Fabricante:
(Categoria: 706)
Overview This Krones AirCo is an air conveyor for empty PET bottles, built at the end of 2011. The bottles hang by their neck ring and are driven by air from fan units along the conveyor. The installation runs over a total length of approx. 60 m with seven fan units, curves, a diverter and several declining sections. The conveyor sections hang from stainless steel support stands and run at ceiling level across the hall, so the floor beneath stays free for traffic and other machines. Technical data Manufacturer: Krones Model: AirCo Year of manufacture: 2011 Machine type: air conveyor, neck handling of empty PET bottles Total conveyor length: approx. 60 m Declining sections: 10 sections at 10°, approx. 16.8 m in total Curves: 8 with radius 750 mm - 90° 2 x left, 2 x right; 45° left; 30° left; 15° left; 15° right Fan units: 7, each with filter housing Diverter: 1 Conveyor sections In ...
Overview This GALDI RG50/2 UCS is an automatic form-fill-seal machine for gable-top cartons, built in 2007 in Italy. It erects the cartons from flat blanks, fills and seals them at up to 3,000 cycles per hour, and a cap applicator is included. The machine currently fills liquid egg products and is suitable for milk and other liquid food products. It is still installed and in production. Technical data Manufacturer: GALDI (Italy) Model: RG50/2 UCS Year of manufacture: 2007 Machine type: automatic form-fill-seal machine for gable-top cartons Capacity: up to 3,000 cycles per hour Carton format: 95 x 95 mm cross section Products: liquid egg products; suitable for milk and other liquid foods Installed power: 28 kW Power supply: 380 V / 50 Hz Weight: 5,000 kg Equipment Magazine for flat carton blanks Filling station with sanitary product valves Cap applicator Control panel with QuickPanel View ...
Overview This Scaligera ULISSE 4000 is a sleeve labeling machine for cans, built in 2016 by Scaligera Packaging in Italy. It applies sleeves to sleek and standard cans at up to 4,000 cans per hour and comes with its matching Scaligera steam shrink tunnel from the same year. The line ran carbonated soft drinks in cans and was in production until early September 2023. The machine runs left to right. Sleeves are cut from the reel, opened and placed over the can in the sleever; the steam tunnel then shrinks them tight onto the can body. Technical data Manufacturer: Scaligera Model: ULISSE 4000 Year of manufacture: 2016 Machine type: sleeve labeler with steam shrink tunnel Output: up to 4,000 cans/h Containers: sleek and standard cans Machine direction: left to right Power supply: 400 V, 3-phase, 50 Hz Connected load: 8 kW in total (sleever 2 kW, steam tunnel 6 kW) Max. current: sleever 7 A, ...
Overview Robotic end-of-line palletizing system from a wine bottling plant, consisting of two ABB FlexPalletizer robot cells, an empty-pallet destacker, a Strapex SWR 30 rotating-ring stretch wrapper with its chain conveyor, and the safety fencing of the installation. The robots stack the packed cases onto pallets fed from the destacker; the loaded pallets run on the chain conveyor through the wrapper. The system is still installed in Belgium and can be viewed by appointment. Technical data Robots: 2 x ABB FlexPalletizer, 4-axis, each with its own ABB robot controller Gripper clearance: 1,200 x 240 mm Pallet size handled by the destacker: 1,100 x 1,200 mm Stretch wrapper: Strapex SWR 30, rotating ring, film width 500 mm, clearance diameter 2,000 mm Wrapper pallet loads: 1/4 EURO, 1/2 EURO, EURO and 1,200 x 1,000 mm, load height up to 2,400 mm Film: pre-stretched LLDPE, pre-stretch levels ...
Fabricante: Pack und Palettiertechnik Rudolf Steinle Gersthofen GmbH Tipo: RAPID-EK Ano de Fabricação: 1993 Área base das caixas: 400 mm × 300 mm, adequadas para paletes Euronorm 1200 mm × 800 mm Disponibilidade: a partir de 13.01.2027 Desmantelamento: por comprador Visualização: por marcação Localização: Baviera, Alemanha Pressão do ar: 6 bar Ligação: 220/380 V, 50 Hz Controlo: 24 V CC
O Desempacotador Radenska & Steinle (RS) ARO-P3 é uma máquina industrial de bebidas tipicamente usada em linhas de engarrafamento para desembalar garrafas de caixas ou caixas Condição do Item: Em Funcionamento Disponibilidade: a partir de 13.01.2027 Desmantelamento: por comprador Visualização: por marcação Localização: Baviera, Alemanha Potência: 3 kW Ligação: 380 V, 50 Hz Pressão do ar: 6 bar
A Radenska & Steinle (RS) SPN-2S é uma lavadora profissional de caixas utilizada principalmente na indústria de bebidas para limpar caixas de garrafas retornáveis. Condição do Item: Em Funcionamento Disponibilidade: a partir de 13.01.2027 Desmantelamento: por comprador Visualização. Por acordo Ligação: 380 V, 50 Hz Potência: 8 kW Localização: Baviera, Alemanha
O tipo Schymanski GmbH (MAG): SIRIO 8-24 é uma máquina industrial de lavar garrafas / lavadora de garrafas utilizada principalmente na indústria de bebidas para garrafas retornáveis. Condição do Item: Em Funcionamento Disponibilidade: a partir de 13.01.2027 Desmantelamento: por comprador Visualização: por marcação Localização: Baviera, Alemanha Ligação: 400 V, 50 Hz
A miho DAVID é uma máquina altamente inovadora de Inspetor de Garrafas Vazias. O sistema é utilizado mundialmente na indústria de bebidas e alimentos para inspecionar de forma fluida garrafas reutilizáveis e descartáveis (feitas de vidro ou PET) à procura de defeitos antes de serem reabastecidas. Dados técnicos de desempenho: Alta velocidade de produção: O sistema cria controlo total de até 72.000 garrafas por hora diretamente na operação em linha de montagem. Flexibilidade: O sistema é adequado para uma grande variedade de formas e tamanhos de recipientes. Design Higiénico: O design mecânico está otimizado para os rigorosos requisitos de higiene nas fábricas de engarrafamento e é fácil de limpar. Condição do Item: Em Funcionamento Disponibilidade: a partir de 13.01.2027 Desmantelamento: por comprador Visualização: por marcação Loca ...
A KHS, Krones e Hormes são fabricantes e fornecedores líderes de sistemas e máquinas de engarrafamento para as indústrias de bebidas e alimentos líquidos. Enchimento de garrafas Fabricante: KHS Tipo: VVF O sistema de enchimento de garrafas KHS, tipo VVF (frequentemente referido como Delta VVF ou KHS/SEN VVF) é um sistema clássico de enchimento por contrapressão controlado mecanicamente, especialmente desenvolvido para encher bebidas contendo CO2 em garrafas de vidro ou PET Sistema de tampa de garrafas Fabricante: Hormes Tipo: KK/SV (combinação de rolha coroa / tampa de rosca) A máquina combina duas tecnologias diferentes de tampar num espaço muito pequeno. Pode fechar frascos de forma flexível (maioritariamente garrafas de vidro), seja com rolhas de coroa (para cerveja, limonadas) ou com tampas de rosca (para sumo, vinho, água mineral). Máquina rotativ ...
A Radenska & Steinle (RS) ERO-3T é um embalador industrial de garrafas (embalador/desempacotador) para a indústria de bebidas. A máquina é normalmente utilizada em linhas automáticas de enchimento para garrafas de vidro retornáveis (por exemplo, para cerveja, água mineral ou refrigerantes). Especificações Técnicas e Detalhes Tipo de Máquina: Empacotador de Garrafas (Empacotador de Cabeça de Garra) Cabeças de embalagem: 3 cabeças (daí a designação "3T"), concebidas para pegar e mover paralelamente segmentos de garrafas (por exemplo, grelhas de embalagem para dimensões padrão de caixas, como garrafas 6x4 ou 5x4). Pressão de operação: 6 bar de pressão de ar (controlo pneumático das cabeças das garras). Condição do Item: Em Funcionamento Disponibilidade: a partir de 13.01.2027 Desmantelamento: por comprador Visualização: por marcação Local ...
Overview This Kematec MBK 12 AS, built in 2006, places shrink capsules on wine bottles and shrinks them on in 12 heating stations. It runs at 3,000 - 12,000 bottles per hour and covers bottle heights of 235 - 360 mm and bottle diameters of 50 - 115 mm. The machine is still installed in a wine bottling line and can be inspected on site. Technical data Manufacturer: Kematec Model: MBK 12 AS Year of manufacture: 2006 Machine type: capsule placing and shrinking machine Output: 3,000 - 12,000 bottles/h Capsules: shrink capsules, max. length 80 mm, max. diameter 40 mm Head diameter: 33 mm Heating stations: 12 Capsule magazine: 1,800 capsules Bottle height: 235 - 360 mm Bottle diameter: 50 - 115 mm Working height: 1,100 mm (+/- 50 mm) Direction of travel: left to right Power supply: 400 V, 50 Hz; main drive 0.75 kW Compressed air: 6 - 7 bar, approx. 350 l/min Overall dimensions (L x W x H): 3,7 ...
Overview KHS Innofill NRF filling and closing monoblock for still wine in glass bottles, built in 2007. A 50-valve filler is followed by two 10-head closers: a KHS natural-cork closer with vacuum device and an aluminium roll-on capper by Zalkin, so the machine closes either corks or screw caps. Output 12,000 bottles per hour. The operator panel and software were updated by KHS in 2022. Technical data Manufacturer: KHS Model: Innofill NRF Year of manufacture: 2007 Output: 12,000 bottles/h Filler: 50 filling valves, pitch circle 1,800 mm, filling tube diameter 20 mm Cork closer: KHS, 10 heads, pitch circle 360 mm, electrically heated cork jaws, cork sorter mounted on top Vacuum device with vacuum pump Screw-cap closer: Zalkin aluminium roll-on capper, 10 heads, pitch circle 360 mm, for 31.4 x 24.2 mm aluminium caps Machine pitch 36π, running direction left to right Conveyor: stainless ste ...
Overview This Logopak LOGOMATIC 920 II PF, built in 2007, is a print-and-apply labelling system for pallets. It prints labels by direct thermal or thermal transfer and applies them with a telescopic tamp applicator onto pallets standing still beside the conveyor. The machine is still installed at the end of a wine bottling and palletising line and can be inspected on site. Technical data Manufacturer: Logopak Model: LOGOMATIC 920 II PF Year of manufacture: 2007 Machine type: print-and-apply pallet labeller Output: 4 labels/min Print methods: direct thermal and thermal transfer Label size: 148 x 210 mm (W x H), 3 mm gap Label roll: max. diameter 400 mm, core diameter 76 mm (150 mm) Mounting: vertical, print head at the bottom Control: Logopak POWER LEAP II Interfaces: W&T COM server, RS 232 Power supply: 88 - 240 V AC, 50/60 Hz; 7 A at 115 V, 3.5 A at 230 V Compressed air: required (valve ...
Overview This Kematec T20-3 KMT, built in 2006, dries filled bottles with air knives on their way through an enclosed tunnel before labelling. The bottles run on a 120 mm plastic chain conveyor under inclined air nozzles on both sides. The machine is still installed in a wine bottling line and can be inspected on site. Technical data Manufacturer: Kematec Model: T20-3 KMT Year of manufacture: 2006 Machine type: bottle dryer (air knife tunnel) Conveyor: plastic chain, 120 mm wide Power supply: 400 V, 3 phases, 50 Hz Control voltage: 24 V DC Overall dimensions (L x W x H): 4,500 x 1,350 x 2,600 mm Equipment Drying tunnel with inclined air knife nozzles above and on both sides of the conveyor, fed by vertical air ducts Infeed screw and curved conveyor sections with adjustable guide rails and quick-release clamping levers Siemens SIMATIC touch panel (French, Dutch, German) with output counte ...
Overview This KHS Innopack CA-1, built in 2006, is a carton erector that forms cartons from flat blanks and closes their bottom with hot-melt glue. Blank stacks are fed on a roller conveyor into the magazine; suction grippers pick each blank, erect it, fold the inner bottom flaps, apply glue with a Robatech hot-melt unit, close and press the outer flaps and discharge the carton onto the outfeed roller conveyor. The machine is still installed in a wine bottling and packaging line and can be inspected on site. Technical data Manufacturer: KHS Model: Innopack CA-1 Year of manufacture: 2006 Machine type: carton erector with bottom gluing Glue system: Robatech Concept hot-melt unit with glue nozzles for the bottom flaps Power supply: 400 V, 3 Ph, 50 Hz, 15 A Compressed air: min. 5 bar operating pressure Overall dimensions (L x W x H): 4,550 x 3,450 x 2,720 mm Blank infeed: roller conveyor wit ...
Overview This KHS Innopack SP, built in 2006, is a pick-and-place case packer for bottles. Empty cases run on the case conveyor into the packing zone, where they are stopped and centred; the gripper head picks the bottle formation from the four-lane infeed table and sets it into the cases. The lifting unit travels on a vertical lifting column with counterweight, and the motion is controlled by a KUKA KR C2 controller with KCP teach pendant. Four change-part trolleys with gripper heads for different bottle sizes are included. The packer is still installed in a wine bottling and packaging line and can be inspected on site. Technical data Manufacturer: KHS Model: Innopack SP Year of manufacture: 2006 Machine type: pick-and-place case packer Bottle infeed: 4 lanes, lane width 85 mm Gripper head: 2 x 18 bottle tulips, formation 3 x 6 bottles Case clearance: 175 x 400 mm Power supply packer: 4 ...
Overview This KHS Innopro warmer-cooler is a skid-mounted thermoregulator for wine, built in 2006 by KHS AG in Dortmund, Germany. It brings wine to a set temperature, heating or cooling as required, at up to 9,900 l/h (99 hl/h), designed for an outlet temperature of 18 °C. The core is a three-section Thermowave plate heat exchanger; stainless steel piping, pumps, pneumatically operated valves and instrumentation are mounted on one frame and run from a freestanding KHS stainless steel control cabinet with touch panel. The unit was last used in a wine bottling line. Technical data Manufacturer: KHS AG (Dortmund, Germany) Model: Innopro warmer-cooler Year of manufacture: 2006 (control cabinet 2007) Machine type: thermoregulator for heating or cooling wine, skid-mounted Product: wine Throughput: 9,900 l/h (99 hl/h) Cooling section: wine from 26 °C to 18 °C, cold water 10 °C to 14 °C at ...
Overview This KHS Corvus is a skid-mounted cartridge filtration system (microfiltration), built in 2007 by KHS AG in Dortmund, Germany. Four stainless steel KHS cartridge filter housings for 40-inch cartridges are connected through a pneumatically operated valve manifold and controlled from the skids own stainless steel control cabinet with Siemens PLC. The Corvus range is designed for clarifying filtration, cold sterile filtration and safety filtration of wine, beer and water ahead of the filler. This unit was last used for wine filtration in a bottling line. Technical data Manufacturer: KHS AG (Dortmund, Germany) Model: Corvus Year of manufacture: 2007 (filter housings 2006) Machine type: cartridge filtration system (microfiltration), skid-mounted Filter housings: 2 housings for 19 cartridges of 40 inch, 143 L each; 2 housings for 12 cartridges of 40 inch, 108 L each Housing design rat ...
Flow steam generator with 33 kw/h Capacity: 50 kg/h steamStrom / Volt: 400capacity / hour ca.: 50customs no.: 84022000
New Seegräber GmbH TD9 electric steam generator. Manufacturer: Seegräber GmbH, manufacturer article: 100-0001-0900.9.9 kW, steam output 15 kg/h, maximum steam pressure 2.5 bar.3/N/PE 400 V AC, 50 Hz, CEE 5-pole 16 A, fusing 16 A.Water: GeKa coupling, minimum 2.5 bar, steam outlet NW 25.760 × 345 × 690 mm, approx. 50 kg. Cable approx. 5 m.Standard version, accessories quoted separately. Price and delivery time on request.
Overview Tunnel pasteurizer for the continuous thermal treatment of filled cans and bottles by water spray. The tunnel is built in a U-shape: infeed and outfeed sit on the same end of the machine, so the line returns to the operator side and the footprint stays compact at 6.2 m² of working area. The treatment length is divided into eight zones – three heating zones, one pre-pasteurization zone, one pasteurization zone and three cooling zones – with energy recovery between the zones, so heat taken out of the cooling side is fed back into the heating side. Heating is by steam through a plate heat exchanger mounted on the side of the tunnel. Product enters at +10 °C, is held at +70 °C for 10 minutes in the pasteurization zone and leaves at +37 °C; the full cycle takes 41 minutes. Tunnel body and electrical cabinet are built entirely in AISI 304 stainless steel. Control is by Siemens ...
Overview This KOSME FLEXA 15/720 P3 MM is a rotary labelling machine for pre-cut labels, built in 2013. It carries two wet-glue labelling stations, and a third station adds hot-melt labelling, so one machine covers several labelling tasks. It suits bottlers who work with pre-cut labels and need to switch between different labelling jobs. Bottles enter and leave the labelling carousel via infeed and outfeed starwheels, guided through the carousel by container plates and top centring bells. Brush units and side pressing belts in the outfeed area press the labels on. The machine is fully enclosed by transparent safety doors and panels and is operated from a KOSME touch panel that shows machine and production data. The machine is set up with 4 formats, covering containers from 400 to 450 g/ml, and reaches an output of up to 15,000 bottles per hour. Technical data Manufacturer: KOSME Model: F ...
Overview This KOSME DEPACK B B1F A/67-Rf is a depalletizer for empty containers such as blown bottles, built in 2013. It takes containers delivered in several layers on pallets, removes them layer by layer and transfers them to the downstream machine in the line. It handles containers from 100 to 500 ml at up to 13,000 containers per hour. Full pallets run in on pallet chain conveyors, a gantry-type depalletizing head clears the layers and removes the tier sheets. The machine is enclosed by safety fencing with light curtains and access protection. It is controlled by a Siemens PLC from a separate control cabinet outside the machine and operated from a KOSME touch panel. The machine is format-dependent, with several formats set up. Technical data Manufacturer: KOSME Model: DEPACK B B1F A/67-Rf Year of manufacture: 2013 Machine type: depalletizer for empty containers Output: up to 13,000 c ...
O sistema é utilizado para limpar automaticamente recipientes vazios / recipientes / garrafas antes do processo de enchimento por meio de bicos de ar móveis (filtros puros). O KOSME JET CLEAN G 16/960 1T UP roda os recipientes vazios (aéreo) e remove partículas soltas e impurezas soprando ar filtrado através de bicos móveis. A máquina é usada para remover depósitos soltos dos recipientes antes de entrarem no sistema de enchimento. Capacidade: até 6000 garrafas/h Dimensões: 2500 x 2500 mm Peso da máquina: 1600 kg Ligação: 3x400 V, N, 50 Hz Pressão do ar: 6 bar Pressão da água: 3 bar
O despaletizador separa paletes, recipientes de várias camadas (por exemplo, garrafas sopradas / blocos de garrafa) para um contentor de transporte até à próxima máquina conectada. Capacidade: 13.000 b/h Controlo: Siemens Ligação: 3x400 V, N, 50 Hz Classe de proteção: IP 54 Potência (eletricidade): 27 kW Atual: 49 A Condição: bem mantida, totalmente funcional Disponibilidade: a partir da semana 43 de 2026
Overview H&K (Holstein und Kappert) SVF 120-D rotary can filler, built in 1991, with 120 filling valves for can format 211/202. Rated output is approx. 80,000 cans per hour with standard 330 ml cans. The filler is supplied together with an Angelus 121 L can seamer from 1991, the rinser that ran with it, and the filler platform. It is controlled by a Siemens S7-400 PLC. The machine is already dismantled and ready for loading. Technical data Manufacturer: H&K (Holstein und Kappert) Model: SVF 120-D Year of manufacture: 1991 Machine type: rotary can filler Filling valves: 120 Can format: 211/202 Output: approx. 80,000 cans/h (330 ml) Power supply: 380 V, 50 Hz, 3/N Rated current: 24 A Control voltage: 24 V DC PLC: Siemens S7-400 (CPU 416-2) Scope of delivery Can filler SVF 120-D with 120 filling valves and can lift cylinders Can seamer: Angelus 121 L (202), year 1991 Can rinser operated tog ...
Overview This SMI SK 452 T is a shrink packer for PET bottles, built in 2002 by SMI (Italy). It collates bottles into pack formations, wraps them in shrink film and shrinks the film in the integrated heating tunnel, at an output of up to 30,000 bottles per hour. It handles 0.5 l, 0.75 l, 1.0 l and 1.5 l bottles in 3x2 packs and 0.5 l bottles in 4x3 packs, and has a pass-through mode for running bottles unpacked. The wrapping section is fully enclosed by safety guarding with viewing windows. The machine has been running as the shrink packer of a PET bottling line for water and is still installed and under power, so it can be inspected in production. Technical data Manufacturer: SMI (Italy) Model: SK 452 T Year of manufacture: 2002 Machine type: shrink packer for PET bottles with integrated heating tunnel Output: up to 30,000 bottles/hour Pack formats: 0.5 l (3x2 and 4x3), 0.75 l (3x2), 1. ...
Overview This Twin Pack handle applicator, built in 2002, applies carry handles to PET bottle multipacks. It comes from a mineral water packaging line of the same year with an output of 20,000 - 30,000 bottles per hour depending on format. The machine is still installed and under power and can be inspected on site. Technical data Manufacturer: Twin Pack Year of manufacture: 2002 Machine type: handle applicator for beverage multipacks Line output: 20,000 - 30,000 bottles/h depending on format Line formats: PET bottles 0.25 l, 0.33 l, 0.5 l, 0.75 l, 1.0 l and 1.5 l Control: Siemens text operator panel Equipment Handle application unit with tape reels on a blue steel frame above the pack conveyor Control panel with separate start, stop and reset for the front and rear sections, emergency stop Guarded enclosure with transparent doors Condition Still installed and under power. An inspection o ...
Cylindroconical 965 hl fermentation and storage tank - designed for cooling with ammonia (can also be cooled with glycol), 1 x cone cooling, 3 x frame cooling - Swivel cone - stainless steel - insulated - Stand frame, short - Cleaning air fitting with safety valve - Vacuum valve 5 tanks, also available individually or in partial quantities., Additional title: Outdoor tanks for storing fluids; years of manufacture 1988 - 1991, Capacity: 96450 l, Operating pressure: 2 bar, Length: approx. 12400 mm, Width: approx. 3950 mm, Height: approx. 3950 mm, Weight: 6220 kg, Material: Stainless steel 1.4301, Position: vertical, Base construction: short supporting skirt, Features: 7 tanks; Cooling: 1 x cone cooling jacket, 3 x side wall cooling jacket; swivel cone; insulation; dearation and cleaning combination; safety valve; vacuum valve; temperature measurement
