Fabricante:
(Categoria: 102)
number of spindles:6 spindle passage:32 mmArticle: cam-controlled multi-spindle automatic latheManufacturer: SchutteType: SF32 S DntYob: 2000Eight-spindle automatic lathe with 6 main spindlesmax. nominal diameter: D=32mmpick-up unit,Spindle drum with hirth coupling,Elbaron oil mist filter,sorting chute,Interface for: IEMCA PRA bar loading magazine (optional I: IEMCA PRA52/42/F);coolant tank with hinged chip conveyor;Schimpke KSS active cooler,control: Siemens S7-300 PLC;tooling included in delivery may differ from the imagesPlease, contact us for getting more information and pictures on mail(at)tar-mc.com or www.tar-mc.com
Article: turning latheManufacturer: ErgomatType: TBA-42Yob: 20006The machine was powered exclusively by oil (no emulsion) and was used only for machining brassThe turret is currently not operational. A sensor likely needs to be replacedIncludes IEMCA loading magazine BOSS 545 E, Type 32 NPlease, contact us for getting more information and pictures on mail(at)tar-mc.com or www.tar-mc.com
Lathe with 4 tools only for 3-cylinder crank shaft
weight of the machine ca.:18 tcentre distance:700 mmmax. swing diameter:200 mmLathe with 4 tools only for 3-cylinder crank shaft
weight of the machine ca.:18 tcentre distance:700 mmmax. swing diameter:200 mmLathe with 4 tools only for 3-cylinder crank shaft
max. workpiece diameter:29 mmmin. workpiece diameter:26 mmworkpiece length:66 mmthe system was originally delivered for the following workpiece sizes: diameter 26mm - 29mm length 65mm - 66mmChanging parts in the clamping device, handling, etc. would probably result in diameters of up to approx. Ø50mmTotal length will probably be almost 400 mm possible with a few conversions.Also dependent on tool lengths, machining lengths on the component, etc.Workpiece: Piston pin Drawing number: WHT 000 718, WHT 000 718 A Workpiece dimensions (Ø, WxH): Ø26 x 66; Ø29 x 65 Length: 66 or 65 mm Material: 17Cr3Quantity: xxx parts / year Cycle time: 5 sec. However, workpiece lengths up to 600mm are manageable. The machining diameter can be adjusted if the appropriate tools are available. The clamping station can currently only accommodate this product. However, this can be adapted by changing the clampi ...
turning diameter:250 mmswing diameter:250 mmturning height:200 mmtotal power requirement:37,7 kWchuck diameter:315 mmspindle speed max.:5500 1/mintravel -x axis:625 mmtravel -y axis:+100/-80 mmtravel -z axis:250 mmworktool system:VDI 30+40 weight of the machine ca.:8 tThe synchronous spindle is powered with 37.7 kW of power, a torque of 300 Nm and a maximum speed of 5,500 rpm.Typical components are ball cages, ball hubs, gear wheels, sliding sleeves,pump wheels, flanges, synchronizer rings, bearing rings and pivot pins.The machine bed is made of Hydropol, a mixture of special concrete and steel, which ensures the greatest smoothness and precision even with larger components and powerful machining.
number of spindles:6 spindle passage:18 mmturning length:63/50 mmweight of the machine ca.:8,6 tspindle drive motor:11 kW
turning diameter over bed: 330 mmturning diameter over slide rest: 165 mmturning length: 800 mmtotal power requirement: 3 kWweight of the machine ca.: 0,75 tdimensions of the machine ca.: 2 x 1 x 1,5 mNo. 1009Lathe WEILER LZ-300Speed range 24-2800 1/min.Feed rates 0.013-1.27 mm/minSpace requirement approx. 19 0x 700 mm,Weight approx. 700 kg.The e-lead spindle is removed from the machine3-jaw chuck, collet quick-clamping device with various collets, 1 tool cabinet with various accessoriestool cabinet with various accessories.Working area: 165 x 600Drive: 3 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
turning diameter over bed: 570 mmturning diameter over slide rest: 365 mmturning length: 3000 mmtotal power requirement: kWweight of the machine ca.: 5 tdimensions of the machine ca.: 5,5 x 1,44 x 1,38 mWell-maintained lathe from the maintenance department.Working range:Swing diameter over bed 570 mmSwing diameter over cross slide 365 mmSwing diameter in bed recess 600 mmLength of bed recess in front of main spindle 160 mmTurning length 3000 mmCenter height over flat surface 280 mmBed width 360 mmMaximum workpiece weight without steady rest 500 kgMaximum workpiece weight with steady rest 630 kgMain spindle speeds 11.2 - 2240 rpmDrive power 15 kWFeeds60 longitudinal feeds/revolution 0.063 - 56 mm60 cross feeds/revolution 0.0315 - 28 mmTapping60 thread pitches 0.25 - 224 mm60 thread counts 112 - 0.125 TPITravelsCross slide 345 mmTop slide 125 mmTailstock quill 190 mmMain spindleSpindle he ...
turning diameter:200 mmturning height:120 mmweight of the machine ca.:18 tAvailable from 01.08.2024
: neu : ca. 4 Monate ab Auftragse : Bulgarien : 44400 €: 848.04 €: 500 mm: 1500 mm: 250 mm: 80 mm: 300 mm: 400 mm: 8 : 80 MK: 21 : 20-2000 1/min: 120 : 0.04 - 12 mm/U: 0.02 - 6 mm/U: 64 : 0.5 - 120 mm: 60 - 1/4 Gänge/: 0.125 - 30 : 240 - 1 : 315 mm: 130 mm: 90 mm: 5 MK: 230 mm: 7,5 kW: 3100 mm: 1250 mm: 1400 mm: 2820 kgdriven by manual transmission3-axes digital readoutquick change toolpostAmestra with 4 holders (3 square, 1 round)3-jaw chuck Bison 3204/DIN6350, Ø 250 mmspindle dead centerlongitudinal stop for 1 positioncoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platesquick release tailstocklow voltage machine lampoperating manualmachine according to ",CE",FURTHER TURNING LENGTHS: turning length1.000 mm € 43 420,00 turning length2.000 mm € 46 190,00 turning length3.000 mm € ...
turning diameter:1000 mmswing diameter:1000 mmMachine type: Vertical latheManufacturer: HessappType: DV 62Serial no.: 14.2308Working range of the spindleLargest diameter 1000 mmLargest swing diameter 1000 mmCross slide travelStroke of the vertical slide 900 mmStroke of the horizontal slide 1810 mmTotal travel 2315 mmTurning spindleSpindle head with centering cone according to DIN 55021 A15Spindle diameter in the front bearing 203 mmMain driveVia a controlled asynchronous motor and gear transmissionwith range switching.Spindle speedsSpeed range I: 5 - 350 rpm.Speed range II: 30 - 1000 rpm.Travel speedX/Z axis: 10 m/min.W1 axis: 8 rpmNo C-Axis
: neu : ca. 4 Monate ab Auftragse : Bulgarien : 36070 €: 688.94 €: 400 mm: 1000 mm: 200 mm: 52 mm: 235 mm: 320 mm: 6 : 6 MK: 12 : 50-2.240 1/min: 80 : 0.015 - 0.6 mm/U: 0.0075 - 0.3 mm/U: 40 : 0.25 - 7.5 mm: 120 - 4 Gänge/: 0.0625 - 1.875 : 480 - 16 : 235 mm: 110 mm: 50 mm: 4 MK: 100 mm: 4 kW: 2750 mm: 1100 mm: 1600 mm: 1540 kgdriven by manual transmission3-axes digital readout Fagor 40iquick change toolpostMultisuissewith4 holders (3 square, 1 round)3-jaw chuck Bison 3204/DIN6350, Ø 200 mmspindle noseNr. 6 DIN 55027four way rapid traverse devicespindle dead centercoolant equipment1 pce. flange plate for lathe chuckØ 200 mm1 adapter sleevefull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platesquick release tailstocklow voltage machine lampoperating manualmachine according to ",CE",FURTHER TURNING LENGT ...
faceplate diameter:800 mmpower requirement:110 kWweight of the machine ca.:37.000 / total 52.000 ttransport measurements machine:5,07 x 2,98 x 3,90 mclamping diameter:800 mm:Ø 800 x 720 mmTool bore:Capto C6 tools in tool magazin:2 x 80 With C-Axis
faceplate diameter:1600 mmpower requirement:80 kWweight of the machine ca.:25 tdimensions of the machine ca.:4,4 x 4,62 mmax. workpiece diameter:2000 mmmax. diameter of face turning:1800 mmtool taper:ISO50 The machine has been regularly serviced and is in good technical condition. With C-Axis
: gebraucht : 2011 : 010192 : prompt, Zwischenverkauf v : Deutschland : 26700 €: 1 : 320 mm: 650 mm: 160 mm: 40 mm: 192 mm: 205 mm: 5 : 5 MK: 16 : 48 - 2500 1/min: 24 : 0.02 - 0.63 mm/U: 0.006 - 0.2 mm/U: 0.25 - 8 mm: 80 - 2 Gänge/: 0.2 - 4 : 200 - 5 : 150 mm: 100 mm: 40 mm: 3 MK: 85 mm: 2,4 / 3 kW: 1582 mm: 715 mm: 1245 mm: 720 kgHeidenhain 3-axis digital readoutNEW Röhm 3-jaw chuck, 160 mm diameter, with internal and external jawsQuick-change tool post with one rectangular insert and one round insertQuick-release collet chuck with collets from 3 to 29 mm diameter (in 1 mm increments)Live centreDrill chuckChuck guardLead and feed screw guardMotor brakeCoolant systemMounting feetOperating instructions in German with CE declaration of conformityThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
turning diameter:270 -300 mmturning length:710 mmtotal power requirement:43 kWweight of the machine ca.:8,5 tdimensions of the machine ca.:3,16 x 2,15 x 2,15 mThe machine does not include a chuck or tools ? the machine was originally purchased without these accessories. The G300 has X, Z, Y, C, SP, and driven tools. A bar feeder can be used, but the machine does not have one.
turning diameter:250 mmswing diameter:260 mmAvailable from October 10, 2025 The system consists of two individual systems that are linked together.No driven tools!
turning diameter:220 mmturning length:310 mmtotal power requirement:17 kWweight of the machine ca.:3,3 tdimensions of the machine ca.:2,25 x 1,63 x 1940 mgreates pass round over bed:430 mmbore diameter:45 mmcentre distance:687 mmslide travel radial ( X-axis ):160 mmslide travel axial ( Z-axis ):310 mmspindle turning speed range:0-6.300 U/min
turning diameter:220 mmturning length:700 / 665 mmtotal power requirement:17 kWweight of the machine ca.:2,6 tdimensions of the machine ca.:2,63 x 1,98 x 1,94 mgreates pass round over bed:430 mmPart length max.:510 slide travel radial ( X-axis ):160 mmbore diameter:45 mm
turning diameter:360 mmturning length:520 mmtotal power requirement:20 kWweight of the machine ca.:3,8 tdimensions of the machine ca.:3 x 2 x 2 m
turning diameter:360 mmturning length:520 mmtotal power requirement:20 kWweight of the machine ca.:3,8 tdimensions of the machine ca.:3 x 2 x 2 m
turning diameter:490 mmturning length:2000 mmtotal power requirement:15/20 kWweight of the machine ca.:3,6 tdimensions of the machine ca.:2,8 x1,85 x 1,9 mIn like new conditionHeidenhain cycle controlTorsion-resistant bed, made of high-quality cast iron with hardened, precision-ground guideways and a glass scale on the X-axisSafety clutch on the Z and X axesSealing air with carbon filter in direct position measuring systemHigh accuracy and rigidity of the lathe spindle thanks to precision spindle bearings, spindle bore Ø 93 mm standard, optional Ø up to 130 mmSolid tailstock, quill Ø 90 mm with internal taper MK5Large overhang above the facing slide for easy accessibility during shaft machining.The machine has Teach-in CNC Programms.Control: MC420.Tool holder: SAUTER.Texte, Bilder, Grafiken, Layout, Strukturen und Algorithmen etc. unterliegen weltweitem Urheberrecht.Unerlaubte Verwend ...
turning diameter:270 mmturning length:710 mmweight of the machine ca.:6,5 tmax. swing diameter:590 mmwith automatic loading and unloading system G300 with "spindle bore clamping capacity 90mm" in tailstock versionThe machine has no driven tools. The information in the circuit diagram refers to the rotary drive for indexing the turret, not to driven tools.
turning diameter:270 mmturning length:710 mmweight of the machine ca.:6,5 tmax. swing diameter:590 mmwith automatic loading and unloading system G300 with "spindle bore clamping capacity 90mm" in tailstock versionChip conveyor, belt filter press, hydraulic unit, as well as infeed and outfeed chain conveyor EWAP, with 33 pallets. The machine has no driven tools. The information in the circuit diagram refers to the rotary drive for indexing the turret, not to driven tools.
turning diameter:270 mmturning length:710 mmweight of the machine ca.:6,5 tmax. swing diameter:590 mmwith automatic loading and unloading system, chip conveyorG300 with "spindle bore clamping capacity 90mm" in tailstock versionThe machine has no driven tools. The information in the circuit diagram refers to the rotary drive for indexing the turret, not to driven tools.
: neu : Bulgarien : 24940 €: 478.85 €: 325 mm: 750 mm: 165 mm: 32 mm: 190 mm: 200 mm: 5 : 4,5 MK: 2 : 85-405, 470-2200 U/Min: 48 : 0.006 - 1.77 mm/U: 0.003 - 0.885 mm/U: 0.1 - 28 mm: 0.1 - 1.75 : 70 - 4 : 150 mm: 95 mm: 40 mm: 3 MK: 100 mm: 2.2 kW: 2150 mm: 950 mm: 1350 mm: 770 kgdriven by variable speed control (2 steps)3-axes digital readout FAGOR with CSS (constant surface speed)quick change toolpostAmestra with 4 holders (3 square, 1 round)3-jaw chuck Bison 3204/DIN6350, Ø 160 mmspindle dead centercoolant equipmentfull length rear splash guardleadscrew and shaft protectionsafety guard for the chucktoolholder guardlevelling bolts and platesquick release tailstocklow voltage machine lampoperating manualmachine according to ",CE",FURTHER TURNING LENGTHS: turning length1.000 mm € 25.360,-The data for this ad was created with ModulMWS - the software solution of LogoTech oHG ...
turning diameter:250 mmswing diameter:260 mmAvailable from October 10, 2025 The system consists of two individual systems that are linked together.No driven tools!
