Fabricante:
(Categoria: 107)
Dimensions (L/W/H): 1500x1220x1300 mmWeight: 1050 kgTotal power requirement: 16,1 kwThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 2985x2160x2000 mmWeight: 2000 kgTotal power requirement: 30 kwThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3100 mmplate thickness: 4.0 mmthickness at Niro-steel: 2.5 mmcutting angle adjustment: 1.0 °back stop - adjustable: 10 - 1000 mmadjustment speed: 180 mm/sdown holder: 21 Stückstrokes per minute: 18 - 31 oil volume: 160 LControl: ELGO P8511 column arm: 200 mmdistance between columns: 3050 mm0: max. 300 barvoltage: 400 Vmain drive: 9.0 kWweight of the machine ca.: 4800 kg.dimensions of the machine ca.: 3660 x 2070 x 2140 mm from a maintenance workshopEquipment:- electro-hydraulic sheet metal shear swing cut- machine frame = all-steel welded construction- ELGO NC control model P8511, control panel at the front left for positioning the electro-motoric rear stop target/actual position value input possible adjustment by three-phase motor via toothed belt- support table with ball rollers there are recessed grips between the table plates- front finger guard- hydraulically acting s ...
sheet width: 3100 mmplate thickness: 2 mmrear stop: 1000 mmcutting angle: 1°06 °no. of strokes: 45 Hub/mintotal power requirement: 3,0 kWdimensions of the machine ca.: 3600 x 2200 x 1600 mmweight: 4500 kgEquipment:- Electric motorized backgauge- With digital ELGO position display- Manual cutting gap adjustment- 1x side stop with mm scale- 2x support arms- 1x freely movable double foot switch- Front finger guardSpecial accessories included:- Pneumatic sheet metal holding device for thin sheet metal cutsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2540 mmplate thickness: 6 mmrear stop: 900 mmdown holder: 14 Stkno. of strokes: 20 Hub/mintotal power requirement: 10 kWdimensions of the machine ca.: 3100 x 2200 x 2600 mmweight: 5000 kgFeatures:- Central lubrication- Electric rear stop- 1x side stop 2350 mm- 2x front support arms with stop 1700 mm- Front finger guard- Spare blade (used)- Foot switchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
tube diameter: 4 - 28 mm: 3000 mmbending radius max.: 90 °connected load frequency: 400 Vtotal power requirement: 1,5 kWweight of the machine ca.: 0,75 tdimensions of the machine ca.: 3,7 x 1,2 x 1,5 mElectro-hydraulic mandrel tube bending machine with- Bending mandrels for 18mm tube- Tools for: 8mm, 10mm, 12mm, and 18mm- PC interface- Laptop- DocumentationSee images for further accessoriesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
plate width: 125 mmplate thickness: 2 mmstraightening feed: 5-30 m/mintotal power requirement: 1,5 kWweight of the machine ca.: 460 kgdimensions of the machine ca.: m- Belt infeed height: 1,250 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
tube diameter: 273 mmwall strength: 15,1 mmbending radius min.: 150 mmbending radius max.: 1250 mmtotal power requirement: 30 kWweight of the machine ca.: 3,5 tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
working length: 2050 mm: 2.0 mmmax. wire thickness: 3.0 mmUnderfloor: 110 mmmotor strength: 165 mmmotor strength: 22 kWbending speed: 5.2 mm/minlength: 3150 mmheight: 1150 mmwidth: 850 mmAccessories / equipment:- Conical bending device- induction hardened rolls- digital display for side rollers- Machine made of steel construction- Separate control panel- two speeds- all rollers on ball bearings- Folding and support bearing from the top roller is actuated from the control panel.When the folding bearing is opened, the roller moves automatically upwards.- Conical adjustment of the rollers via control panel- Central rollers are via hydraulic motor and rotary reduction geardriven. (Top and bottom rollers)- CalibrationThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 4040 mmplate thickness: 4,00 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: 7,50 tdimensions of the machine ca.: mMotorized adjustable backgauge with digital display up to 1000 mmPneumatic sheet metal supportSide fence and table extensionsCut length limiterCut edge lightingThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3100 mmplate thickness: 6,00 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mMotorized backgauge with digital displayManual kerf adjustmentVariable cutting lengthCutting edge illuminationNew bladesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3100 mmplate thickness: 10,00 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: 10,00 tdimensions of the machine ca.: mMotorized backgauge up to 1000 mm with digital displaySide fence and table extensionsCut length limiterCut edge lightingNote: Backgauge is slightly inaccurate (+/- 1 mm)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2050 mmplate thickness: 2 mmstrokes per minute until: 38 cutting angle: 1,75 °table height over floor: 870 mmtotal power requirement: 3 kWweight of the machine ca.: 1520 kgrange L-W-H: 2,2 x 0,6 x 1,2 mElectric 380 Volt: Back stop with manual adjustment: Shadow line lighting: Foot switch: Demo machine at a special price: The new motor guillotine type SMP is a well dimensioned machine with all-welded link guides. The drive takes place with astandard geared brake motor via a chain connection to the main axle. theknives are of the highest quality. The optimal cutting angle secures thetogether with the sheet holder perfect cuts.Bearings and guides are maintenance and lubrication-free.Standard equipment: • Back gauge 665 with mm scale. •cutting edge lighting. • Section counter. • Table extensions 600 mm. •Right angle stop, left. • Movable 24 V foot switch with em ...
sheet width: 2020 mmplate thickness: 2 mmdaylight upper clamping: 122 mmbending angle max.: 135 °range L-W-H: 2,56 x 0,6 x 1,26 mweight of the machine ca.: 1020 kgUnused exhibition machine at a special price:Segmented top rail for bending box profiles, upper beam clamping hand-operated,manual bending beam actuation with weight compensation, degreescale, adjustable bend stop. Warranty = 12 months for single-shift operation.The bending performance refers to 380 N/mm² strength. Plus freight + packaging 270,--.To complement this, we have a Kapema motorized panel shear, model SMP 20/20, capacity 2050 x 2 mm with manual backgauge, cutting line lighting, etc. Pleaseinquire if you are interested.This is an exhibition machine at a special price, so we are selling it without any warranty.Machine. Machine dealer with own stock of 1600 m².The data for this ad was created with ModulMWS - the softw ...
sheet width - max.: 1010 mmplate thickness: 4.0 mm STplate thickness: 2.5 mm VAplate thickness: 6.0 mm ALUnumber of strokes - loaded: max. 20 Hübe/mincutting angle: 1.5 °work height max.: 900 mmControl: ELGO total power requirement: 5.5 kWweight of the machine ca.: 2200 kg. from a maintenance workshop good condition ()Equipment:- Robust NC electro-hydraulic guillotine shear- NC electro-motorized backgauge Includes NC ELGO positioning control TYP 85- Electric cutting length limiter- Manual cutting gap adjustment- 1x side stop with scale- 2x support arms- 1x freely movable foot switch- Original operating instructions Special accessories included:- Pneumatic holding device for thin sheet metal blanksThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 60 tchamfer lenght: 2050 mmdistance between columns: 1550 mmthroat: 255 mmstroke: 165 mmdayligth: 475 mmworking feed: 9,8 mm/secreturn speed: 117 mm/secajustment speed: 150 mm/sectotal power requirement: 5,5 kWweight of the machine ca.: 5000 kgdimensions of the machine ca.: 2300 x 1500 x 2470 mmEquipment:- DELEM DA65 CNC control- Electric backgauge (X-axis), 600 mm- Hydraulic upper tool clamping- Front light barrier- Side and rear protective grilles- Manually adjustable stop bar, foldable (R+Z-axis)- Upper tool- 2x support arms- Machine feet- Operating instructionsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 750 mmplate length: 1250 mmplate thickness: 4 mmtable surface area: 1600 x 1050 mmno. of strokes: 180 Hub/minmax. punching diameter: 105 mmpunching pressure: 25 ttotal power requirement: 4,0 kWweight of the machine ca.: 1,8 tdimensions: 1,9 x 1,9 x 1,7 mPunching and nibbling machine- Digital readout for X and Y axis- Tool cabinet with toolsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1020 mmplate thickness: 2 mmdistance between columns: 1020 mmbending angle max.: 135 °total power requirement: 0 kWweight of the machine ca.: 0,3 tdimensions of the machine ca.: 1350 x 850 x 1175 mMax. bending angle 135°Manually operated with auxiliary spring on both sides.Upper beam opening 40 mm,Upper and lower beams segmented,Segment division: 25-30-35-40-45-50-75-100-150-200-270 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3000 mmplate thickness: 6 mmdistance between columns: 3200 mmspeed: . m/minrear stop: 1000 mmtotal power requirement: 7,5 kWweight of the machine ca.: tdimensions of the machine ca.: mThe backgauge is electric.The technical data is provided by the manufacturer or operator and is therefore non-binding. We reserve the right to sell the machine prior to sale, our terms and conditions of sale apply exclusively.About usMore than 400 of our own machines in stockOver 15,000 m² of storage space, 70 t crane capacityMore than 10,000 items and accessories for your workshopIf you are interested in selling machines, production lines, or your business,please contact us.You can find further offers on our website.Tours are possible by appointment.We look forward to your visit.Your Markus Hirsch TeamThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
plate thickness: 4 mm STplate thickness: 3 mm VAblade length: 225 mmengine output: 3,5 kWweight of the machine ca.: 650 kgdimensions of the machine ca.: 1250 x 900 x 1100 mmFeatures:- 2x miter stops- 90° fixed angle- Foot switchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1360 mmplate thickness: 06,0 mmdistance between columns: mmtable width: 455 mmwork height max.: 880 mmcutting angle: 1°30 °rear stop: 750 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 3050 mm: 12,0 mm: -: 0,5-3,0 °: 1000 mmtable height: 930 mmwork height max.: 930 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 1000 mmy-travel: 600 mmz-travel: 600 mmcontrol: Heidenhain TNC 426spindle nose: 100-700 mmwork table:: 1.080 x 580 mmworkpiece weight max.: 550 kgT-slots: 7 Stk.T-slot - width: 14 mmtool piece magazine with: 36 Plätzenweight of tools max.: 8 kgtool length - max.: 340 mmtotal power requirement: kWweight of the machine ca.: 6,2 tdimensions of the machine ca.: 4.790 x 5.330 x 2.905 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3050 mmplate thickness: 6.0 mmcutting angle adjustment: 0.5 - 3.0 °down holder: 18 Stückno. of strokes: 8 - 14 Hub/minback stop - adjustable: 750 mmwork height max.: 770 mmControl: SP 8 total power requirement: 7.5 kWweight of the machine ca.: 4800 kg.range L-W-H: 3650 x 2100 x 1750 mm very little use () from a maintenance workshopFeatures- Guide-railed electro-hydraulic guillotine shear- HACO control model NC SP 8 Easy operation directly at the cutting table Adjustment of cutting angle + backgauge Retraction function from rear stop Electric cutting length limitation Emergency stop button, locking - Motor-adjustable and programmable rear stop- Electric/hydraulic cutting angle adjustment- Manual cutting gap adjustment, from the front- 1x side stop - 1,000 mm, with scale & T-slot- Front finger guard- 1x freely movable foot switch- Rear safety guard + sheet metal chute- Ope ...
sheet width - max.: 300 mmplate thickness: 8 mmflat steel: 80 x 10 mmblade length: 300 mmmachine length: 860 mmmachine height: 565 mmweight of the machine ca.: 172 kgLong measuring shearMachine dealer with own stock of 1600 m².The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
plate thickness: 4 mmCutting thickness max. At (60 kg / mm²): 3 mmblade length: 90 mmweight: ca. 30 kgdimensions of the machine ca.: 0,45 x 0,30 x 0,2 mNotching unit for installation under a hydraulic or eccentric press. The cutting thicknesses are estimated to be low.Machine dealer with own stock of 1600 m².The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 220 tchamfer lenght: 3720 mmdistance between columns: 3020 mmcolumn arm: 400 mmajustment speed: 125 mm/secworking feed: 10.0 mm/secreturn speed: 132 mm/secback stop - adjustable: 800 mmstroke: 275 mmdayligth: 550 mmtable height: 900 mmoil volume: 300 ltr.total power requirement: 18.5 kWweight of the machine ca.: 12800 kg.range L-W-H: 5850 x 2220 x 2820 mm Good condition Current new price approx. 100.000 euros Special price on requestFeatures:- Electro-hydraulic CNC press brake- With DELEM CNC control model DA 66W 2D graphic programming Automatic bend sequence calculation and collision detection High-quality color LCD screen (TFT) - Swivel control panel, front left- CNC-controlled axes: Y1 + Y2 + X + R + crowning - CNC electric motor-driven backgauge (X axis)- CNC electric motor height adjustment of the backgauge (R axis)- CNC electric motor-driven bending table crowning- 2x man ...
sheet width: 2000 mmplate thickness: 3 mmrear stop: von Hand, 750 mmnumber of support arms: 2 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 170 tchamfer lenght: 4080 mmdistance between columns: 3680 mmcolumn arm: 410 mmdayligth: 385 mmstroke: 215 mmajustment speed: 200 mm/secworking feed: 1-10 mm/secreturn speed: 135 mm/sectable width: 200 mmtable height: 1050 mmNumber of working hours: 25.430 hoil volume: 350 ltotal power requirement: 29 KVAweight of the machine ca.: 16.450 kg.range L-W-H: 4620 x 2210 x 2885 mm Machine in good condition Regularly serviced by the manufacturer CNC backgauge with 8 axes ()- in checked conditions - machinevideo - https://www.youtube.com/watch?v=yEaRj0XJAC4Equipment:- CNC electro-hydraulic press brake/die bending press- DELEM CNC control - swiveling front left High-resolution graphic screen Clear, concise menus in the operators language Large tool and product library Graphic 2D programming Automatic bend sequence calculation and collision detection Emergency stop button at front - CNC ...
