Fabricante:
(Categoria: 107)
Coil weight: 500 kg Material width: 41 mm Coil exterior diameter: 1.000 mm Expansion range: 250 - 500 mm Speed: 20 m / min Required power: 0,5 kW Dimensions L x W x H: 1.000 x 850 x 1.700 mm Weight of machine approx.: 200 kg
contact roller: 70 x 50 abrasive belt size: 2000 x 12/50 power capacity: 2,2 kWOverall size: ca. 400 x 1100 x 1250 mmdeburring machine / free belt frinding machineabrasive belt with widt from 12-50 mm with vertical working positionhead inclination up to 45° both wayseasy bending of the belt allows to follow the shapecutting speed 24m / secbig tabel surface with ball rollingwith self filtering dust extractor system, filtering bag in retardant polyester material for retaining finest dust. Impeller with open blades to prevent clogging. air consumption 700 m³/hcomes with a huge bunch of belts!The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bending speed: 2.1 m/minBending capacity - square: 30x30 mmbending capacity - flat iron: 80x15 mmBending capacity - flat iron on edge: 50x10 mmtube diameter: 1 oder 60x2 mmShaft diameter - upper: 35 mmShaft diameter - lower: 30 mmtotal power requirement: 0,75 kwrange L-W-H: 650 x 500 x 1300 mmweight: 170 kgStandard features:- hardened special steel shafts- a set of hardened rollers- Bottom rollers are driven- lateral straightening rollers- Foot pedal- horizontal and vertical workingThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
serial number: 4412956673057 : 95 to. ca. engine output: 7,5 kWweight of the machine ca.: ca 5 tdimensions of the machine ca.: 2,2 × 1,0 × 2,3 m Technical specifications (from the label)Angle steel (L-profile):150 × 15 mm at 90°100 × 14 mm at 45°Flat steel:up to approx. 150 × 16 mmlarger cross-sections up to 340 × 16 mm (depending on function)Beam profiles:U-profiles (UPN): 220I-sections (IPN)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2040 mmplate thickness: 4,0 mmdistance between columns: 2100 mmroll diameter: 150 mmtotal power requirement: 7,0 KWweight of the machine ca.: 2,2 tdimensions of the machine ca.: 2,95 x 1,0 x 1,75 mmSheet metal bending machine with 3 rollers- 2 driven rollers- Rear roller electrically adjustable- Conical bending- Foot switch- Emergency stop deviceThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1020 mmplate thickness: 2.5 mm: 45.0 mmbending angle max.: 0 - 135 °weight of the machine ca.: 285 kgrange L-W-H: 1175 x 850 x 1175 mmDescription:Swivel bending machine with patented hydraulic auxiliary cylinder andRemote control. The machine is both manual (for thinner sheets) andmotorized (for thick sheets) operated. The motorized function is overa remote control operated with an emergency stop.Version S - with segmented upper beam for boxes and special profiles- Max. Bending angle 135 °- Max. Opening upper beam 45 mm- The HS Ergo is a further developed machine that uses a patient hydraulic auxiliary cylinder is supported- The machine is both manual (for thinner sheets) and motorized (for thick sheets) operated.- the motorized function is operated via a remote control with emergency stop The data for this ad was created with ModulMWS - the software solution of LogoTech ...
plate thickness: 4,0 mmroll diameter: ca. 120 mmthroat: 450 mmtotal power requirement: kWweight of the machine ca.: 0,48 tdimensions of the machine ca.: 1,3 x 0,8 x 1,8 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1250 mmplate thickness: 1,5 mmdistance between columns: 1300 mmdaylight opening: 80 mm: 155 °total power requirement: Handbetrieben weight of the machine ca.: 0,18 tdimensions of the machine ca.: 1,4 x 0,8 x 1,3 mSegment-bending machineSegment widths:2x50mm,1x70mm,2x75mm, 2x100mm,4x150mm, 1x170m.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 70 -800 kNchamfer lenght: 2505 mmdistance between columns: 2125 mmControl: OP 2000 controlled axis: 7 throat: 420 mmstroke: 200 mmdayligth: 470 mmNumber of working hours: htable width: 60 mmtable height: 960 mmajustment speed: 100 mm/secworking feed: 10 mm/secreturn speed: 100 mm/secweight of the machine ca.: 6,3 tPatented Amada technology ensures absolutely correct bending results withoutbombing deviceThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
tube diameter: 6 - 42 mmwall strength: 3 mmbending radius min.: 180 mmbending radius max.: 5 mmtotal power requirement: 1,5 kWweight of the machine ca.: 0,8 tdimensions of the machine ca.: mEquipment:Saw unitNotching unitDeburring unit for internal and external edgesFlaring unit / flaring function (necking / expanding)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2500 mmplate thickness: 3,0 mmdistance between columns: 2550 mmtrue cutting angle adjustable: - back stop - adjustable: max. 510 mmcutting gap adjustment: - mmtotal power requirement: kWweight of the machine ca.: 1,8 tdimensions: 3,3 x 1,4 x 1,8 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1000 mmplate thickness: 3,0 mmdistance between columns: 1050 mmdiameter of upper rolls: 90 mmtotal power requirement: 1,1 KWweight of the machine ca.: 0,47 tdimensions of the machine ca.: 1,7 x 0,8 x 1,35 mmSheet metal bending machine with custom dimensions:- Capacity 1050 x 3.0 mm- Digital display- Hardened rollers- Conical bending- Swiveling top roller- Brake motor- Safety device: Emergency stop cord- Documentation in English- 400VThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cutting dimensions max.: 600 x 1000 mmplate thickness: max. 3 mmcutting angle: 1,5 °side stop electrical adjustable: 0 - 1010 mmrear stop electrical adjustable: 0 - 610 mmno. of strokes: 60 Hub/mintotal power requirement: 14 kWweight of the machine ca.: 8,7 tdimensions of machine L x W x H: 2,5 x 2,18 x 2,3 mAccessories: sheet metal stacking device on railsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1350 mmplate thickness: 4.0 mmthickness at Niro-steel: 2.0 mmno. of strokes: max. 35 Hub/mincutting angle: 2.0 Gradtable height: 945 mmdistance between columns: 1361 mmControl: CIDAN / SIEMENS engine output: 5.5 kWweight of the machine ca.: 1400 kgrange L-W-H: 2200 x 2000 x 1550 mmFeatures:- robust / motorized swing cut guillotine shears- unbreakable and torsion-free welded steel construction- compact and clear machine construction- NC electro-motorized backgauge, with digital display Target / actual value stop value input stepless adjustment over the entire travel range- 1x hold-down bar- 1x material side stop- recessed grips in the front support table- Manual cutting gap adjustment from the front- Rear sheet holding device for thin sheets- 1x freely movable foot switch- Operating instructions (PDF)The data for this ad was created with ModulMWS - the software solution of Lo ...
sheet width: 4000 mmplate thickness: 30 / 35 mmpre-bending: 30 mmdiameter of upper rolls: 570 mmside roll diameter: 450 mmdiameter of lower rolls: 540 mmbending speed: 4 m/minmin. bending diameter: 650 mmtotal power requirement: 60 kWweight of the machine ca.: 52 todimensions of the machine ca.: - mThe machine was overhauled in 2022Equipment:- Hydraulic 4-roller round bending machine- Roll material: 61 MnCrMo 43- Driven rolls: 2 Top-and bottom roll-- Drive: over 2 hydro motors direct flanged-- Adjustment speed bottom roll: 0-200 mm/min-- Adjustment speed side rolls: 0-700 mm/min- Speed compensation between top-and bottom roll: automatic- Operation of the tilting bearing: hydraulic- Tilting of the top roll: hydraulic- Bearing block: hydraulic- Indicator device of roll position: digitalThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2050 mmplate thickness: 4,5 mmpre-bending: 4,0 mmmin. dia.: 210 mmroll diameter: 140 mmweight of the machine ca.: 1530 kgdimensions of the machine ca.: 3220x1200x900 mmStandard features:- Central rollers via electric motor, planetary reduction gear andGear drive driven- Swivel top roller- Main engine with brake device- Conical bending device- Mobile controller and foot pedal- CE mark / Declaration of ConformityAdditional equipment:- motorized rear roller adjustment- Digital display for back roller- induction hardened rollsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
material width: 0400 mmcoil weight: 1,50 tmaterial thickness: mmnomb. of straightening rolls: 9 diam. of the rolls ca.: 30 mmrange of expansion ca.: 460 - 530 mmcoil outside - diam. ca.: 1500 mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: : : total power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3050 mmplate thickness: 6 mmdistance between columns: 3460 mmtable height: 800 mm0: 220 barcutting angle adjustment: 0,5x3 °down holder: 18 back stop - adjustable: 750 mmfront stop - adjustable: 1000 mmmain drive: 7,5 kWoil volume: 300 ltotal power requirement: 7,5 kWweight of the machine ca.: 4,5 tdimensions of the machine ca.: 3,7x2,0x1,8 mcutting angle adjustment manuallyblade gap adjustment manuallyangle stopThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2500 mmplate thickness: 3 mmdistance between columns: 2540 mmback stop - adjustable: 550 mmtotal power requirement: 5 kWweight of the machine ca.: 2,7 tdimensions of the machine ca.: 3,2 x 2,5x 1,9 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
plate thickness: 4 mmblade length: 220 mmpressure: 0 tweight of the machine ca.: 1,5 tdimensions of the machine ca.: 1,6 x 1,7 x 1,6 mtotal power requirement: 2,5 kWCombined notching machine with a fixed 90° angle and an adjustablerectangular notching unit variable up to 200mm length x fixed 100mm width.There are 2 manually adjustable stops with a digital display.Axle length X900mm / Y300mmThere is no stamp holder / punch / hold-down device for this.These parts can be purchased from Boschert.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
plate thickness: 3-4 mmpressure: 0 tCutting length: 220 mmtable height: 900 mmquantity of oil: 35 lTable dimensions: 950 x 790 mmtotal power requirement: 4 kWweight of the machine ca.: 0,95 tdimensions of the machine ca.: 1,0 x 0,86 x 1,2 mFoot switch angle adjustment 30°-140° automatic cutting gap adjustmentThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Decoiler Decoiler with arm: 1,5 ton Material width: 350 mm Coil exterior diameter: 1.200 mm Expansion range: 370 - 430 mm Speed: 0 - 20 m / min Leveller / Straightener Material width : 250 mm Number of levelling rolls: 9 pcs. Diameter of the levelling rolls: 30 mm Material thickness: 0,5 - 6 mm Cross section: 1.200 mm Feeding speed: 20 m / min Required power: 18 kW
engraving field: 120 x 120 mmtable-size: 250 x 250 mmworkpiece weight: max 50 kgControl: Fobagraf machine weight ab.: 1000 kgmachine frame made of welded steel constructionCross slide, hard stone design, table top with steel stop ironHeight-adjustable laser headQuality-switched ND: YAG laser head, lamp-pumped, 100 WDeflection unit mounted on the laser head (with standard lens)Z-axis with gearbox and servo driveServo axis control with X-, Y-, and Z-axesWater-cooledControl: Fobagraf user software packageOperating system: Windows 2000operating hours: 17.388 hmanual includedThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3240 mmplate thickness: 2,00 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: 3,00 tdimensions of the machine ca.: mManual and automatic bending operation possibleBending angle adjustable via potentiometerUpper beam stroke height and material thickness selectable via DIP switchesBending rail and machine in excellent conditionThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
round bar steel: 34 mmsquare edge steel: 30 x 30 mmL-beam: 100 x 10 mmflat steel: 100 x 14...160 x 11 mmblade length: 175 mmT-beam: 100 x 10 mmnotching: l + T material: 10 mmhole punhing press: pressure: 45 tthroat: 305 mmtotal power requirement: 3 kWweight of the machine ca.: 1,2 tdimensions of the machine ca.: 1,4 x 0,8 x 1,5 m 5-fold combinated profile steel shear incl. flat steel shear profile steel shear bar steel shear notcher hole punch 2 foot switches contact limit stop various punching saddles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2040 mmplate thickness: 3,00 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: 2,30 tdimensions of the machine ca.: mManual and automatic bending operation possibleBending angle adjustable via potentiometerUpper jaw stroke height and material thickness selectable via DIP switchesManual backgauge with spring fingersThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table width: 6000 mmtable length: 2000 mmburner heads: 1 Equipment:- Plasma source Kjellberg Hi Focus 161i- suction unit- CompressorTechnical dataKjellberg Hi Focus 161i plasma cutter:Cutting current at 100 % ED 10 - 160 AMarking current 5 - 25 ACutting range 0.5 - 50 mmPiercing up to 30 mmDimensions (L x W x H) 985 x 570 x 1140 mmMass 206 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
