the bending outline with your finger)- user friendly programming in dialogue form- automatic calculation of the bending sequence- automatic calculation of the blank sheet size- graphic product and tool memory- correction possibility- USB interfaces for backup and programm transportation- PC software, generating programms on the PC and transfer to the machine by USBservo motorized back gauge on linear guides and ball screwsback gauge finger blocks on double linear guidesCNC crowning ta ...
pressure:250 tdistance between columns:1110 mmstroke:250 mmDistance table/ram, max. stroke up, adjustment up:500 mmTable surface area:1100 x 900 mmTable height above floor:950 mmSide window:690 mmRam surface:1100 x 900 mmOil volume:730 lPower capacity:56,0 kWDimensions (WxDxH):2,3 x 1,55 x 3,96 m
As good as new machine Operating hours in motion: 29.5 Hour meter: 2244 Strokes: 159328 incl. interchangeable decoiling device, strip straightener and Scrap ejection. Mains voltage: 3LNPE/400V/50Hz Control: Beckhoff/PNOZ multi Electrical wiring diagram: E$-M02070 Pre-fuse: 160 A Nominal power: 37 KW Nominal force: 2000 KN Working capacity: 16000 J Stroke rate in continuous stroke: 30-150 min-1 Max. stroke rate in single stroke: 30 min-1 Max. clutch cycles in single stroke: 20 per min Runtime: 0.158 s Min. safety distance: 317 mm Clutch pressure: 5.0 bar System pressure: 6.0 bar Stroke length: 20-220 mm Max. plunger adjustment: 150 mm Usual stopping point of the ram: OU Table dimensions: 1800x1100 Plunger dimension, max. tool dimension (WxD): 1800x1100 mm Max. weight tool top: 1700 kg Mass without additional equipment: 29000 kg Auction-ID: A1-47244-1
pressure:160 tthroat:360 mmstroke:200 mmdistance table/ram, max. stroke up, adjustment up:500 mmtable surface area:920 x 700 mmHole in the table:150 mmtable height over floor:960 mmpassage to the back:590 mmram surface:620 x 560 mmspeed down:390 mm/sspeed up:390 mm/sworking speed:58 mm/spower requirement:30,0 kWweight:16,0 tdimensions (WxDxH):1,6 x 2,5 x 3,6 mGerman Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 depth stop:mechanisch
pressure:2000 tdistance between columns:975 mmstroke:400 mmdistance table/ram, max. stroke up, adjustment up:1000 mmtable surface area:1015 x 1050 mmtable height over floor:800 mmcapacity of ejector in table:6,3 tejector stroke in table:100 mmcapacity of ejector in ram:65 tejector stroke in ram:100 mmram surface:975 x 1050 mmreturn capacity:150 tspeed down:235 mm/sspeed up:250 mm/sworking speed:5 - 20 mm/soil volume:4000 lheight over floor:3,65 mheight beneath floor:3,75 mpower requirement:194,0 kWweight:105,0 tdimensions (WxDxH):5,0 x 6,5 x 7,4 m
pressure:100 tdistance between columns:1000 mmstroke:300 mmdistance table/ram, max. stroke up, adjustment up:650 mmtable surface area:980 x 700 mmpressure of drawing cushion in table:4 x 10 / 1 x 20 tstroke of drawing cushion in table:180 mmtable height over floor:800 mmside window:400 mmram surface:1000 x 700 mmspeed down:500 mm/sspeed up:450 mm/sworking speed:60 mm/spower requirement:40,0 kWdimensions (WxDxH):1,5 x 1,4 x 4,5 mGerman Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 drawing cushion in table:4 x 10 t + 1 x 20 t, getrennt einschaltbar foundation pit:nicht erforderlich
pressure:200 tdistance between columns:970 mmstroke:360 mmDistance table/ram, max. stroke up, adjustment up:630 mmtable surface area:1000 x 800 mmcapacity of ejector:10 tejector stroke in table:160 mmtable height over floor:850 mmside window:400 mmram surface:1000 x 800 mmspeed down:420 mm/sspeed up:410 mm/sworking speed:50 mm/soil volume:1240 lreturn capacity:24 tpower requirement:45,0 + 15,0 kWweight:16,0 tdimensions (WxDxH):2,7 x 2,5 x 4,3 mGerman Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 ram interlocking:mechanisch foundation pit:nicht erforderlich
nominal force:160 tstroke:140 mmno. of strokes:85 /mindistance between columns:400 mmdistance table/ram, max. stroke up, adjustment up:500 mmtable surface area:400 x 450 mmtable height over floor:800 mmAllowed max. force:230 tram surface:400 x 320 mmspindle diameter:125 mmpower requirement:7,35 kWweight:5,0 tdimensions (WxDxH):1,7 x 1,2 x 2,9 m
: gebraucht : 2023 : 8285 : prompt, Zwischenverkauf v : Türkei : 33900 €: 1 : 30 to: 1050 mm: 3 (Y1, Y2, X) : 160 mm: 850 mm: 250 mm: 390 mm: hydraulisch : 10 mm/s: 130 mm/s: 495 mm: 250 mm/s: 835 mm: 104 mm: 75 l: 7.5 kW: 2470 mm: 1250 mm: 2245 mm: 3250 kgdemo machine / mint conditionnet price (price for new machine € 41.200,00)Y1, Y2, X - 3 AxisControl Unit - DT 10 Touch screen 2D graphic (Remote Control)Back gauge: motorized &, linear guide &, ballscrewEuropean clamping systemEuropean clamping system top toolEuropean style bottom tool holderSupport arms with T-SlotSafety side covers (Non CE)World known electrical equipmentsOPTION:DBend, 3D CAD/CAM importing- and simulation program (step, iges and dxf file import) €2.110,-BUYING USED MACHINERY IS A MATTER OF TRUST - OUR TRANSPARENCY PROMISEWe offer you maximum security and complete transparency.• HONEST INSIGHTS: Detaile ...
pressure:063 tthroat:450 mmstroke:8 - 100 mmno. of strokes:65 /mindistance table/ram, max. stroke up, adjustment up:415 mmtable surface area:720 x 800 mmhole in the table:280/250 mmtable height over floor:800 mmpassage to the back:290 mmram surface:450 x 280 mmram adjustment:63 mmpower requirement:7,5 kWweight:4,7 tdimensions (WxDxH):1,3 x 2,0 x 2,65 mclutch:pneumatisch overload protection in ram:mechanisch
Pressure:063 tthroat:400 mmstroke:16 - 90 mmno. of strokes:60 /mindistance table/ram, max. stroke up, adjustment up:350 mmtable surface area:1000 x 750 mmhole in the table:260 x 140 mmtable height over floor:710 mmram surface:600 x 220 mmram adjustment:50 mmweight:4,3 tdimensions (WxDxH):1,1 x 2,6 x 2,4 mGerman Safety: permitted for manual loading:UVV 11.062 - VBG 7n5.1 clutch:pneumatisch overload protection in ram:mechanisch ram counterbalance:pneumatisch
: neu : ca. 10 Wochen ab Auftrags : Türkei : 100920 €: 1907.39 €: 220 to: 4050 mm: Y1 / Y2 / X Achse : 265 mm: 3600 mm: 450 mm: 530 mm: hydraulisch : 160 mm/s: 10 mm/s: 140 mm/s: 500 mm/s: 350 mm/s: 250 mm: 900 mm: 104 mm: 250 l: 22 kW: 5250 mm: 1770 mm: 3000 mm: 14750 kgStandard accessories:3 axes (Y1, Y2,X)CNC control DT-15- 2D grafic display 15",- intuitive touch-screen control (simple drawing of the bending outline with your finger)- user friendly programming in dialogue form- automatic calculation of the bending sequence- automatic calculation of the blank sheet size- graphic product and tool memory- correction possibility- USB interfaces for backup and programm transportation- PC software, generating programms on the PC and transfer to the machine by USBservo motorized back gauge on linear guides and ball screwsback gauge finger blocks on double linear guidesCNC crowning t ...
50 ton gantry press with electronic up and down controls, 230 volt power supply, never used Overall dimensions: 1200 x 500 x 2000 mm Weight: 300 kg Auction-ID: A7-47248-310
pressure:100 tthroat:540 mmstroke:560 mmdistance table/ram, max. stroke up, adjustment up:800 mmtable surface area:1000 x 1000 mmpressure of drawing cushion in table:50 tstroke of drawing cushion in table:200 mmdie cushion area:710 x 650 mmtable height over floor:910 mmram surface:1000 x 1000 mmcapacity of ejector in ram:2 tejector stroke in ram:200 mmreturn capacity:19,5 tspeed down:400 mm/sspeed up:300 mm/sworking speed:57,7 mm/soil volume:650 lpower requirement:37,5 kWweight:15,0 tdimensions (WxDxH):1,5 x 2,5 x 4,45 mGerman Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 drawing cushion / ejector in table:hydraulisch ejector in ram:hydraulisch depth stop:mechanisch
pressure:40 tthroat:360 mmstroke:500 mmdistance table/ram, max. stroke up, adjustment up:660 / 1000 mmtable surface area:630 x 500 mmhole in the table:200 mmtable height over floor:1060 / 720 mmram surface:450 x 360 mmspeed down:60 mm/sspeed up:300 mm/spower requirement:7,5 kWweight:2,75 tdimensions (WxDxH):1,0 x 1,8 x 3,05 madditional plate in table:height approx. 340 mm
: neu : ca. 12 Wochen ab Auftrags : Türkei : 11500 €: 220.8 €: 150 to: fix : 300 mm: 1570 mm: 280x200 mm: 5 mm/s: 10 mm/s: 2500 mm: 1000 mm: 2270 mm: 2100 kgsteel welded framestop at any positionpressure manometersafety valve against overloading2 V-blockstable height adjustabletable up-down movement attachmentcontrol by operating leveraccording to CE regulations user manual in GERMAN and ENGLISHThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure:050 tthroat:255 mmstroke:8 - 120 mmno. of strokes:115 /mindistance table/ram, max. stroke up, adjustment up:380 mmtable surface area:640 x 500 mmhole in the table:250 x 180 mmtable height over floor:710 - 930 mmtable adjustable:220 mmram surface:550 x 170 mmram adjustment:70 mmpower requirement:4,0 kWweight:3,1 tdimensions (WxDxH):1,5 x 1,5 x 2,3 m
99.000 € 
